Auto Page Professional Vehicle Security System RF-315 Operation Manual

THIS PRODUCT IS DESIGNED FOR PRO

FESIONAL INSTALLATION ONLY

RF-315

PROFESSIONAL VEHICLE SECURITY SYSTEM

OPERATION MANUAL

TRANSMITTER OPERATION:

Transmitter

Button

-

+

-

-

II

Lock Doors & Arm System
Panic function Press and Hold for 3 seconds
Car Locator Under armed mode
Arm and Delete The 2 Stage Shock

Sensor
Silent Arming / Disarming Ignition in "off" position.

Unlock Doors & Disarm System
Two Steps Door Unlock & Disarm

System
Trunk Release (Channel 2) Press and Hold for 2 seconds

Passive Arming By-pass While the system Disarmed.
Silent Arming / Disarming or 3rd ch

Switching code For 2nd Car
Operation.

System Function Remark

Press twice within 3 seconds

Press twice within 3 seconds.

For regular remote transmitter Only

ACTIVE ARMING – LOCK & ARM:

1. Press button on transmitter.

2. The siren will chirp once and parking light will flash once indicating that the system is now
armed. The vehicle doors will lock upon arming when interfaced with the security system.

Note: Defective sensor reminder: If the siren sounds 3 chirps, then you have left a door,
trunk, or hood lid ajar.

SILENT ARMING / DISARMING: Press the button on the transmitter to arm or disarm
your security system with no chirp sound heard; arm / disarm confirmation will be through the
vehicles parking lights only.

SHOCK SENSOR / OPTIONAL SENSOR BY-PASS: Press the button on the transmitter

twice within 3 seconds will arm the security system, by-pass the shock sensor or the optional
sensor connected to 4 pin plug. The system will chirp one additional time to confirm the
sensor bypass mode was activated. The sensor bypass feature is programmed to activate for
one arming cycle only. The security system will return to normal operation during the next
arming cycle.

PASSIVE ARMING:

Active arming / disarming is controlling your security system via the remote transmitter. This
security system is equipped with an optional Passive Arming feature, which allows the
security system to arm 30 seconds after the last door is closed. Operation is as follows.

1. Turn the ignition to the “OFF” position and exit the vehicle. After all entrances are closed,
the security system LED will flash fast for 30 seconds. If you reopen any door / hood /
trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle
entrances are closed.

2. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren
will chirp [1] time and the parking lights will flash [1] time.

2

PASSIVE DOOR LOCKING:

The vehicle doors will automatically lock after passive arming cycle has been completed.

ACTIVE DISARMING – UNLOCK & DISARM:

1. Press the

2. The siren will chirp twice and parking lights will flash twice to indicate that the security
system is now disarmed. The vehicle doors will unlock and disarm when interfaced with the
security system.

TAMPER DISARMING: If the alarm is triggered; upon disarm the system, the siren will chirp 4
times and parking lights will flash 3 times.

TWO STEP DOOR UNLOCK: This feature will independently unlock the driver’s door only when
disarming the security system. Pushing the button on the transmitter a second time within 3

seconds will unlock the entire vehicle.
AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm

itself 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door
is opened before the 60 seconds timer has elapsed.

DISARMING WITHOUT A TRANSMITTER

The Override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)

2. Within 10 seconds push and release the valet switch The alarm will stop sounding and

VALET MODE:

The valet switch allows you to temporarily bypass all alarm function, eliminating the need to
hand your transmitter to parking attendants or garage mechanics. When the system is in
valet mode, all alarm functions are bypassed, however, the remote panic feature and remote
door locks will remain operational.

Enter Valet Mode:

1. Turn the ignition to “ON” position.

2. Push and hold valet switch for 2 seconds or until the LED turns on. The LED will remain on
as long as the system is in 'valet mode'.

Exit Valet Mode:

1. Return to normal operation, turn ignition 'ON'.

2. Push and hold valet switch for 2 seconds; the LED will turn off indicating the system is
exiting the valet mode.

PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trigger the alarm in case of
emergency.

1. Press and hold the button on the transmitter for 3 seconds. The alarm will immediately

2. To stop the alarm, press and hold the or button on the transmitter, the panic mode

3. If the button is not pressed, the alarm will automatically stop after 30 seconds.

button on the transmitter.

enter the disarm mode. You can now start and operate the vehicle normally.

sound.

will be turned off immediately.

3