AutoPage C3-RS915LCD User Manual

THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY

C3-RS-915 LCD

PROFESSIONAL 2-WAY LCD REMOTE CAR STARTER & ALARM

SYSTEM

With

Built in Temperature & Voltage Sensor

And Two-way Serial Port Data Link

Compatible

OPERATION MANUAL

Please register your product at:

www.autopageusa.com

Congratulations on your purchase of the RS-915 LCD remote start vehicle security system. We sincerely hope

the purchase of the RS-915 remote start security system gives peace of mind to you.

The RS-915 LCD is a state-of-the-art two-way communication system. Please take the time to read over this manual to thoroughly familiarize your self with the many features and options of the RS-915 LCD.

WARNINGS:

As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is corrected.

8. The use and operations of this system is the sole responsibility of the operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.

10.It is not safe to remote start the vehicle if the vehicle is parked on a steep incline.

LCD REMOTE CONTROL TRANSCEIVER: XT-915 LCD

A. BATTERY CHARGING:

This system has a built in rechargeable power source. Please charge the battery fully with the supplied charger before initial use. Depending on the usage, the remote should be charged at least once a month. Do not use other chargers on this remote as they could damage the rechargeable batteries. The 1-way remote is powered by a pair of 3V, CR2016 batteries.

Battery Level Indicator (2-way remote)

The Battery Level indicator has three level indicators that serve as a visual indication of battery charge. When the battery reaches a low charge level that requires charging, the remote control will generate a single notification chirp, and the Battery Level indicator will flash continuously.

C3 RS915 REV. O1

B. STANDARD LCD ICON CONFIGURATIONS:

The lock icon will be displayed when the door locked.

The unlock icon will be displayed when the door unlock

Sensor Bypass

Sensor 1 bypass under Arm mode

Hidden Alarm Mode The security system arm with hidden alarm function (silent alarm)

Valet Mode

Remote start and alarm functions shall be temporarily on hold.

Hood Trigger

Hood is illegally opened (Zone 1)

Trunk Trigger

Trunk is illegally opened (Zone 2)

Door Open Warning

Doors are illegally opened (Zone 3)

Sensor Trigger

Trigger on Sensor 1 (Zone 4)

Ignition Trigger

Ignition switch is illegally turned on (Zone 5)

System trigger

Remote Transmission

You are transmitting the signal to control unit

In – Range Indicator

You are within the range of the remote control.

Anti Car-Jack Mode

Activate the anti car-jacking mode

Icon flash under check mode

Engine Cranking

Your vehicle engine Cranking by remote control

Engine Running

Your vehicle's engine is running

Timer Control Start

Engine start automatically every 2 or 3 hours.

Daily Start

Engine start automatically at the same time next day

Temperature Start

Engine start automatically when reach programmed temperature.

Turbo Timer

Turbo timer was set up

Manual Gear

Engine Start Memorizing for the car with manual gear was set up

Activate Channel 3 (Trunk Release). Activate Channel 3

Activate Channel 4

12:00

Time Monitor

12:00

Alarm Clock

You have set morning call alarm

Parking Meter

Reminder when time is up for parking

Low Battery

You have to charge the battery of remote control.

Melody Mode

Remote Control alert user through melody sound

Vibration Mode

Remote Control vibrates when the system is triggered

C3 RS915 REV. O1

OPERATION:

Transmitter

Button

System Function

Remark

Lock Doors & Arm System

Panic function

Press and Hold for 3 seconds. Press Trunk

button to stop panic function

Car Locator

Press when in armed mode

Arm and Delete The 2 Stage Shock

Sensor

Press twice within 3 seconds. Pass will

appear on the remote

Arm System and Hidden Alarm

Function

Press within 3 seconds and Hold

button for 2 seconds

Silent Arming / Disarming

Ignition in "off" position.

Active Anti Car-Jacking Mode

Ignition in "on" position press and hold for 2

seconds

Unlock Doors & Disarm System

Two Steps Door Unlock & Disarm

System(optional)

Press twice within 3 seconds.

Trunk Release (Channel 3)

Press and Hold for 2 seconds

Passive Arming By-pass

While the system Disarmed.

Activate or Turn Off The Remote Start

Press button once. Press Twice if set to

start safety mode

Channel # 4 Timer Output (4)

Optional

Channel # 5 Timer Output (5)

Channel # 6 Timer Output (6)

Switching code For 2nd Car

Operation.

For regular XT-33 remote transmitter Only

Chirp

Function

Parking light

Function

1 chirp

Arm

1 flash

Arm

2 chirps

Disarm

2 flashes

Disarm

3 chirps

Defective Reminder

3 flashes

Disarm / Triggered

4 chirps

Disarm / Triggered

12 flashes

Car Locator

6 chirps

Car Locator

Constant On

Under Remote Start

Siren / Horn

Parking Light

LED

Doors

Starter

Dome Light

1. Arming

1 or 3 Chirps

1 Flash

Slow Flash

Locking

Disable

2. Disarming

2 or 4 Chirps

2 or 3 Flashes

Unlocking

Turns on for 30

-second

3. Trigger

Alarming

Flashes

Slow Flash

Disable

Flashes

4. Passive Starter

Disable

Fast Flash

Disable

5. Panic

Alarming

Flashes

6. Car-Jacking

Alarming

Flashes

Disable

Flashes

7. Car Locator

6 Chirps

12 Flashes

Locking

C: REMOTE TRANSMITTER OPERATION:

D CHIRP INDICATORS: PARKING LIGHT:

ALARM OPERATING CONDITION:

C3 RS915 REV. O1

E. ACTIVE ARMING – LOCK & ARM:

1. Press button on the transmitter.

2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The

vehicle’s doors will lock upon arming if interfaced with the security system.

DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.

SILENT ARMING / DISARMING: Press the transmitter and buttons at the same time. This will arm or disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only.

SENSOR BY-PASS:

The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle.

Sensor By-Pass : Press the button two times within 5 seconds will arm the security system and by-pass the shock sensor.

HIDDEN ALARM FUNCTION: Silent Alarm Press the button first; within 3 seconds press the button to activate the hidden alarm function.

The security system will arm and with “Hidden Alarm Function” The siren / horn will be silenced

even if the sensor is triggered in the armed mode. Alarm indication will only appear on the LCD

Transmitter.

F. PASSIVE ARMING (Programmable)

Active arming / disarming is controlled by your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows.

1. Turn the ignition to the “OFF” position and exit the vehicle.

2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle entrances are closed.

3. After the 30-second time has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time and the parking lights will flash [1] time.

PASSIVE ARMING WITH PASSIVE DOOR LOCKING

The vehicle doors will automatically lock after the passive arming cycle has been completed.

PASSIVE ARMING BY-PASS:

respond with [1] chirp and LED will turn “ON”. The security system will remain in this temporary state for as

long as you wish. To exit passive by-pass, press the transmitter or buttons and the system will return to normal status.

While the system is disarmed, Press the button twice, the system will

G. ACTIVE DISARMING – UNLOCK & DISARM:

1. Press button on the transmitter.

2. The siren will chirp twice and the parking lights will flash twice indicating that the security system is now disarmed. The vehicle’s doors will unlock and the dome light will turn on for 30 seconds upon disarming. (Note: Power door locks and dome light must be installed with the security system.)

TAMPER DISARMING: If the alarm is triggered, upon disarm the system’s siren will chirp 4 times, and the parking lights will flash 3 times telling you the alarm has been triggered during the last armed state.

PATHWAY ILLUMINATION: When receiving an unlock /disarm signal, this feature will turn the parking lights “ON” for 30 seconds and for 10 seconds upon the lock signal. (Programmable)

C3 RS915 REV. O1

TWO STEPS DOOR UNLOCK (Optional): This feature will independently unlock the driver’s door only when

disarming the security system. Pushing the button a second time within 3 seconds will unlock the other doors.

AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself in 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed.

H. DISARMING WITHOUT A TRANSMITTER

OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)

The Override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to the 'ON’ position.

2. (Alarm will sound.)

3. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally.

OVERRIDE THE ALARM WITH PASSWORD PIN CODE:

Unlike valet switch that can easily be found and defeated, this security system allows the consumer to program a password pin code offering a higher level of security.

1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)

2. Within 5 seconds, enter your chosen first digit code by pressing and releasing the Valet Switch.

(When finished above procedures, system's siren will stop alarming, lights will stop flashing, but the vehicle can’t be started.)

3. Within 15 seconds of the last digit code enter (the 1st code), then turn the Ignition Switch “OFF”

and then “ON”.

4. Within 15 seconds, enter your chosen second digit code by pressing and releasing the Valet

Switch.

5. Turn the ignition switch “OFF” position. 4 Chirps from siren/horn and 3 flashes from the parking

light indicate the system has disarmed.

Note: You must override the alarm within 60 seconds. If not, the system will automatically re-arm.

EXAMPLE: To Override the System with the Password Code 83,

1. Enter the vehicle and turn the ignition switch to the 'ON’ position. (Alarm will sound.)

2. Within 5 seconds, Press and Release the Valet Switch 8 times, (When finished the system's siren will stop alarming, lights stop flashing, but the vehicle cannot be started or driven away.)

3. Within 15 seconds of entering the last digit code enter (the 1st code), turn the Ignition Switch “Off” and then “ON”.

4. Within 15 seconds, Press and Release the Valet Switch 3 times.

5. Turn the Ignition Switch to the “Off” position. 4 Chirps form siren/horn and 3 flashes from the parking lights will indicate the system has disarmed.

I. VALET MODE:

VALET MODE: (System is in Disarm Mode)

The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions and remote start functions are bypassed, however, the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed either by using your remote transmitter, or by operating the Manual Override sequence.

C3 RS915 REV. O1

+ 14 hidden pages