Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
( V ) Preliminary Specification
( ) Final Specification
Module 24” WUXGA Color TFT-LCD
Model Name M240UP01 V0 Open Cell
Customer Date
Approved by
Checked &
Approved by
Prepared by
Allen KC Huang Feb. 18, 2008
Date
Note: This Specification is subject to change without
notice.
document version 1.1
Desktop Display Business Unit /
AU Optronics corporation
1/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
Contents
1. Handling Precautions ..................................................................................................................4
2. General Description..................................................................................................................... 5
2.1 Display Characteristics ........................................................................................................................ 5
3. Functional Block Diagram...........................................................................................................9
4. Absolute Maximum Ratings...................................................................................................... 10
4.1 Absolute Ratings of TFT LCD Module ............................................................................................. 10
4.2 Absolute Ratings of Backlight Unit ................................................................................................... 10
4.3 Absolute Ratings of Environment ...................................................................................................... 10
5. Electrical characteristics .......................................................................................................... 11
5.1 TFT LCD Module ............................................................................................................................. 11
6. Signal Characteristic .................................................................................................................12
6.1 Pixel Format Image ........................................................................................................................... 12
6.2 Signal Description .............................................................................................................................13
6.3 The input data format......................................................................................................................... 16
6.4 Signal Electrical Characteristics ........................................................................................................ 18
6.5 Interface Timings............................................................................................................................... 21
6.6 Power ON/OFF Sequence................................................................................................................. 23
7. Connector & Pin Assignment ...................................................................................................24
7.1 TFT LCD Module ............................................................................................................................. 24
8. Reliability Test............................................................................................................................ 27
9. Shipping Label............................................................................................................................28
10. Mechanical Characteristics ....................................................................................................29
document version 1.1
2/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
Record of Revision
Version & Date Page Old Description New Description Remark
document version 1.1
3/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not press the or pat the panel surface by fingers, hand or tooling.
8) Please handle TFT cell with care. The FPCs can only sustain for quite limited stress.
9) The cell package tray is packed in clean room. Please do pack & unpack it in clean room.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of TFT cell.
document version 1.1
4/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
2. General Description
This specification applies to the 24 inch-wide Color TFT-LCD open cell M240UP01 v.0. The screen format is
intended to support the WUXGA (1920(H) x 1200(V)) screen and 16.7M colors (RGB 6-bits + Hi-FRC data).
The input signals are VESA standard analog RGB and DVI-D interface compatible.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 к condition:
Items Unit Specifications
Active Area [mm] 518.4(H) × 324(V)
Pixels H x V 1920 × 3(RGB) × 1200
Pixel Pitch [mm] 0.270(per one triad) × 0.270
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode, Normally White
Optical ResponseTime [msec] 5 ms(Typ)
Nominal Input Voltage VCC [Volt] +5.0 (Typ)
Power Consumption
(VCC line)
Weight [Grams] 804.7 (Typ)
[Watt] 8(Typ)
Electrical Interface
VESA standard Analog RGB ;
DVI-D ( HDCP1.1)
Surface Treatment Anti-glare type, Harness 3H
Support Color 16.7M colors (RGB 6-bits + HiFRC data)
Plug & Play VESA DDC2B/2Bi/2B+/CI 2
Compability PC/MAC
Max. Firmware Code Size [byte] 64K+32K
Max. Pixel Clock [MHz] 165 MHz
Auto Adjustment Auto Color, Size & Phase 2
RoHS Compliance RoHS Compliance
1
With AUO standard firmware
2
With AUO standard power module & firmware
document version 1.1
5/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25к (Room Temperature):
Item Unit Conditions Min. Typ. Max. Note
Rising - 3.8 6.1
Falling - 1.2 1.9
Optical Response Time [msec]
Rising + Falling - 5 8
Grey to Grey (avg.) - 2 -
1, 3
Cross Talk (At 75Hz) [%] - - 1.5
2
Flicker [dB] - - -20 4
Optical Equipment: BM-5A, BM-7, PR880, or equivalent
document version 1.1
6/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
Note 1: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be executed after
lighting Backlight for 30 minutes in a stable, windless and dark room. ʳ
Photo detector
Field=2
50 cm
Note 2: Definition of Cross Talk (CT)
CT = | YB – YA | / YA Ø 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
LCD Panel
Center of the screen
TFT-LCD Module
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
document version 1.1
7/29
Product Specification
L
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
Note 3: Definition of response time:
The output signals of photo detector are measured when the input signals are changed from “Full Black” to
“Full White” (rising time), and from “Full White” to “Full Black ”(falling time), respectively. The response time
is interval between the 10% and 90% of amplitudes. Please refer to the figure as below.
Note 4: Subchecker Pattern
RGBRGB
Gray Level = L127
R GBRGB
RGBRGB
Method: Record dBV & DC value with (WESTAR)TRD-100
Amplitude
DC
Gray Level = L0
AC
Time
log20(dB)Flicker =
Hz) 30Level(at AC
evel DC
document version 1.1
8/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
3. Functional Block Diagram
The following diagram shows the functional block of the 24.0 inches wide Color TFT-LCD Module:
document version 1.1
9/29
Product Specification
V
4. Absolute Maximum Ratings
Absolute maximum ratings of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min. Max. Unit Conditions
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
Logic/LCD Drive
VCC -0.3 +5.25 [Volt] Note 1, 2
oltage
4.2 Absolute Ratings of Backlight Unit
Item Symbol Min. Max. Unit Conditions
CCFL Current ICFL 0 8.0 [mA] rms Note 1, 2
4.3 Absolute Ratings of Environment
Item Symbol Min. Max. Unit Conditions
Operating Temperature TOP 0 +50 [oC]
Operation Humidity HOP 5 90 [%RH]
Storage Temperature TST -20 +60 [oC]
Storage Humidity HST
5 90
[%RH]
Note 1: With in Ta= 25к
Note 3
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
Operating Range Storage Range
document version 1.1
10/29
Product Specification
V
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows:
Symble Parameter Min. Typ. Max. Unit Condition
VCC
Logic/LCD Drive
Voltage
4.75 5.0 5.25 [Volt] Load Capacitance 20uF
ICC Input Current - 1.6 2.4 [A] VCC= 5.0V, All Black Pattern
PCC VCC Power - 8.0 12 [Watt]
VCCrp
Allowable
Logic/LCD Drive
Ripple Voltage
- - 100
[mV]
p-p
Note 1,
VCC= 5.0
, All Black Pattern
PS Power Saving - 0.3 0.5 [Watt] VCC= 5.0V
Note 1: The variance of VCC power consumption is ±10%.
document version 1.1
11/29
Product Specification
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
AU OPTRONICS CORPORATION
1 2 1919 1920
M240UP01 V0 open cell
1st Line
1200th Line
R G B R G B
R G B R G B
R G B R G B
R G B R G B
document version 1.1
12/29
Product Specification
6.2 Signal Description
Power / OSD Connector (J1)
PIN# Signal Name Description
1 VCC DC 5V
2 BKLT_ADJ Light adjust for the DC/AC inverter(PWM)
3 VCC DC 5V
4 BKLT_EN Enable for the DC/AC inverter
5 VCC DC 5V
6 AUDIO _EN Enable audio power control signal
7 VCC DC 5V
8 MUTE Mute audio
9 GND Ground
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
10 VOLUME Adjust audio volume (PWM)
11 GND Ground
12 Key_Power Power on/off function
13 GND Ground
14 MENU OSD menu on/off function
15 GND Ground
16 PLUS OSD plus selection function
17 S/PDIF Audio control signal
18 MINUS OSD minus selection function
19 I2CSDA I2C SDA
20 DOWN OSD down selection function
21 I2CSCL I2C SCL
22 UP OSD up selection function
23 SD0 Audio data
24 SELECT OSD item select function
25 WS Audio control signal
26 SOURCE OSD item source function
27 SCK Audio control signal
28 LED_A LED Amber for the sleep mode
29 MCK Audio control signal
30 LED_G LED Green for the full mode
document version 1.1
13/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
DVI-D / D-sub Connector (J2)
PIN# Signal Name Description
1 DATA2/4 Shield Shared shield for TMDS link #0 channel #2 and link #1 channel #1
2 GND Ground
3 DATA2+ TMDS link #0 channel #2 differential pair
4 DVI_5V
+5V signal provided by the system to enable the monitor to provide EDID
data when the monitor circuitry is not powered.
5 DATA2- TMDS link #0 channel #2 differential pair
6 HPD
Host Plug Detect ; Signal is driven by monitor to enable the system to
identify the presence of a monitor.
7 GND Ground
8 GND Ground
9 DATA1+ TMDS link #0 channel #1 differential pair
10 DDC Data The clock line for the DDC interface
11 DATA1- TMDS link #0 channel #1 differential pair
12 DDC Clock The data line for the DDC interface
13 DATA1/3 Shield Shared shield for TMDS link #0 channel #1 and link #1 channel #0
14 GND Ground
15 DATA0+ TMDS link #0 channel #0 differential pair
16 VCC DC 5V
17 DATA0- TMDS link #0 channel #0 differential pair
18 HDMI_HDP 2D reserved I/O
19 DATA0/5 Shield Shared shield for TMDS link #0 channel #0 and link #1 channel #2
20 2D_SW 2D reserved I/O
21 Clock+ TMDS clock differential pair
22 DVI_CONN 2D reserved I/O
23 Clock- TMDS clock differential pair
24 GND Ground
25 Clock Shield Shield for TMDS clock differential pair
26 VSync Vertical synchronization signal for the analog interface
27 B_GND Ground for the analog blue signal
28 HSync Horizontial synchronization signal for the analog interface
29 BIN Analog Blue signal
30 GND Ground
31 G_GND Ground for the analog green signal
32 SDA The data line for the DDC interface
33 GIN Analog Green signal
document version 1.1
14/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
34 SCL The clock line for the DDC interface
35 R_GND Ground for the analog red signal
36 PC_5V
+5V signal provided by the system to enable the monitor to provide EDID
37 RIN Analog Red signal
38 VGA_CON Video cable connected detect signal (host connect this pin to ground)
39 GND Ground
40 GND Ground
Note 1: For DVI-D cable part:
a. DVI differential pairs (DATA-/+) impedance 100+/-10 Ohm.
b. DVI differential pairs (DATA-/+) should twist wire.
Note 2: For D-sub cable part:
a. R/G/B impedance 75+/-10 Ohm
document version 1.1
15/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
6.3 The input data format
The input data format is followed the VESA Vedio Signal Standard. In each RGB termination is described as
following table.
Values
Max Luminance Voltage Input Data = (FFh) 0.700 Volts +0.070 /-0.035 volts
Min Luminance voltage Input Data = (00h) 0.000 Volts
Video Channel Rise/Fall Time Max 25% of minimum pixel clock period
Maximum Settling Time after
overshoot/undershoot
30% of minimum pixel clock period averaged over 100
waveforms to 5% final full-scale value.
Monotonic Yes
Resolution 1 LSB
Integral Linearity Error
Differential Linearity Errorʳ
1 LSB
1 LSB
Video Channel to Video Channel Mismatch 6% of any video output voltage over the full voltage range
Video Noise injection ratio
2.5 % of Max Luminance Voltage
Video Channel to Video Channel Output Skew 50% of minimum pixel clock period
Overshoot/Undershoot
12% of step function voltage level over the full voltage
range
document version 1.1
16/29
Product Specification
The Synchronization (Hsync and Vsync) Signal format is described as following table.
Driver Logic Level “1” 2.4 Volts 5.5 Volts
Driver Logic Level “0” 0.0 Volts 0.5 Vots
Driver High Level Output Current 8mA
Driver Low Level Output Current 8mA
Receiver Logic Level “1” 2.0 Volts
Receiver Logic Level “0” 0.8 Volts
Fall Time Max 80% of minimum pixel clock period
Rise Time Max 80% of minimum pixel clock period
Monotonic Rise/Fall Voltage range 0.5-2.4 Volts
AU OPTRONICS CORPORATION
Min. Max.
M240UP01 V0 open cell
Overshoot/Undershoot
Jitter
(Measured between Hsync pulses)
30% of high level signal voltage range No signal
excursions allowed in the 0.5-2.4 volt voltage range
Over the frequency spectrum: One half of the
difference between the maximum and minimum
interval between Hsync pulses measured over
100,000 intervals shall be less than 15% of the pixel
clock, 0Hz to max. horizontal refresh rate at all image
formats, worst-case screen patterns.
LSB : Least Significant Bit
Monotonic
1. The property of either never increasing or never decreasing in reference to the slope of a
transient response.
2. A constant slope value containing no inflection points.
Sync: Synchronization Signals
For more details, please refer to VESA (Video Electronics Standards Association) Video Signal
Standard.
document version 1.1
17/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
6.4 Signal Electrical Characteristics
Power / OSD interface (J1)
Pin# Name Type Min. Typ. Max. Unit Remark
1 VCC 4.75 5.0 5.25 V
2 BKLT_ADJ
High (Max.) VCC V
Low (Min.) 0.3 V
Internal serial 2.2K Ohm
Internal serial 3.2K Ohm
3 VCC 4.75 5.0 5.25 V
4 BKLT_EN
High (On) VCC V
Low (Off) 0.3 V
Internal serial 10K Ohm
5 VCC 4.75 5.0 5.25 V
6 AUDIO _EN
High (On) 2.65 3.3 V -4mA
Low (Off) GND 0.45 V 5mA
7 VCC 4.75 5.0 5.25 V
8 MUTE
High (On) 2.65 3.3 V -4mA
Low (Off) GND 0.45 V 5mA
9 GND
10 VOLUME
High (Max.) 3.2 V
Low (Min.) 0.1 V 4mA
11 GND
12 Key_Power Active 0 V
13 GND
14 MENU Active 0 V
15 GND
16 PLUS Active 0 V
17
18
19
20
21
22
23
24
25
26
27
28
29
30
S/PDIF
MINUS
I2CSDA
DOWN
I2CSCL
UP
SD0
SELECT
WS
SOURCE
SCK
LED_A
MCK
LED_G
Active 0 V
Active 0 V
Active 0 V
Active 0 V
Active 0 V
LED Amber for
the sleep mode
3.1 V Internal serial 68 Ohm
LED Green for
the full mode
3.1 V Internal serial 68 Ohm
document version 1.1
18/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
DVI-D / D-sub interface (J2)
Pin# Name Type Min. Typ. Max. Unit
1 DATA2/4 Shield
2 GND
3 DATA2+
4 DVI_5V
5 DATA2-
6 HPD
7 GND
8 GND
9 DATA1+
10 DDC Data
11 DATA1-
12 DDC Clock
13 DATA1/3 Shield
14 GND
15 DATA0+
16 VCC
17 DATA0-
18 HDMI_HDP
19 DATA0/5 Shield
20 2D_SW
21 Clock+
22 DVI CONN
23 Clock-
24 GND
25 Clock Shield
26 VSync
27 B_GND
28 HSync
29 BIN 700 mV
30 GND
31 G_GND
32 SDA
33 GIN 700 mV
34 SCL
35 R_GND
36 PC_5V
High 2.0 5.0 V
Low GND 0.8 V
High 2.0 5.0 V
Low GND 0.8 V
High 2.0 5.0 V
Low GND 0.8 V
High 2.0 5.0 V
Low GND 0.8 V
document version 1.1
19/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
37 RIN 700 mV
38 VGA_CON
39 GND
40 GND
document version 1.1
20/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
6.5 Interface Timings
The signal interface of the TFT-LCD module is analog RGB compatible.
6.5.1 Timing Characteristics
The timings are supported by the signal interface of M240UP01 are listed as following table.
Resolution
Horizontal
Frequency
(KHz)
Vertical
Frequency
(Hz)
Dot Clock
(MHz)
Actually Display
Resolution
Remark
640x350 31.47(P) 70.08(N) 25.17 1920 x1200 DOS
720x400 31.47(N) 70.08(P) 28.32 1920 x1200 DOS
640x480 31.47(N) 60.00(N) 25.18 1920 x1200 DOS
640x480 35.00(N) 67.00(N) 30.24 1920 x1200 Macintosh
640x480 37.86(N) 72.80(N) 31.5 1920 x1200 VESA
640x480 37.50(N) 75.00(N) 31.5 1920 x1200 VESA
800x600 37.88(P) 60.32(P) 40 1920 x1200 VESA
800x600 48.08(P) 72.19(P) 50 1920 x1200 VESA
800x600 46.86(P) 75.00(P) 49.5 1920 x1200 VESA
832X624 49.72(N) 74.55(N) 57.29 1920 x1200 Macintosh
1024x768 48.36(N) 60.00(N) 65 1920 x1200 VESA
1024x768 56.48(N) 70.10(N) 75 1920 x1200 VESA
1024x768 60.02(P) 75.00(P) 78.75 1920 x1200 VESA
1024X768 60.24(N) 74.93(N) 80 1920 x1200 Macintosh
1152x864 67.50(P) 75.00(P) 108 1920 x1200 VESA
1152x870 68.68(N) 75.06(N) 100 1920 x1200 Macintosh
1152x900 61.80(N) 66.00(N) 94.5 1920 x1200 SUN 66
1152x900 71.81(N) 76.14(N) 108 1920 x1200 SUN
1280x1024 64.00(P) 60.00(P) 108 1920 x1200 VESA
1280x1024 75.83(N) 71.53(N) 128 1920 x1200 IBM1
1280x1024 80.00(P) 75.00(P) 135 1920 x1200 VESA
1280x1024 81.18(N) 76.16(N) 135.09 1920 x1200 SPARC2
1680x1050 64.7(P) 59.883(N) 119 1920 x1200 VESA
1680x1050 65.29(N) 59.954(P) 146.25 1920 x1200 VESA
1920x1200 74.04(P) 60(N) 154 1920 x1200 VESA
1920x1200 74.56(N) 60(P) 193.25 1920 x1200 VESA
Note-1: Depend on firmware setting. For D-sub, It can support other resolution when Dot Clock <210MHZ.
And DVI for Dot Clock <165MHZ
Note-2: “P”, “N” stands for “Positive”, “Negative” polarity of incoming H-sync/V-sync (input timing)
document version 1.1
21/29
6.5.2 Definition of terms
Video Signal Definition
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
a) Vmin steady state Amplitude before transition
b) Video Rise Time Delta (t), (measured from the 10% to 90% points of Vmin Steady State to Vmax Steady
State)
c) Overshoot Amplitude
d) Undefined
e) Settling Time - Measured from the end of the overshoot to the point where the amplitude of the video
ringing is down to 5% of the final steady state value
f) Undefined
g) Video Fall Time Delta (t), (measured from the 90% to 10% points of Vmax Steady State to Vmin Steady
State)
h) Undefined here, Note: Undershoot is within this period and with an Amplitude of (j)
i) Settling Time - Measured from the end of the undershoot to the point where the amplitude of the video
ringing is down to 5% of the final steady state value
j) Vmin steady state Amplitude after transition
Synchronization Signal Definition
document version 1.1
22/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
6.6 Power ON/OFF Sequence
VCC power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals
from any system shall be Hi-Z state or low level when VCC is off.
90%
90%
Power Supply VCC
Input Signal
Backlight On
Parameter
10%
T1
T2
VALID
DATA
T3
T4
Power Sequence Timing
Value
Min. Typ. Max.
T5
T6
T7
T8
10%
Unit
10%
T9
T1 - - 10 [ms]
T2 10 - 50 [ms]
T3
(Black pattern only)
30 - 50 [ms]
T4 200 - - [ms]
T5 200 - - [ms]
T6
(White pattern only)
50 - 100 [ms]
T7 0 16 50 [ms]
T8 - - 100 [ms]
T9 1000 - - [ms]
document version 1.1
23/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
7. Connector & Pin Assignment
Physical interface is described as for the connector on module.These connectors are capable of
accommodating the following signals and will be following components
.
7.1 TFT LCD Module
7.1.1 Connector
Connector Name / Designation Power / OSD Connector / J1
Manufacturer STM or compatiable
Type / Part Number STM-MDS240315A
Mating Housing / Part Number STM-PD240315
Connector Name / Designation DVI-D / D-sub Connector / J2
Manufacturer STM or compatiable
Type / Part Number STM-MDS240320A
Mating Housing / Part Number STM-PD24320-2
document version 1.1
24/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
7.1.2 Pin Assignment
Power / OSD Connector (J1)
Pin# Signal Name Pin# Signal Name
1 VCC 2 BKLT_ADJ
3 VCC 4 BKLT_EN
5 VCC 6 AUDIO _EN
7 VCC 8 MUTE
9 GND 10 VOLUME
11 GND 12 Key_Power
13 GND 14 MENU
15 GND 16 PLUS
17 S/PDIF 18 MINUS
19 I2CSDA 20 DOWN
21 I2CSCL 22 UP
23 SD0 24 SELECT
25 WS 26 SOURCE
27 SCK 28 LED_A
29 MCK 30 LED_G
document version 1.1
25/29
Product Specification
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
DVI-D / D-sub Connector (J2)
Pin# Signal Name Pin# Signal Name
1 DATA2/4 Shield 2 GND
3 DATA2+ 4 DVI_5V
5 DATA2- 6 HPD
7 GND 8 GND
9 DATA1+ 10 DDC Data
11 DATA1- 12 DDC Clock
13 DATA1/3 Shield 14 GND
15 DATA0+ 16 VCC
17 DATA0- 18 HDMI_HDP
19 DATA0/5 Shield 20 2D_SW
21 Clock+ 22 DVI_CONN
23 Clock- 24 GND
25 Clock Shield 26 VSync
27 B_GND 28 HSync
29 BIN 30 GND
31 G_GND 32 SDA
33 GIN 34 SCL
35 R_GND 36 PC_5V
37 RIN 38 VGA_CON
39 GND 40 GND
document version 1.1
26/29
Product Specification
8. Reliability Test
Environment test conditions are listed as following table.
Items Required Condition
Temperature Humidity Bias (THB) Ta= 5
High Temperature Operation (HTO) Ta= 5
Low Temperature Operation (LTO) Ta=
High Temperature Storage (HTS) Ta=
Low Temperature Storage (LTS) Ta= -
Vibration Test
(Non-operation)
AU OPTRONICS CORPORATION
80%RH, 300hours
50%RH, 300hours
Acceleration: 1.5 G
Wave: Random
Frequency: 10 - 200 - 10 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)
M240UP01 V0 open cell
Note
Acceleration: 50 G
Shock Test
(Non-operation)
Wave: Half-sine
Active Time: 20 ms
Direction: X,ʳY,ʳZ (one time for each Axis)
Drop Test Height: 38 cm, package test
Thermal Shock Test (TST) -20/30min, 60/30min, 100 cycles
On/Off Test On/10sec, Off/10sec, 30,000 cycles
1
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec,
8 points, 25 times/ point.
ESD (ElectroStatic Discharge)
2
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
8 points, 25 times/ point.
Altitude Test
Operation:10,000 ft
Non-Operation:30,000 ft
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-2˃к to 6˃к, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.
document version 1.1
27/29
Product Specification
9. Shipping Label
The shipping label format is shown as below.
AU OPTRONICS CORPORATION
M240UP01 V0 open cell
document version 1.1
28/29
M240UP01 V0 open cell
AU OPTRONICS CORPORATION
Product Specification
10. Mechanical Characteristics
document version 1.1 29/29
Loading...