AutoPage CPX-2200 Operation Manual

CPX-2200 WIRE DIAGRAM

87a

To start solenoid

Car-Pro

By:

Professional Vehicle Security

CPX-2200

H1: 10 pin main harness

H2: 3-pin sensor harness

H3: 2-pin LED harness

INSTALLATION & OPERATIONS

MANUAL

H4: 3-pin door lock harness

H1: 10 PIN HARNESS

AUTOPAGE INC.

1815 West 205th Street Suite 101

Torrance, California 90501-1525

Main Office: 310-618-2002

Customer Service: 800-262-2527 Ext. 462

www.autopageusa.com

Car-Pro CPX-2200

wire: Instant trigger ground input

Blue

wire: Positive door trigger input

. Violet

wire: Negative door trigger input

Green

wire: To Ignition switch + 12V

Yellow

wire: to constant battery +12v

Red

wire: Positive output to siren

Brown

wire: Ground to vehicle

Black

10.

wire: 200 mA Ground output when arm

Orange

Red/White

White

wire: Parking light relay power input

wire: Parking light relay output

Blue (-) 200mA Unlock Green (-) 200mA Lock

12V

From ignition switch

oooo

12V

15A Fuse

A. TRANSMITTER CODE LEARNING: Note: This security system will only retain the last 4 remote transmitters programmed. If the

transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order.

1. Disarm the system.

2. Open the Door and keep the door open

3. Turn the ignition key “ OFF / ON “ 6 times, keep at “ON” position at 6th time switching, you will get 6 chirps to confirm enter transmitter programming.

4. Within 15 seconds press & hold any button for transmitter code learning, a long chirp confirm transmitter programmed.

5. Apply steps 4 – 5 to program 2nd, 3rd and 4th transmitter.

Exit: Turn the ignition off, 3 long chirps confirm exit. B. FEATURE PROGRAMMING

1. Disarm the system.

2. Open the Door and keep the door open.

3. Turn the ignition key “ OFF / ON “ 3 times stay in on position. (3 chirps to confirm in programming mode)

4. Within 15 seconds press button “ I + II “ to select the feature which you want to program. See the features programming table below to select the desired features, which you want to program. Note the number of siren chirps to confirm the selected feature(s).

5. Press the button “ I “ or “ II “ on the transmitter to enable or disable the specific feature.

6. Repeat steps 4 - 5 for any other features you wish to program.

Number of pressing

button I + II & chirps

1 2 3 4 5

Exit: Turn the ignition off, or close the door, 3 long chirps confirm exit. C. PASSWORD SETUP:

1. Disarm the system.

2. Open the Door and keep the door open

3. Turn the ignition key “ OFF / ON” 9 times for “New Password Pin Code Setting” and keep at “ON” position at 9th time switching.

4. After 2-second pause, the siren will chirp 9 times to confirm entry.

5. Within 15 seconds, begin to enter your chosen 1 – 9 digit by pressing and releasing the transmitter button “I” from 1-9 times

6. Press button “ II ” to get out of password setup mode, corresponding to the new password code report by siren chirp confirmation.

Note: Default setting of password code from the factory is “ 1”.

Program feature Press button “ I “

PROGRAMMING

/ one long chirp

Factory Setting

0.9 sec. 3.5 sec. Disable Enable

Enable Disable

-jacking Disable Enable Enable Disable

Press button “ II “ / Two long chirps

CPX-2200 OPERATION MANUAL

Starter

Unlocking

TRANSMITTER OPERATION:

Transmitter Button Feature Remark

Button – Button

Button Button for 3 seconds

Button

Button for 2 seconds

+ Button

+ Button for 2 seconds

A. ACTIVE ARMING – LOCK & ARM:

1. Press button on transmitter.

2. The siren chirps once and parking lights flash once indicating the system is now armed. The vehicle doors will lock upon arming when interfaced with the security system.

DOOR AJAR WARNING: When you arm the system and the siren chirps 3 times, it means you have left a door or trunk, or hood lid ajar. You should check and find out the defective protecting point. SHOCK SENSOR / OPTIONAL SENSOR BY-PASS: Press button twice within 3 seconds to arm the security system, by-pass shock sensor connected to 3-pin plug. The system will chirp one additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to the original program setting for the next arming cycle.

SILENT ARMING / DISARMING: Press + button together to arm or disarm your security system. No chirp sound will be heard; arm / disarm confirmation will be through the vehicle’s parking lights only.

B. PASSIVE ARMING

This system is equipped with passive arming feature, which allows the system to arm itself in 30

seconds after the last door is closed; operation is as follows:

1. Turn ignition to OFF position and exit the vehicle

2. After all entrances are closed, the system will start counting and LED flashes for 30 sec., if you re-open any door / trunk / hood the system will stop counting and the LED will stop flashing. It will start re-counting again once all vehicles’ entrances are closed.

3. After 30 seconds has elapsed, the security system will automatically “ARM”. The siren will chirp once and the parking lights will flash once.

REMOTE PASSIVE:

You can use the remote transmitter to both enter and to exit the passive mode, eliminating the need to hand your transmitter to parking attendants or garage mechanics.

a). Press and release button for 2 seconds. The system will enter the passive mode. One long chirp confirms entry to the passive mode.

b). Press and release button for 2 seconds. The system will exit the passive mode. Two long chirps confirm exit of the passive mode.

PASSIVE DOOR LOCKING

The vehicle doors will automatically lock after passive arming cycle has been completed.

C. ACTIVE DISARMING – UNLOCK & DISARM:

Press button on the transmitter, the siren will chirp twice and parking lights will flash twice to indicate the security system is now disarmed. The vehicle doors will unlock when interfaced with

the security system.

TAMPER DISARMING: If the alarm has been triggered, upon disarming the system, the siren will chirp 4 times and the parking lights will flash 3 or 4 times.

Arm / Door lock Arm and Delete Optional Sensor Press twice within 3

Car Locator Under arm mode Panic Press & hold 3 seconds Disarm & door unlock

In or Out Passive mode Press & hold 2 seconds

Silent arm / disarm

Anti car-jacking

seconds.

Under ignition off

Under ignition on

AUTO RE-ARM: The security system will auto re-arm itself within 30 seconds after disarming by

remote transmitter. Auto re-arm will be canceled if any protected door has been opened before the 30 seconds timer has elapsed.

PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trigger the alarm in case of emergency.

1. Under the arming mode press and hold button for over 3 seconds. The siren will sound and the parking lights will flash.

To stop the panic mode press or button and the panic mode will turn off immediately.

If the button is not pressed, the alarm will automatically stop in 30 seconds.

D. TRIGGER THE SYSTEM

When the alarm system is armed, your vehicle is protected as follows:

1. Light impact will trigger the warn-away signal. A long chirp from siren.

2. Heavy impact / Door open / Hood open / Trunk open / Turning on the ignition switch; all will trigger the programmed sequence.

For above (2) The siren and parking light will turn on, alerting of an intrusion for 30 seconds. Then it will stop and automatic reset / re-arm. If any one of the sensors or detectors is still active, the alarm system will sound a maximum of 3 times of 30 seconds cycles. The starter disable relay (if

installed) prevents the vehicle’s starter from cranking.

E. ANTI CAR - JACKING

Warning: If you don't need anti car-jacking function in this alarm system, be sure to set anti car-

jacking feature “DISABLE”. This system is default setting all anti car-jacking “ DISABLE ”.

1). With the Ignition “on”, press and hold + button on the transmitter for over 2 seconds. The parking light will turn on for 2 seconds to indicate activation of anti car – jacking mode.

2). TRIGGER THE ANTI CAR - JACKING MODE:

3-timer circuits will function as follows:

First timer:

1. 50 seconds after the system has been triggered, the siren will start chirping for 15 seconds.

2. During this 15 seconds period of chirping, you will be alerted to press and hold + button on the transmitter for over 2 seconds to turn off the anti car-jacking feature; parking lights will flash twice and siren will chirp twice confirming success in turning off the anti car-jacking mode.

3. If not, it will enter the second timer of anti car- jacking feature

Second timer:

65 seconds after the system has been triggered. The siren start sounding and the parking lights will start flashing.

Third timer:

90 seconds after the system has been triggered

a. The siren will continue sounding and the parking lights flashing, and b. The starter disable will activate to prevent vehicle from starting. c. It will remain active until the vehicle’s battery power exhausted.

F. DISARMING WITHOUT A TRANSMITTER

The Override function may be used if the remote transmitter is lost or inoperative.

1. Turn ignition switch to 'ON’ position and the LED will start flashing, indicating the system has entered the password override mode.

Once the LED has flashed the same number of times as your password number, then turn the ignition key “OFF”; the alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally.

Example: If your programmed Password Code is “ 5 ” you would;

1. Turn the ignition switch to the 'ON’ position and the LED will start flashing, indicating the system has entered the password override mode.

2. Wait until the LED flashes for the 5th time, then the turn ignition key OFF immediately.

The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally.

G. IGNITION CONTROL DOOR LOCK.

If the vehicles’ door locks have been interfaced to the security system, the system will automatically lock the vehicle's door when the ignition “ON” and unlock vehicle’s door when ignition “OFF”.

H. CAR LOCATOR Under the armed mode press button to activate car locator, siren will chirp 6 times and parking lights flash 12 times for you to easily locate your car.

LED INDICATORS:

LED Function Off Disarmed Slow flash Armed Fast flash Passive arming

CHIRP INDICATORS:

Chirp Function 1 chirps Arm

2 chirps Disarm 3 chirps Door ajar warming

4 chirps Disarm / system trigger 6 chirps Car locator

PARKING LIGHTS:

Parking light Function 1 flash Arm

2 flashes Disarm 3 flashes Disarm / trigger on ignition or door

4 flashes Disarm / trigger on shock sensor 12 flashes Car locator

ALARM OPERATION CONDITIONS:

Siren Parking Arming 1 or 3

Chips

Disarming 2 or 4

Chirps Trigger Alarming Flashes Slow Panic Alarming Flashes Slow

pin switch

Light 1 Flash Slow

2 or 3 or 4 Flashes

LED Door

Flash Off or Fast Flash

Flash Flash

Locking On

“CUT”

Off

On On