AUO M270HW02 V0 Specification
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
() Preliminary Specification
(V) Final Specification
Module
27” Color TFT-LCD
M270HW02 V0
Model Name
Customer Date
Approved by
M270HW02 V0
Approved by Date
Winnie Chang
Prepared by
2011/1/5
Note: This Specification is subject to
change without notice.
document version 1.0 1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Jeff Feng
Desktop Display Business Group /
AU Optronics corporation
2011/1/5
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M270HW02 V0
Contents
1.0 Handling Precautions ........................................................................................ 4
2.0 General Description ........................................................................................... 5
2.1 Display Characteristics ...................................................................................................... 5
2.2 Optical Characteristics....................................................................................................... 6
3.0 Functional Block Diagram ............................................................................... 10
4.0 Absolute Maximum Ratings ............................................................................ 11
4.1 TFT LCD Module..............................................................................................................11
4.2 Backlight Unit ................................................................................................................... 11
4.3 Absolute Ratings of Environment..................................................................................... 11
5.0 Electrical characteristics ................................................................................. 12
5.1 TFT LCD Module.............................................................................................................. 12
5.1.1 Power Specification ................................................................................................................................ 12
5.1.2 Signal Electrical Characteristics .............................................................................................................. 13
5.2 Backlight Unit ................................................................................................................... 15
6.0 Signal Characteristic........................................................................................ 16
6.1 Pixel Format Image .......................................................................................................... 16
6.2 The input data format....................................................................................................... 16
6.3 Signal Description............................................................................................................ 17
6.4 Timing Characteristics...................................................................................................... 19
6.5 Timing diagram ................................................................................................................20
6.6 Power ON/OFF Sequence ............................................................................................... 20
7.0 Connector & Pin Assignment.......................................................................... 22
7.1 TFT LCD Module.............................................................................................................. 22
7.1.1 Pin Assignment....................................................................................................................................... 22
7.2 Recommend connector for Backlight Unit........................................................................ 23
7.2.1 Pin assignment ....................................................................................................................................... 23
8.0 Reliability Test .................................................................................................. 24
9.0 Shipping Label.................................................................................................. 25
10.0 Mechanical Characteristics ........................................................................... 26
document version 1.0 2
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M270HW02 V0
Record of Revision
Version and Date
Version 0.2, 9/10 6
Version 0.3, 10/5 4 N/A
Version 0.3, 10/5 5 N/A TCO Compiance TCO 5.1 Compiance
Version 0.3, 10/5 6
Version 0.4,11/29 5
Pag
e
Color / Chromaticity
Coordinates (CIE) Rx,y Gx,y Bx,y have spec
The spec of Color / Chromaticity are
TBD.
Power consumption 28.8W, black
pattern.
Old description New Description Remark
Change spec to TBD due to color will
be finalized in CS stage.
13) Please avoid touching COF
position while you are doing
mechanical design.
Fill in the color spec instead of TBD.
Power consumption 29.1W, white
pattern.
Version 0.4,11/29 6 Gray to Gray(16x16 avg.) is TBD Deleted this item.
Version 0.4,11/29 8 TrR + TfF = 5 msec (typ.) TrR + TfF = 25 msec (typ.)
Version 0.4,11/29 11 LED Current TYP 30mA LED Current TYP 120mA Max 150mA
Version 0.4,11/29 28
Version 1.0, 1/4 6 No definition for max Raising Time
Packing Boxˍʳ ʳ 9 pcs/Box Packing Boxˍʳ ʳ 8 pcs/Box
)=25, Falling
rR
), Falling Time (TrF), and Raising +
(T
rR
Falling
Max Raising Time (T
Time (T
)=15, Raising + Falling=40
rF
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
document version 1.0 3
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M270HW02 V0
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the LED lightbar edge. Instead, press at the
far ends of the LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
13) Please avoid touching COF position while you are doing mechanical design.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
document version 1.0 4
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M270HW02 V0
2.0 General Description
This specification applies to the 27 inch-FHD Color a-Si TFT-LCD Module M270HW02. The
display supports the FHD - 1920(H) x 1080(V) screen format and 16.7M colors (RGB 8-bits). The
light source of this TFT-LCD module is W-LED. All input signals are 2-channel LVDS interface and
this module doesn’t contain a driver for backlight.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25к condition:
ITEMS Unit SPECIFICATIONS
Screen Diagonal [mm] 685.65(27.0”)
Active Area [mm] 597.6 (H) x 336.15 (V)
Pixels H x V 1920(x3) x 1080
Pixel Pitch [um] 311.25 (per one triad) ×311.25
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode VA Mode, Normally Black
White Luminance ( Center ) [cd/m2]
300 cd/m
Contrast Ratio 3000(Typ.)
Optical Response Time [msec] 25ms (Typ., on/off)
Nominal Input Voltage VDD [Volt] +5.0 V (Typ)
Power Consumption
(VDD line + LED line)
[Watt] 29.1W (Typ.)
(without inverter, all white pattern)
Weight [Grams] ˅ˊˈ˃ Typ.
Physical Size [mm] 630.0(H)x368.2(V)x11.5(D)
Electrical Interface Dual channel LVDS
Support Color 16.7M colors (RGB 8-bit )
Surface Treatment Anti-Glare, 3H
Temperature Range
Operating
Storage (Shipping)
o
[
C]
o
[
C]
0 to +50
-20 to +60
RoHS Compliance RoHS Compliance
TCO Compiance TCO 5.1 Compiance
2
(Typ.)
document version 1.0 5
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25к:
Item Unit Conditions Min. Typ. Max. Note
Horizontal (Right)
CR = 10 (Left)
Viewing Angle [degree]
Vertical (Up)
CR = 10 (Down)
Contrast ratio Normal Direction
Raising Time (TrR)
Response Time [msec]
Falling Time (TrF)
Raising + Falling
150 178
150 178
2400 3000 -
- 18 25
- 7 15
- 25 40
M270HW02 V0
-
-
2
-
-
3
4
Color / Chromaticity
Coordinates (CIE)
Color Coordinates (CIE) White
Central Luminance [cd/m2]
Luminance Uniformity
Crosstalk (in 60Hz)
Flicker
[%]
[%]
dB
Red x
Red y
Green x
Green y
Blue x
Blue y
White x
White y
0.612 0.642 0.672
0.305 0.335 0.365
0.297 0.327 0.357
0.593 0.623 0.653
0.120 0.150 0.180
0.022 0.052 0.082
0.283 0.313 0.343
0.299 0.329 0.359
240 300 -
75 80 -
1.5
-20
5
6
7
8
9
document version 1.0 6
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M270HW02 V0
Note 1: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt
temperature change during measuring (at surface 35 )к . In order to stabilize the luminance, the
measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and
dark room. ʳ
Photo detector
Measured distance
-
Center of the screen
Note 2: Definition of viewing angle measured by ELDIM (EZContrast 88)
Viewing angle is the measurement of contrast ratio Њ10, at the screen center, over a 180°
horizontal and 180° vertical range (off-normal view ing angles). The 180° viewing angle range is
broken down as follows; 90° ( θ) horizontal left and right and 90° ( Φ) vertical, high (up) and low
(down). The measurement direction is typically perpendicular to the display surface with the
screen rotated about its center to develop the desired measurement viewing angle.
document version 1.0 7
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M270HW02 V0
Note 3: Contrast ratio is measured by TOPCON SR-3
Note 4: Definition of Response time measured by Westar TRD-100A
The output signals of photo detector are measured when the input signals are changed from “Full
Black” to “Full White” (rising time, Tr
), and from “Full White” to “Full Black” (falling time, TfF),
R
respectively. The response time is interval between the 10% and 90% (1 frame at 60 Hz) of
amplitudes.
%
Optical
Optical
response
response
100
100
90
10
10
%
W hite Black
0
0
Tr
Tr
F
F
Black
1 Frame 1 Frame
Tr
Tr
R
R
White
Tr
+ TfF = 25 msec (typ.).
R
Algorithm:ɀGray Level A – Gray Level BɀЊ16, then the average gray to gray response time is 2
ms,(F= 60 Hz).
Note 5: Color chromaticity and coordinates (CIE) is measured by TOPCON SR-3
Note 6: Central luminance is measured by TOPCON SR-3
Note 7: Luminance uniformity of these 9 points is defined as below and measured by
TOPCON SR-3
Uniformity =
9)-(1 points 9in LuminanceMinimum
9)-(1 Points 9in LuminanceMaximum
document version 1.0 8
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
l
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
Note 8: Crosstalk is defined as below and measured by TOPCON SR-3
CT = | YB – YA | / YA 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
M270HW02 V0
Note 9: Test Patern: Subchecker Pattern measured by TOPCON SR-3
RG BRGB
Gray Level = L127
R GBRGB
RGBRGB
Gray Level = L0
Method: Record dBV & DC value with TRD-100
Amplitude
DC
log20(dB)Flicker =
AC
Leve
DC
Time
Hz) 30Level(at AC
document version 1.0 9
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...