AutoPage C3-RS603 User Manual

C3-RS-603

PROFESSIONAL REMOTE CAR STARTER

KEYLESS ENTRY SYSTEM

With Two-way Serial Port Data Link

Compatible

OPERATIONS MANUAL

Please register your product at

www.autopageusa.com

THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY

SYSTEM OPERATIONS:

WARNINGS:

As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is corrected.

8. The use and operations of this system is the sole responsibility of the operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.

10. THIS DEVISE CANNOT BE USED IN ANY STANDARD TRANSMISSION VEHICLE. FOR AUTOMATIC TRANSMISSIONS ONLY!

Standard XT-33, 5 Button remote

XT-33

Transmitter

Button

Lock Doors Unlock Doors Trunk Release (Channel 3) Press and Hold for 2 seconds

Activate The Remote Start Push twice to start Stop remote start operation

Switching code For 2nd Car Operation.

The first push of the button will send an unlock signal to the doors and the

second push will stop the engine. This is used in the optional XT-11 Ultra Miniature start only transmitter. For normal use with standard XT-33, Use the unlock button before entering the vehicle.

System Function Remark

Push Twice to stop engine For regular remote transmitter

Only

OPTIONAL: XT-11 Ultra Miniature Remote is for start only.

This optional remote can be used in applications where the factory keyless entry system is the main source for arming/locking and disarming/unlocking the vehicle. For example, vehicles with the factory smart key/ “push button” start or one-piece remote with key, an XT-11 Ultra Miniature remote may be purchased for remote start and unlock only applications. This ultra small remote may be preferred if your factory remote is integrated within your key.

CHANGING THE BATTERY IN YOUR TRANSMITTERS XT-33: The XT-33 transmitter uses two (2) 3-volt lithium ion batteries

(#CR2016) that are sandwiched together with the (+) side facing upward. To replace the battery, you will need to use a small flat blade screwdriver. Locate the small notch on the lower right side of the transmitter case next to the key ring. Using the flat blade screwdriver, carefully pry the top case from the bottom case. It should snap apart after breaking the seal. Before removing the batteries note the direction of the positive (+) terminal. Place the new batteries in exactly the same manner, being careful not to bend or damage the contact terminal. Snap the cases back together and then test the transmitter to insure it arms and disarms the alarm.

(2) CR2016

3-Volt Batteries

ACTIVE LOCK:

1. Press

button on the transmitter.

2. The horn, if installed will chirp once and parking lights will flash once indicating that the system is now active. The vehicle doors will lock upon activating when interfaced with the keyless entry system.

ACTIVE UNLOCK:

1. Press

button on the transmitter.

2. The horn will chirp twice and parking light will flash twice to indicating

that the keyless system is now unlocked. The vehicle doors will unlock and dome lights will turn on for 30 seconds.

Optional XT-11 Operations:

1) To remote start the vehicle using the XT-11 press the button twice.

2) To unlock the vehicle on approach, Press the If the button is pressed again within 3 seconds, the remote starter will shut down. Note: If the vehicle can be unlocked with the factory remote, this is the preferred method. If the factory remote will not operate when the engine is running, the unlock wire of the RS-603 must be connected. It is recommended that the unit is programmed to lock before and after start to insure that the vehicle is always secure. Please see install manual page 12 feature II programming.

button once to unlock the doors.

LED DISPLAY:

LED Function

Off Unlock

Slow

Flash

On (Solid) Valet Mode

Locked

CHIRP INDICATOR:

Chirp Function

1 chirp

2 chirps

Lock

Unlock

PARKING LIGHTS:

Parking light Function

1 flash

2 flashes

Constant On

Lock

Unlock

Under Remote Start

DEACTIVATING WITHOUT A TRANSMITTER

The Override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to ‘ON’ position.

2. Within 10 seconds push and release the valet switch

VALET MODE:

The valet switch allows you to temporarily bypass all system function, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, and remote start functions are bypassed, Enter Valet Mode:

1. From the Unlock condition, turn the ignition to “ON” position.

2. Push and hold valet switch for 2 seconds until the LED turns on. The LED will remain on as long as the system is in ‘valet mode’.

Exit Valet Mode:

1. Return to normal operation, turn ignition ‘on’.

2. Push and hold valet switch for 2 seconds, The LED will turn off

indicating the system has exited the valet mode.

IGNITION CONTROL DOOR LOCKS.

If the vehicle’s door locks have been interfaced to the security system, the system will automatically lock the vehicle’s doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”.

TRUNK RELEASE (Additional Installation Required)

Press and hold the

button on transmitter for two seconds to remote

+ 8 hidden pages