ASRock Z490 AQUA Service Manual

Version 1.0
Published March 2020
Copyright©2020 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see ww w.dtsc.ca.gov/hazardouswaste/ perchlorate”
ASRock Website: http://www.asrock.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply)
e terms HDMI® and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
CE Warning
is device complies with directive 2014/53/EU issued by the Commision of the European Community.
is equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. is equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Operations in the 5.15-5.35GHz band are restricted to indoor usage only.
Radio transmit power per transceiver ty pe
Function Frequency Maximum Output Power (EIRP)
2400-2483.5 MHz 18.5 + / -1.5 dbm
5150-5250 MHz 21.5 + / -1.5 dbm
WiFi
Bluetooth 2400-2483.5 MHz 8.5 + / -1.5 dbm
5250-5350 MHz
5470-5725 MHz
18.5 + / -1.5 dbm (no TPC)
21.5 + / -1.5 dbm (TPC)
25.5 + / -1.5 dbm (no TPC)
28.5 + / -1.5 dbm (TPC)
Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specications 2
1.3 Motherboard Layout 9
1.4 I/O Panel 11
1.6 ASRock Thunderbolt™ 3 Module 15
Chapter 2 Installation 19
2.1 Removing the Water-cooling Module 20
2.2 Installing the CPU 27
2.3 Installing the Water-cooling Module 30
2.4 Installing Memory Modules (DIMM) 32
2.5 Installing the Motherboard 34
2.6 Expansion Slots (PCI Express Slots) 35
2.7 Onboard Headers and Connectors 36
2.8 Smart Switches 42
2.9 Status OLED (on I/O Armor) 44
2.10 Dr. Debug 45
2.11 SLITM Operation Guide 51
2.12 CrossFireXTM , 3-Way CrossFireXTM and Quad CrossFireXTM Operation Guide 54
2.12.2 Installing Three CrossFireXTM-Ready Graphics Cards 56
2.13 M.2_SSD (NGFF) Module Installation Guide (M2_1, M2_2) 58
2.14 M.2_SSD (NGFF) Module Installation Guide (M2_3) 63
Chapter 3 Software and Utilities Operation 67
3.1 Installing Drivers 67
3.2 ASRock Motherboard Utility (A-Tuning) 68
3.2.1 Installing ASRock Motherboard Utility (A-Tuning) 68
3.2.2 Using ASRock Motherboard Utility (A-Tuning) 68
3.3 ASRock Live Update & APP Shop 71
3.3.1 UI Overview 71
3.3.2 Apps 72
3.3.3 BIOS & Drivers 75
3.3.4 Setting 76
3.4 Nahimic Audio 77
3.5 ASRock Polychrome SYNC 78
Chapter 4 UEFI SETUP UTILITY 81
4.1 Introduction 81
4.2 EZ Mode 82
4.3 Advanced Mode 83
4.3.1 UEFI Menu Bar 83
4.3.2 Navigation Keys 84
4.4 Main Screen 85
4.5 OC Tweaker Screen 86
4.6 Advanced Screen 96
4.6.1 CPU Conguration 97
4.6.2 Chipset Conguration 99
4.6.3 Storage Conguration 102
4.6.4 Intel(R) Thunderbolt 104
4.6.5 ACPI Conguration 105
4.6.6 USB Conguration 106
4.6.7 Trusted Computing 107
4.7 Tools 108
4.8 Hardware Health Event Monitoring Screen 110
4.9 Security Screen 114
4.10 Boot Screen 115
4.11 Exit Screen 118
Chapter 1 Introduction
ank you for purchasing ASRock Z 490 AQUA motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
In this documentation, Chapter 1 and 2 contains the introduction of the
motherboard and step-by-step installation guides. Chapter 3 contains the operation
guide of the soware and utilities. Chapter 4 contains the conguration guide of
the BIOS setup.
Becau se the motherboard specications and the BIOS soware might be updated, the content of this documentation will be subject to change without notice. In case any modi­cations of this documentation occur, the updated version will be available on ASRock’s website w ithout further notice. If you require technical support related to this mother­board, please visit our website for specic information about the model you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock website http://www.asrock.com.
Z490 AQUA
1.1 Package Contents
ASRock Z490 AQUA Motherboard (EATX Form Factor)
•
ASRock Z490 AQUA Quick Installation Guide
•
ASRock Z490 AQUA Support CD
•
4 x Serial ATA (SATA) Data Cables (Optional)
•
1 x ASRock SLI_HB_Bridge_2S Card (Optional)
•
1 x ASRock WiFi 2.4/5 GHz Antenna (Optiona l)
•
1 x ermal Compound (O pt iona l)
•
5 x Spare ermal Pads (Optional)
•
4 x Spare Screws for MOS and Chokes (Option al)
•
4 x Spare Screws for CPU Sockets (Optional)
•
6 x Spare Screws for M.2 Heatsinks (Option al)
•
2 x 90° Tubing Elbow Fittings (Optional)
•
6 x G1/4" to 14mm Tube Fittings (Optional)
•
2 x G1/4" Plugs (Optional)
•
2 x G1/4" to 14mm 90° Rotary Fittings (Optional)
•
1 x Ball Valve (Optiona l)
•
3 x Screws for M.2 Sockets (Optional)
•
2 x Standos for M.2 Sockets (Optional)
•
English
1
1.2 Specications
Platform
CPU
Chipset
Memory
•
•
•
•
•
•
•
•
•
•
•
•
•
•
* Please refer to Memory Support List on ASRock's website for
more information. (http://www.asrock.com/)
* CoreTM (i9/i7) support DDR4 up to 2933; CoreTM (i5/i3),
Pentium® and Celeron® support DDR4 up to 2666.
•
•
•
•
EATX Form Factor
8 Layer PCB
2oz Copper PCB
Suppor ts 10th Gen and future generation Intel® CoreTM
Processors (Socket 1200)
Digi Power design
16 Power Phase design
Supports Intel® Turbo Boost Ma x 3.0 Technology
Supports Intel® K-Series unlocked CPUs
Supports ASRock BCLK Full-range Overclocking
Supports ASRock Hyper BCLK Engine III
Intel® Z490
Dual Channel DDR4 Memory Technology
4 x DDR4 DIMM Slots
Support s DDR4 4700+(OC)*/46 66/460 0/450 0/4 400/4 333/42
66(OC)/4133(OC)/4000(OC)/3866(OC)/3800(OC)/3733(OC)
/3600(OC)/3200(OC)/2933/2800/2666/2400/2133 non-ECC,
un-buered memory
Supports ECC UDIMM memory modules (operate in non-
ECC mode)
Max. capacity of system memory: 128GB
Supports Intel® Extreme Memory Prole (XMP) 2.0
15μ Gold Contact in DIMM Slots
English
2
Expansion Slot
3 x PCI Express 3.0 x16 Slots (PCIE1/PCIE4/PCIE5: single
•
at x16 (PCIE1); dual at x8 (PCIE1) / x8 (PCIE4); triple at x8
(PCIE1) / x8 (PCIE4) / x4 (PCIE5))*
Graphics
* PCIE5, M2_3 and SATA3_3 share lanes. If either one of them
is in use, the others will be disabled.
* Supports NVMe SSD as boot disks
2 x PCI Express 2.0 x1 Slots
•
Supports AMD Quad CrossFireXTM, 3-Way CrossFireXTM
•
and CrossFireXTM
Supports NVIDIA® SLI
•
Support NVIDIA® SLITM with NVIDIA® Quadro graphics
•
cards
Supports NVIDIA® NVLinkTM with dual NVIDIA® GeForce®
•
RTX series graphics cards**
** NVIDIA NVLink Bridge does not come with the package.
Please purchase it from NVIDIA® if necessary.
1 x Vertical M.2 Socket (Key E) with the bundled WiFi-
•
802.11ax module (on the rear I/O)
15μ Gold Contact in VGA PCIe Slot (PCIE1 and PCIE4)
•
Intel® UHD Graphics Built-in Visuals and the VGA outputs
•
can be supported only with processors which are GPU
integrated.
Hardware Accelerated Codecs: AVC/H.264, HEVC/H.265
•
8bit, HEVC/H.265 10bit, VP8, VP9 8bit, VP9 10bit, MPEG 2,
MJ PEG, VC-1
* VP9 10bit and VC-1 are for decode only.
* VP8 and VP9 encode are not supported by Windows OS.
Graphics, Media & Compute: Microso DirectX 12, OpenGL
•
4.5, Intel® Built In Visuals, Intel® Quick Sync Video, Hybrid /
Switchable Graphics, OpenCL 2.1
Display & Content Security: Rec. 2020 (Wide Color Gamut),
•
Microso PlayReady 3.0, Intel® SGX Content Protection,
UHD/HDR Blu-ray Disc
Supports HDMI 1.4 with max. resolution up to 4K x 2K
•
(4096x2160) @ 30Hz
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
•
HBR (High Bit Rate Audio) with HDMI 1.4 Port (Compliant
HDMI monitor is required)
Supports HDCP 2.3 with HDMI 1.4 Port
•
Supports 4K Ultra HD (UHD) playback with HDMI 1.4 Port
•
TM
Z490 AQUA
English
3
Thunder-
TM
bolt
Audio
Intel® JHL7540 underboltTM 3 Controller (Titan R idge)
•
Supports underboltTM 3 interface with max. resolution of
•
5K (5120 x 2880) @ 60Hz for one display over a single cable
connection
Supports underboltTM 3 interface with max. resolution of
•
4K x 2K (4096x2160) @ 60Hz for dual displays over a single
cable connection
Supports up to two streams (eight lanes) of DisplayPort video
•
bandwidth; supports daisy-chaining of multiple DisplayPort
monitors
7.1 CH HD Audio with Content Protection (Realtek
•
ALC1220 Audio Codec)
Premium Blu-ray Audio support
•
Supports Surge Protection
•
WIMA Audio Capacitors (For Front Outputs)
•
ESS SABR E9218 DAC for Front Panel Audio
•
120dB SNR DAC with Dierential Amplier
•
Pure Power-In
•
Direct Drive Technology
•
PCB Isolate Shielding
•
Impedance Sensing on Rear Out port
•
Individual PCB Layers for R/L Audio Channel
•
Gold Audio Jacks
•
15μ Gold Audio Connector
•
Nahimic Audio
•
English
4
LAN
1 x 10 Gigabit LAN 100/1000/2500/5000/10000 Mb/s
(AQUANT IA® AQC107):
Supports Wake-On-LAN
•
Supports Lightning/ESD Protection
•
Supports PXE
•
1 x 2.5 Gigabit LAN 10/100/1000/2500 Mb/s
(Dragon RTL8125BG)
Supports Dragon 2.5G LAN Soware
•
- Smart Auto Adjust Bandwidth Control
- Visual User Friendly UI
- Visual Network Usage Statistics
Wireless LAN
Rear Panel I/O
- Optimized Default Setting for Game, Browser, and
Streaming Modes
- User Customized Priority Control
Supports Wake-On-LAN
•
Supports Lightning/ESD Protection
•
Supports Energy Ecient Ethernet 802.3az
•
Supports PXE
•
Intel® 802.11ax WiFi Module
•
Supports IEEE 802.11a/b/g/n/ax
•
Supports Dual-Band (2.4/5 GHz)
•
Supports WiFi6 802.11ax (2.4Gbps)
•
2 antennas to support 2 (Transmit) x 2 (Receive) diversity
•
technolog y
Supports Bluetooth 5.1 + High speed class II
•
Supports MU-MIMO
•
2 x Antenna Ports
•
1 x HDMI Port
•
1 x Optical SPDIF Out Port
•
2 x USB 3.2 Gen2 underboltTM 3 Type-C Ports
•
(40Gb/s for underbolt protocol; 10 Gb/s for USB3.2
protocol) (Supports ESD Protection)*
* Supports USB-PD 3.0 9V/3A(27W) and 5V/3A(15W)
2 x Mini DisplayPort Input Ports**
•
** Please choose regular mini DisplayPort to DisplayPort
adapter cables instead of right angled ones if you use two mini
DisplayPort input ports simultaneously.
3 x USB 3.2 Gen2 Type-A Ports (10 Gb/s) (ReDriver)
•
(Supports ESD Protection)
1 x USB 3.2 Gen2 Type-C Port (10 Gb/s) (Supports ESD
•
Protection)
4 x USB 3.2 Gen1 Ports (Intel® Z490) (Supports ESD
•
Protection)***
*** Ultra USB Power is supported on USB3_123 ports.
*** ACPI wake-up function is not supported on USB3_123
ports.
2 x RJ-45 LAN Ports with LED (ACT/LINK LED and SPEED
•
LED)
Z490 AQUA
English
5
Storage
1 x Clear CMOS Button
•
1 x BIOS Flashback Button
•
HD Audio Jacks: Rear Speaker / Centra l / Bass / Line in /
•
Front Speaker / Microphone (Gold Audio Jacks)
6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,
•
RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology
17), NCQ, AHCI and Hot Plug*
2 x SATA3 6.0 Gb/s Connectors by ASMedia ASM1061,
•
support NCQ, AHCI and Hot Plug
* M2_1, SATA3_0 and SATA3_1 share lanes. If either one of
them is in use, the others will be disabled.
* M2_ 2, SATA3_4 and SATA3_5 share lanes. If either one of
them is in use, the others will be disabled.
* PCIE5, M2_3 and SATA3_3 share lanes. If either one of them
is in use, the others will be disabled.
1 x Ultra M.2 Socket (M2_1), supports M Key type
•
2260/2280 M.2 PCI Express module up to Gen3 x4
(32 Gb/s)**
1 x Ultra M.2 Socket (M2_2), supports M Key ty pe
•
2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI
Express module up to Gen3 x4 (32 Gb/s)**
1 x Ultra M.2 Socket (M2_3), supports M Key ty pe
•
2260/2280/22110 M.2 SATA3 6.0 Gb/s module and M.2 PCI
Express module up to Gen3 x4 (32 Gb/s)**
** Supports Intel® OptaneTM Tech nolo gy
** Supports NVMe SSD as boot disks
** Supports ASRock U.2 Kit
English
6
Connector
1 x SPI TPM Header
•
1 x Power LED and Speaker Header
•
2 x RGB LED Headers
•
* Support in total up to 12V/3A, 36W LED Strip
2 x Addressable LED Headers
•
* Support in total up to 5V/3A, 15W LED Strip
1 x CPU Fan Connector (4-pin)
•
* e CPU Fan Connector supports the CPU fan of ma ximum
1A (12W) fan power.
1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan
•
Speed Control)
6 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan
•
Speed Control)
* e Chassis/Water Pump Fan supports the water cooler fan of
maximum 2A (24W) fan power.
* CPU_FAN2/WP_3A, CHA_FAN1/WP, CHA_FAN2/WP,
CHA_FAN3/WP, CHA_FAN4/WP, CHA_FAN5/WP and
CHA_FAN6/WP can auto detect if 3-pin or 4-pin fan is in use.
* CPU_FAN2/WP_3A supports the water cooler fan of maxi-
mum 3A (36W) fan power.
1 x 24 pin ATX Power Connector (Hi-Density Power
•
Connec tor)
2 x 8 pin 12V Power Connectors (Hi-Density Power
•
Connec tor)
1 x Front Panel Audio Connector (15μ Gold Audio
•
Connec tor)
1 x USB 2.0 Header (Supports 2 USB 2.0 ports) (Intel® Z490)
•
(Supports ESD Protection)
2 x USB 3.2 Gen1 Headers (Support 4 USB 3.2 Gen1 ports)
•
(ASMedia ASM1074 hub) (Supports ESD Protection)
1 x Front Panel Type C USB 3.2 Gen2 Header (Intel® Z490)
•
(Supports ESD Protection)
1 x Dr. Debug with LED
•
1 x Power Button with LED
•
1 x Reset Button with LED
•
1 x Retry Button
•
1 x Safe Boot Button
•
Z490 AQUA
BIOS Feature
AMI UEFI Legal BIOS with multilingual GUI support
•
ACPI 6.0 Compliant wake up events
•
SMBIOS 2.7 Support
•
CPU Core/Cache, GT, DRAM, VPPM,VTTDDR, VCCSFR,
•
VCCPLL_OC, PCH Voltage, VCCIO, VCCST, VCCSA,
CPU Internal PLL, GT PLL, Ring PLL, System Agent PLL,
Memory Controller PLL Voltage Multi-adjustment
English
7
Temperature Sensing: CPU, CPU/Water Pump, Chassis/Wa-
Hardware Monitor
•
ter Pump Fans
Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water
•
Pump Fans
Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
•
ture): CPU, CPU/Water Pump, Chassis/Water Pump Fans
Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/
•
Water Pump Fans
Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,
•
VPPM, PCH, VCCSA, VCCST, VCCIO, VCCPLL_OC,
VCCSFR
1 x Status OLED
•
Microso® Windows® 10 64-bit
OS
Certica­tions
* For detailed product information, please visit our website: http://www.asrock .com
Please realiz e that the re is a certain r isk involved with o verclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technolog y, or using third-party overclocking to ols. O verclocking may aect your system’s stability, or even c ause damage to the components and devices of your system. It should be don e at your ow n risk and expense. We are not responsibl e for possible damage caused by overclo cking.
•
FCC, CE
•
ErP/EuP ready (ErP/EuP ready power supply is required)
•
English
8
1
RGB_LED2
1
ADDR_LED1
1
ADDR_LED2
1
CPU_FAN2/WP_3A
PCIE2
Top: RJ-45
(AQUANTIA AQC107)
4
2932 3133
LAN
PCIE5
Intel
Z490
ATX12V1
1
SPK_PLED1
ATX12V2
1
USB3_ 5_6
1
SPI_TPM_J1
CHA_FAN2/WP
CHA_FAN4/WP
M2_2
USB 3.2 Gen2 T: USB31_TA_3 USB 3.2 Gen2 B: USB31_TC_1
DDR 4_A2 (6 4 bit, 28 8-pin m odule )
DDR 4_A1 (6 4 bit, 28 8-pin m odule )
DDR 4_B2 (6 4 bit, 28 8-pin m odule )
DDR 4_B1 (6 4 bit, 28 8-pin m odule )
ATXP WR 1
PCIE1
USB 3.2 Gen2 T: USB31_TA_1 B: USB31_TA_2
Top:
Central/Bass
Center :
REAR SPK
Top:
LINE IN
Center :
FRONT
Bottom :
Optica l
SPDIF
Bottom :
MIC IN
PCIE4
HDLED RESET
PLED PWRBTN
PANEL1
1
1
HD_AUDIO1
SATA3_0_1
SATA3_3_2 _3
SATA3_A1_ A2
13
17
16
20
19
21
SATA3_4_5
22
23
USB_1_2
1
1
5
Dr.
Debug
26
CMOS
Battery
CPU_FAN1
14
Reset
Power
CHA_FAN5 /WP
6
LAN
M2_WIFI_1
3
USB31_TC_2
PCIE3
2
BIOS _FB1
CHA_FAN1 /WP
10
15
USB3_ 7_8
CHA_FAN3/WP
CHA_FAN6/WP
24
25
2728
TBT_M2_1
TBT_M2_2
M2_1
CT2CT3CT4 CT1
RK L_M2
18
M2_3
CLRC MOS
HDMI1
USB 3.2 Gen1 USB3_1234
11
12
9
Top:
2.5GLAN
(Realtek RTL8125AG)
30
AUDIO CODEC
BFG_BTN1
RTY_BTN1
7
8
1.3 Motherboard Layout
RGB_LED1
Z490 AQUA
BIOS ROM
English
9
English
No. Description
1 8 pin 12V Power Connector (ATX12V1)
2 8 pin 12V Power Connector (ATX12V2)
3 CPU Fan Connector (CPU_FAN1)
4 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
5 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
6 CPU/Water Pump Fan Connector (CPU_FAN2/WP_3A)
7 Addressable LED Header (ADDR_LED2)
8 RGB LED Header (RGB_LED2)
9 Safe Boot Button (BFG_BTN1)
10 Reset Button (RSTBTN1)
11 Power Button (PWRBTN1)
12 Retry Button (RTY_BTN1)
13 ATX Power Connector (ATXPWR1)
14 Chassis/Water Pump Fan Connector (CHA_FAN5/WP)
15 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)
16 Front Panel Type C USB 3.2 Gen2 Header (USB31_TC_2)
17 USB 3.2 Gen1 Header (USB3_5_6)
18 USB 3.2 Gen1 Header (USB3_7_8)
19 SPI TPM Header (SPI_TPM_J1)
20 SATA3 Connectors (SATA3_0_1)
21 SATA3 Connectors (SATA3_2_3)
22 SATA3 Connectors (SATA3_4_5)
23 SATA3 Connectors (SATA3_A1_A2)
24 Chassis/Water Pump Fan Connector (CHA_FAN3/WP)
25 Chassis/Water Pump Fan Connector (CHA_FAN6/WP)
26 System Panel Header (PANEL1)
27 Power LED and Speaker Header (SPK_PLED1)
28 Chassis/Water Pump Fan Connector (CHA_FAN4/WP)
29 Chassis/Water Pump Fan Connector (CHA _FAN2/WP)
30 USB 2.0 Header (USB_1_2)
31 RGB LED Header (RGB_LED1)
32 Addressable LED Header (ADDR_LED1)
33 Front Panel Audio Header (HD_AUDIO1)
10
1.4 I/O Panel
1
2 4
3 5
Z490 AQUA
6
7
16
17
18
No. Description No. Description
1 BIOS Flashback Button 10 USB 3.2 Gen2 Type-A Port
2 Central / Bass (Orange) (USB31_TA_3)
3 Rear Speaker (Black) 11 USB 3.2 Gen2 Type-C Port
4 Line In (Light Blue) (USB31_TC_1)
5 Front Speaker (Lime)* 12 USB 3.2 Gen2 Ports (USB31_TA_12)
6 2.5G LAN RJ-45 Port 13 USB 3.2 Gen1 Ports
(Dragon RTL8125BG)** (USB3_1234)*****
7 10G LAN RJ-45 Port 14 Microphone (Pink)
(AQUANTIA® AQC107)*** 15 Optical SPDIF Out Port
8 Mini DisplayPort Input Ports**** 16 HDMI Port
9 USB 3.2 Gen2 underboltTM 3 17 Antenna Ports
Type-C Ports 18 Clear CMOS Button
1415
1213
10
11
9 8
11
English
* If you use a 2-channel spea ker, please connect the s peaker’s plug into “Front Speaker Jack”. See the table below
for connection d etails in accordance w ith the type of speaker you use.
Audio Output
Channels
Front Speaker
(No. 5)
Rear Speaker
(No. 3)
Central / Bass
(No. 2)
Line In
(No. 4)
2 V -- -- -- 4 V V -- -- 6 V V V -- 8 V V V V
** ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
LAN Por t
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection
Blinking Data Activity Orange
100Mbps/1Gbps
connection
On Link Green 2.5Gbps connection
*** ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
English
12
LAN Por t
Activity / Link LED Speed LED
Status Description Status Description
O No Link
Blinking Data Activity
Orange
100Mbps/1Gbps/2.5Gbps
/5Gbps connection
On Link Green 10Gbps connection
Z490 AQUA
**** Please choose regular mini DisplayPort to DisplayPort adapter cables instead of right angled ones if you use two mini DisplayPort input ports simultaneously.
***** ACPI wake-up function is not supported on USB3_123 port s.
13
English
1.5 WiFi-802.11ax Module and ASRock WiFi 2.4/5 GHz Antenna
WiFi-802.11ax + BT Module
is motherboard comes with an exclusive WiFi 802.11 a/b/g/n/ax + BT v5.1
module (pre-installed on the rear I/O panel) that oers support for WiFi 802.11 a/b/
g/n/ax connectivity standards and Bluetooth v5.1. WiFi + BT module is an easy-to-
use wireless local area network (WLAN) adapter to support WiFi + BT. Bluetooth
v5.1 standard features Smart Ready technology that adds a whole new class of
functionality into the mobile devices. BT 5.1 also includes Low Energy Technology
and ensures extraordinary low power consumption for PCs. e 2T2R WiFi
solution sets a WiFi high speed standard and oers max link rate up to 2.4Gbps.
* e transmission speed may vary according to the environment.
ASRock WiFi 2.4/5 GHz Antenna
English
14
1.6 ASRock Thunderbolt™ 3 Module
USB 3.2 Gen2 underboltTM 3
Type-C Ports
Mini DisplayPort Input Ports
Specications
Z490 AQUA
TBT_M2_1 and TBT_M2 _2
Platform •
Controller •
M.2
Connector
Interface
Size: 1.45-in x 1.65-in x 0.91-in, 3.7 cm x 4.2 cm x 2.3 cm
Intel® JHL7540 underboltTM 3 Controller (Titan R idge)
Proprietary design for ASRock specic motherboard
•
* Please note that plug ging into other M.2 connector may damage the motherboard and this module
2 x NGFF M Key Type M.2 Connectors
•
2 x Mini DisplayPort 1.4 Input Ports
•
2 x USB 3.2 Gen2 underboltTM 3 Type-C Ports (40Gb/s for
•
underbolt protocol; 10 Gb/s for USB3.2 protocol) (Support
ESD Protection)*
*Supports daisy-chaining of up to six u nderboltTM devices. *is port supports USB-PD 3.0 power outputs 9V/3A 27W and 5V/3A 15W. For charging Type-C USB devices, the device should support Type-C standards to adjust the current because it will be dierent in Power On state (3 Amp). *Some Type-C USB devices may only be charged by its own adapter.
PCI Express 3.0 x4 interface
•
English
15
Graphics
Data Rate
OS
Supports underboltTM 3 interface with max. resolution of
•
5K (5120 x 2880) @ 60Hz for one display over a single cable
connection
Supports underboltTM 3 interface with max. resolution of
•
4K x 2K (4096x2160) @ 60Hz for dual displays over a single
cable connection
Supports up to two streams (eight lanes) of DisplayPort video
•
bandwidth; supports daisy-chaining of multiple DisplayPort
monitors
Supports 40Gbps bi-directional bandwidth per channel with
•
underboltTM 3 port
Microso® Windows® 10 64-bit
•
English
16
Installation
Step 1
Prepare two Mini DisplayPort to DisplayPort Adapter Cables and one/two
underboltTM cables. All these cables are not included in the package.
Step 2
Connect one end of the Mini DisplayPort to DisplayPort Adapter Cable to the Mini
DisplayPort Input Port (A) on ASRock underboltTM 3 Module on I/O panel.
en connect the other end of the cable to the DisplayPort Output Port (B) on the
graphics card.
Z490 AQUA
A
B
English
17
Step 3
Follow step 2 to connect the other Mini DisplayPort Input Port to the graphics card.
1. Make sure to connect both Mini DisplayPort Input Port s if you install the under­boltTM output display device.
2. Please choose regular Mini DisplayPort to DisplayPor t Adapter Cables instead of right angled ones if you u se two Mini Displ ayPort Input Ports s imultaneously.
English
18
Step 4
Connect the underboltTM cable(s) from your underbolt-enabled device(s) to the
USB 3.2 Gen2 underboltTM 3 Type-C Port(s) on ASRock underboltTM 3 Module
on I/O panel.
Chapter 2 Installation
is is an EATX form factor motherboard. Before you install the motherboard,
study the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
Make sure to unplug the power cord before installing or removing the motherboard
•
components. Failure to do so may cause physical injuries and damages to motherboard
components.
In order to avoid damage from static electricity to the motherboard’s components,
•
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
Hold components by the edges and do not touch the ICs.
•
Whenever you uninstall any components, place them on a grounded anti-static pad or
•
in the bag that comes with the components.
When placing screws to secure the motherboard to the chassis, please do not over-
•
tighten the screws! Doing so may damage the motherboard.
Z490 AQUA
19
English
1
2.1 Removing the Water-cooling Module
Removing the CPU Backplate
English
20
Please unscrew the eight screws from the bottom side of the motherboard to release the
backplate and the water-cooling module. e positions are indicated as below.
Z490 AQUA
21
English
2
AQUA_CPULED
Removing the
Water-cooling Module
B
A
English
22
Unplug the LED Plug from the motherboard before removing the Water-cooling Module.
Screw Assembly Schematic
Front View
1 1
Z490 AQUA
1 1
11
English
23
Loading...
+ 98 hidden pages