Auto Page C3-RS-665-2W Operation Manual

1

C3-RS-665-2W

PROFESSIONAL TWO WAY REMOTE CAR

STARTER

&

3 CHANNEL SECURITY SYSTEM

OPERATIONS MANUAL

Compatible

Please register your product at:

www.autopageusa.com

THIS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY

2

SYSTEM OPERATIONS:

WARNINGS:

As with any product that performs automatic functions, there are certain safety
precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is
corrected.

8. The use and operations of this system is the sole responsibility of the
operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle
running on public st reets.

10. It is not safe to remote start the vehicle if the vehicle is parked on a steep

incline.

Transmitter

Button

System Function Remark

Lock Doors & Arm System
Panic function

Press and Hold for 3 seconds.
Press to stop panic.

Car Locator Under armed mode

-

Arm and Delete The 2 Stage Shock
Sensor

Press twice within 3 seconds

+

Silent Arming / Disarming Ignition in "off" position.
Unlock Doors & Disarm System

-

Two Steps Door Unlock & Disarm
System

Press twice within 3 seconds.

Trunk Release (Channel 2) Press and Hold for 2 seconds

-

Passive Arming By-pass While the system Disarmed.
Activate or Turn Off The Remote

Start

Safety start requires two pushes

+

Channel # 3 Auxiliary Output Press both buttons together

3

II

Switching code For 2nd Car
Operation.

For regular remote transmitter Only

XT-43 LCD TRANSMITTER OPERATION:

LCD REMOTE CONTROL TRANSMITTER:

BATTERY REPLACEMENT:

A 1.5V type AAA Alkaline
battery powers the Remot e
Transmitter. When the power of

the battery weakens a
icon shall be displayed on the
LCD screen. When the old
battery is replaced with a new
one, there will be beep sounds
indicate the power is up.

Note: Press the button two

Note: If the system is interfered by stronger radio

frequency around, sources of high voltage
electric power or such obstacles like tall
buildings and so on, the transmission range
may get shorter as the system uses low output
powered frequency.

AAA

4

times when the battery
compartment is empty, and
then insert the new battery.

THE REMOTE LCD ICONS WITH FUNCTION:

Door Lock

Your vehicle doors are
locked.

Door Unlock Your vehicle
doors are unlocked

Start Mode

Your vehicle is running

Valet Mode

All the function shall be
temporarily on hold.

Remote Transmission

You are transmitting the
signal to control unit

In – Range Indicator
You are within the remote
control range.

Trunk Release Trunk
open. Trunk symbol only.

Low Batte ry
You have to replace the

battery of remote control.
Vibration Mode
Remote Control vibrates
when the system is
triggered

Ignition On

Power Save Mode

Save the battery power

PROGRAM MODE FOR LCD REMOTE CONTROL TRANSCEIVER:

Press and hold all four remote control buttons simultaneously unit

5

one long beep is heard. LCD Programming has now been entered.

Transceiver Button System Function Remark
Program Mode -

Switching code for 2nd / 1st
Car Operation

Press within 5
seconds

Program Mode -

Melody / Vibration Mode Press within 5

seconds

Program Mode -

Power Save Mode Press within 5

seconds
LCD screen lamp turns on for
5 seconds.

- +

Clear the Flash Icon and
Melody Sound

Press within 3

seconds

ACTIVE LOCK:

1. Press button on the transmitter.

2. The Siren will chirp once and parking lights will flash once indicating that
the system is now active. The vehicle doors will lock upon activating
only when interfaced with the keyless entry system.

SILENT LOCKING / UNLOCKING: Pressing the + buttons
together on the transmitter will lock or unlock your system, No chirp sound
will be heard. Lock / unlock confirmation will be seen through the
vehicle’s parking lights only.

ACTIVE UNLOCK:

1. Press button on the transmitter.

2. The horn will chirp twice and parking light will flash twice to indicating

that the keyless system is now unlocked. The vehicle doors will
unlock and dome lights will turn on for 30 seconds.

2-way LCD Remote Control Transceiver:

2nd Car Operation: While the “II” icon display on the LCD screen, you can
remote control and communicate with a second Autopage AM frequency
security system. It has two short “beep” sounds while pressing any button
of the LCD screen transceiver

6

1. Press and hold all four remote control buttons
simultaneously unit one long beep is heard. LCD
Programming has now been entered.

2. Within 5 seconds press and hold button until two
beeping sounds are heard and the “II”

icon will

display on the LCD screen to indicate the second

transceiver pin code has been initiated.

3. To exit programming mode, take no action for five

seconds. The remote control will generate two long

beeps to indicate programming mode has been

exited.

Back to first Car Operation:
This will allow you to control and communicate with the first vehicles

security system.

1. Press and hold all four remote control buttons

simultaneously unit one long beep is heard.

Programming has now been entered.

2. Within 5 seconds press and hold button until one
beep sound is heard.

3. To exit programming mode, take no action for five

seconds. The remote control will generate two long

beeps to indicate programming mode has been

exited.

Vibration / Melody Mode:

Vibration mode is useful when you are in a noisy place and it is difficult to
hear the beep sound from the remote control. In this mode the unit will
vibrate if your security system is triggered.

1. Press and hold all four remote control buttons

simultaneously until

one long beep is heard.

Programming has now been entered.

2. Within 5 seconds, press the

button to select the

mode of vibration or melody, the

icon will

displayed

on the LCD screen to show the LCD

remote transceiver is in vibration mode.

3. To exit programming mode, take no action for five

seconds. The remo

te control will generate two long

beeps to indicate programming mode has been