ASUS PTGD1-LA PUFFER M-UL8E User Manual

Page 1
PTGD1-LA
(Puffer M-UL8E)
Motherboard
Page 2
Checklist
Contents
PTGD1-LA specifications summary ..................................................... iii
1. Motherboard layout ................................................................. 1
3. System memory ...................................................................... 5
4. Expansion slots ........................................................................ 8
5. Jumpers ................................................................................. 10
6. Connectors ............................................................................ 11
6.1 Rear panel connectors ............................................. 11
6.2 Internal connectors .................................................. 13
ii
Page 3
PTGD1-LA specifications summary
CPUCPU
CPU
CPUCPU
ChipsetChipset
Chipset
ChipsetChipset
Front Side Bus (FSB)Front Side Bus (FSB)
Front Side Bus (FSB)
Front Side Bus (FSB)Front Side Bus (FSB)
MemoryMemory
Memory
MemoryMemory
Expansion slotsExpansion slots
Expansion slots
Expansion slotsExpansion slots
Rear panelRear panel
Rear panel
Rear panelRear panel
LGA775 socket for the Intel® Pentium® 4 processor
®
Nortbridge: Intel
(MCH)
Southbridge: Intel® ICH6
800 MHz
4 x 184-pin DDR DIMM sockets for up to 4 GB
non-ECC DDR SDRAM
1 x PCI Express x16 slot for discrete graphics card 3 x PCI slots
1 x PS/2 mouse port 1 x PS/2 keyboard port 1 x Parallel port 1 x IEEE 1394a port 1 x LAN (RJ-45) port 6 x audio ports support 8-channel audio configuration 4 x USB 2.0 ports support hot-plug function 1 x S/PDIF Out port 1 x S/PDIF In port
915P Memory Controller Hub
Internal connectorsInternal connectors
Internal connectors
Internal connectorsInternal connectors
StorageStorage
Storage
StorageStorage
1 x Floppy connector 1 x IDE connector 1 x 24-pin ATX power connector 1 x 4-pin ATX 12 V power connector 4 x Serial ATA connectors 1 x IEEE 1394a connector 2 x USB 2.0 connectors 1 x CPU fan connector 1 x System fan connector 2 x Internal audio connectors 1 x Front headphone connector 1 x System panel connector
Southbridge supports:
- 2 x Ultra DMA 66/100 hard disk drives
- 4 x Serial ATA (SATA) ports with hot-swap function
(continued on the next page)
iiiiii
iii
iiiiii
Page 4
PTGD1-LA specifications summary
AudioAudio
Audio
AudioAudio
Southbridge supports 8-channel audio configuration
with Intel® High Definition Audio CODEC
Realtek® ALC880 High Definition Audio CODEC
LANLAN
LAN
LANLAN
IEEE 1394IEEE 1394
IEEE 1394
IEEE 1394IEEE 1394
PC healthPC health
PC health
PC healthPC health monitoringmonitoring
monitoring
monitoringmonitoring
BIOS featuresBIOS features
BIOS features
BIOS featuresBIOS features
Form factorForm factor
Form factor
Form factorForm factor
* Specifications are subject to change without notice
Realtek
VIA VT6307 supports two IEEE 1394a ports
ASUS A8000 for CPU, system, and chassis fan
4Mb FWH EEPROM HP BIOS with enhanced ACPI, DMI, Green, and PnP
Micro-ATX form factor: 9.6 in x 9.6 in
®
RTL8101L 10/100Mbps Fast Ethernet
LAN controller
control, motherboard and CPU temperature
Features Plus
iviv
iv
iviv
Page 5
1. Motherboard layout
24.5cm (9.6in)
PS/2KBMS T: Mouse B: Keyboard
Bottom: T:USB1 B:USB2
USB2.0 T: USB3 B: USB4
AUDIO
Top:Line In
Center:Line Out
Below:Mic In
ALC880
CD_IN
PARALLEL PORT
Top: 1394
Top: RJ-45
RTL8101L
F_LINE_IN
SYS_FAN
FRONT_AUDIO
ATX12V
Top:
Subwoofer Speaker Out
Center
Rear Speaker Out
Below
CPU_FAN
Side Speaker Out
PTGD1-LA
PCIEX16
PCI1
PCI2
PCI3
Intel
915P
MCH
VT6307
IEEE
Controller
FRONT_1394
4Mbit Flash ROM
ASUS A8000
FLOPPY
DDR DIMMA2 (64 bit,184-pin module)
DDR DIMMA1 (64 bit,184-pin module)
DDR DIMMB2 (64 bit,184-pin module)
DDR DIMMB1 (64 bit,184-pin module)
ATX Power Connector
Intel
ICH6
CLRTC
FRONT_USB1
SATA 3
SATA 1
FRONT_USB2
BAT_H
SATA 4
SATA 2
BUZZ1
FRONT_PANEL
CLPWD
IDE
24.5cm (9.6in)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
11
1
11
Page 6
2. Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA775 socket designed for the Intel
®
Pentium® 4 processor in the 775-land package.
Your boxed Intel® Pentium® 4 LGA775 processor package should come with installation instructions for the CPU, heatsink, and the retention mechanism. If the instructions in this section do not match the CPU documentation, follow the latter.
Upon purchase of the motherboard, make sure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/ transit-related.
Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA775 socket.
The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap.
Installing the CPUInstalling the CPU
Installing the CPU
Installing the CPUInstalling the CPU
To install a CPU:
1. Locate the CPU socket on the motherboard.
PTGD-LA
PTGD1-LA CPU Socket 775
Before installing the CPU, make sure that the socket box is facing towards you and the load lever is on your left.
22
2
22
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Page 7
2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab.
Retention tabRetention tab
Retention tab
Retention tabRetention tab
A
PnP capPnP cap
PnP cap
Load leverLoad lever
Load lever
Load leverLoad lever
PnP capPnP cap
To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU.
3. Lift the load lever in the direction of the arrow to a 135º angle.
4. Lift the load plate with your thumb and forefinger to a 100º angle (A), then push the PnP cap from the load plate window to remove (B).
B
This side of theThis side of the
This side of the
This side of theThis side of the socket box shouldsocket box should
socket box should
socket box shouldsocket box should face you.face you.
face you.
face you.face you.
B
A
5. Position the CPU over
the socket, making sure that the gold triangle is on the bottom-left corner of the socket. The
Alignment keyAlignment key
Alignment key
socket alignment key
Alignment keyAlignment key
should fit into the CPU notch.
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Gold triangle markGold triangle mark
Gold triangle mark
Gold triangle markGold triangle mark
Load plateLoad plate
Load plate
Load plateLoad plate
33
3
33
Page 8
6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab.
The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU!
A
B
Notes on IntelNotes on Intel
Notes on Intel
Notes on IntelNotes on Intel
This motherboard supports Intel® Pentium® 4 CPUs in the 775-land
Hyper-Threading Technology is supported under Windows
Installing Windows
Make sure to enable the Hyper-Threading Technology item in BIOS
For more information on Hyper-Threading Technology, visit
®
Hyper-Threading Technology Hyper-Threading Technology
Hyper-Threading Technology
Hyper-Threading Technology Hyper-Threading Technology
package with Hyper-Threading Technology.
®
XP/2003 Server and Linux 2.4.x (kernel) and later versions only. Under Linux, use the Hyper-Threading compiler to compile the code. If you are using any other operating systems, disable the Hyper-Threading Techonology item in the BIOS to ensure system stability and performance.
®
XP Service Pack 1 or later version is recommended.
before installing a supported operating system.
www.intel.com/info/hyperthreading.
To use the Hyper-Threading Technology on this motherboard:
®
1. Install an Intel
Pentium® 4 CPU that supports Hyper-Threading
Technology.
2. Power up the system and enter the BIOS Setup. Under the Advanced Menu, make sure that the item Hyper-Threading Technology is set to Enabled. The item appears only if you installed a CPU that supports Hyper-Threading Techonology.
3. Reboot the computer.
44
4
44
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Page 9
3. System memory
The motherboard comes with four Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets.
The following figure illustrates the location of the DDR DIMM sockets.
DIMM_B2
PTGD-LA
DIMM_A1
DIMM_B1
DIMM_A2
PTGD1-LA 184-pin DDR DIMM sockets
Memory configurationsMemory configurations
Memory configurations
Memory configurationsMemory configurations
You can install 128 MB, 256 MB, 512 MB, and 1GB DDR SDRAM DIMMs into the DIMM sockets using the memory configurations in this section.
Installing DDR DIMMs other than the recommended configurations may cause memory sizing error or system boot failure. Use any of the recommended configurations on the next page.
Install only
identical identical
identical (the same type and size) DDR DIMM pairs
identical identical
using the recommended configurations.
Make sure that the memory frequency matches the CPU FSB (Front Side Bus). Refer to the Memory frequency/CPU FSB synchronization table on the next page.
This motherboard does not support double-sided 16-bit DDR DIMMs.
Do not create a three-DIMM configuration in dual-channel mode. The third DIMM is ignored in the dual-channel operation.
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
55
5
55
Page 10
Recommended memory configurationsRecommended memory configurations
Recommended memory configurations
Recommended memory configurationsRecommended memory configurations
ModeMode
Mode
ModeMode
Single-channel (1) Installed
(2) Installed — (3) Installed — (4) Installed
Dual-channel* (1) Installed Installed
(2) Installed Installed (3) Installed Installed Installed Installed
* Use only identical DDR DIMM pairs.* Use only identical DDR DIMM pairs.
* Use only identical DDR DIMM pairs.
* Use only identical DDR DIMM pairs.* Use only identical DDR DIMM pairs.
Memory frequency/CPU FSB synchronizationMemory frequency/CPU FSB synchronization
Memory frequency/CPU FSB synchronization
Memory frequency/CPU FSB synchronizationMemory frequency/CPU FSB synchronization
CPU FSBCPU FSB
CPU FSB
CPU FSBCPU FSB
800 MHz PC3200 400 MHz 533 MHz PC3200/PC2700 400/333 MHz
DIMM1DIMM1
DIMM1
DIMM1DIMM1
DDR DIMM TypeDDR DIMM Type
DDR DIMM Type
DDR DIMM TypeDDR DIMM Type
SocketsSockets
Sockets
SocketsSockets
DIMM2DIMM2
DIMM2
DIMM2DIMM2
DIMM3DIMM3
DIMM3
DIMM3DIMM3
Memory FrequencyMemory Frequency
Memory Frequency
Memory FrequencyMemory Frequency
DIMM4DIMM4
DIMM4
DIMM4DIMM4
66
6
66
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Page 11
3.23.2
3.2
3.23.2
Installing a DDR DIMMInstalling a DDR DIMM
Installing a DDR DIMM
Installing a DDR DIMMInstalling a DDR DIMM
Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components.
To install a DIMM:
1. Unlock a DIMM socket by pressing the retaining clips outward.
2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket.
2
DDR DIMM notchDDR DIMM notch
DDR DIMM notch
DDR DIMM notchDDR DIMM notch
1
1
Unlocked retaining clipUnlocked retaining clip
Unlocked retaining clip
Unlocked retaining clipUnlocked retaining clip
A DDR DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into a socket to avoid damaging the DIMM.
3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated.
3.33.3
3.3
3.33.3
Removing a DDR DIMMRemoving a DDR DIMM
Removing a DDR DIMM
Removing a DDR DIMMRemoving a DDR DIMM
To remove a DIMM:
1. Simultaneously press the retaining clips outward to unlock the DIMM.
Locked Retaining ClipLocked Retaining Clip
Locked Retaining Clip
Locked Retaining ClipLocked Retaining Clip
2
1
1
Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force.
2. Remove the DIMM from the socket.
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
DDR DIMM notchDDR DIMM notch
DDR DIMM notch
DDR DIMM notchDDR DIMM notch
77
7
77
Page 12
4. Expansion slots
The motherboard has one PCI Express and three PCI slots.
To install and configure an expansion card:
1. Install an expansion card following the instructions that came with the chassis.
2. Turn on the system and change the necessary BIOS settings, if any.
3. Assign an IRQ to the card. Refer to the tables below.
4. Install the drivers and/or software applications for the expansion card according to the card documentation.
Standard interrupt assignmentsStandard interrupt assignments
Standard interrupt assignments
Standard interrupt assignmentsStandard interrupt assignments
IRQIRQ
IRQ
IRQIRQ
0 System Timer 1 Standard 101/102-key or Microsoft® Natural PS/2 Keyboard 2 Programmable Interrupt Controller 3 AHPC IRQ Holder for PCI IRQ Steering 3 Intel® 82801FB/FBM PCI Express Root Port-2660 3 Intel® 82801FB/FBM USB Universal Host Controller-265B 3 Intel® i915P MCH 5 AHPC IRQ Holder for PCI IRQ Steering 5 AHPC IRQ Holder for PCI IRQ Steering 5 Realtek® TRL8139/810x Family Fast Ethernet NIC 5 Intel® 82801FB/FBM PCI Express Root Port-2662 5 Intel® 82801FB/FBM USB Universal Host Controller-2658 5 Intel® 82801FB/FBM USB2 Enhanced Host Controller-265C 6 Standard Floppy Disk Controller 7 ECP Printer Port (LPT1) 8 System CMOS/Real Time Clock 9 SCI IRQ used by ACPI Bus 10 AHPC IRQ Holder for PCI IRQ Steering 10 AHPC IRQ Holder for PCI IRQ Steering 10 VIA OHCI Compliant IEEE 1394 Host Controller 10 Intel® 82801FB/FBM PCI Express Root Port-2666 10 Intel® 82801FB/FBM Ultra ATA Storage Controllers-2659 11 AHPC IRQ Holder for PCI IRQ Steering 11 Intel® 82801FB/FBM PCI Express Root Port-2664 11 Intel® 82801FB/FBM USB Universal Host Controller-265A 12 Microsoft® Port Mouse 13 Numeric Data Processor 14 Intel® 82801FB/FBM Ultra ATA Storage Controllers-266F 14 Intel
Standard FunctionStandard Function
Standard Function
Standard FunctionStandard Function
®
82801FB Ultra ATA Storage Controllers-2652
88
8
88
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Page 13
IRQ assignments for this motherboardIRQ assignments for this motherboard
IRQ assignments for this motherboard
IRQ assignments for this motherboardIRQ assignments for this motherboard
AB CDE F
PCI slot 1 shared — PCI slot 2 shared — PCI slot 3 used — Onboard LAN used Onboard 1394 controller used
PCI Express slotPCI Express slot
PCI Express slot
PCI Express slotPCI Express slot
This motherboard has one PCI Express slot, which supports a 164-pin x16 interface graphics card.
PCI slotsPCI slots
PCI slots
PCI slotsPCI slots
There are three 32-bit PCI slots on this motherboard. The slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications.
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
99
9
99
Page 14
5. Jumpers
Clear RTC RAM (3-pin CLRTC)Clear RTC RAM (3-pin CLRTC)
Clear RTC RAM (3-pin CLRTC)
Clear RTC RAM (3-pin CLRTC)Clear RTC RAM (3-pin CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 2-3 (Normal) to pins 1-2 (Clear
CMOS). Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 2-3.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS
setup to re-enter data.
Except when clearing the RTC RAM, never remove the cap from the default position. Removing the cap will cause system boot failure!
CLRTC
PTGD-LA
PTGD1-LA Clear RTC RAM
Clear password (3-pin CLPWD)Clear password (3-pin CLPWD)
Clear password (3-pin CLPWD)
Clear password (3-pin CLPWD)Clear password (3-pin CLPWD)
12 23
Normal Clear CMOS
(Default)
This jumper allows you to clear the password if you forgot your password.
CLPWD
3 2 1
Clear Password
PTGD-LA
2
Normal
(Default)
1010
10
1010
PTGD1-LA Clear password setting
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Page 15
6. Connectors
6.16.1
6.1
6.16.1
1
15
1.1.
PS/2 mouse port (green).PS/2 mouse port (green).
1.
PS/2 mouse port (green). This port is for a PS/2 mouse.
1.1.
PS/2 mouse port (green).PS/2 mouse port (green).
2.2.
Parallel port.Parallel port.
2.
Parallel port. This 25-pin port connects a parallel printer, a scanner,
2.2.
Parallel port.Parallel port. or other devices.
3.3.
IEEE 1394a port.IEEE 1394a port.
3.
IEEE 1394a port. This 6-pin IEEE 1394a port provides high-speed
3.3.
IEEE 1394a port.IEEE 1394a port. connectivity for audio/video devices, storage peripherals, PCs, or portable devices.
Rear panel connectorsRear panel connectors
Rear panel connectors
Rear panel connectorsRear panel connectors
2 43
1314
12
5 6 7
8
9
10
11
4.4.
LAN (RJ-45) port.LAN (RJ-45) port.
4.
LAN (RJ-45) port. This port allows connection to a Local Area
4.4.
LAN (RJ-45) port.LAN (RJ-45) port. Network (LAN) through a network hub.
5.5.
Side Speaker Out port (gray).Side Speaker Out port (gray).
5.
Side Speaker Out port (gray). This port connects to the side
5.5.
Side Speaker Out port (gray).Side Speaker Out port (gray). speakers in an 8-channel audio configuration.
6.6.
Rear Speaker Out port (black).Rear Speaker Out port (black).
6.
Rear Speaker Out port (black). This port connects to the rear
6.6.
Rear Speaker Out port (black).Rear Speaker Out port (black). speakers on a 4-channel, 6-channel, or 8-channel audio configuration.
7.7.
Center/Subwoofer port (yellow orange).Center/Subwoofer port (yellow orange).
7.
Center/Subwoofer port (yellow orange). This port connects
7.7.
Center/Subwoofer port (yellow orange).Center/Subwoofer port (yellow orange). the center/subwoofer speakers.
8.8.
Line In port (light blue).Line In port (light blue).
8.
Line In port (light blue). This port connects a tape, CD, DVD
8.8.
Line In port (light blue).Line In port (light blue). player or other audio sources.
Line Out port (lime).Line Out port (lime).
9.9.
Line Out port (lime). This port connects a headphone or a
9.
Line Out port (lime).
9.9.
Line Out port (lime). speaker. In 4-channel, 6-channel, and 8-channel mode, the function of this port becomes Front Speaker Out.
10.10.
Microphone port (pink). Microphone port (pink).
10.
Microphone port (pink). This port connects a microphone.
10.10.
Microphone port (pink). Microphone port (pink).
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
1111
11
1111
Page 16
Audio 2, 4, 6, or 8-channel configurationAudio 2, 4, 6, or 8-channel configuration
Audio 2, 4, 6, or 8-channel configuration
Audio 2, 4, 6, or 8-channel configurationAudio 2, 4, 6, or 8-channel configuration
Headset/Headset/
Headset/
Headset/Headset/
2-channel2-channel
2-channel
2-channel2-channel
Light Blue Line In Line In Line In Line In
Lime Line Out Front Speaker Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Mic In Mic In
Yellow Orange - - Center/Subwoofer Center/Subwoofer
Black - Rear Speaker Out Rear Speaker Out Rear Speaker Out
Gray - - - Side Speaker Out
11.11.
USB 2.0 ports 3 and 4.USB 2.0 ports 3 and 4.
11.
USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus
11.11.
USB 2.0 ports 3 and 4.USB 2.0 ports 3 and 4.
4-channel4-channel
4-channel
4-channel4-channel
6-channel6-channel
6-channel
6-channel6-channel
8-channel8-channel
8-channel
8-channel8-channel
(USB) ports are available for connecting USB 2.0 devices.
12.12.
USB 2.0 ports 1 and 2.USB 2.0 ports 1 and 2.
12.
USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus
12.12.
USB 2.0 ports 1 and 2.USB 2.0 ports 1 and 2. (USB) ports are available for connecting USB 2.0 devices.
13.13.
Coaxial S/PDIF Out port. Coaxial S/PDIF Out port.
13.
Coaxial S/PDIF Out port. This port connects an external audio
13.13.
Coaxial S/PDIF Out port. Coaxial S/PDIF Out port. output device via a coaxial S/PDIF cable.
14.14.
Coaxial S/PDIF In port. Coaxial S/PDIF In port.
14.
Coaxial S/PDIF In port. This port connects an external audio input
14.14.
Coaxial S/PDIF In port. Coaxial S/PDIF In port. device via a coaxial S/PDIF cable.
15.15.
PS/2 keyboard port (purple).PS/2 keyboard port (purple).
15.
PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
15.15.
PS/2 keyboard port (purple).PS/2 keyboard port (purple).
1212
12
1212
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Page 17
6.26.2
6.2
6.26.2
Internal connectorsInternal connectors
Internal connectors
Internal connectorsInternal connectors
This section describes and illustrates the internal connectors on the motherboard.
1.1.
Floppy disk drive connector (34-1 pin FLOPPY)Floppy disk drive connector (34-1 pin FLOPPY)
1.
Floppy disk drive connector (34-1 pin FLOPPY)
1.1.
Floppy disk drive connector (34-1 pin FLOPPY)Floppy disk drive connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After
connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug).
Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5.
PIN 1
FLOPPY
NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
PTGD-LA
PTGD1-LA Floppy disk drive connector
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
1313
13
1313
Page 18
2.2.
IDE connector (40-1 pin IDE)IDE connector (40-1 pin IDE)
2.
IDE connector (40-1 pin IDE)
2.2.
IDE connector (40-1 pin IDE)IDE connector (40-1 pin IDE) This connector is for an Ultra DMA 100/66 signal cable. The Ultra DMA
100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66 IDE master device (hard disk drive). If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings.
Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable.
Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
PTGD-LA
PTGD1-LA IDE connector
NOTE: Orient the red markings
(usually zigzag) on the IDE ribbon cable to PIN 1.
IDE
PIN 1
1414
14
1414
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Page 19
3.3.
ATX power connectors (24-pin ATXPWR, 4-pin ATX12V)ATX power connectors (24-pin ATXPWR, 4-pin ATX12V)
3.
ATX power connectors (24-pin ATXPWR, 4-pin ATX12V)
3.3.
ATX power connectors (24-pin ATXPWR, 4-pin ATX12V)ATX power connectors (24-pin ATXPWR, 4-pin ATX12V)
These connectors are for an ATX power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.
Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up.
Make sure that your ATX 12V power supply can provide 8A on the +12V lead and at least 1A on the +5-volt standby lead (+5VSB). The minimum recommended wattage is 230W, or 300W for a fully configured system. The system can become unstable and might experience difficulty powering up if the power supply is inadequate.
You must install a PSU with a higher power rating if you intend to install additional devices.
ATXPWR
PTGD-LA
PTGD1-LA ATX power connectors
+3 Volts +12 Volts +12 Volts
+5V Standby
Power OK
Ground
+5 Volts
Ground
+5 Volts
Ground +3 Volts +3 Volts
Ground +5 Volts +5 Volts +5 Volts
-5 Volts Ground Ground Ground PSON# Ground
-12 Volts +3 Volts
ATX12V
+12V DCGND
+12V DCGND
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
1515
15
1515
Page 20
4.4.
SS
4.
4.4.
erial ATA connectorserial ATA connectors
S
erial ATA connectors
SS
erial ATA connectorserial ATA connectors
(7-pin SATA1, S(7-pin SATA1, S
(7-pin SATA1, S
(7-pin SATA1, S(7-pin SATA1, S
ATA2, SATA3, SATA4)ATA2, SATA3, SATA4)
ATA2, SATA3, SATA4)
ATA2, SATA3, SATA4)ATA2, SATA3, SATA4)
These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives.
SATA1 SATA2 SATA3 SATA4
PTGD-LA
GND
GND
GND
PTGD1-LA SATA connectors
Important notes on Serial ATAImportant notes on Serial ATA
Important notes on Serial ATA
Important notes on Serial ATAImportant notes on Serial ATA
RSATA_TXP1
RSATA_TXN1
RSATA_RXP1
RSATA_RXN1
Install the Windows® 2000 Service Pack 4 or the Windows® XP Service Pack1 before using Serial ATA.
SS
When using the connectors in
tandard IDE tandard IDE
S
tandard IDE mode, connect the
SS
tandard IDE tandard IDE
primary (boot) hard disk drive to the SATA1 connector.
1616
16
1616
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Page 21
5.5.
IEEE 1394a connector (10-1 pin FRONT_1394)IEEE 1394a connector (10-1 pin FRONT_1394)
5.
IEEE 1394a connector (10-1 pin FRONT_1394)
5.5.
IEEE 1394a connector (10-1 pin FRONT_1394)IEEE 1394a connector (10-1 pin FRONT_1394) This connector is for an IEEE 1394a port. Connect the IEEE 1394a
module cable to this connector, then install the module to a slot opening at the back of the system chassis.
PTGD-LA
+12V
TPB+
GND
TPA+
1
FRONT_1394
PTGD1-LA Front_1394 connector
NEVER connect a
USB cable USB cable
USB cable to the IEEE 1394a connector. Doing so
USB cable USB cable
GND
+12V
GND
TPB-
TPA-
will damage the motherboard!
6.6.
USB connectors (10-1 pin FRONT_USB1, FRONT_USB2)USB connectors (10-1 pin FRONT_USB1, FRONT_USB2)
6.
USB connectors (10-1 pin FRONT_USB1, FRONT_USB2)
6.6.
USB connectors (10-1 pin FRONT_USB1, FRONT_USB2)USB connectors (10-1 pin FRONT_USB1, FRONT_USB2) These connectors are for USB 2.0 ports. Connect the USB/GAME
module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed.
PTGD-LA
PTGD1-LA USB 2.0 connectors
Never connect a
1394 cable1394 cable
1394 cable to the USB connectors. Doing so will
1394 cable1394 cable
damage the motherboard!
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
FRONT_USB1
GND
USB_P5+
USB_P5-
USB+5V
NC
GND
USB+5V
USB_P6-
USB_P6+
FRONT_USB2
GND
USB_P5+
USB_P5-
USB+5V
NC
GND
USB+5V
USB_P6-
USB_P6+
1717
17
1717
Page 22
7.7.
CPU and System fan connectorsCPU and System fan connectors
7.
CPU and System fan connectors
7.7.
CPU and System fan connectorsCPU and System fan connectors (4-pin CPU_FAN, 3-pin SYS_FAN)(4-pin CPU_FAN, 3-pin SYS_FAN)
(4-pin CPU_FAN, 3-pin SYS_FAN)
(4-pin CPU_FAN, 3-pin SYS_FAN)(4-pin CPU_FAN, 3-pin SYS_FAN) The fan connectors support cooling fans of 350 mA ~ 740 mA (8.88
W max.) or a total of 1 A~2.22 A (26.64 W max.) at +12 V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Insufficient air flow within the system can damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors!
CPU_FAN
GND +12V Rotation PWN
SYS_FAN
PTGD-LA
GND +12V Rotation
PTGD1-LA Fan connectors
8.8.
Internal audio connectors (4-pin CD-IN, F_LINE_IN)Internal audio connectors (4-pin CD-IN, F_LINE_IN)
8.
Internal audio connectors (4-pin CD-IN, F_LINE_IN)
8.8.
Internal audio connectors (4-pin CD-IN, F_LINE_IN)Internal audio connectors (4-pin CD-IN, F_LINE_IN) These connectors allow you to receive stereo audio input from sound
sources such as a CD-ROM, TV tuner, or MPEG card.
CD_IN (Black) F_LINE_IN (White)
PTGD-LA
PTGD1-LA Internal audio connectors
Ground
Ground
Right Audio Channel
Left Audio Channel
Ground
Ground
Right Audio Channel
Left Audio Channel
1818
18
1818
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Page 23
9. Front headphone connector (10-1 pin FRONT_AUDIO)9. Front headphone connector (10-1 pin FRONT_AUDIO)
9. Front headphone connector (10-1 pin FRONT_AUDIO)
9. Front headphone connector (10-1 pin FRONT_AUDIO)9. Front headphone connector (10-1 pin FRONT_AUDIO) This connector is for a chassis-mounted front panel headphone port.
AUD_FPOUT_L
AUD_MIC_JD
AUD_FPOUT_R
AUD_MIC2
AUD_MIC1
1
FRONT_AUDIO
PTGD-LA
AUD_VCC
AUD_GND
AUD_RET_R
PTGD1-LA Front headphone & Mic in connector
AUD_RET_L
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
1919
19
1919
Page 24
10.10.
System panel connector (10-1 pin FRONT_PANEL)System panel connector (10-1 pin FRONT_PANEL)
10.
System panel connector (10-1 pin FRONT_PANEL)
10.10.
System panel connector (10-1 pin FRONT_PANEL)System panel connector (10-1 pin FRONT_PANEL) This connector supports several chassis-mounted functions.
HDD LEDReset
HDLED-
Ground
NC
HDLED+
FRONT_PANEL
PTGD-LA
GND Reset
PWR
PLED-
PLED+
Power LEDPower Button
PTGD1-LA Front panel audio connector
System power LEDSystem power LED
System power LED
System power LEDSystem power LED This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
Hard disk drive activityHard disk drive activity
Hard disk drive activity
Hard disk drive activityHard disk drive activity This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The IDE LED lights up or flashes when data is read from or written to the HDD.
Power/Soft-off buttonPower/Soft-off button
Power/Soft-off button
Power/Soft-off buttonPower/Soft-off button This connector is for the system power button. Pressing the power button turns the system ON or puts the system in SLEEP or SOFT-OFF mode depending on the BIOS settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF.
Reset buttonReset button
Reset button
Reset buttonReset button This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power.
2020
20
2020
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)
ASUS PTGD1-LA (Puffer M-UL8E)ASUS PTGD1-LA (Puffer M-UL8E)
Loading...