ASUS PRL-DLS533 User Manual

Page 1
PRL-DLS533
Dual Intel® Xeon™-based Motherboard
E1223
ServerWorks
PRL-DLS533
User Guide
®
GCSL SystemSet
E1223
Page 2
PRL-DLS533
User Guide
Motherboard
Page 3
Checklist
E1223 First Edition
March 2003
Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
ii
Page 4
ASUS Contact Information
ASUSTeK COMPUTER INC. (Asia-Pacific)
Address: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 General Tel: +886-2-2894-3447 General Fax: +886-2-2894-3449 General Email: info@asus.com.tw
Technical Support
MB/Others (Tel): +886-2-2890-7121 (English) Notebook (Tel): +886-2-2890-7122 (English) Desktop/Server (Tel):+886-2-2890-7123 (English) Support Fax: +886-2-2890-7698 Support Email: tsd@asus.com.tw Web Site: www.asus.com.tw
ASUS COMPUTER INTERNATIONAL (America)
Address: 44370 Nobel Drive, Fremont, CA 94538, USA General Fax: +1-510-608-4555 General Email: tmd1@asus.com
Features
Technical Support
Support Fax: +1-510-608-4555 General Support: +1-502-933-8713 Web Site: www.asus.com Support Email: tsd@asus.com
ASUS COMPUTER GmbH (Germany & Austria)
Address: Harkortstr. 25, 40880 Ratingen, BRD, Germany General Fax: +49-2102-442066 General Email: sales@asuscom.de (for marketing requests only)
Technical Support
Support Hotline: MB/Others: +49-2102-9599-0 Notebook (Tel): +49-2102-9599-10 Support Fax: +49-2102-9599-11 Support (Email): www.asuscom.de/de/support (for online support) Web Site: www.asuscom.de
iii
Page 5
Safeguards
Contents
Product introduction
Chapter 1 .................................................................................. 1
1.1 Welcome! .............................................................................. 1
1.2 Package contents.................................................................. 1
1.3 Special features..................................................................... 2
1.3.1 Product highlights ..................................................... 2
1.3.2 Value-added solutions............................................... 4
1.4 Motherboard overview........................................................... 6
1.4.1 Major components .................................................... 6
1.4.2 Core specifications ................................................... 8
Hardware information
Chapter 2 .................................................................................. 1
2.1 Motherboard installation ........................................................ 1
2.1.1 Placement direction .................................................. 1
2.1.2 Screw holes .............................................................. 1
2.2 Motherboard layout ............................................................... 2
2.3 Before you proceed ............................................................... 3
2.4 Central Processing Unit (CPU).............................................. 4
2.4.1 Overview ................................................................... 4
2.4.2 Installing the CPU ..................................................... 5
2.4.3 Installing the CPU heatsink and fan.......................... 6
2.5 System memory .................................................................... 8
2.5.1 Overview ................................................................... 8
2.5.2 Memory Configurations............................................. 9
2.5.3 Installing a DIMM .................................................... 10
2.5.4 Removing a DIMM .................................................. 10
2.6 Expansion slots .................................................................... 11
2.6.1 Installing an expansion card ....................................11
2.6.2 Configuring an expansion card ................................11
2.6.3 PCI slots ................................................................. 13
iv
2.7 Switches and jumpers ......................................................... 14
2.7.1 Switches ................................................................. 14
2.7.2 Jumpers .................................................................. 16
Page 6
Contents
2.8 Connectors .......................................................................... 19
2.9 Onboard LEDs..................................................................... 27
2.9.1 Port 80h post code LEDs ........................................ 28
Powering up
Chapter 3 .................................................................................. 1
3.1 Starting up for the first time ................................................... 1
3.2 Powering off the computer .................................................... 2
BIOS setup
Chapter 4 .................................................................................. 1
4.1 Managing and updating your BIOS ....................................... 1
4.1.1 Creating a bootable disk ........................................... 1
4.1.2 Updating the BIOS .................................................... 3
4.2 BIOS Setup program ............................................................. 5
4.2.1 BIOS menu bar ......................................................... 6
4.2.2 Legend bar................................................................ 6
4.3 Main Menu............................................................................. 8
4.3.1 Primary/Secondary/Tertiary Master/Slave .............. 10
4.3.2 Keyboard Features ................................................. 14
4.4 Advanced Menu .................................................................. 15
4.4.1 Chip Configuration .................................................. 17
4.4.2 I/O Device Configuration......................................... 18
4.4.3 PCI Configuration ................................................... 20
4.5 Power Menu ........................................................................ 22
4.5.1 Power Up Control ................................................... 24
4.5.2 Hardware Monitor ................................................... 26
4.6 Boot Menu ........................................................................... 27
4.6.1 Slot Configuration ................................................... 30
4.7 Server Menu........................................................................ 31
4.7.1 Event Log Viewer.................................................... 32
4.8 Exit Menu ............................................................................ 33
Driver installation
Chapter 5 .................................................................................. 1
v
Page 7
FCC/CDC statements
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
vi
Page 8
Safety information
Electrical safety
To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.
Seek professional assistance before using an adpater or extension cord. These devices could interrupt the grounding circuit.
Make sure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
Operation safety
Before installing the product and adding devices on it, carefully read all the documentation that came with the package.
Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet.
Place the product on a stable surface.
If you encounter technical problems with the product, contact a qualified service technician or your retailer.
vii
Page 9
About this guide
This user guide contains the information you need when installing this ASUS motherboard.
How this guide is organized
This manual contains the following parts:
Chapter 1: Product introduction
This chapter describes the features of this motherboard. It includes brief descriptions of the special attributes of the motherboard and the new technology it supports.
Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the switches, jumpers, and connectors on the motherboard.
Chapter 3: Powering up This chapter describes the power up sequence and gives information
on the BIOS beep codes.
Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter 5: OS Installation
This chapter tells how to install SCSI, LAN, and VGA drivers for various operating systems.
viii
Page 10
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual.
WARNING: Information to prevent injury to yourself when trying to complete a task.
CAUTION: Information to prevent damage to the components when trying to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
Where to find more information
Refer to the following sources for additional information and for product and software updates.
1. ASUS Websites
The ASUS websites worldwide provide updated information on ASUS hardware and software products. The ASUS websites are listed in the ASUS Contact Information on page x.
2. Optional Documentation
Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.
ix
Page 11
PRL-DLS533 specifications summary
CPU
Chipsets
Front Side Bus (FSB) Memory
Onboard LAN
Onboard SCSI Onboard VGA Expansion slots
®
Support for Intel On-die 512KB L2 cache
RCC Grand Champion Super Lite North Bridge (GMIC-SL) RCC Champion South Bridge 6.0 (CSB6) RCC Champion I/O Bridge 2.0 (CIOB-X2)
400 MHz / 533 MHz 4 x 184-pin DDR DIMM sockets
Supports PC2100/PC1600 registered ECC DDR DIMMs Supports 128MB to 4GB system memory
BroadCom 5703C 64bit PCI-X Gigabit Ethernet controller Intel® 82540 32bit PCI Gigabit Ethernet controller
LSI® 53C1030 PCI-X SCSI controller ATI® RAGE-XL PCI-based VGA controller 4 x PCI 64-bit/100MHz 3V (PCI-X1 to PCI-X4)
1 x PCI 64-bit/33MHz 3V (PCI64) (PCI-X3 supports AMI MegaRAID 320-0 or Intel SRU ZCR card) 1 x PCI 32-bit/33MHz 5V (PCI32)
Xeon™ processor
Rear panel I/O
Internal connectors
1 x Parallel port 1 x Serial port 1 x VGA port 1 x PS/2 keyboard port 1 x PS/2 mouse port 2 x USB 1.1 ports 2 x RJ-45 ports (with LED)
2 x 68-pin Ultra-160/320 SCSI connectors 2 x ATA/100 IDE connectors 1 x ATA/66 IDE Connector
1 x Floppy disk connector 1 x Serial Port 2 (COM2) connector eRMC and IPMI connectors (for ASMC card) CPU/Power/Chassis fan connectors 24-pin/8-pin ATX power connectors IDE LED/Power LED connectors 20-pin Front panel connector Chassis intrusion, SMBus, WOL, and WOR connectors
(Continued on the next page)
x
Page 12
PRL-DLS533 specifications summary
BIOS features
Form Factor Support CD contents
* Specifications are subject to change without notice.
4Mb Flash ROM, Award BIOS with ACPI, DMI, Green, PnP features, and Enhanced Server BIOS features
Extended ATX form factor: 12 in x 13 in (30.5 cm x 33 cm) Device drivers
Management software Utilities Contact information
xi
Page 13
Page 14
Chapter 1
This chapter describes the features of the PRL-DLS533 motherboard. It includes brief explanations of the special attributes of the motherboard and the new technology it supports.
Product introduction
Page 15
Chapter summary
1.1 Welcome! ........................................................ 1-1
1.2 Package contents .......................................... 1-1
1.3 Special features ............................................. 1-2
1.4 Motherboard overview................................... 1-6
ASUS PRL-DLS533 motherboard
Page 16
1.1 Welcome!
Thank you for buying the ASUS® PRL-DLS533 motherboard!
The ASUS latest technologies making it another standout in the long line of ASUS quality server motherboards!
The PRL-DLS533 supports dual Intel coupled with the ServerWorks System Set to deliver a reliable and high performance dual-processor server platform.
Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below.
PRL-DLS533 motherboard delivers a host of new features and
®
Xeon™ 604-pin processors
®
Grand Champion Super-Lite (GCSL)
1.2 Package contents
Check your PRL-DLS533 package for the following items.
ASUS PRL-DLS533 motherboard
Extended ATX form factor: 12 in x 13 in (30.5 cm x 33 cm) ASUS PRL-DLS533 support CD I/O shield 80-conductor ribbon cable for UltraDMA100/66//33 IDE drives 68-pin LVD SCSI cable for Ultra 160/320 SCSI devices Ribbon cable for a 3.5-inch floppy drive Bag of extra jumper caps PRL-DLS533 User Guide LSI SCSI Controller User’s Manual
If any of the above items is damaged or missing, contact your retailer.
ASUS PRL-DLS533 motherboard user guide
1-1
Page 17
1.3 Special features
1.3.1 Product highlights
Latest processor technology
The PRL-DLS533 motherboard supports Intel® Xeon™ processors via dual 604-pin surface mount ZIF sockets. The processor features the Intel NetBurst™ micro-architecture that includes hyper-pipelined technology, a rapid execution engine, a 533MHz or a 400MHz system bus, and an execution trace cache to offer a significant increase in performance. See page 2-4 for more information.
DDR memory support
Employing the Double Data Rate (DDR) memory technology, the PRL­DLS533 motherboard supports up to 4GB of system memory using PC2100/1600 registered ECC DDR DIMMs. The ultra-fast 266MHz memory bus doubles the speed of the PC133 SDRAM to deliver the required bandwidth for the latest 3D graphics, multimedia, and Internet applications. See page 2-10.
®
Dual-channel Ultra-320 SCSI
The LSI® 53C1030 64-bit/100MHz PCI-X SCSI controller, is onboard to support dual-channel Ultra-320 SCSI connectors that provide high-speed data transfer interfaces.
Advanced 64-bit PCI-X slots
The 64-bit/100MHz PCI-X slots onboard maximizes I/O bandwidth for the next generation 64-bit PCI-X cards that support 100MHz bus. The PCI-X specification 1.0a allows full peer-to-peer transactions between PCI buses and provides options for intelligent I/O and server management cards.
ATA/100 IDE support
The dual-channel bus master IDE connectors comply with the ATA/100 protocol and supports ATA/100, Multi-Word DMA Mode2, PIO modes 3 & 4 IDE devices such as ATAPI IDE CD-ROM, CD-R/RW, ZIP, and LS-120 drives.
1-2
Chapter 1: Product introduction
Page 18
Third IDE Channel support
The CSB6 South Bridge chip provides a third IDE with PIO mode 3/4 support which provides more device connectivity in this server system.
Onboard LAN
The motherboard comes with the Intel® 82540 Gigabit Ethernet controller and the Broadcom 5703C PCI-X Gigabit Ethernet controller to support the latest LAN technologies.
Onboard VGA
The ATI Rage-XL PCI-based VGA controller integrates an 8MB display SDRAM to provide onboard video solution.
ASUS PRL-DLS533 motherboard user guide
1-3
Page 19
1.3.2 Value-added solutions
Temperature, fan, and voltage monitoring
The CPU temperature is monitored by the ASUS ASIC to prevent overheating and damage. The system fan rotations per minute (RPM) is monitored for timely failure detection. The system voltage levels are monitored to ensure stable supply of current for critical components.
Dual function power switch
While the system is ON, pressing the power switch for less than 4 seconds puts the system to sleep mode or to soft-off mode, depending on the BIOS setting. Pressing the power switch for more than 4 seconds lets the system enter the soft-off mode regardless of the BIOS setting.
Remote Ring In
This feature allows the system to wake up remotely through an internal or external modem, if present.
Wake-Up support
The motherboard includes Wake-On-LAN, Wake-On-Ring, and BIOS Wake-Up features.
Server management
The motherboard comes with an ASMC connector that supports the optional ASMC-HE/ME/LE card to comply with server reliability, availability, and serviceability requirements. Remote management response via remote diagnostics and troubleshooting still works even when the operating system has stopped functioning.
ACPI ready
The Advanced Configuration power Interface (ACPI) provides more energy saving features for operating systems that support OS Direct Power Management (OSPM).
Concurrent PCI
This feature allows multiple PCI transfers from PCI master buses to the memory and processor.
1-4
Chapter 1: Product introduction
Page 20
Chassis intrusion detection
The motherboard supports chassis intrusion monitoring through the ASUS ASIC. A chassis intrusion event is retained in the system memory for more protection.
Smart BIOS
The 4Mbit firmware gives an easy-to-use interface that provides more control and protection to the motherboard. The BIOS has a boot block write protection and HD/SCSI/MO/ZIP/CD/Floppy boot selection, and is Year 2000 certified.
Compliance
Both the BIOS and the hardware levels of the motherboard meet the stringent requirements for SDG 2.0 certification. The new SDG 2.0 requirements for systems and components are based on the following high-level goals: support for Plug-and-Play compatibility and power management for configuring and managing all system components, 32-bit device drivers, and installation procedures for Windows NT/2000/XP. Color-coded connectors and descriptive icons make identification easy as required by the PC ‘99 specification.
ASUS PRL-DLS533 motherboard user guide
1-5
Page 21
1.4 Motherboard overview
Before you install the PRL-DLS533 motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades. A sufficient knowledge of the motherboard specifications will also help you avoid mistakes that may damage the board and its components.
1.4.1 Major components
The following are the major components of the PRL-DLS533 motherboard as pointed out in the picture on page 1-7.
1. 604-pin CPU sockets
®
2. ServerWorks SuperLite (GCSL) North Bridge
3. 8-pin 12V SSI power connector 24/20-pin ATX power connector
4. DIP switches
5. DDR DIMM sockets
6. Floppy disk connector
7. Serverworks CSB6 South Bridge
8. IDE connectors
9. 2 Ultra-160/320 SCSI Connectors
10. LSI-Logic
11. Flash ROM
12. DIP switches
13. ServerWorks
14. ASUS ASIC
15. 4-pin IPMB connector
Grand Champion
®
SCSI-Controller
®
PCI-PCI Bridge
16. LPC Super-I/O controller
17. 80-pin ASMB daughterboard connector
18. Serial port 2
19. ATI Rage-XL VGA controller
20. PCI-X slots (PCI-X1 to X4), PCI64, PCI32
®
21. Intel
22. Broadcom
23. PS/2 mouse port
24. Parallel port
25. RJ-45 ports
26. VGA port
27. Serial port 1
28. USB ports 1 and 2
29. Keyboard port
82540 32bit PCI Gigabit
Ethernet controller
®
5703CHK PCI-X
Gigabit Ethernet controller
1-6
See page 1-8 for the specifications of each component. Refer to Chapter 2 for detailed information on the components.
Chapter 1: Product introduction
Page 22
1 42 5
6
3
7 8
22
22 23
21 20
19
18
28 27 2426 25
16 13 11 91017
15
1214
ASUS PRL-DLS533 motherboard user guide
1-7
Page 23
1.4.2 Core specifications
1
604-pin CPU sockets. A 604-pin surface mount, Zero Insertion
Force (ZIF) socket for the Intel
®
Xeon™ processor with 512KB L2
cache and a 533MHz or a 400MHz system bus that allows up to
4.2GB/s or 3.2GB/s data transfer rate.
2
8-pin 12V SSI power connector. This power connector is for an
ATX power supply. 24/20-pin ATX power connector. This power connector is for an
ATX power supply.
3
ServerWorks
®
Grand Champion SuperLite north bridge CMIC-
SL. The Champion Memory and I/O Controller SuperLite (CMIC-
SL) acts as the host bridge of the Grand Champion SuperLite (GCSL) SystemSet. The GCSL device interfaces directly to the processor bus, and integrates the functions of the main memory controller and the Inter Module Bus (IMB) interface unit. The processor interface supports a 533MHz Front Side Bus (FSB) providing a 4.2GB/s bandwidth, memory bandwidth with up to 4GB registered ECC PC2100/1600 DDR DIMMs, and two high speed IMBs plus one thin IMB to connect to the south bridge CSB6.
4
DIP switches. This 5-switch Dual Inline Package (DIP) allows you
to set the CPU external frequency.
5
DDR DIMM sockets. These four 184-pin DIMM sockets support up to
4GB system memory using registered ECC PC2100/1600 DDR DIMMs.
6
Floppy disk connector . This connector accommodates the provided
ribbon cable for the floppy disk drive. One side of the connector is slotted to prevent incorrect insertion of the floppy disk cable.
7
ServerWorks
®
South Bridge, CSB6 performs as a PCI to LPC (Low Pin Count) Bridge and integrates PCI master/slave functions, DMA controller, ATA100 IDE interface, USB contoller, SMBus host, ACPI and other integral functions.
8
IDE connectors. These dual-channel bus master IDE connectors
support up to four Ultra DMA/100/66, PIO Modes 3 & 4 IDE devices. Both the primary (blue) and secondary (blue) connectors are slotted to prevent incorrect insertion of the IDE ribbon cable.
1-8
Third IDE (black) with PIO mode 3/4 support provides more device connectivity in this server system.
Chapter 1: Product introduction
Page 24
9
10
Ultra-160/320 SCSI connectors. These dual-channel 68-pin
Ultra-160/320 SCSI connectors support up to 30 SCSI devices, and data transfers of 160Mbps/320Mbps.
®
LSI
SCSI controller. The LSI 53C1030 SCSI controller supports
up to 30 SCSI devices through the onboard dual-channel SCSI connectors.
11
12
13
14
15
Flash ROM. This 4Mb firmware contains the programmable BIOS
program. DIP switches. This Dual Inline Package (DIP) switch allows you to
set the frequencies.
ServerWorks
®
64-bit I/O Bridge CIOB-X2. The Champion South Bridge provides a high performance data flow path between the IMB and the I/O subsystem, which supports multiple PCI-X interfaces that allows large, efficient, flexible I/O configurations. The CIOB-X2 supports dual 64-bit PCI-X I/O busses that comply with PCI 2.2 specifications.
ASUS ASIC. This chip performs multiple system functions that include hardware and system voltage monitoring, IRQ routing, among others.
4-pin IPMB Connector. This connector supports the ASUS daughter card, ASMB-LE/HE for local host management.
16
17
18
19
LPC super I/O controller. This Low Pin Count (LPC) interface
provides the commonly used Super I/O functionality. The chipset supports UART compatible serial ports, one parallel port with EPP and ECP capabilities, a floppy drive, and PS/2 keyboard and mouse.
80-pin ASMB Connector. This connector supports the ASMB proprietary Server Management daughter card.
ATI Rage-XL VGA controller. This PCI-based VGA controller supports up to 8MB display SDRAM for 1280x1024 and true color resolutions.
PCI-X/PCI slots. Four 64-bit/100MHz PCI-X slot and one 64-bit/ 33MHz PCI slots, and a 32-bit/33MHz PCI expansion slot support bus master PCI-X/PCI cards.
ASUS PRL-DLS533 motherboard user guide
1-9
Page 25
20
®
Intel
82540 32bit PCI Gigabit Ethernet controller Controller.
This LAN controller fully supports 10BASE-T/100BASE-TX/ 1000BASE-T networking protocols and data rates up to 1000Mbps.
21
22 23
24
25
Broadcom
®
5703CHK PCI-X Gigabit Ethernet Controller. This LAN controller fully supports 10BASE-T/100BASE-TX/1000BASE-T networking protocols and data rates up to 1000Mbps. The BCM5703 is optimized for LAN on Motherboard designs (LOM), enterprise networking, and Internet appliances that use PCI or PCI­X bus. The controller provides a 32/64-bit, 33/66MHz interface to the PCI bus that supports PCI Specification Rev. 2.2, and to the PCI-X extension to the PCI Local Bus Rev 1.0a at clock rates of up to 100MHz.
PS/2 mouse port. This green 6-pin connector is for a PS/2 mouse. Parallel port. This 25-pin port connects a parallel printer, a
scanner, or other devices. RJ-45 ports. These ports allows connection to a Local Area
Network (LAN) through a network hub. VGA port. This port is for a VGA-monitor or other VGA-compatible
devices.
26
27
28
Serial port. This 9-pin COM1 port is for pointing devices or other
serial devices. USB 1.1 ports. These two 4-pin Universal Serial Bus (USB) ports
are available for connecting USB devices. PS/2 keyboard port. This purple 6-pin connector is for a PS/2
keyboard.
1-10
Chapter 1: Product introduction
Page 26
Chapter 2
This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switches, jumpers, and connectors on the motherboard.
Hardware information
Page 27
Chapter summary
2.1 Motherboard installation ............................... 2-1
2.2 Motherboard layout ....................................... 2-2
2.3 Before you proceed ....................................... 2-3
2.4 Central Processing Unit (CPU) ..................... 2-4
2.5 System memory ............................................. 2-8
2.6 Expansion slots ............................................2-11
2.7 Switches and jumpers ................................. 2-14
2.8 Connectors ................................................... 2-19
ASUS PRL-DLS533 motherboard
Page 28
2.1 Motherboard installation
Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The PRL-DLS533 uses the extended ATX form factor that measures 12 inches x 13 inches (30.5 x 33 cm).
Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause you physical injury and damage motherboard components.
2.1.1 Placement direction
When installing the motherboard, make sure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below.
2.1.2 Screw holes
Place screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not overtighten the screws! Doing so may damage the motherboard.
Place this side towards the rear of the chassis
ASUS PRL-DLS533 motherboard user guide
2-1
Page 29
2.2 Motherboard layout
33.2cm (13.07in)
PS/2
T: Mouse B: Keyboard
USB1 USB2
COM1
VGA
RJ-45
RJ-45
JBCMLAN1
JLAN1
JVGA1
COM2
PARALLEL PORT
BroadCom
BCM5703C
PCI-X
Gigabit
Ethemet
Intel 82540 Gigagit
Ethernet
VGA RAM
ATI
RAGE XL
VGA
Controller
mPGA604mPGA604
PCIX-1 (64-bit, 100MHz 3V)
PCIX-2 (64-bit, 100MHz 3V)
PCIX-3 (64-bit, 100MHz 3V)
STBYLED1
PCIX-4 (64-bit, 100MHz 3V)
PCI64 (64-bit, 33MHz 3V)
PCI32 (32-bit, 33MHz 5V)
CON1
FAN1
Super
I/O
CON2
FAN2
CON12V
ATX_POWER
CPULED1
GCSL
JFSB1
FAN3
ServerWorks
CIOB-X2
I/O Bridge
CLRCMOS1
ASUS ASIC
with Hardware
Monitor
J1
J2
®
ASUS PANEL1
ServerWorks North Bridge
SW1
DDR DIMM1 (64/72 bit, 184-pin module)
DDR DIMM2 (64/72 bit, 184-pin module)
DDR DIMM3 (64/72 bit, 184-pin module)
DDR DIMM4 (64/72 bit, 184-pin module)
0 1
2 3
4 5
6 7
PRL-DLS533
ServerWorks
RCC
CSB6
South Bridge
4Mbit
®
Flash BIOS
LED2
LED1
SW2
LED3
LED5
LED4
BUZZ1
®
LED6
LED7
LED8
FLOPPY
CR2032 3V Lithium Cell
CMOS Power
IDE2
JSCSI1
®
LSI 53C1030
SCSI
Controller
JSLED1
34 1
3568
SCSI1
SCSI2
POWERLED1
IDE3
IDE1
®
30.7cm (12.08in)
2-2
The SCSI features are optional. These components are grayed out in the above motherboard layout.
Chapter 2: Hardware information
Page 30
2.3 Before you proceed
Take note of the following precautions before you install motherboard components or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any component.
2. Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity.
3. Hold components by the edges to avoid touching the ICs on them.
4. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component.
5. Before you install or remove any component, ensure that the
ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause
severe damage to the motherboard, peripherals, and/or components.
ASUS PRL-DLS533 motherboard user guide
2-3
Page 31
2.4 Central Processing Unit (CPU)
2.4.1 Overview
The motherboard comes with dual surface mount 604-pin Zero Insertion Force (ZIF) sockets. The sockets are designed for the Intel Processor in the 604-pin package with 512KB L2 cache. The processor includes the
®
Intel
NetBurst™ micro-architecture that features the hyper-pipelined technology, rapid execution engine, 400MHz or 533MHz system bus, and execution trace cache. Together, these attributes improve system performance by allowing higher core frequencies, faster execution of integer instructions, and data transfer rate of up to 3.2GB/s or 4.2GB/s.
Prestonia
®
PRL-DLS533
Gold Arrow
PRL-DLS533 Socket 604
Note in the illustration that the CPU has a gold triangular mark on one corner. This mark indicates the processor Pin 1 that should match a specific corner of the CPU socket.
Incorrect installation of the CPU into the socket may bend the pins and severely damage the CPU!
The motherboard supports either one or two CPUs. If you are installing only one CPU, you MUST install it in CPU socket 1.
CPU Socket 2 (outer socket)
2-4
CPU Socket 1 (inner socket)
Chapter 2: Hardware information
Page 32
2.4.2 Installing the CPU
If you are installing two CPUs, install in the CPU socket 2 first.
Follow these steps to install a CPU.
1. Locate the 604-pin ZIF sockets on the motherboard. Unlock the socket by pressing the lever sideways, then lift it up to at least 115° angle.
Make sure that the socket lever is lifted up to at least 115° angle, otherwise the CPU does not fit in completely.
2. Position the CPU above the socket as shown.
3. Carefully insert the CPU into the socket until it fits in place.
Marked Corner
The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU!
4. When the CPU is in place, press it firmly on the socket while you push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked.
ASUS PRL-DLS533 motherboard user guide
2-5
Page 33
2.4.3 Installing the CPU heatsink and fan
The Intel
®
Xeon™ processors require aspecially designed heatsink and
fan assembly to ensure optimum thermal condition and performance. Follow these steps to install the CPU heatsink and fan.
1. Place the heatsink and fan assembly on top of the installed CPU, making sure that it fits in place.
2. Hook one end of the retention bracket into the protruding tab on the corner of the plastic retention base. (The retention base comes installed with the motherboard.)
2-6
Chapter 2: Hardware information
Page 34
3. Use a small flat screw driver to attach the other end of the bracket, while firmly holding down the heatsink and fan assembly. The middle hook of the bracket snaps in place if you properly attached the two ends.
4. As shown, the middle hook of the bracket snaps in place if you properly attached the two ends.
5. Do steps 2 to 4 to install the other bracket.
6. When the heatsink and fan assembly is in place, connect the fan cable to the fan connector on the motherboard labeled CPUFAN1 (for the CPU on socket
1) and CPUFAN2 (for the CPU on socket 2).
Don’t forget to connect the CPU fan cable. Hardware monitoring problems may occur if you fail to plug the cable.
ASUS PRL-DLS533 motherboard user guide
2-7
Page 35
2.5 System memory
2.5.1 Overview
The motherboard comes with six Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 4GB system memory using 184-pin registered PC2100/1600 DIMMs with Serial Presence Detect (SPD) and Error Check and Correction (ECC).
104 Pins
®
PRL-DLS533
80 Pins
PRL-DLS533 184-Pin DDR DIMM Sockets
A DDR DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into a socket to avoid damaging the DIMM.
The DDR SDRAM technology evolved from the mainstream PC66, PC100, PC133 memory known as Single Data Rate (SDR) SDRAM. DDR memory however, has the ability to perform two data operations in one clock cycle, thus providing twice the throughput of SDR memory. For example, a 200MHz DDR DIMM will support a 100MHz memory bus, and a 266MHz DDR DIMM will support a 133MHz memory bus.
DDR Data Transfer Rate DDR Base Frequency
266MHz 133MHz 200MHz 100MHz
A DDR DIMM has the same physical dimensions as an SDR DIMM, but it has a 184-pin footprint compared to the 168-pin of the SDR DIMM. Also, a DDR DIMM is single notched while an SDR DIMM is double notched. Therefore, a DDR DIMM is not backward compatible with SDR, and should be installed only in a socket specially designed for DDR DIMMs.
2-8
Chapter 2: Hardware information
Page 36
2.5.2 Memory Configurations
The motherboard supports system memory of up to 4GB in a one-way non-interleaved configuration.
Memory configuration table
DIMM Socket 184-pin ECC DDR DIMM Total Memory
DDR1 SDRAM 128MB, 256MB, 512MB, 1GB, 2GB (x1) = DDR2 SDRAM 128MB, 256MB, 512MB, 1GB, 2GB (x1) = DDR1 SDRAM 128MB, 256MB, 512MB, 1GB, 2GB (x1) = DDR2 SDRAM 128MB, 256MB, 512MB, 1GB, 2GB (x1) =
Total System Memory (Max. 4GB) =
The system chipset only supports PC2100/1600 registered ECC DIMMs. Make sure to use only the specified DIMM types for stable system operation.
ASUS PRL-DLS533 motherboard user guide
2-9
Page 37
2.5.3 Installing a DIMM
Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components.
Follow these steps to install a DIMM.
1. Unlock a DIMM socket by pressing the retaining clips outward.
2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket.
Unlocked Retaining Clip
3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated.
Locked Retaining Clip
2.5.4 Removing a DIMM
Follow these steps to remove a DIMM.
1. Simultaneously press the retaining clips outward to unlock the DIMM.
2. Remove the DIMM from the socket.
Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force.
2-10
Chapter 2: Hardware information
Page 38
2.6 Expansion slots
In the future, you may need to install expansion cards. The following sub­sections describe the slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.
2.6.1 Installing an expansion card
Follow these steps to install an expansion card.
1. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card.
2. Remove the system unit cover (if your motherboard is already installed in a chassis).
3. Remove the bracket opposite the slot that you intend to use. Keep the screw for later use.
4. Align the card connector with the slot and press firmly until the card is completely seated on the slot.
5. Secure the card to the chassis with the screw you removed earlier.
6. Replace the system cover.
2.6.2 Configuring an expansion card
After installing the expansion card, configure the it by adjusting the software settings.
1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 4 for information on BIOS setup.
2. Assign an IRQ to the card. Refer to the tables on the next page.
3. Install the software drivers for the expansion card.
ASUS PRL-DLS533 motherboard user guide
2-11
Page 39
Standard Interrupt Assignments
IRQ Priority Standard Function
0 1 System Timer 1 2 Keyboard Controller 2 N/A Programmable Interrupt 3* 11 Communications Port (COM2) 4* 12 Communications Port (COM1) 5* 13 Sound Card (sometimes LPT2) 6 14 Floppy Disk Controller 7* 15 Printer Port (LPT1) 8 3 System CMOS/Real Time Clock 9* 4 ACPI Mode when used 10* 5 IRQ Holder for PCI Steering 11* 6 IRQ Holder for PCI Steering 12* 7 PS/2 Compatible Mouse Port 13 8 Numeric Data Processor 14* 9 Primary IDE Channel 15* 10 Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
IRQ assignments for this motherboard
PCI INTA PCI INTB PCI INTC PCI INTD
PCI-X slot 1 12 13 14 15 PCI-X slot 2 8 9 10 11 PCI-X slot 3 27 28 19 20 PCI-X slot 4 23 24 25 26 PCI64 slot 5 19 20 21 22 PCI32 slot 6 3 4 5 6 Onboard 82540 controller 2 — Onboard BCB5703 controller 7 — Onboard SCSI controller 17 18 — Onboard VGA controller 1
When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable.
2-12
Chapter 2: Hardware information
Page 40
2.6.3 PCI slots
This motherboard implements the PCI-X (Peripheral Component Interconnect Extended) bus technology to support up to 100MHz data transfers, or about 800MB/s. This bus technology is primarily designed for servers to increase the performance of high bandwidth devices such as Gigabit Ethernet cards and Ultra320 SCSI interfaces. PCI-X is backward compatible with the earlier PCI bus technology making it possible to install PCI and PCI-X cards at the same time, but the bus speed will be that of the slowest card. The following figure shows the five PCI-X slots and one PCI slot on the motherboard.
PCI-X1 PCI-X2 PCI-X3
PCI-X4 PCI64 PCI32
PCI-X slots (PCI X1 to X4)
The motherboard may come with either the LSI
®
53C1010R or the LSI 53C1030 SCSI controller . Depending on the onboard SCSI controller, the following table shows the varying bus speeds for the PCI-X slots according to the PCI-X specification 1.0a.
PCI-X Slot
Onboard SCSI
53C1030 64-bit/100MHz PCI-X 64-bit/100MHz PCI-X 64-bit/33MHz PCI
*
PCI-X3 supports the AMI MegaRAID 320-0 or Intel SRU ZCR Card
PCI-X1 to PCI-X3* to PCI-X2 PCI-X4 PCI64
®
PCI slot (PCI32)
PCI32 is a 32-bit/33MHz 5V PCI slot with a Low Pin Count (LPC) signal connector to accommodate the ASUS Server Management Card. This slot has the same specifications regardless of the onboard SCSI controller .
PCI slot (PCI64)
PCI64 is a 64-bit/33MHz 3.3V PCI slot which supports up to 266MB/s bandwidth and supports most PCI expansion cards used in servers.
ASUS PRL-DLS533 motherboard user guide
2-13
Page 41
2.7 Switches and jumpers
t)
z
SW1
z
2.7.1 Switches
The following figure shows the location and default settings of the DIP switches on the motherboard.
Keep the default settings for stable system operation.
SW2
ON
PRL-DLS533
PRL-DLS533 DIP Switches
12345678
®
OFF ON
1. Reserved
2. Reserved
3. Reserved
4. Reserved
5. Frequency Multiple
6. Frequency Multiple
7. Frequency Multiple
8. Frequency Multiple
1. CPU External Frequency Selection (SW1 & JFSB1)
This option tells the clock generator which frequency to send to the CPU, SDRAM and AGP clock, and sets the CPU’s External frequency. (The BUS Clock multiplied by the Frequency Multiple equals the CPU’s Internal frequency, or, the advertised CPU speed.)
®
PRL-DLS533
PRL-DLS533 CPU External Frequency Selection
ON
12345
400MHz
JFSB1
2 1
400MHz
ON
12345
533MH
3 2
533MH
(Defaul
2-14
Both the dip switch and jumper must be set together.
Chapter 2: Hardware information
Page 42
2. CPU Frequency Multiple Setting (SW2 Switches 5-8)
SW2
Set DSW switches (1-4) to use the clock multiplier to coordinate the ratio of bus speeds with CPU settings. Set the DSW switches according to the internal speed of your processor and the bus frequency (133/100MHz).
ON
12345678
ON
12345678
12345678
ON
ON
12345678
ON
ON
ON
10.0x
ON
12345678
14.0x
ON
12345678
18.0x
ON
12345678
22.0x
PRL-DLS533
PRL-DLS533 CPU Frequency Multiple Selection
8.0x
12345678
13.0x
12345678
®
17.0x
12345678
21.0x
MultiplierTable
Multiplier DSW
5 6 7 8
8.0x [OFF] [OFF] [OFF] [OFF]
10.0x [OFF] [ON] [OFF] [OFF]
11.0x [ON] [ON] [OFF] [OFF]
12.0x [OFF] [OFF] [ON] [OFF]
13.0x [ON] [OFF] [ON] [OFF]
14.0x [OFF] [ON] [ON] [OFF]
15.0x [ON] [ON] [ON] [OFF]
16.0x [OFF] [OFF] [OFF] [ON]
17.0x [ON] [OFF] [OFF] [ON]
18.0x [OFF] [ON] [OFF] [ON]
19.0x [ON] [ON] [OFF] [ON]
20.0x [OFF] [OFF] [ON] [ON]
21.0x [ON] [OFF] [ON] [ON]
22.0x [OFF] [ON] [ON] [ON]
23.0x [ON] [OFF] [OFF] [OFF]
24.0x [ON] [ON] [ON] [ON]
11.0x
12345678
15.0x
12345678
19.0x
12345678
23.0x
ON
ON
ON
12.0x
ON
12345678
16.0x
ON
12345678
20.0x
ON
12345678
24.0x
ASUS PRL-DLS533 motherboard user guide
2-15
Page 43
t)
)
2.7.2 Jumpers
1. SCSI setting (2-pin JSCI1)
This jumper allows you to enable or disable the onboard SCSI feature. Keep the jumper open if you wish to install SCSI devices. Place a cap on the jumper to disable the onboard SCSI controller.
®
PRL-DLS533
PRL-DLS533 LSI 1030 SCSI Chip Setting
JSCSI1
32 12
EnableDisable
(Default
2. 32-bit PCI Gigabit Ethernet setting (1 x 3-pin JLAN1)
These jumpers are set by default, pins [1-2], to enable the onboard INTEL 82540 Gigabit Ethernet controller to support 10/100/1000BASE networks. Set to pins 2-3 to disable the controller.
®
PRL-DLS533
PRL-DLS533 Intel 82540 LAN Chip Setting
JLAN1
32 12
EnableDisable
(Defaul
2-16
Chapter 2: Hardware information
Page 44
e
e
3. PCI-X Gigabit Ethernet setting (3-pin JBCMLAN1)
This jumper is set by default, pins [1-2], to enable the onboard Broadcom BCM5703 Gigabit Ethernet controller to support 10/100/ 1000BASE networks. Set to pins 2-3 to disable the controller.
PRL-DLS533
®
JBCMLAN1
1 2
Enable Disabl
(Default)
2 3
PRL-DLS533 Broadcom 5703 LAN Chip Setting
4. VGA setting (3-pin JVGA1)
This jumper is set by default, pins [1-2], to enable the onboard the onboard ATI Rage XL VGA controller. Reset to pins 2-3 to disable the VGA controller.
PRL-DLS533
®
JVGA1
2 1
Enable Disabl
(Default)
PRL-DLS533 ATI RageXL VGA Setting
ASUS PRL-DLS533 motherboard user guide
3 2
2-17
Page 45
5. Clear RTC RAM (CLRCMOS1)
These solder pads allow you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The RAM data in CMOS, that include system setup information such as system passwords, is powered by the onboard button cell battery.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the battery.
3. Short the solder pads for about 5 seconds.
4. Re-install the battery.
5. Plug the power cord and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data.
PRL-DLS533
PRL-DLS533 Clear RTC RAM
®
CLRCMOS1
Short solder points to Clear CMOS
2-18
Chapter 2: Hardware information
Page 46
2.8 Connectors
n
This section describes and illustrates the internal connectors on the motherboard.
Always connect ribbon cables with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives.
1. Floppy disk drive connector (34-1 pin FLOPPY1)
This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug).
FLOPPY1
®
PRL-DLS533
PIN 1
NOTE: Orient the red markings o the floppy ribbon cable to PIN 1.
PRL-DLS533 Floppy Disk Drive Connector
2. Serial port 2 connector (10-1 pin COM2)
This connector accommodates a second serial port using an optional serial port bracket. Connect the bracket cable to this connector then install the bracket into a slot opening at the back of the system chassis.
PRL-DLS533
®
PIN 1
PRL-DLS533 Serial COM2 Connector
ASUS PRL-DLS533 motherboard user guide
2-19
Page 47
3. IDE connectors (two 40-1 pin IDE1, IDE2, IDE3)
s
This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon cable. Connect the cable’s blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraDMA/100/66 slave device (hard disk drive) and the black connector to the UltraDMA/100/66 master device. It is recommended that you connect non-UltraDMA/100/66 devices to the secondary IDE connector. If you install two hard disks, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. BIOS supports specific device bootup. If you have more than two UltraDMA/100/66 devices, purchase another UltraDMA/100/66 cable. You may configure two hard disks to be both master devices with two ribbon cables – one for the primary IDE connector and another for the secondary IDE connector.
1. Pin 20 on each IDE connector is removed to match the covered hole on the UltraDMA cable connector. This prevents incorrect orientation when you connect the cables.
2. The hole near the blue connector on the UltraDMA/100/66 cable is intentional.
3. IDE3 only supports PIO Mode 4
IDE1
PIN 1
PRL-DLS533
PRL-DLS533 IDE Connectors
®
IDE2
PIN 1
IDE3
PIN 1
NOTE: Orient the red marking (usually zigzag) on the IDE ribbon cable to PIN 1.
For UltraDMA/100/66 IDE devices, use an 80-conductor IDE cable. The UltraDMA/66 cable included in the motherboard package also supports UltraDMA/100.
2-20
Chapter 2: Hardware information
Page 48
4. Chassis alarm lead (4-1 pin J3)
This lead is for a chassis designed with intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch. When you remove any chassis component, the sensor triggers and sends a high-level signal to this lead to record a chassis intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted with a jumper cap. If you wish to use the chassis intrusion detection feature, remove the jumper cap from the pins.
®
PRL-DLS533
+5Volt
(Power Supply Stand By)
Chassis Signal
Ground
J3
PRL-DLS533 Chassis Open Alarm Lead
5. Wake-On-Ring Connector (2-pin J2)
This connector connects to internal modem cards with a Wake-On­Ring output. The connector powers up the system when a ringup packet or signal is received through the internal modem card.
For external modems, Wake-On-Ring is detected through the COM port.
®
PRL-DLS533
J2
PRL-DLS533 Wake on Ring Header
ASUS PRL-DLS533 motherboard user guide
2-21
Page 49
6. ATX power connectors (24/20-pin ATXPWR, 8-pin CON12V)
For Power Supply
These connectors connect to an ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.
In addition to the 24/20-pin ATXPWR connector, this motherboard requires that you connect the 8-pin ATX +12V power plug to provide sufficient power to the CPU.
Make sure that your ATX 12V power supply can provide 8A on the +12V lead and at least 2A on the +5-volt standby lead (+5VSB). The minimum recommended wattage is 230W, or 300W for a fully configured system. The system may become unstable and may experience difficulty powering up if the power supply is inadequate.
with 20-pin
Power Connector
ATXPWR
24-pin Power Connector
®
PRL-DLS533
PRL-DLS533 ATX Power Connector
1
CON12V
+3 Volts
+3 Volts
-12 Volts
+3 Volts
GND GND GND GND
Ground
PSON#
Ground
+5 Volts
Ground
Ground
Ground
+5 Volts
-5 Volts
Ground
Ground
Power OK
12V 12V 12V 12V
+5 Volts
+5 Volts
+5 Volts
Ground
+3 Volts
+12 Volts
+12 Volts
+5V Standby
8-pin
4-pin
2-22
Chapter 2: Hardware information
Page 50
3
4
7. CPU, Chassis, and Power Fan Connectors
S
(3-pin FAN1, FAN2, FAN3)
The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Lack of sufficient air flow within the system may damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors!
PRL-DLS533
FAN1
Rotation
+12V
GND
®
FAN
GND
Rotation
+12V
FAN2 FAN
GND
Rotation
+12V
GND
+12V
Rotation
PRL-DLS533 12-Volt Cooling Fan Power
8. Zero Channel RAID Slot (PCI-X3)
The PCI-X3 slot supports a standard PCI expansion card as well as a Zero Channel RAID card like the one from LSI shown here.
PRL-DLS533
PRL-DLS533 Zero Channel RAID
®
ASUS PRL-DLS533 motherboard user guide
2-23
Page 51
9. Server management card connector (50-pin eRMC)
This connector allows you to connect the optional ASMC-LE, ASMC-ME, or ASMC-HE card using an ASMC interface cable. Install the ASMC card into the PCI6 slot and connect the cable from the card to this connector. The PCI6 slot on the motherboard has a Low Pin Count (LPC) signal connector to accommodate the ASMC card.
®
PRL-DLS533
PRL-DLS533 eRMC Connector
10.IPMB connector (4-pin CON2)
The Intelligent Platform Management Bus (IPMB) connector is for the ASMC card. Connect the 4-pin ASMC interface cable to this connector.
®
PRL-DLS
CON2
NC
GND
PRL-DLS IPMB Connector
IPMIDATA
IPMICLK
2-24
Chapter 2: Hardware information
Page 52
68-pin Internal SCSI Cable (Twisted-Pair Ribbon)
11. Two 68-pin Ultra160/320 SCSI Connectors (SCSI1, SCSI2)
This motherboard has two 68-Pin Ultra160/320 SCSI connectors; one for each of the two channels. Each channel can support a maximum of 15 devices as specified by Ultra160/320 standards.
PRL-DLS533
SCSI1
68-Pin Ultra160/ Ultra2-Wide SCSI Connector
®
35
1
SCSI2
68-Pin Ultra160/ Ultra2-Wide SCSI Connector
34 1
3568
6834
PRL-DLS533 Onboard SCSI Connectors
SCSI Connection Notes
This motherboard has two 68-Pin Ultra160/320 SCSI connectors; one for each of the two channels.
The onboard SCSI chipset incorporates an advanced multimode I/O cell that supports both single-ended (SE), Ultra2, and Ultra160/320 devices. With Ultra160/320 devices, the SCSI bus platform performs at full Ultra160/320 speeds (up to 160MB/s or 320MB/s) and extended cabling 12m (or 25m in a point-to-point configuration). When an SE device is attached, the bus defaults to an SE speed and 1.5m cable length.
Connect SCSI devices as shown. Each channel should have only one type of SCSI standard (e.g. Ultra320, Ultra160, Ultra2, Ultra-Wide). Mixing SCSI devices on the same channel decreases performance of the slower device.
Internal SCSI Devices (up to 15 devices)
®
PRL-DLS533
68-pin Internal SCSI Cable (Twisted-Pair Ribbon)
Internal SCSI Devices (up to 15 devices)
PRL-DLS533 SCSI Connection Example
ASUS PRL-DLS533 motherboard user guide
Channel B
68-pin Female Terminator
Channel A
68-pin Female Terminator
2-25
Page 53
12.System panel connector (20-pin PANEL)
This connector accommodates several system front panel functions.
PLED
MLED
Keylock
Ground
Speaker Connector
Speaker
Ground
+5V
Ground
20 10
PWR
Reset
Ground
Ground
Reset SW
ATX Power Switch*
PRL-DLS533
Keyboard Lock
Power LED
+5 VSB
®
11
1
+5 VSB
Message LED
PRL-DLS533 System Panel Connectors
System Power LED Lead (3-1 pin PLED)
This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
System Message LED Lead (2-pin MLED)
This 2-pin connector is for the system message LED that indicates receipt of messages from a fax/modem. The normal status for this LED is OFF, when there is no incoming data signal. The LED blinks when data is received. The system message LED feature requires an ACPI OS and driver support.
System Warning Speaker Lead (4-pin SPEAKER)
This 4-pin connector is for a chassis-mounted speaker.
ATX Power Switch / Soft-Off Switch Lead (2-pin PWR)
This connector connects a switch that controls the system power. Pressing the power switch turns the system between ON and SLEEP, or ON and SOFT OFF, depending on the BIOS or OS settings. Pressing the power switch while in the ON mode for more than 4 seconds turns the system OFF.
Reset Switch Lead (2-pin RESET)
This 2-pin connector connects to the case-mounted reset switch for rebooting the system without turning off the system power.
2-26
Chapter 2: Hardware information
Page 54
2.9 Onboard LEDs
P
FAN1
mPGA604mPGA604
PCIX-1 (64-bit, 100MHz 3V)
PCIX-2 (64-bit, 100MHz 3V)
CON12V
ATX_POWER
CPULED1
ServerWorks North Bridge
®
GCSL
JFSB1
FAN3
SW1
DDR DIMM1 (64/72 bit, 184-pin module)
DDR DIMM2 (64/72 bit, 184-pin module)
DDR DIMM3 (64/72 bit, 184-pin module)
DDR DIMM4 (64/72 bit, 184-pin module)
0 1
2 3
4 5
6 7
PRL-DLS533
CR2032 3V Lithium Cell
CMOS Power
IDE2
FLOPPY
ServerWorks
RCC
CSB6
South Bridge
®
®
POWERLED1
IDE3
IDE1
PCIX-3 (64-bit, 100MHz 3V)
STBYLED1
PCIX-4 (64-bit, 100MHz 3V)
PCI64 (64-bit, 33MHz 3V)
CI32 (32-bit, 33MHz 5V)
CON1
Super
I/O
CON2
FAN2
ServerWorks
CIOB-X2
I/O Bridge
CLRCMOS1
ASUS
ASIC
with Hardware
Monitor
ASUS PANEL1
J1
J2
4Mbit
®
Flash
BIOS
LED2
LED1
LED3
SW2
LED6
LED5
LED4
BUZZ1
JSCSI1
®
LSI 53C1030
LED7
LED8
SCSI
Controller
JSLED1
34 1
3568
SCSI1
SCSI2
Onboard LEDs
CPULED1 Lights if one or two CPU overheats or if CPU 1 is not inserted. POWERLED1 Lights when the motherboard is turned ON. STBYLED1 Lights when the motherboard receives standby power. LED1-LED8 Port 80h post code LEDs (see next page) JSLED1 SCSI activity LED header (for chassis LED)
ASUS PRL-DLS533 motherboard user guide
2-27
Page 55
2.9.1 Port 80h post code LEDs
LED
8 7 6 5 4 3 2 1
FFh C0h
0Dh
00h
POST Code < C0h >
1. Chipset very early initialization.
2. Programed chipset registers before memory detection.
POST Code < C1h >
1. Power on check.
2. Memory detection and initialization. POST Code < 80h > : Get memory type from SPD. If BIOS can’t get SPD = Error Code < D0h > If memory type is not DDR-SDRAM = Error Code < D8h > POST Code < 81h > : Get size and timing information from SPD. POST Code < 82h > : Set memory size according to each memory module. POST Code < 83h > : Set memory timing. POST Code < 84h > : Initialize memory module. POST Code < 85h > : Do DQS for memory module. POST Code < 86h > : Finish memory detection and initialization
3. Test first 256 MB memory.
POST Code < 0Ch >
1. BIOS checksum verify.
POST Code < C3h >
1. Decompressed BIOS codes into memory.
POST Code < C5h >
1. Shadow system BIOS.
2-28
Chapter 2: Hardware information
Page 56
2. Disabled CPU cache.
3. Check if go to BOOTBLOCK POST.
POST Code < 05h >
1. Blank out the video screen.
2. Initialized the keyboard.
POST Code < 07h >
1. Used walking 1's algorithm to check out interface to CMOS circuitry.
2. Also set real-time clock power status. Then check for override.
POST Code < 09h >
1. Programed chipset register to default value according to ROMTABLE.
2. early initialize CPU.
3. Initialized APIC.
4. Set A20 off.
POST Code < 0Ah >
1. Initialized int. vectors (0-77h) to the spurious interrupt handler. Then initialize 00h-1fh to their proper places.
POST Code < 0Bh >
1. Checked normal ISA CMOS checksum and battery . If it fails, we load the manufacturing defaults.
2. Chipset very early PM initialization, change SMBASE for CPU and move SMM code.
3. PMM initialization.
4. Disable all memory caching then enable E800 and F000 segement caching.
5. PnP early initialization.
6. BBS initialization.
POST Code < 0Ch >
1. Initialize the keyboard controller and set up all of the 40: area data.
2. Load CPU micro-code update if BIOS updated option is enable.
ASUS PRL-DLS533 motherboard user guide
2-29
Page 57
POST Code < 0Dh >
1. Programed CPU MTRR. Measure CPU speed and save CPU speed.
2. Initialized the video, whether it is mono, color or EGA/VGA. After initialize, shrink the VGA BIOS.
3. If no video found in this stage, beep a warning sound.
POST Code < 0Eh >
1. Set A20 on.
2. Showed HP Logo or Award Logo
3. Showed CPU type on screen.
POST Code < 14h >
1. Test 8254 Channel 2.
POST Code < 18h >
1. Test 8259 functionality.
POST Code < 30h >
1. Disabled D0/D1 command to KBC, wait for command accepted.
2. Special KBC Initialization (set KBC to PS2 mode).
3. Sizing base memory (0-640K) and extended memory starting at just over the 1M boundary.
Will continue until fail to read what was written or come to the 3GB boundary .
POST Code < 31h >
1. Set CPU MTRR for address above 1MB.
2. Cleared base memory.
3. Build UMB structure.
4. Initialized USB.
5. Erased all of memory above 1MB if QUICK_POST is disabled.
POST Code < 32h >
1. Displayed AWARD PNP message. (Award_PnP_Msg)
2. Initialized onboard SuperIO. a. Early IDE chip initialize. b. Programed SuperIO chip.
2-30
Chapter 2: Hardware information
Page 58
POST Code < 3Dh >
1. Initialize and install mouse and 40: area stuff...
2. Set extended memory size.
3. Save EXT_MEM_Size_MB in G_RAM.
4. Expanded ACPI table into memory.
5. Setup ACPITable and ACPINVS Size.
6. According to length of ACPI table to decrease Ext_MEM_FOUND, EXT_MEMORY.
7. After extended memory test, copy all ACPI tables to ACPI reclaim area (just below top of extended memory , see A TBASE INT15 function 0e820h).
Then fill in physical address and checksum for all ACPI tables.
8. Get extended memory size and set size for E801h.
9. Check USB Legacy Mode.
10.Installed Mouse.
POST Code < 3Eh >
1. Do external cache sizing if it cannot be detected correctly after onboard memory configuration (just return).
POST Code < 41h >
1. Programed chipset registers accroding to menuitem setting.
2. Installed floppy devices.
POST Code < 42h >
1. Installed hard disks.
POST Code < 45h >
1. Initialized and installed co-processor.
POST Code < 4Eh >
1. Checked whether the keyboard is locked or not.
2. Report USB Keyboard.
3. Translate HaltOn_Item value to tell whether individual catagory error should be reported or not.
ASUS PRL-DLS533 motherboard user guide
2-31
Page 59
POST Code < 4Fh >
1. Power management initialization.
2. Verify password.
POST Code < 50h >
1. Write all of CMOS back to RAM.
POST Code < 52h >
1. Do whatever needs to do before PCI ROM initialization.
2. Shadow adaptor card's ROM.
3. Do whatever need to do after PCI ROM initialization.
4. Build BBS Table.
5. Set segement f000 to shadow write.
6. Save SCSI card information.
7. Set segement f000 to shadow read.
8. Enable parity and NMI.
9. Enable IRQ 12 if PS2 mouse hot plug.
10.Enable BIOS Setup.
POST Code < 60h >
1. Set up PS2.
POST Code < 61h >
1. Enable L1/L2 cache according to BIOS setup option.
2. Chipset final initialization.
3. Chipset power management final initialization.
4. Show system configuration.
POST Code < 62h >
1. Force NUM-LOCK on 101-key keyboard.
2. Clear LEd first.
3. Set NumLock status according BIOS setup.
4. Set Typematic rate according BIOS setup.
2-32
Chapter 2: Hardware information
Page 60
POST Code < 63h >
1. Send D2 command following with dummy code 80h for PM to check power down.
2. PNP final initialization.
3. Enable Boot Menu.
4. Check RTC clock data (hour, minute and second), if error set register A to default value.
5. Set up low stack.
6. Clear any pending keystroke and KB queue buffer.
7. Clear garbage in base memory except BIOS data.
8. Set segment EC00 to EFFF shadow read/write.
9. Set segment EC00 to EFFF shadow read/write.
10.Set A20 off.
POST Code < ffh >
1. INT 19h (system boot).
ASUS PRL-DLS533 motherboard user guide
2-33
Page 61
2-34
Chapter 2: Hardware information
Page 62
Chapter 3
This chapter describes the power up sequence and gives information on the BIOS beep codes.
Powering up
Page 63
Chapter summary
3.1 Starting up for the first time.......................... 3-1
3.2 Powering off the computer ........................... 3-2
ASUS PRL-DLS533 motherboard
Page 64
3.1 Starting up for the first time
1. After making all the connections, replace the system case cover.
2. Be sure that all switches are off.
3. Connect the power cord to the power connector at the back of the system chassis.
4. Connect the power cord to a power outlet that is equipped with a surge protector.
5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power (if you are using an ATX power supply , you need to
switch on the power supply as well as press the ATX power switch on the front of the chassis).
6. After applying power, the power LED on the system front panel case lights up. For ATX power supplies, the system LED lights up when you press the ATX power switch. If your monitor complies with “green” standards or if it has a “power standby” feature, the monitor LED may light up or switch between orange and green after the system LED turns on. The system then runs the power-on tests. While the tests are running, the BIOS beeps or additional messages appear on the screen. If you do not see anything within 30 seconds from the time you turned on the power , the system may have failed a power-on test. Check the jumper settings and connections or call your retailer for assistance.
Award BIOS Beep Codes
Beep Meaning
One short beep when No error during POST displaying logo
Long beeps in an endless loop No DRAM installed or detected One long beep followed by Video card not found or video card
three short beeps memory bad High frequency beeps when CPU overheated;
system is working System running at a lower frequency
7. At power on, hold down <Delete> to enter BIOS Setup. Follow the instructions in Chapter 4.
ASUS PRL-DLS533 motherboard user guide
3-1
Page 65
3.2 Powering off the computer
You must first exit the operating system and shut down the system before switching off the power. For ATX power supplies, you can press the ATX power switch after exiting or shutting down the operating system. If you use Windows 95/98/2000/XP, click the Start button, click Shut Down, then click the OK button to shut down the computer. The power supply should turn off after Windows shuts down.
The message “You can now safely turn off your computer” does not appear when shutting down with ATX power supplies.
3-2
Chapter 3: Powering up
Page 66
Chapter 4
This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
BIOS setup
Page 67
Chapter summary
4.1 Managing and updating your BIOS .............. 4-1
4.2 BIOS Setup program...................................... 4-5
4.3 Main Menu ...................................................... 4-8
4.4 Advanced Menu ........................................... 4-15
4.5 Power Menu.................................................. 4-22
4.6 Boot Menu .................................................... 4-27
4.7 Server Menu ................................................. 4-29
4.8 Exit Menu ...................................................... 4-30
ASUS PRL-DLS533 motherboard
Page 68
4.1 Managing and updating your BIOS
4.1.1 Creating a bootable disk
AFLASH.EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode. To determine the BIOS version of your motherboard, check the last four numbers of the code displayed on the upper left-hand corner of your screen during bootup. Larger numbers represent a newer BIOS file.
1. Type FORMAT A:/S at the DOS prompt to create a bootable system disk. DO NOT copy AUTOEXEC.BAT and CONFIG.SYS to the disk.
2. Type COPY D:\AFLASH\AFLASH.EXE A:\ (assuming D is your CD-ROM drive) to copy AFLASH.EXE to the boot disk you created.
AFLASH works only in DOS mode. It does not work in the DOS prompt within Windows, and does not work with certain memory drivers that may be loaded when you boot from the hard drive. It is recommended that you reboot using a floppy disk.
3. Reboot the computer from the floppy disk.
BIOS setup must specify “Floppy” as the first item in the boot sequence.
4. In DOS mode, type A:\AFLASH <Enter> to run AFLASH.
If the word “unknown” appears after Flash Memory:, the memory chip is either not programmable or is not supported by the ACPI BIOS and therefore, cannot be programmed by the Flash Memory Writer utility.
ASUS PRL-DLS533 motherboard user guide
4-1
Page 69
5. Select 1. Save Current BIOS to File from the Main menu and press <Enter>. The Save Current BIOS To File screen appears.
6. Type a filename and the path, for example, A:\XXX-XX.XXX, then press <Enter>.
4-2
Chapter 4: BIOS Setup
Page 70
4.1.2 Updating the BIOS
Update the BIOS only if you have problems with the motherboard and you are sure that the new BIOS revision will solve your problems. Careless updating may result to more problems with the motherboard!
1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONTACT INFORMATION on page x for details) and save to the boot floppy disk you created earlier.
2. Boot from the floppy disk.
3. At the “A:\” prompt, type AFLASH and then press <Enter>.
4. At the Main Menu, type 2 then press <Enter>. The Update BIOS Including Boot Block and ESCD screen appears.
5. Type the filename of your new BIOS and the path, for example, A:\XXX-XX.XXX, then press <Enter>.
To cancel this operation, press <Enter>.
6. When prompted to confirm the BIOS update, press Y to start the update.
ASUS PRL-DLS533 motherboard user guide
4-3
Page 71
7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary. This minimizes the possibility of boot problems in case of update failures. When the programming is done, the message “Flashed Successfully” appears.
8. Follow the onscreen instructions to continue.
4-4
If you encounter problems while updating the new BIOS, DO NOT turn off the system because this may cause boot problems. Just repeat the process, and if the problem persists, load the original BIOS file you saved to the boot disk. If the Flash Memory Writer utility is not able to successfully update a complete BIOS file, the system may not boot. If this happens, call the ASUS service center for support.
Chapter 4: BIOS Setup
Page 72
4.2 BIOS Setup program
This motherboard supports a programmable Flash ROM that you can update using the provided utility described in section 4.1 Managing and updating your BIOS.”
Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility.
Even if you are not prompted to use the Setup program, you may want to change the configuration of your computer in the future. For example, you may want to enable the security password feature or make changes to the power management settings. This requires you to reconfigure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the Flash ROM.
The Flash ROM on the motherboard stores the Setup utility. When you start up the computer, the system provides you with the opportunity to run this program. Press <Delete> during the Power-On Self Test (POST) to enter the Setup utility, otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing <Ctrl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You can also restart by turning the system off and then back on. Do this last option only if the first two failed.
The Setup program is designed to make it as easy to use as possible. It is a menu-driven program, which means you can scroll through the various sub-menus and make your selections among the predetermined choices.
Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purposes only, and may not exactly match what you see on your screen.
ASUS PRL-DLS533 motherboard user guide
4-5
Page 73
4.2.1 BIOS menu bar
The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system
configuration.
ADVANCED Use this menu to enable and make changes to the
advanced features.
POWER Use this menu to configure power management features. BOOT Use this menu to configure the default system device used
to locate and load the Operating System.
SERVER Use this menu to set server-related items EXIT Use this menu to exit the current menu or to exit the Setup
program.
To access the menu bar items, press the right or left arrow key on the keyboard until the desired item is highlighted.
4.2.2 Legend bar
At the bottom of the Setup screen is a legend bar . The keys in the legend bar allow you to navigate through the various setup menus. The following table lists the keys found in the legend bar with their corresponding functions.
Navigation Key(s) Function Description
<F1> or <Alt + H> Displays the General Help screen from any-
where in the BIOS Setup
<Esc> Jumps to the Exit menu or returns to the main
menu from a sub-menu
Left or Right arrow Selects the menu item to the left or right Up or Down arrow Moves the highlight up or down between fields
- (minus key) Scrolls backward through the values for the
highlighted field
+ (plus key) or spacebar Scrolls forward through the values for the high-
lighted field
<Enter> Brings up a selection menu for the highlighted
field
<Home> or <PgUp> Moves the cursor to the first field <End> or <PgDn> Moves the cursor to the last field <F5> Resets the current screen to its Setup Defaults <F10> Saves changes and exits Setup
4-6
Chapter 4: BIOS Setup
Page 74
General help
In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. You may launch this screen from any menu by simply pressing <F1> or the <Alt> + <H> combination. The General Help screen lists the legend keys and their corresponding functions.
Saving changes and exiting the Setup program
See 4.8 Exit Menu” for detailed information on saving changes and exiting the setup program.
Scroll bar
When a scroll bar appears to the right of a help window, it indicates that there is more information to be displayed that will not fit in the window. Use <PgUp> and <PgDn> or the up and down arrow keys to scroll through the entire help document. Press <Home> to display the first page, press <End> to go to the last page. To exit the help window, press <Enter> or <Esc>.
Sub-menu
Note that a right pointer symbol (as shown on the left) appears to the left of certain fields. This pointer indicates that you can display a sub-menu from this field. A sub-menu contains additional options for a field parameter. To display a sub-menu, move the highlight to the field and press <Enter>. The sub­menu appears. Use the legend keys to enter values and move from field to field within a sub-menu as you would within a menu. Use the <Esc> key to return to the main menu.
Take some time to familiarize yourself with the legend keys and their corresponding functions. Practice navigating through the various menus and sub-menus. If you accidentally make unwanted changes to any of the fields, use the set default hot key <F5> to load the Setup default values. While moving around through the Setup program, note that explanations appear in the Item Specific Help window located to the right of each menu. This window displays the help text for the currently highlighted field.
ASUS PRL-DLS533 motherboard user guide
4-7
Page 75
4.3 Main Menu
When you enter the Setup program, the following screen appears.
System Time [XX:XX:XX]
Sets the system to the time that you specify (usually the current time). The format is hour, minute, second. Valid values for hour, minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the <Tab> or <Shift> + <Tab> keys to move between the hour, minute, and second fields.
System Date [XX/XX/XXXX]
Sets the system to the date that you specify (usually the current date). The format is month, day, year. Valid values for month, day, and year are Month: (1 to 12), Day: (1 to 31), Year: (up to 2099). Use the <Tab> or <Shift> + <Tab> keys to move between the month, day, and year fields.
Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of floppy drive installed. Configuration options: [None] [360K,
5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.] [2.88M, 3.5 in.]
Floppy 3 Mode Support [Disabled]
This is required to support older Japanese floppy drives. The Floppy 3 Mode feature allows reading and writing of 1.2MB (as opposed to 1.44MB) on a 3.5-inch diskette. Configuration options: [Disabled] [Enabled]
4-8
Chapter 4: BIOS Setup
Page 76
Supervisor Password [Disabled] / User Password [Disabled]
These fields allow you to set passwords. To set a password, highlight the appropriate field and press <Enter>. Type in a password then press <Enter>. You can type up to eight alphanumeric characters. Symbols and other characters are ignored. To confirm the password, type the password again and press <Enter>. The password is now set to [Enabled]. This password allows full access to the BIOS Setup menus. To clear the password, highlight this field and press <Enter>. The same dialog box as above appears. Press <Enter>. The password is set to [Disabled].
A note about passwords
The BIOS Setup program allows you to specify passwords in the Main menu. The passwords control access to the BIOS during system startup. Passwords are not case sensitive, meaning, passwords typed in either uppercase or lowercase letters are accepted. The BIOS Setup program allows you to specify two different passwords: a Supervisor password and a User password. If you did not set a Supervisor password, anyone can access the BIOS Setup program. If you did, the Supervisor password is required to enter the BIOS Setup program and to gain full access to the configuration fields.
Forgot the password?
If you forget your password, you can clear it by erasing the CMOS Real Time Clock (RTC) RAM. The RAM data containing the password information is powered by the onboard button cell battery. See section “2.7Switches and jumpers” for information on how to erase the R TC RAM.
Halt On [All Errors]
This field specifies the types of errors that will cause the system to halt. Configuration options: [All Errors] [No Error] [All but Keyboard] [All but Disk] [All but Disk/Keyboard]
Installed Memory [XXX MB]
This field automatically displays the amount of conventional memory detected by the system during the boot process.
ASUS PRL-DLS533 motherboard user guide
4-9
Page 77
4.3.1 Primary/Secondary/Tertiary Master/Slave
Type [Auto]
Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu. If automatic detection fails, this may be because the hard disk drive is too old or too new. If the hard disk was already formatted on an older system, Setup may detect incorrect parameters. In these cases, select [User Type HDD] to manually enter the IDE hard disk drive parameters. Refer to the next section for details.
Before attempting to configure a hard disk drive, make sure you have the correct configuration information supplied by the drive manufacturer. Incorrect settings may cause the system to fail to recognize the installed hard disk.
4-10
Chapter 4: BIOS Setup
Page 78
[User Type HDD]
Manually enter the number of cylinders, heads and sectors per track for the drive. Refer to the drive documentation or on the drive label for this information.
After entering the IDE hard disk drive information into BIOS, use a disk utility, such as FDISK, to partition and format new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk. Make sure to set the partition of the Primary IDE hard disk drives to active.
If no drive is installed or if you are removing a drive and not replacing it, select [None].
Other options for the Type field are:
[CD-ROM] - for IDE CD-ROM drives [LS-120] - for LS-120 compatible floppy disk drives [ZIP] - for ZIP-compatible disk drives [MO] - for IDE magneto optical disk drives [Other A TAPI Device] - for IDE devices not listed here
After making your selections on this sub-menu, press the <Esc> key to return to the Main menu. When the Main menu appears, the hard disk drive field displays the size for the hard disk drive that you configured.
ASUS PRL-DLS533 motherboard user guide
4-11
Page 79
Translation Method [LBA]
Select the hard disk drive type in this field. When Logical Block Addressing (LBA) is enabled, the 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors. Note that LBA Mode is necessary for drives with more than 504MB storage capacity. Configuration options: [LBA] [LARGE] [Normal] [Match Partition Table] [Manual]
Cylinders
This field configures the number of cylinders. Refer to the drive documentation to determine the correct value. To make changes to this field, set the Type field to [User Type HDD] and the Translation Method field to [Manual].
Head
This field configures the number of read/write heads. Refer to the drive documentation to determine the correct value. To make changes to this field, set the Type field to [User Type HDD] and the Translation Method field to [Manual].
Sector
This field configures the number of sectors per track. Refer to the drive documentation to determine the correct value. To make changes to this field, set the Type field to [User Type HDD] and the Translation Method field to [Manual].
CHS Capacity
This field shows the drive’s maximum CHS capacity as calculated by the BIOS based on the drive information you entered.
Maximum LBA Capacity
This field shows the drive’s maximum LBA capacity as calculated by the BIOS based on the drive information you entered.
Multi-Sector Transfers [Maximum]
This option automatically sets the number of sectors per block to the highest number that the drive supports. Note that when this field is automatically configured, the set value may not always be the fastest value for the drive. You may also manually configure this field. Refer to the documentation that came with the hard drive to determine the optimum value and set it manually. To make changes to this field, set the Type field to [User Type HDD]. Configuration options: [Disabled] [2 Sectors] [4 Sectors] [8 Sectors] [16 Sectors] [32 Sectors] [Maximum]
4-12
Chapter 4: BIOS Setup
Page 80
SMART Monitoring [Disabled]
This field allows you to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) system that utilizes internal hard disk drive monitoring technology. This parameter is normally disabled because the resources used in the SMART monitoring feature may decrease system performance. Configuration options: [Disabled] [Enabled]
PIO Mode [4]
This option lets you set a PIO (Programmed Input/Output) mode for the IDE device. Modes 0 through 4 provide successive increase in performance. Configuration options: [0] [1] [2] [3] [4]
Ultra DMA Mode [Disabled]
Ultra DMA capability allows improved transfer speeds and data integrity for compatible IDE devices. Set to [Disabled] to suppress Ultra DMA capability. To make changes to this field, set the Type field to [User Type HDD]. Configuration options: [0] [1] [2] [3] [4] [5] [Disabled]
ASUS PRL-DLS533 motherboard user guide
4-13
Page 81
4.3.2 Keyboard Features
Boot Up NumLock Status [On]
This field enables users to activate the Number Lock function upon system boot. Configuration options: [Off] [On]
Keyboard Auto-Repeat Rate [6/Sec]
This controls the speed at which the system registers repeated keystrokes. Options range from 6 to 30 characters per second. Configuration options: [6/Sec] [8/Sec] [10/Sec] [12/Sec] [15/Sec] [20/Sec] [24/Sec] [30/Sec]
Keyboard Auto-Repeat Delay [1/4 Sec]
This field sets the time interval for displaying the first and second characters. Configuration options: [1/4 Sec] [1/2 Sec] [3/4 Sec] [1 Sec]
4-14
Chapter 4: BIOS Setup
Page 82
4.4 Advanced Menu
CPU Speed [Manual]
This field displays the auto-detected CPU speed.
CPU Level 1 Cache, CPU Level 2 Cache [Enabled]
These fields allow you to choose from the default [Enabled] or choose [Disabled] to turn on or off the CPU Level 1 and Level 2 built-in cache. Configuration options: [Disabled] [Enabled]
Hyper-Threading Technology [Enabled]
This item allows you to enable or disable support for Hyper-Threading Technology enabled processors which contain multiple logical processors per physical processor package. Configuration options: [Disabled] [Enabled]
BIOS Update [Enabled]
This field functions as an update loader integrated into the BIOS to supply the processor with the required data. When set to [Enabled], the BIOS loads the update on all processors during system bootup. Configuration options: [Disabled] [Enabled]
PS/2 Mouse Function Control [Auto]
The default setting [Auto] allows the system to detect a PS/2 mouse at startup. If a mouse is detected, the BIOS assigns IRQ12 to the PS/2 mouse. Otherwise, IRQ12 can be used for expansion cards. When you set this field to [Enabled], BIOS reserves IRQ12, whether or not a PS/2 mouse is detected at startup. Configuration options: [Enabled] [Auto]
ASUS PRL-DLS533 motherboard user guide
4-15
Page 83
OS/2 Onboard Memory > 64M [Disabled]
When using OS/2 operating systems with installed DRAM of greater than 64MB, you need to set this option to [Enabled]. Otherwise, leave to the default setting [Disabled]. Configuration options: [Disabled] [Enabled]
USB Legacy Support [Auto]
This motherboard supports Universal Serial Bus (USB) devices. The default of [Auto] allows the system to detect a USB device at startup. If detected, the USB controller legacy mode is enabled. If not detected, the USB controller legacy mode is disabled.
When you set this field to [Disabled], the USB controller legacy mode is disabled whether or not you are using a USB device. Configuration options: [Disabled] [Enabled] [Auto]
4-16
Chapter 4: BIOS Setup
Page 84
4.4.1 Chip Configuration
Video Memory Cache Mode [UC]
USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor. It can greatly improve the display speed by caching the display data. You must set this to UC (uncacheable) if your display card cannot support this feature; otherwise your system may not boot. Configuration options: [UC] [USWC]
Onboard PCI IDE [All]
You can select to enable the primary, secondary, tertiary IDE channel, all channels, or disable all channels. Configuration options: [All] [Primary\Secondary] [Primary\Tertiary] [Primary] [Secondary\Tertiary\ [Secondary] [Tertiary] [Disabled]
DDR DQS Delay TAP in DEC [5]
Default setting is 5. User settings are from 0 to 96. The last setting, 96, is for auto selection. Configuration options: [0...96]
ASUS PRL-DLS533 motherboard user guide
4-17
Page 85
4.4.2 I/O Device Configuration
Floppy Disk Access Control [R/W]
When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive. The default setting [R/W] allows both reads and writes. Configuration options: [R/W] [Read Only]
Onboard Serial Port 1 [3F8H/IRQ4] Onboard Serial Port 2 [2F8H/IRQ3]
These fields allow you to set the addresses for the onboard serial connectors. Serial Port 1 and Serial Port 2 must have different addresses. Configuration options: [3F8H/IRQ4] [2F8H/IRQ3] [3E8H/IRQ4] [2E8H/ IRQ10] [Disabled]
Onboard Parallel Port [378H/IRQ7]
This field allows you to set the address of the onboard parallel port connector . If you disable this field, the Parallel Port Mode and ECP DMA Select configurations are not available. Configuration options: [Disabled] [378H/IRQ7] [278H/IRQ5]
4-18
Chapter 4: BIOS Setup
Page 86
Parallel Port Mode [ECP+EPP]
This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction only; [EPP] allows bidirectional parallel port operation; [ECP] allows the parallel port to operate in bidirectional DMA mode; [ECP+EPP] allows normal speed operation in a two-way mode. Configuration options: [Normal] [EPP] [ECP] [ECP+EPP]
ECP DMA Select [3]
This field allows you to configure the parallel port DMA channel for the selected ECP mode. This selection is available only if you select [ECP] or [ECP+EPP] in Parallel Port Mode above. Configuration options: [1] [3]
ASUS PRL-DLS533 motherboard user guide
4-19
Page 87
4.4.3 PCI Configuration
Slot 1, Slot 2, Slot 3, Slot 4, Slot 5, Slot 6 IRQ [Auto]
These fields set how IRQ use is determined for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ use. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [11] [12] [14] [15]
PCI/VGA Palette Snoop [Disabled]
Some non-standard VGA cards, like graphics accelerators or MPEG video cards, may not show colors properly. Setting this field to [Enabled] corrects this problem. If you are using standard VGA cards, leave this field to the default setting [Disabled]. Configuration options: [Disabled] [Enabled]
PCI Latency Timer [32]
Leave on default setting for best performance vs. stability.
Sparse PCI Host Bus [3 BUS]
This field allows you to reserve the bus number for the PCI slots. Configuration options: [Disabled] [2 BUS] [3 BUS] [4 BUS]
4-20
Chapter 4: BIOS Setup
Page 88
Onboard SCSI BIOS [Auto]
[Auto] allows the motherboard BIOS to detect whether you have a LSI SCSI controller. If the SCSI controller is detected, the SCSI BIOS will be enabled. If no SCSI controller is detected, the onboard SCSI BIOS will be disabled.
Setting to [Disabled] deactivates the onboard SCSI BIOS so that the BIOS on an add-on SCSI card can be used. If your SCSI card does not have a BIOS, the SCSI card will not function. Configuration options: [Auto] [Disabled]
Primary VGA BIOS First [PCI VGA Card]
This field allows you to select the primary graphics card. Configuration options: [PCI VGA Card] [Onboard VGA]
USB Function [Enabled]
Set this field to [Enabled] if you want to use Universal Serial Bus devices. Configuration options: [Disabled] [Enabled]
Onboard LAN Boot ROM [Disabled] Onboard 2nd LAN Boot ROM [Disabled]
When set to [Enabled], these fields allow the system to boot from the network using the onboard LAN controller boot ROM. Configuration options: [Disabled] [Enabled]
ASUS PRL-DLS533 motherboard user guide
4-21
Page 89
4.5 Power Menu
The Power menu allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity.
Power Management [User Defined]
This field allows you to activate or deactivate the automatic power saving features. When set to [Disabled], the power management features do not function regardless of the other settings on this menu. The [User Defined] option allows you to set the period of inactivity before the system enters suspend mode. Refer to “Suspend Mode” item.
When set to [Max Saving], system power is conserved to its greatest amount. This setting automatically puts the system into suspend mode after a brief period of system inactivity. [Min Saving] allows the least power saving as the system enters suspend mode only after a long period of inactivity. Configuration options: [User Defined] [Disabled] [Min Saving] [Max Saving]
You should install the Advanced Power Management (APM) utility to keep the system time updated even when the computer enters suspend mode. In Windows 3.x and Windows 95, you need to install Windows with the APM feature. In Windows 98 or later, APM is automatically installed as indicated by a battery and power cord icon labeled “Power Management” in the Control Panel. Select the item “Advanced” in the Power Management Properties dialog box.
4-22
Chapter 4: BIOS Setup
Page 90
Video Off Option [Suspend -> Off ]
This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off]
Video Off Method [DPMS OFF]
This field defines the video off features. The Display Power Management System (DPMS) feature allows the BIOS to control the video display card if it supports the DPMS feature. [Blank Screen] only blanks the screen. Use this for monitors without power management or “green” features.
Even if installed, your screen saver does not display when you select [Blank Screen] for the above field.
[V/H SYNC+Blank] blanks the screen and turns off vertical and horizontal scanning. Configuration options: [Blank Screen] [V/H SYNC+Blank] [DPMS Standby] [DPMS Suspend] [DPMS OFF] [DPMS Reduce ON]
HDD Power Down [Disabled]
Shuts down any IDE hard disk drives in the system after a period of inactivity as set in this user-configurable field. This feature does not affect SCSI hard drives. Configuration options: [Disabled] [1 Min] [2 Min] [3 Min]...[15 Min]
Suspend Mode [Disabled]
Sets the time period before the system goes into suspend mode. Configuration options: [Disabled] [1~2 Min] [2~3 Min] [4~5 min] [8~9 Min] [20 Min] [30 Min] [40 Min] [1 Hour]
PWR Button < 4 Secs [Soft Off]
When set to [Soft off], the ATX switch can be used as a normal system power-off button when pressed for less than 4 seconds. [Suspend] allows the button to have a dual function where pressing less than 4 seconds puts the system in sleep mode. Regardless of the setting, holding the ATX switch for more than 4 seconds powers off the system. Configuration options: [Soft off] [Suspend]
ASUS PRL-DLS533 motherboard user guide
4-23
Page 91
4.5.1 Power Up Control
AC PWR Loss Restart [Disabled]
This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off while [Enabled] reboots the system. [Previous State] sets the system back to the state it was before the power interruption. Configuration options: [Disabled] [Enabled] [Previous State]
Wake/Power Up On Ext. Modem [Disabled]
This allows either settings of [Enabled] or [Disabled] for powering up the computer when the external modem receives a call while the computer is in Soft-off mode. Configuration options: [Disabled] [Enabled]
The computer cannot receive or transmit data until the computer and applications are fully running. Thus, connection cannot be made on the first try. Turning an external modem off and then back on while the computer is off causes an initialization string that turns the system power on.
Onboard LAN Power Up [Disabled] Power Up on PCI Card [Disabled]
These fields allow you to boot your computer from another computer by sending a wake-up frame or signal to the LAN device, or the PCI modem card if present. Configuration options: [Disabled] [Enabled]
4-24
Chapter 4: BIOS Setup
Page 92
Power On By PS/2 Keyboard [Disabled]
This parameter allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key]
Automatic Power Up [Disabled]
This allows an unattended or automatic system power up. You may configure your system to power up at a certain time of the day by selecting [Everyday] or at a certain time and day by selecting [By Date]. Configuration options: [Disabled] [Everyday] [By Date]
ASUS PRL-DLS533 motherboard user guide
4-25
Page 93
4.5.2 Hardware Monitor
MB Temperature [xxxC/xxxF], CPU1 Temperature [xxxC/xxxF], CPU2 Temperature [xxxC/xxxF]
The onboard hardware monitor is able to detect the MB (motherboard) and CPU temperatures. Set to [Ignore] only if necessary.
CPU1 Fan Speed [xxxxRPM], CPU2 Fan Speed [xxxxRPM], System Fan Speed [xxxxRPM]
The onboard hardware monitor is able to detect the CPU fan speeds in rotations per minute (RPM). The presence of the fans is automatically detected.
VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage Voltage
The onboard hardware monitor is able to detect the voltage output by the onboard voltage regulators.
If any of the monitored items is out of range, the following error message appears: “Hardware Monitor found an error. Enter Power setup menu for details”. You will then be prompted to “Press F1 to continue or DEL to enter SETUP”.
, 3VSB
4-26
Chapter 4: BIOS Setup
Page 94
4.6 Boot Menu
The motherboard BIOS supports the BIOS Boot Specification (BBS) version 1.01. BBS is an intelligent mechanism that provides flexible ways to set boot sequence for Initial Program Load (IPL) devices such as CD-ROMs, network remote boot ROM, and SCSI or RAID controllers on PnP cards.
The IPL devices are classified into three categories:
BIOS Aware IPL Devices (BAID)
Legacy devices
PnP devices, includes Boot Connection Vector (BCV) and Bootstrap Entry Vector (BEV) devices
ASUS PRL-DLS533 motherboard user guide
4-27
Page 95
1st Boot : (BAID) [None]
This field allows you to select a BIOS Aware IPL Devices (BAID) to boot from. A BAID is any device that can boot on an operating system but requires a specific BIOS code for support. Bootable FDDs, ATA HDD, ATAPI CD-ROM, ATA ZIP, and ATA MO drives are classified as BAID. The drives present in the system will appear as options for this field.
2nd Boot : (Legacy) [Disabled]
This field reserves the boot sequence selection only to legacy devices including FDD, HDD, CD-ROM, SCSI, and LAN. This mode does not allow booting from a boot device on an add-on card or controller. If you wish to assign a device as a 1st Boot device for a specific application, you must set that legacy device at the 1st Boot sequence.
For this motherboard, the following options are present onboard: [Disabled] [Floppy] [HDD] [CD-ROM] [LAN Option ROM] [SCSI]
3rd Boot : (BCV) [None]
This field allows you to select a Boot Connection Vector (BCV) device to boot from. BCV devices include SCSI controllers or SCSI cards, RAID cards, and other devices on add-on cards with option ROM that hooks INT 13 to BIOS. The BCV devices present in the system will appear as options for this field. The field shows [None] if no BCV device is installed.
Some SCSI RAID cards hook INT 19 to BIOS. If you use these cards, you should enable INT 19 after installing the card. Otherwise, you will not be able to enter the RAID card BIOS.
4th Boot : (BEV) [<0> Intel Corporation]
This field allows you to select a Bootstrap Entry Vector (BEV) device to boot from. BEV devices include network controllers or cards. The BEV devices present in the system will appear as options for this field. For this motherboard, the following options are present onboard: [None]
Plug & Play O/S [No]
This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Yes] is selected, interrupts may be reassigned by the OS. If you installed a non­PnP OS or if you want to prevent reassigning of interrupt settings, keep the default setting [No]. Configuration options: [No] [Yes]
4-28
Chapter 4: BIOS Setup
Page 96
Reset Configuration Data [No]
The Extended System Configuration Data (ESCD) contain information about non-PnP devices. It also holds the complete record of how the system was configured the last time it was booted. Select [Yes] if you want to clear these data during the Power-On-Self-Test (POST). Configuration options: [No] [Yes]
MPS 1.4 Support [Enabled]
This field allows you to enable or disable the MultiProcessor Specification
1.4 support. Configuration options: [Disabled] [Enabled]
Quick Power On Self Test [Enabled]
This field speeds up the Power-On-Self Test (POST) routine by skipping retesting a second, third, and fourth time. Configuration options: [Disabled] [Enabled]
Boot Up Floppy Seek [Enabled]
When enabled, the BIOS will seek the floppy disk drive to determine whether the drive has 40 or 80 tracks. Configuration options: [Disabled] [Enabled]
Post Diag [Disabled]
Configuration options: [Disabled] [Enabled]
ASUS PRL-DLS533 motherboard user guide
4-29
Page 97
4.6.1 Slot Configuration
Init Slot 1, 2, 3, 4, 5, 6 IRQ [Normal]
This field allows you to set the priority level for each expansion slot in order to determine expansion card initialization order. Configuration options: [High] [Normal] [Low] [Skip]
4-30
Chapter 4: BIOS Setup
Page 98
4.7 Server Menu
Remote Console [Disabled]
This field allows the text mode VGA display to be sent out to VT100 terminal through COM1. This function is effective at BIOS POST and DOS environment. Configuration options: [Disabled] [Enabled] [POST Only]
Event Log Viewer
Pressing <Enter> on this item gives you a sub-menu. You will be shown all events such as “no bootable media” or “fan speed out of range”.
Clear Event Log [Disabled]
This field clears the event log recorded on the sub-menu. Select [Enabled] to automatically clear the event log. Reset to [Disabled] to store up event log data. An IPMI device must be connected to the server for this field to function. Configuration options: [Disabled] [Enabled]
Log Memory ECC Error [Enabled]
This field allows you to set whether “Error Checking and Correcting” memory errors are logged. Configuration options: [Disabled] [Enabled]
Side 0 of DIMM0 -- Side 1 of DIMM3 [Enabled]
This field displays the presence of ECC DIMMS in the slots. Installed DIMMs automatically display [Enabled]. If the DIMM slot is empty, the gray “Not Installed” message is displayed. Configuration options: [Enabled] Not Installed.
ASUS PRL-DLS533 motherboard user guide
4-31
Page 99
4.7.1 Event Log V iewer
No IPMI Device Detected
Unless an IPMI device, like the ASMC-LE/HE server management card is installed, the Event Log Viewer will not display any data. If installed, a detailed range of server data is displayed.
4-32
Chapter 4: BIOS Setup
Page 100
4.8 Exit Menu
When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup. Select Exit from the menu bar to display the following menu.
Pressing <Esc> does not immediately exit this menu. Select one of the options from this menu or <F10> from the legend bar to exit.
Exit Saving Changes
Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select [Yes] to save changes and exit.
If you attempt to exit the Setup program without saving your changes, the program prompts you with a message asking if you want to save your changes before exiting. Pressing <Enter> saves the changes while exiting.
Exit Discarding Changes
Select this option only if you do not want to save the changes that you made to the Setup program. If you made changes to fields other than system date, system time, and password, the BIOS asks for a confirmation before exiting.
ASUS PRL-DLS533 motherboard user guide
4-33
Loading...