Page 1
Product Specification
Preliminary Specification
( )
(V ) Final Specification
Module 27” Color TFT-LCD
Model Name M27HW01 V2 open cell
AU OPTRONICS CORPORATION
M270HW01 V2
Customer Date
Approved by
Approved by Date
Howard Lee
Prepared by Date
EvelynPHSung
Sep 3, 2013
Sep 3, 2013
Note: This Specification is subject to
change without notice.
document version 1.0 1
AU Optronics corporation
Page 2
Product Specification
AU OPTRONICS CORPORATION
M270HW01 V2
Contents
1 Handling Precautions................................................................4
2 General Description ..................................................................5
2.1 Display Characteristics....................................................................................................... 5
2.2 Absolute Maximum Rating of Environment ........................................................................ 6
2.3 Optical Characteristics ....................................................................................................... 7
3 TFT-LCD Module ......................................................................10
3.1 Block Diagram.................................................................................................................. 10
3.2 Interface Connection........................................................................................................ 11
3.2.1 Connector Type............................................................................................................. 11
3.2.2 Connector Pin Assignment............................................................................................ 11
3.3 Electrical Characteristics.................................................................................................. 13
3.3.1 Absolute Maximum Rating ............................................................................................ 13
3.3.2 Recommended Operating Condition............................................................................. 13
3.4 Signal Characteristics ...................................................................................................... 14
3.4.1 LCD Pixel Format.......................................................................................................... 14
3.4.2 LVDS Data Format........................................................................................................ 14
3.4.3 Color versus Input Data ................................................................................................ 15
3.4.4 LVDS Specification........................................................................................................ 16
3.4.5 Input Timing Specification ............................................................................................. 18
3.4.6 Input Timing Diagram.................................................................................................... 19
3.5 Power ON/OFF Sequence ............................................................................................... 20
4 Reliability Test........................................................................21
5 Shipping Label ........................................................................22
6 Mechanical Characteristic .......................................................23
document version 1.0 2
Page 3
Product Specification
AU OPTRONICS CORPORATION
M270HW01 V2
Record of Revision
Version
0.0 2013/9/03
Date Page Old description New Description Remark
All First version release -
document version 1.0 3
Page 4
Product Specification
AU OPTRONICS CORPORATION
M270HW01 V2
1 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
3) When the cell surface is soiled, wipe it with absorbent cotton or other soft cloth.
4) Since the cell is made of glass, it may break or crack if dropped or bumped on hard surface.
5) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
6) Do not press or pat the panel surface by fingers, hand or tooling.
7) Please handle TFT cell with care. The FPCs can only sustain for quite limited stress.
8) The cell package tray is packed in clean room. Please do pack & unpack it in clean room.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT cell.
10) Pls avoid touching COF position while you are doing mechanical design.
11) When storing modules as spares for a long time, the following precaution is necessary:
Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep
the temperature between 5℃ and 35℃ at normal humidity.
document version 1.0 4
Page 5
Product Specification
AU OPTRONICS CORPORATION
M270HW01 V2
2 General Description
This specification applies to the 27 inch wide Color a-Si TFT-LCD Module M270HW01 V2. The
display supports the Full HD - 1920(H) x 1080(V) screen format and 16.7M colors (RGB 6-bits +
Hi-FRC data). The input interface is Dual channel LVDS.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25℃ condition:
ITEMS Unit SPECIFICATIONS
Screen Diagonal [mm] 685.65(27”)
Active Area [mm] 597.6 (H) x 336.15 (V)
Pixels H x V - 1920(x3) x 1080
Pixel Pitch [um] 311.25 (per one triad) ×311.25
Pixel Arrangement - R.G.B. Vertical Stripe
Display Mode - TN Mode, Normally White
Response Time [msec] 5ms (Typ., on/off)
Power Consumption [Watt] 3.5W
Weight [Grams] 768
Electrical Interface - Dual channel LVDS
Support Color - 16.7M colors (RGB 6-bit + Hi-FRC )
Surface Treatment - Anti-Glare, 3H
Temperature Range
Operating
Storage (Shipping)
[oC]
Cell transmittance [%]
0 to +50
-20 to +60
5.1(Typ.)
4.6(Min.)
Base on AUO LED Backlight
Cell thickness [mm] 2.0 (Thickness of polarizer film: 0.31 mm each side)
document version 1.0 5
Page 6
Product Specification
AU OPTRONICS CORPORATION
M270HW01 V2
2.2 Absolute Maximum Rating of Environment
Permanent damage may occur if exceeding the following maximum rating.
Symbol Description Min. Max. Unit Remark
TOP Operating Temperature 0 +50 [oC] Note 2-1
TGS
Glass surface temperature
(operation)
0 +65 [oC]
Function judged only
HOP Operation Humidity 5 90 [%RH]
TST Storage Temperature -20 +60 [oC]
HST Storage Humidity
5 90
[%RH]
Note 2-1: Temperature and relative humidity range are shown as the below figure.
1. 90% RH Max ( Ta ≦39℃)
2. Max wet-bulb temperature at 39℃ or less. ( Ta ≦39℃)
3. No condensation
Note 2-1
Note 2-1
Operating Range Storage Range
document version 1.0 6
Page 7
Product Specification
AU OPTRONICS CORPORATION
2.3 Optical Characteristics
The optical characteristics are measured on the following test condition.
Test Condition:
1. Equipment setup: Please refer to Note 2-2.
2. Panel Lighting time: 30 minutes
3. VDD=5.0V, Fv=60Hz,Is=65mA,Ta=25℃
M270HW01 V2
Symbol Description Min. Typ. Max. Unit Remark
TR Rising Time
TF Falling Time
Response
Time
-
CT Crosstalk - -
FdB Flicker (Center of screen) - -
Note 2-2: Equipment setup :
-
3.5 7.4
-
1.5 2.6
Rising +
-
5 10
Falling
1.5
-20
Photo detector (SR-3, TRD-100)
[msec
]
[%]
[dB]
Note 2-3
By
TRD-100
Note 2-4
By SR-3
Note 2-5
By SR-3
Measured distance (50cm)
Center of the screen
document version 1.0 7
Page 8
Product Specification
100
90
W hite
100
White
Black
Black
1 Frame
1 Frame
AU OPTRONICS CORPORATION
Note 2-3: Response time measurement
The output signals of photo detector are measured when the input signals are changed
from “Black” to “White” (rising time, TR), and from “White” to “Black” (falling time, TF),
respectively. The response time is interval between the 10% and 90% of optical
response. (Black & White color definition: Please refer section 3.4.3)
Optical
Optical
respon se
respon se
10
10
%
%
0
0
T
M270HW01 V2
T
F
R
Note 2-4: Crosstalk measurement
Definition:
CT = Max. (CTH,CTV);
Where
a.Maximum Horizontal Crosstalk :
CTH = Max. (| YBL – YAL | / YAL × 100 %, | YBR – YAR | / YAR × 100 %);
Maximum Vertical Crosstalk:
CTV = Max. (| YBU – YAU | / YAU × 100 %, | YBD – YAD | / YAD × 100 %);
b. YAU, YAD, YAL, YAR = Luminance of measured location without Black pattern
YBU, YBD, YBL, YBR = Luminance of measured location with Black pattern
document version 1.0 8
Page 9
Note 2-5: Flicker measurement
a. Test pattern: It is listed as following.
Product Specification
AU OPTRONICS CORPORATION
Gray level = L0
Gray level = L127
M270HW01 V2
R: Red, G: Green, B:Blue
b. Measured position: Center of screen & perpendicular to the screen
document version 1.0 9
Page 10
Product Specification
Backlight
DC
Connector
LVDS
AU OPTRONICS CORPORATION
M270HW01 V2
3 TFT-LCD Module
3.1 Block Diagram
The following diagram shows the functional block of the 27.0 inch Color TFT-LCD Module:
AUO
ASIC
LVDS
Receiver
+5V
DC/DC
Converter
Gamma
Correction
I/F + X-PCB
Timing
Controller
miniLVDS
Transmitter
G1080
G1
TFT-LCD
1920(x3) x 1080
Pixels
D1
D5760
LED
I/F PCB Interface:
LED Driver on system
JAE-FI-XPB30SRLAHF11
STM- MSCK2407P30
Mating Type:
FI-X30HL(Locked Type)
document version 1.0 10
Page 11
Product Specification
1 RxOIN0
- Negative LVDS differential data input (Odd data)
1
2 RxOIN0+
Positive LVDS differential data input (Odd data)
2
3 RxOIN1
- Negative LVD
S differential data input (Odd data)
3
4 RxOIN1+
Positive LVDS differential data input (Odd data)
4
5 RxOIN2
- Negative LVDS differential data input (Odd data,
5
6 RxOIN2+
Positive LVDS differential data input (Odd data, DSPTMG)
6
7 GND
Power Gr
ound
7
8 RxOCLK
- Negative LVDS differential clock input (Odd clock)
8
9 RxOCLK+
Positive LVDS differential clock input (Odd clock)
9
10 RxOIN3
- Negative LVDS differential data input (Odd data)
10
11 RxOIN3+
Positive LVDS differential data input (Odd da
ta) 11
12 RxEIN0
- Negative LVDS differential data input (Even data)
12
13 RxEIN0+
Positive LVDS differential data input (Even data)
13
14 GND
Power Ground
14
15 RxEIN1
- Positive LVDS differential data input (Even data)
15
16 RxEIN1+
Negative LVDS diff
erential data input (Even data)
16
17 GND
Power Ground
17
18 RxEIN2
- Negative LVDS differential data input (Even data)
18
19 RxEIN2+
Positive LVDS differential data input (Even data)
19
20 RxECLK
- Negative LVDS differential clock input (Even clock)
20
21 RxECLK+
Positive LVDS differential clock input (Even clock)
21
22 RxEIN3
- Negative LVDS differential data input (Even data)
22
23 RxEIN3+
Positive LVDS differential data input (Even data)
23
24 GND
Power Ground
24
25 NC No connection (for AUO test
only. Do not connect)
25
26 NC No connection (for AUO test only. Do not connect)
26
AU OPTRONICS CORPORATION
3.2 Interface Connection
3.2.1 Connector Type
TFT-LCD Connector
Mating Connector
3.2.2 Connector Pin Assignment
Manufacturer JAE STM
Part Number
Manufacturer JAE
Part Number FI-X30HL (Locked Type)
FI-XPB30SRLAHF11
M270HW01 V2
MSCK2407P30
FI-X30HL (Locked Type)
PIN # Symbol Description Remark
document version 1.0 11
Page 12
Product Specification
27 NC No connection (for AUO test only. Do not connect)
27
28 VDD
Power +5V
28
29 VDD
Power +5V
29
30 VDD
Power +5V
30
AU OPTRONICS CORPORATION
M270HW01 V2
document version 1.0 12
Page 13
Product Specification
AU OPTRONICS CORPORATION
3.3 Electrical Characteristics
3.3.1 Absolute Maximum Rating
Permanent damage may occur if exceeding the following maximum rating.
M270HW01 V2
Symbol
VDD
Description Min Max Unit
Power Supply
Input Voltage
GND-0.3 6.0 [Volt]
3.3.2 Recommended Operating Condition
Symbol
VDD
IDD
PDD
IRush Inrush Current
VDDrp
Description Min Typ Max Unit
Power supply
Input voltage
Power supply
Input Current
(RMS)
VDD Power
Consumption
Allowable VDD
Ripple Voltage
4.5
-
-
-
-
5.0
0.7 1
0.8 1.1
3.5 5
4 5.5
- 3
- 500
5.5
[Volt]
[A]
[A]
[Watt]
[Watt]
[A]
[mV]
Remark
Ta=25℃
Remark
VDD= 5.0V, Black Pattern, Fv=60Hz
VDD= 5.0V, Black Pattern, Fv=75Hz
VDD= 5.0V, Black Pattern, Fv=60Hz
VDD= 5.0V, Black Pattern, Fv=75Hz
Note 3-1
VDD= 5.0V, Black Pattern, Fv=75Hz
Note 3-1: Inrush Current measurement:
Test circuit:
document version 1.0 13
Page 14
Product Specification
R G B R G B
R G B R G B
R G B R G B
R G B R G B
1 2 1
919 1
920
1st Line
1080
Line
M270HW01 V2
AU OPTRONICS CORPORATION
3.4 Signal Characteristics
3.4.1 LCD Pixel Format
The duration of VDD rising time: 470us.
3.4.2 LVDS Data Format
Note 3-2:
a. O = “Odd Pixel Data” E = “Even Pixel Data”
b. Refer to 3.4.1 LCD pixel format, the 1st data is 1 (Odd Pixel Data), the 2
nd
data is 2 (Even Pixel Data) and
the last data is 1920 (Even Pixel Data).
document version 1.0 14
Page 15
Product Specification
M270HW01 V2
AU OPTRONICS CORPORATION
3.4.3 Color versus Input Data
The following table is for color versus input data (8bit). The higher the gray level, the brighter
the color.
document version 1.0 15
Page 16
3.4.4 LVDS Specification
Product Specification
AU OPTRONICS CORPORATION
M270HW01 V2
a. DC Characteristics:
Symbol
VTH
VTL
│VID│
VCM
Description Min Typ Max Units
LVDS Differential
Input High Threshold
LVDS Differential
Input Low Threshold
LVDS Differential
Input Voltage
LVDS Common Mode
Voltage
-100 - -
100 - 600
+1.0 +1.2 +1.5
LVDS Signal Waveform:
Use RxOCLK- & RxOCLK+ as example.
RxOCLK-
- - +100
Condition
[mV] VCM = 1.2V
[mV] VCM = 1.2V
[mV]
[V] VTH-VTL = 200mV
RxOCLK+
document version 1.0 16
Page 17
Product Specification
Freq
F
max
F
clk
F
min
F
clk
* F
DEV
< Spread Spectrum>
T
ime
AU OPTRONICS CORPORATION
b. AC Characteristics:
Symbol Description Min Max Unit Remark
Maximum deviation of
F
DEV
input clock frequency
during Spread Spectrum
Maximum modulation
F
MOD
frequency of input clock
during Spread Spectrum
- ± 3 %
- 200 KHz
M270HW01 V2
Fclk: LVDS Clock Frequency
F
1
MOD
document version 1.0 17
Page 18
Product Specification
AU OPTRONICS CORPORATION
3.4.5 Input Timing Specification
It only support DE mode, and the input timing are shown as the following table.
M270HW01 V2
Symbol Description Min. Typ. Max. Unit
Remark
Tv Period 1088 1130 2047 Th
Tdisp (v) Active 1080 1080 1080 Th
Vertical Section
Tblk (v) Blanking 8 50 967 Th
Fv
Frequency
50 60 76
Hz
Th Period 1000 1050 2047 Tclk
Tdisp (h) Active 960 960 960 Tclk
Horizontal Section
Tblk (h) Blanking 40 90 1087 Tclk
Fh
Tclk Period 25 13.3 11.1
Frequency 55 68 91 KHz
ns 1/Fclk
Note 3-3
LVDS Clock
Fclk
Frequency 40 75 90 MHz
Note 3-4
Note 3-3: The equation is listed as following. Please don’t exceed the above recommended value.
Fh (Min.) = Fclk (Min.) / Th (Min.);
Fh (Typ.) = Fclk (Typ.) / Th (Typ.);
Fh (Max.)= Fclk (Max.) / Th (Min.);
Note 3-4: The equation is listed as following. Please don’t exceed the above recommended value.
Fclk (Min.) = Fv (Min.) x Th (Min.) x Tv (Min.);
Fclk (Typ.) = Fv (Typ.) x Th (Typ.) x Tv (Typ.);
Fclk (Max.) = Fv (Max.) x Th (Typ.) x Tv (Typ.);
document version 1.0 18
Page 19
3.4.6 Input Timing Diagram
DE
RGB Data
CLK
DE
RGB Data
(Odd)
RGB Data
(Even)
N
Line
Pixel
M-7
Pixel
M-6
Pixel
M-5
Pixel
Pixel
M-3
Pixel
M-2
Tblk(v)
Invalid Data
Tclk
Pixel
M-1
Pixel
M
Invalid Data
Invalid Data
Product Specification
AU OPTRONICS CORPORATION
Tv
Tdisp(v)
Th
32
LineLine
Th
Tdisp(h)
Pixel
Pixel
10
4
LineLine
Pixel
Pixel
119
Pixel
12
1
Pixel
1
Pixel Pixel
2
Pixel
Pixel
3
4
Pixel
7
5
Pixel
Pixel
6 M-2
8 M
N
Line
M-5
M-4
Pixel
M-3
Pixel
M270HW01 V2
Invalid Data
Tblk(h)
Pixel
M-1
PixelPixel
Invalid Data
Invalid Data
N Line
M pixel
Y
X
Pixel
Pixel
1
3
Pixel
Pixel
4
2M-4
document version 1.0 19
Page 20
Product Specification
10%
90%
10%
90%
AU OPTRONICS CORPORATION
M270HW01 V2
3.5 Power ON/OFF Sequence
VDD power,LVDS signal and backlight on/off sequence are as following. LVDS signals
from any system shall be Hi-Z state when VDD is off.
T1
VDD
LVDS Signal
T2
T3
VALID
T4
T5
T6
T7
Backlight Enable
Signal (system)
Backlight Off
Power Sequence Timing
Backlight On
Backlight Off
Value Remark
Symbol
T1
T2
T3
T4
T5
T6
T7
Min. Typ. Max.
0.5 10 0.5
0 50 0
500 - 500
200 - 200
40 - 40
1000 - 1000
0.5 10 0.5
Unit
[ms]
[ms]
[ms]
[ms]
[ms]
[ms]
[ms]
Note 3-5
Note 3-6
Note 3-6
Note 3-5 : Recommend setting T5 = 0ms to avoid electronic noise when VDD is off.
Note 3-6 : During T5 and T6 period , please keep the level of input LVDS signals with Hi-Z state.
document version 1.0 20
Page 21
KV, 150pF(330Ω ) 1sec,
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
4 Reliability Test
Product Specification
AU OPTRONICS CORPORATION
M270HW01 V2
AUO reliability test items are listed as following table. (Bare Panel only)
Items Condition
Temperature Humidity Bias (THB)
High Temperature Operation (HTO)
Low Temperature Operation (LTO)
High Temperature Storage (HTS)
Low Temperature Storage (LTS)
Vibration Test
(Non-operation)
Shock Test
(Non-operation)
Drop Test Height: 60 cm, package test
Ta= 50℃, 80%RH, 300hours
Ta= 50℃, 50%RH, 300hours
Ta= 0℃, 300hours
Ta= 60℃, 300hours
Ta= -20℃, 300hours
Acceleration: 1.5 Grms
Wave: Random
Frequency: 10 - 200 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)
Acceleration: 50 G
Wave: Half-sine
Active Time: 20 ms
Direction: ±X, ±Y, ±Z (one time for each Axis)
Remark
Thermal Shock Test (TST)
On/Off Test On/10sec, Off/10sec, 30,000 cycles
-20℃/30min, 60℃/30min, 100 cycles
Note 4-1
Contact Discharge: ± 15
8 points, 25 times/ point.
ESD (Electro Static Discharge)
Note 4-2
8 points, 25 times/ point.
Altitude Test
Operation:18,000 ft
Non-Operation:40,000 ft
Note 4-1: a. A cycle of rapid temperature change consists of varying the temperature from -20 to ℃
60 , and back again. Power is not applied during the test. ℃
b. After finish temperature cycling, the unit is placed in normal room ambient for at least
4 hours before power on.
Note 4-2: EN61000-4-2, ESD class B: Certain performance degradation allowed
No data lost
Self-recoverable
No hardware failures.
document version 1.0 21
Page 22
Product Specification
AU OPTRONICS CORPORATION
5 Shipping Label
5.1 Small Shipping Label
The label is on the PCBA as shown below :
XXXXXXXXXXXX–XXXXXX XXXX M270HW01 V2.X
5.2 Run Card Label
The label is on the panel as shown below :
M270HW01 V2
M270HW01-x/xx xx:xxxxxxxxxx Remark : X
0
S/N xxxxxxxxxxxx (xxxxx)
xxxxx xxxxx xxxxx
xxxxx xxxxx xxxxx
xxxxx xxxxx xxxxx
xxxxx xxxxx xxxxx
Z P N V
SKD
document version 1.0 22
Page 23
6 Mechanical Characteristic
Ver 1.0
Loading...