ASUS L1N64-SLI WS User Manual
L1N64-SLI WS
Motherboard
E3014
Second Edition V2
December 2006
Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
ii
Contents
Notices ........................................................................................................ vii
Safety information .................................................................................... viii
About this guide ......................................................................................... ix
L1N64-SLI WS specications summary ................................................... xi
Chapter 1: Product introduction
1.1 Welcome! ...................................................................................... 1-1
1.2 Special features ............................................................................
1.2.1 Product highlights ...........................................................
1.2.2 ASUS Special features ...................................................
Chapter 2: Hardware information
2.1 Before you proceed ..................................................................... 2-1
2.2 Motherboard overview .................................................................
2.2.1 Placement direction ........................................................
2.2.2 Screw holes ....................................................................
2.2.3 Motherboard layout .........................................................
2.2.4 Layout contents ...............................................................
2.3 Central Processing Unit (CPU) ...................................................
2.3.1 Installing the CPU ...........................................................
2.3.2 Installing the heatsink and fan ........................................
2.3.3 Installing the fan ............................................................
2.4 System memory .........................................................................
2.4.1 Overview .......................................................................
2.4.2 Memory congurations ..................................................
2.4.3 Installing a DIMM ..........................................................
2.4.4 Removing a DIMM ........................................................
2.5 Expansion slots ..........................................................................
2.5.1 Installing an expansion card .........................................
2.5.2 Conguring an expansion card .....................................
2.5.3 Interrupt assignments ...................................................
2.5.4 PCI slot .........................................................................
2.5.5 PCI Express x1 slot .......................................................
2.5.6 Four PCI Express x16 slots ..........................................
1-2
1-2
1-4
2-2
2-2
2-2
2-3
2-4
2-6
2-6
2-9
2-12
2-13
2-13
2-14
2-15
2-15
2-16
2-16
2-16
2-17
2-18
2-18
2-18
iii
Contents
2.6 Jumper ........................................................................................ 2-20
2.7 Connectors .................................................................................
2.7.1 Rear panel connectors ..................................................
2.7.2 Internal connectors .......................................................
Chapter 3: Powering up
3.1 Starting up for the rst time ........................................................ 3-1
3.2 Powering off the computer ..........................................................
3.2.1 Using the OS shut down function ....................................
3.2.2 Using the dual function power switch ..............................
Chapter 4: BIOS setup
4.1 Managing and updating your BIOS ............................................ 4-1
4.1.1 ASUS Update utility ........................................................
4.1.2 Creating a bootable oppy disk .......................................
4.1.3 AFUDOS utility ................................................................
4.1.4 ASUS CrashFree BIOS 3 utility ......................................
4.2 BIOS setup program ....................................................................
4.2.1 BIOS menu screen ........................................................
4.2.2 Menu bar .......................................................................
4.2.3 Navigation keys .............................................................
4.2.4 Menu items ....................................................................
4.2.5 Sub-menu items .............................................................
4.2.6 Conguration elds ........................................................
4.2.7 Pop-up window ..............................................................
4.2.8 Scroll bar ........................................................................
4.2.9 General help ..................................................................
4.3 Main menu ..................................................................................
4.3.1 System Time .................................................................
4.3.2 System Date .................................................................
4.3.3 Legacy Diskette A .........................................................
4.3.4 Language ......................................................................
4.3.5 Primary IDE Master/Slave .............................................
4.3.6 SATA 1-12 .....................................................................
4.3.7 IDE Conguration ..........................................................
4.3.8 System Information .......................................................
2-21
2-21
2-23
3-2
3-2
3-2
4-1
4-4
4-5
4-8
4-9
4-10
4-10
4-10
4-11
4-11
4-11
4-11
4-11
4-11
4-12
4-12
4-12
4-12
4-12
4-13
4-14
4-15
4-16
iv
Contents
4.4 Advanced menu ......................................................................... 4-17
4.4.1 JumperFree Conguration ............................................
4.4.2 CPU Conguration ........................................................
4.4.3 Chipset ..........................................................................
4.4.4 Onboard Devices Conguration ....................................
4.4.5 PCI PnP ........................................................................
4.4.6 USB Conguration ........................................................
4.5 Power menu ................................................................................
4.5.1 Suspend Mode [Auto] ...................................................
4.5.2 ACPI 2.0 Support ..........................................................
4.5.3 ACPI APIC Support .......................................................
4.5.4 APM Conguration ........................................................
4.5.5 Hardware Monitor .........................................................
4.6 Boot menu ..................................................................................
4.6.1 Boot Device Priority ......................................................
4.6.2 Boot Settings Conguration ..........................................
4.6.3 Security .........................................................................
4.7 Exit menu ....................................................................................
Chapter 5: Software support
5.1 Installing an operating system ................................................... 5-1
5.2 Support CD information ..............................................................
5.2.1 Running the support CD .................................................
5.2.2 Drivers menu ...................................................................
5.2.3 Utilities menu ..................................................................
5.2.4 Make Disk menu .............................................................
5.2.5 Manuals menu ................................................................
5.2.6 ASUS Contact information ..............................................
5.2.7 Other information ............................................................
4-17
4-21
4-22
4-25
4-27
4-28
4-29
4-29
4-29
4-29
4-30
4-32
4-34
4-34
4-35
4-36
4-39
5-1
5-1
5-2
5-3
5-4
5-5
5-5
5-6
v
Contents
Chapter 5: Software support
5.1 Installing an operating system ................................................... 5-1
5.2 Support CD information ..............................................................
5.2.1 Running the support CD .................................................
5.2.2 Drivers menu ...................................................................
5.2.3 Utilities menu ..................................................................
5.2.4 Make Disk menu .............................................................
5.2.5 Manuals menu ................................................................
5.2.6 ASUS Contact information ..............................................
5.2.7 Other information ............................................................
5-1
5-1
5-2
5-3
5-5
5-6
5-7
5-7
vi
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
This device may not cause harmful interference, and
•
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
vii
Safety information
Electrical safety
•
To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
•
When adding or removing devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are
connected. If possible, disconnect all power cables from the existing system
before you add a device.
•
Before connecting or removing signal cables from the motherboard, ensure
that all power cables are unplugged.
•
Seek professional assistance before using an adpater or extension cord.
These devices could interrupt the grounding circuit.
•
Make sure that your power supply is set to the correct voltage in your area.
If you are not sure about the voltage of the electrical outlet you are using,
contact your local power company.
•
If the power supply is broken, do not try to x it by yourself. Contact a
qualied service technician or your retailer.
Operation safety
•
Before installing the motherboard and adding devices on it, carefully read all
the manuals that came with the package.
•
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
•
Avoid dust, humidity, and temperature extremes. Do not place the product in
any area where it may become wet.
•
Place the product on a stable surface.
•
If you encounter technical problems with the product, contact a qualied
service technician or your retailer.
viii
About this guide
This user guide contains the information you need when installing and conguring
the motherboard.
How this guide is organized
This guide contains the following parts:
• Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new
technology it supports.
• Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to perform
when installing system components. It includes description of the switches,
jumpers, and connectors on the motherboard.
• Chapter 3: Powering up
This chapter describes the power up sequence and ways of shutting down
the system.
• Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
• Chapter 5: Software support
This chapter describes the contents of the support CD that comes with the
motherboard package.
Where to nd more information
Refer to the following sources for additional information and for product and
software updates.
1. ASUS websites
The ASUS website provides updated information on ASUS hardware and
software products. Refer to the ASUS contact information.
2. Optional documentation
Your product package may include optional documentation, such as warranty
yers, that may have been added by your dealer. These documents are not
part of the standard package.
ix
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following
symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself
when trying to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a
task.
Typography
Bold text Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the
Enter or Return key.
<Key1+Key2+Key3> If you must press two or more keys simultaneously, the
key names are linked with a plus sign (+).
Example: <Ctrl+Alt+D>
Command Means that you must type the command exactly
as shown, then supply the required item or value
enclosed in brackets.
Example: At the DOS prompt, type the command line:
afudos /i[lename]
afudos /iL1N64WS.ROM
x
L1N64-SLI WS specications summary
CPU Supports 2 AMD Atholon™ 64FX Socket L1 (1207FX)
Chipset 2 x NVIDIA® MCP55PXE
System bus 2000 / 1600 MT/s
Memory Dual-channel memory architecture
Expansion slots 4 x PCI Express™ x16 slots (at x16, x8, x16, x8)
Scalable Link Interface
(SLI™)
Storage 2x NVIDIA® MCP55PXE supports:
LAN 2 x Marvell® 88E1116 PHY support:
High Denition Audio SoundMAX® ADI AD1988B 8-channel High Denition
IEEE 1394 VIA 6308P 1394 controller supports:
USB Supports up to 10 USB 2.0/1.1 ports
CPU
Supports AMD Cool ‘n’ Quiet™ Technology
AMD64 architecture enables simultaneous 32-bit and
64-bit computing
- 4 x 240-pin DIMM sockets support unbufferred
ECC/non-ECC DDR2 800/667/533/400 MHz
memory modules
- Supports up to 8 GB system memory
1 x PCI-E x1 slot
1 x PCI 2.2 slot
Supports two identical NVIDIA® SLI™-ready graphics
cards
- 1 x IDE connector for up to two Ultra DMA
133/100 devices
- 12 x Serial ATA 3.0 Gb/s connectors support twelve
Serial ATA devices
- RAID 0, RAID1, RAID 0+1, RAID 5, and JBOD
congurations spanning across Serial ATA drives
via the onboard NVIDIA® MediaShield™ RAID
controller
Silicon Image® Sil3531 Serial ATA controller supports:
- 1 x External Serial ATA 3.0 Gb/s on the rear panel
Gigabit LAN
Firewall function
Supports Teaming functions
Wake up from S5
Audio CODEC
Supports Jack-Sensing, Enumeration, Multi-Streaming,
and Jack-Retasking Technology
Optical and Coaxial S/PDIF Out interfaces at the rear
panel
- 2 x IEEE 1394a connectors
(continued on the next page)
xi
L1N64-SLI WS specications summary
ASUS special features
Performance
ASUS special features
Thermal
ASUS special features
Life
Rear panel 1 x PS/2 keyboard port (purple)
Internal connectors 3 x USB 2.0 connectors support 6 additional USB 2.0
Intelligent overclocking tools:
- ASUS C.P.R. (CPU Parameter Recall)
- Adjustable FSB/DDR2 ratio. Fixed PCI/PCIe
frequencies.
- Hyper Path 3
Precision Tweaker:
- vDIMM: 25-step DRAM voltage control
- vCore: Adjustable CPU voltage at 0.0125 V
increment
- Stepless Frequency Selection(SFS) allows FSB
tuning from 200 MHz up to 400 MHz at 1 MHz
increment
- PCI Express x16 frequency allows PCI Express x16
frequency tuning from 100 MHz to 150 MHz at 1
MHz increment
ASUS 8-Phase Power Design for each VRM
Q-Fan 2
ASUS Heat-pipe Thermal solution
Multi-language BIOS
SATA on the Go
CrashFree BIOS 3
1 x PS/2 mouse port (green)
1 x Parallel port
1 x External Serial ATA 3.0 Gb/s
1 x Optical S/PDIF Out port
1 x Coaxial S/PDIF Out port
2 x LAN (RJ-45) ports
4 x USB 2.0/1.1 ports
8-channel audio ports
ports
1 x Floppy disk drive connector
1 x IDE connector
12 x Serial ATA connectors
2 x CPU / 4 x Chassis / 1 x Power / 3 x fan connectors
2 x IEEE 1394a connectors
1 x EZ-plug
Chassis intrusion connector
Front panel audio connector
1 x CD audio in connector
1 x TPM connector (optional)
24-pin ATX power connector
8-pin ATX 2.0/1.1 power connector
System panel connector
(continued on the next page)
xii
L1N64-SLI WS specications summary
BIOS features 8 Mb AMI BIOS, PnP, DMI 2.0, WfM2.0, SM BIOS 2.3
Manageability WOL by PME, WOR by PME, PXE, AI NET 2, Chassis
Power requirements ATX power supply (with 24-pin and 4-pin 12 V plugs)
Support CD contents Device drivers
Form factor CEB form factor: 12 in x 10.5 in (30.5 cm x 26.7 cm)
*Specications are subject to change without notice.
Intrusion
ATX 12 V 2.0 compliant
BIOS ash utility under DOS
ASUS PC Probe II
ASUS Update
NVIDIA® RAID
xiii
xiv
This chapter describes the motherboard
features and the new technologies
it supports.
Product
1
introduction
Chapter summary
1
1.1 Welcome! ...................................................................................... 1-1
1.2 Special features ............................................................................
1-2
ASUS L1N64-SLI WS
1.1 Welcome!
Thank you for buying an ASUS® L1N64-SLI WS motherboard!
The motherboard delivers a host of new features and latest technologies, making it
another standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it, check the
items in your package with the list below.
ASUS L1N64-SLI WS 1-1
1.2 Special features
1.2.1 Product highlights
Latest processor technology
The motherboard comes with dual 1207-pin surface mount Land Grid Array
(LGA) sockets coded Socket L1 (1207FX), designed for AMD processors. The
motherboard with the new socket delivers advanced performance and ensuring
reliable data protection. See page 2-6 for details.
AMD Cool ‘n’ Quiet Technology
The motherboard supports the AMD Cool ‘n’ Quiet Technology, which monitors
system operation and automatically adjusts CPU voltage and frequency for a cool
and quiet operating environment. See page 4-18 for details.
NVIDIA® Scalable Link Interface (SLI™)
The NVIDIA® Scalable Link Interface (SLI™) technology allows two graphics
processing units (GPUs) in a single system. This technology takes advantage of
the PCI Express™ bus architecture and features intelligent hardware and software
solutions that allows multiple GPUs to work together and achieve exceptional
graphics performance.
64-bit CPU support
The motherboard supports 64-bit computing, which is the next generation
technology to replace the current 32-bit architecture. The 64-bit architecture
delivers advanced system performance, faster memory access, and increased
productivity. This motherboard provides excellent compatibility and exibility by
support either 64-bit or 32-bit architecture. See page 2-6 for details.
DDR2 memory support
The motherboard supports DDR2 memory that features data transfer rates of
800/667/533/400 MHz to meet the higher bandwidth requirements of the latest
3D graphics, multimedia, and Internet applications. The dual-channel DDR2
architecture doubles the bandwidth of your system memory to boost system
performance, eliminating bottlenecks with peak bandwidths of up to 10.7 GB/s.
See pages 2-13 to 2-14 for details.
1-2 Chapter 1: Product introduction
PCI Express™ interface
The motherboard fully supports PCI Express, the latest I/O interconnect technology
that speeds up the PCI bus. PCI Express features point-to-point serial
interconnections between devices and allows higher clockspeeds by carrying data
in packets. This high speed interface is software compatible with existing PCI
specications. See page 2-18 for details.
Serial ATA I/II technology and SATA-On-The-Go
The motherboard fully supports the Serial ATA II 3.0 Gb/s technology through the
Serial ATA interfaces and the NVIDIA® nForce® 680a SLI™ chipset. The Serial
ATA 3 Gb/s specication provides twice the bandwidth of the current Serial
ATA products with a host of new features, including Power Management (PM)
Implementation Algorithm. Serial ATA allows for thinner, more exible cables with
lower pin count and reduced voltage required. Leveraging these Serial ATA 3.0
Gb/s features is the SATA-On-The-Go. Supported by the Marvell® 88SE614x Serial
ATA controller, four Serial ATA 3.0 Gb/s connectors (three at mid-board and one
on the rear panel) provide smart setup, and hot-plug function. See pages 2-22 and
2-25 for details.
IEEE 1394a support
The IEEE 1394a interface provides high-speed and exible PC connectivity to
a wide range of peripherals and devices compliant to the IEEE 1394a standard.
The IEEE 1394a interface allows up to 400 Mbps transfer rates through simple,
low-cost, high-bandwidth asynchronous (real-time) data interfacing between
computers, peripherals, and consumer electronic devices such as camcorders,
VCRs, printers, TVs, and digital cameras. See page 2-26 for details.
S/PDIF digital sound ready
The motherboard supports the S/PDIF technology through the S/PDIF interfaces
on the rear panel. The S/PDIF technology turns your computer into a high-end
entertainment system with digital connectivity to powerful audio and speaker
systems. See page 2-22 for details.
USB 2.0 technology
The motherboard implements the Universal Serial Bus (USB) 2.0 specication,
dramatically increasing the connection speed from the 12 Mbps bandwidth on USB
1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1.
See pages 2-22 and 2-26 for details.
ASUS L1N64-SLI WS 1-3
Dual Gigabit LAN solution
The motherboard comes with dual Gigabit LAN controllers to provide the total
solution for your networking needs. These network controllers use the PCI Express
segment to provide faster data bandwidth for your wired or wireless Internet, LAN,
and le sharing requirements. See page 2-21 for details.
1.2.2 ASUS Special features
Advanced Thermal Design
8-Phase Power Design
The ASUS 8-Phase Power Design prolongs CPU lifespan and keeps the
system stable by preventing high power stress to the CPU and power supply
module. The design ensures high efciency operation to generate less heat
compared with conventional power solutions, thus achieving cool system
environment and making this motherboard ideal for overclocking.
ASUS CrashFree BIOS 3
The ASUS CrashFree BIOS 3 allows users to restore corrupted BIOS data from a
USB ash disk containing the BIOS le. This utility saves users the cost and hassle
of buying a replacement BIOS chip. See page 4-8 for details.
Precision Tweaker
This feature allows you to ne tune the CPU/memory voltage and gradually
increase the memory Front Side Bus (FSB) and PCI Express frequency at 1MHz
increment to achieve maximum system performance.
ASUS Multi-language BIOS
The multi-language BIOS allows you to select the language of your choice from the
available options. The localized BIOS menus allow easier and faster conguration.
See page 4-11 for details.
C.P.R. (CPU Parameter Recall)
The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the
BIOS default settings in case the system hangs due to overclocking. When the
system hangs due to overclocking, C.P.R. eliminates the need to open the system
chassis and clear the RTC data. Simply shut down and reboot the system, and the
BIOS automatically restores the CPU default setting for each parameter.
1-4 Chapter 1: Product introduction
This chapter lists the hardware setup
procedures that you have to perform
when installing system components. It
includes description of the jumpers and
connectors on the motherboard.
information
Hardware
2
Chapter summary
2
2.1 Before you proceed ..................................................................... 2-1
2.2 Motherboard overview .................................................................
2.3 Central Processing Unit (CPU) ...................................................
2.4 System memory .........................................................................
2.5 Expansion slots ..........................................................................
2.6 Jumper ........................................................................................
2.7 Connectors .................................................................................
2-2
2-6
2-13
2-16
2-20
2-21
ASUS L1N64-SLI WS
2.1 Before you proceed
L1N64-SLI
WS
L1N64-SLI WS Onboard LED
SB_PWR
ON
Standby
Power
OFF
Powered
Off
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
• Unplug the power cord from the wall socket before touching any
component.
• Use a grounded wrist strap or touch a safely grounded object or to
a metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
• Before you install or remove any component, ensure
that the ATX power supply is switched off or the power cord is detached
from the power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
Onboard LED
The motherboard comes with a standby power LED. The green LED lights up
to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a
reminder that you should shut down the system and unplug the power cable
before removing or plugging in any motherboard component. The illustration
below shows the location of the onboard LED.
ASUS L1N64-SLI WS 2-1
L1N64-SLI
WS
2.2 Motherboard overview
Before you install the motherboard, study the conguration of your chassis to
ensure that the motherboard ts into it.
Make sure to unplug the power cord before installing or removing the
motherboard. Failure to do so can cause you physical injury and damage
motherboard components.
2.2.1 Placement direction
When installing the motherboard, make sure that you place it into the chassis in
the correct orientation. The edge with external ports goes to the rear part of the
chassis as indicated in the image below.
2.2.2 Screw holes
Place nine (9) screws into the holes indicated by circles to secure the motherboard
to the chassis.
Do not overtighten the screws! Doing so can damage the motherboard.
Place this side towards
the rear of the chassis
2-2 Chapter 2: Hardware information
PANEL
L1N64-SLI
WS
CHASSIS
26.7cm (10.5in)
CPU0_FAN
DDR2 DIMM_A2 (64 bit,240-pin module)
FLOPPY
Super
I/O
8Mb
BIOS
VIA
VT6308P
CLRTC
USB910
SB_PWR
EATXPWR
CR2032 3V
Lithium Cell
CMOS Power
Marvell
88E1116
COM1
IE1394_1
30.5cm (12.0in)
NVIDIA
®
MCP55PXE
DDR2 DIMM_B2 (64 bit,240-pin module)
DDR2 DIMM_B1 (64 bit,240-pin module)
DDR2 DIMM_A1 (64 bit,240-pin module)
PCIEX16_1
PCIEX1_1
PCIEX16_2
PCI1
PCIEX16_3
PCIEX16_4
NVIDIA
®
MCP55PXE
ADI
1988B
Marvell
88E1116
CPU1_FAN
HP_FAN1
ATX12V
HP_FAN2
SPS_FAN
CHA_FAN2
HP_FAN3
USB78 USB56
CHA_FAN4
IE1394_2
SATA 1/3/5
PRI_IDE
SATA 2/4/6
SATA 7/9/11
SATA 8/10/12
AAFP
CD
TPM
LAN2_USB34
PS/2KBMS
T: Mouse
B: Keyboard
PARALLEL PORT
SPDIF_O
SPDIF_O2
LAN1_USB12
ESATA
AUDIO
EZ_PLUG1
CHA_FAN1 CHA_FAN3
CPU0
CPU1
2.2.3 Motherboard layout
ASUS L1N64-SLI WS 2-3
2.2.4 Layout contents
Slots Page
1. DDR2 DIMM slots 2-13
2. PCI slots
3. PCI Express x16 slots
4. PCI Express x1 slot
Jumper Page
1. Clear RTC RAM (3-pin CLRTC) 2-20
Rear panel connectors Page
1. PS/2 mouse port (green) 2-21
2. Parallel port
3. LAN 1 (RJ-45) port
4. LAN 2 (RJ-45) port
5. Rear Speaker Out port (black)
6. Center/Subwoofer port (orange)
7. Line In port (light blue)
8. Line Out port (lime)
9. Microphone port (pink)
10. Side Speaker Out port (gray)
11. USB 2.0 ports 1 and 2
12. USB 2.0 ports 3 and 4
13. External SATA port
14. Optical S/PDIF Out port
15. Coaxial S/PDIF Out port
16. PS/2 keyboard port (purple)
2-18
2-18
2-18
2-21
2-21
2-21
2-21
2-21
2-21
2-21
2-22
2-22
2-22
2-22
2-22
2-22
2-22
2-22
2-4 Chapter 2: Hardware information
Internal connectors Page
1. Floppy disk drive connector (34-1 pin FLOPPY) 2-23
®
2. NVIDIA
3. NVIDIA
IDE connector (40-1 pin PRI_IDE) 2-23
®
MCP55PXE Southbridge Serial ATA
2-25
connectors (7-pin SATA1-6 [red], SATA7-12 [black])
4. USB connectors (10-1 pin USB56, USB78, USB910)
5. IEEE 1394a port connectors (10-1 pin IE1394_1, 10-1 pin
2-26
2-26
IE1394_2)
6. CPU, chassis, power, and Heat-pipe Fan connectors
2-27
(4-pin CPU0_FAN, 4-pin CPU1_FAN, 3-pin HP_FAN1~3, 3-pin
CHA_FAN1~4, 3-pin SPS_FAN1)
7. Chassis intrusion connector (4-1 pin CHASSIS)
8. Power connectors (24-pin EATXPWR, 8-pin ATX12V, 4-pin
2-28
2-28
EZ_PLUG1)
9. Front panel audio connector (10-1 pin AAFP)
10. Internal audio connector (4-pin CD [black])
11. Serial port connector (10-1 pin COM1)
12. TPM connector (20-1 pin TPM)
13. System panel connector (20-8 pin PANEL)
•
System power LED (2-pin PLED)
•
Hard disk drive activity LED (2-pin IDE_LED)
•
System warning speaker (4-pin SPEAKER)
•
ATX power button/soft-off button (2-pin PWR)
•
Reset button (2-pin RESET)
2-29
2-30
2-30
2-31
2-32
ASUS L1N64-SLI WS 2-5
2.3 Central Processing Unit (CPU)
L1N64-SLI
WS
L1N64-SLI WS CPU Socket
CPU0
CPU1
The motherboard comes with dual surface mount Socket L1 (1207FX) designed for
the AMD CPU in the Land Grid Array (LGA) package.
• Upon purchase of the motherboard, make sure that the PnP cap is on
the socket and the socket contacts are not bent. Contact your retailer
immediately if the PnP cap is missing, or if you see any damage to the PnP
cap/socket contacts/motherboard components. ASUS shoulders the repair
cost only if the damage is shipment/transit-related.
• Keep the cap after installing the motherboard. ASUS will process Return
Merchandise Authorization (RMA) requests only if the motherboard comes
with the cap on the Socket L1 (1207FX).
• The product warranty does not cover damage to the socket contacts
resulting from incorrect CPU installation/removal, or misplacement/loss/
incorrect removal of the PnP cap.
2.3.1 Installing the CPU
To install a CPU:
1. Locate the CPU socket on the motherboard.
• Before installing the CPU, make sure that the cam box is facing towards
you and the load lever is on your left.
• When installing only one CPU, always install the CPU on the CPU0
socket; otherwise, the system will not boot up.
2-6 Chapter 2: Hardware information
2. Press the load lever with your thumb (A), then move it to the left (B) until it is
released from the retention tab.
Retention tab
A
Load lever
B
To prevent damage to the socket pins, do not remove the PnP cap until you are
installing a CPU.
3. Lift the load lever in the direction of
the arrow to a 135º angle.
4. Lift the load plate with your thumb
and forenger to a 100º angle (A),
then push the PnP cap from the
load plate window to remove (B).
PnP cap
This side of
the socket box
should face
you.
B
A
Load plate
5. Position the CPU
over the socket,
making sure that the
gold triangle is on the
bottom-right corner
of the socket. The
socket alignment
Alignment keys
keys should t into
the CPU notches.
Gold triangle mark
ASUS L1N64-SLI WS 2-7
The CPU ts in only one correct orientation. DO NOT force the CPU into the
socket to prevent bending the connectors on the socket and damaging the CPU!
6. Close the load plate (A), then push
the load lever (B) until it snaps into
the retention tab.
A
B
2-8 Chapter 2: Hardware information
Loading...