ASRock Z390 EXTREME4 User Manual

Page 1
Version 1.1 Published August 2018 Copyright©2018 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”
ASRock Website: http://www.asrock.com
Page 2
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply)
e terms HDMI® and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535; 7,003,467 & other U.S. and worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together is a registered trademark & DTS Connect, DTS Interactive, DTS Neo:PC are trademarks of DTS, Inc. Product includes soware. © DTS, Inc., All Rights Reserved.
Page 3
Motherboard Layout
Intel
Z390
DDR 4_A2 (6 4 bit, 28 8-pin mo dule)
DDR 4_A1 (6 4 bit, 28 8-pin mo dule)
DDR 4_B2 (6 4 bit, 28 8-pin mo dule)
DDR 4_B1 (6 4 bit, 28 8-pin mo dule)
ATX12V1
ATXP WR 1
LAN
PCIE2
Top: RJ-45
Top:
Central/Bass
Center :
REAR SPK
Top:
LINE IN
Center :
FRONT
Bottom :
Optica l
SPDIF
Bottom :
MIC IN
PCIE4
HDLED RESET
PLED PWRBTN
PANEL1
1
1
SPK_PLED1
COM1
1
1
HD_AUDIO1
Z390 EXTREME4
PCIE6
SATA3_2_3
SATA3_0_1
SATA3_A1_ A2
PCIE1
RoHS
7
9
10
11
12
13
14
USB_1_2
1
20
USB_3_4
1
19
2128
30
SATA3_4_5
1
6
5
17
PS2
Keybo ard
/Mous e
CMOS
Battery
PCIE3
M2_1
M2_2
CT2
CT2
CT3
CT3
CT4
CT4CT5
T B1
1
24
3
USB3_7 _8
1
18 16
CPU_FAN1
8
22
1
TPMS1
PCIE5
CT1
CT1
CHA_FAN1/WP
Ultra M.2
PCIe Gen3x4
CHA_FAN2/WP
CPU_FAN2/WP
CHA_FAN3/WP
4
USB3_5 _6
1
25
CLRMOS1
1
LAN
23
Ultra M.2
PCIe Gen3x4
USB31_TC_2
USB 3.1 Gen1 T: USB3 B: USB4
USB 3.1 Ge n1
T: USB1
B: USB2
USB 3.1 Gen2 T: USB31_TA_1 B: USB31_TC_1
ATX12V2
2
RGB_LED2
1
ADDR_LED1
1
26
RGB_LED1
1
27
BIOS_A1
BIOS_B1
BIOS
BIOS
BIOS_A_LED1BIOS_B_LED1
29
M2_3
CT1
DIS PLAY1
HDM I1
Purity
Sound 4
TM
PM_OC
1
15
Z390 Extreme4
English
1
Page 4
English
No. Description
1 8 pin 12V Power Connector (ATX12V1)
2 4 pin 12V Power Connector (ATX12V2)
3 CPU Fan Connector (CPU_FAN1)
4 CPU/Water Pump Fan Connector (CPU_FAN2/WP)
5 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
6 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
7 ATX Power Connector (ATXPWR1)
8 USB 3.1 Gen1 Header (USB3_5_6)
9 USB 3.1 Gen1 Header (USB3_7_8)
10 Front Panel Type C USB 3.1 Gen1 Header (USB31_TC_2)
11 SATA3 Connectors (SATA3_4_5)
12 SATA3 Connectors (SATA3_2_3)
13 SATA3 Connectors (SATA3_0_1)
14 SATA3 Connectors (SATA3_A1_A2)
15 Performance Mode / Easy OC Header (PM_OC)
16 Chassis/Water Pump Fan Connector (CHA_FAN3/WP)
17 System Panel Header (PANEL1)
18 Power LED and Speaker Header (SPK_PLED1)
19 USB 2.0 Header (USB_3_4)
20 USB 2.0 Header (USB_1_2)
21 COM Port Header (COM1)
22 TPM Header (TPMS1)
23 Chassis/Water Pump Fan Connector (CHA_FAN2/WP)
24 underbolt AIC Connector (TB1)
25 RGB LED Header (RGB_LED2)
26 RGB LED Header (RGB_LED1)
27 Addressable LED Header (ADDR_LED1)
28 Front Panel Audio Header (HD_AUDIO1)
29 Clear CMOS Jumper (CLRMOS1)
30 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)
2
Page 5
I/O Panel
1
2 547
3
Z390 Extreme4
6
16
No. Description No. Description
1 PS/2 Mouse/Keyboard Port 9 Optical SPDIF Out Port
2 D-Sub Port 10 Antenna Ports
3 LAN RJ-45 Port* 11 USB 3.1 Gen2 Type-A Port (USB31_TA_1)
4 Central / Bass (Orange) 12 USB 3.1 Gen2 Type-C Port (USB31_TC_1)
5 Rear Speaker (Black) 13 USB 3.1 Gen1 Ports (USB3_34)
6 Line In (Light Blue) 14 HDMI Port
7 Front Speaker (Lime)** 15 DisplayPort 1.2
8 Microphone (Pink) 16 USB 3.1 Gen1 Port (USB3_12)
13
11 10
12
8915 14
English
3
Page 6
* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
LAN Por t
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection
** If you use a 2- channel speaker, plea se connect the speake r’s plug into “Front Speaker Jack”. See the table below for connection d etails in accordance w ith the type of speaker you use.
English
Audio Output
Channels
Front Speaker
(No.7)
Rear Speaker
(No. 5)
Central / Bass
(No. 4)
2 V -- -- -- 4 V V -- -- 6 V V V -- 8 V V V V
Line In
(No. 6)
4
Page 7
Chapter 1 Introduction
ank you for purchasing ASRock Z390 Extreme4 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
Becau se the motherboard specications and the BIOS soware might be updated, the content of this documentation will be subject to change without notice. In case any modi­cations of this documentation occur, the updated version will be available on ASRock’s website w ithout further notice. If you require technical support related to this mother­board, please visit our website for specic information about the model you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock website http://www.asrock.com.
1.1 Package Contents
ASRock Z390 Extreme4 Motherboard (ATX Form Factor)
•
ASRock Z390 Extreme4 Quick Installation Guide
•
ASRock Z390 Extreme4 Support CD
•
1 x I/O Panel Shield
•
4 x Serial ATA (SATA) Data Cables (Optional)
•
1 x ASRock SLI_HB_Bridge_2S Card (Optional)
•
3 x Screws for M.2 Socket (Optional)
•
Z390 Extreme4
English
5
Page 8
1.2 Specications
Platform
CPU
Chipset
Memory
•
•
•
•
•
•
•
•
•
•
•
* Please refer to Memory Support List on ASRock's website for more information. (http://www.asrock.com/)
•
•
•
•
ATX Form Factor
Supports 9th and 8th Gen Intel® CoreTM Processors (Socket
1151) Digi Power design 12 Power Phase design Supports Intel® Turbo Boost 2.0 Technology Supports Intel® K-Series unlocked CPUs Supports ASRock BCLK Full-range Overclocking
Intel® Z390
Dual Channel DDR4 Memory Technology 4 x DDR4 DIMM Slots Supports DDR4 4300+(OC)*/4266(OC)/4133(OC)/4000 (OC)/3866(OC)/3800(OC)/3733(OC)/3600(OC)/3200(OC)/ 2933(OC)/2800(OC)/2666/2400/2133 non-ECC, un-buered memory
Supports ECC UDIMM memory modules (operate in non­ECC mode) Max. capacity of system memory: 64GB Supports Intel® Extreme Memory Prole (XMP) 2.0 15μ Gold Contact in DIMM Slots
English
6
Expansion Slot
3 x PCI Express 3.0 x16 Slots (PCIE2/PCIE4/PCIE6: single
•
at x16 (PCIE2); dual at x8 (PCIE2) / x8 (PCIE4); triple at x8 (PCIE2) / x8 (PCIE4) / x4 (PCIE6))*
* Supports NVMe SSD as boot disks
3 x PCI Express 3.0 x1 Slots (Flexible PCIe)
•
Supports AMD Quad CrossFireXTM, 3-Way CrossFireXTM
•
and CrossFireXTM Supports NVIDIA® Quad SLITM and SLI
•
1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module
•
and Intel® CNVi (Integrated WiFi/BT) 15μ Gold Contact in VGA PCIe Slot (PCIE2)
•
TM
Page 9
Graphics
Intel® UHD Graphics Built-in Visuals and the VGA outputs
•
can be supported only with processors which are GPU integrated. Supports Intel® UHD Graphics Built-in Visuals : Intel®
•
Quick Sync Video with AVC, MVC (S3D) and MPEG-2 Full HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® UHD Graphics DirectX 12
•
HWAEncode/Decode: AVC/H.264, HEVC/H.265 8-bit,
•
HEVC/H.265 10-bit, VP8, VP9 8-bit, VP9 10-bit (Decode only), MPEG2, MJPEG, VC-1 (Decode only) ree graphics output options: D-Sub, HDMI and
•
DisplayPort 1.2 Supports Triple Monitor
•
Supports HDMI with max. resolution up to 4K x 2K
•
(4096x2160) @ 30Hz Supports DisplayPort 1.2 with max. resolution up to 4K x 2K
•
(4096x2304) @ 60Hz Supports D-Sub with max. resolution up to 1920x1200 @
•
60Hz Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
•
HBR (High Bit Rate Audio) with HDMI Port (Compliant HDMI monitor is required) Supports HDCP with HDMI and DisplayPort 1.2 Ports
•
Supports 4K Ultra HD (UHD) playback with HDMI and
•
DisplayPort 1.2 Ports
Z390 Extreme4
Audio
7.1 CH HD Audio with Content Protection (Realtek
•
ALC1220 Audio Codec) Premium Blu-ray Audio support
•
Supports Surge Protection
•
Supports Purity SoundTM 4
•
- Nichicon Fine Gold Series Audio Caps
- 120dB SNR DAC with Dierential Amplier
- NE5532 Premium Headset Amplier for Front Panel Audio Connector (Supports up to 600 Ohm headsets)
- Pure Power-In
English
7
Page 10
LAN
Rear Panel I/O
- Direct Drive Technology
- PCB Isolate Shielding
- Impedance Sensing on Rear Out port
-
Individual PCB Layers for R/L Audio Channel
- RGB LED
- 15μ Gold Audio Connector Supports DTS Connect
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Supports Wake-On-LAN
•
Supports Lightning/ESD Protection
•
Supports Energy Ecient Ethernet 802.3az
•
Supports PXE
•
2 x Antenna Ports
•
1 x PS/2 Mouse/Keyboard Port
•
1 x D-Sub Port
•
1 x HDMI Port
•
1 x DisplayPort 1.2
•
1 x Optical SPDIF Out Port
•
1 x USB 3.1 Gen2 Type-A Port (10 Gb/s) (ReDriver) (Supports
•
ESD Protection) 1 x USB 3.1 Gen2 Type-C Port (10 Gb/s) (ReDriver) (Supports
•
ESD Protection) 4 x USB 3.1 Gen1 Ports (Intel® Z390) (Supports ESD
•
Protection) 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
•
LED) HD Audio Jacks: Rear Speaker / Central / Bass / Line in /
•
Front Speaker / Microphone
English
8
Storage
6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,
•
RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology
16), NCQ, AHCI and Hot Plug* 2 x SATA3 6.0 Gb/s Connectors by ASMedia ASM1061, sup-
•
port NCQ, AHCI and Hot Plug
Page 11
Connector
Z390 Extreme4
* M2_1, SATA3_0 and SATA3_1 share lanes. If either one of them is in use, the others will be disabled. * M2_2, SATA3_4 and SATA3_5 share lanes. If either one of them is in use, the others will be disabled.
1 x Ultra M.2 Socket (M2_1), supports M Key type
•
2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x4 (32 Gb/s)** 1 x Ultra M.2 Socket (M2_2), supports M Key type
•
2230/2242/2260/2280/22110 M.2 SATA3 6.0 Gb/s module
and M.2 PCI Express module up to Gen3 x4 (32 Gb/s)** ** Supports Intel® OptaneTM Tech nolo gy ** Supports NVMe SSD as boot disks ** Supports ASRock U.2 Kit
1 x COM Port Header
•
1 x TPM Header
•
1 x Power LED and Speaker Header
•
2 x RGB LED Headers
•
* Support in total up to 12V/3A, 36W LED Strip
1 x Addressable LED Header
•
* Supports in total up to 5V/3A, 15W LED Strip
1 x CPU Fan Connector (4-pin)
•
* e CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.
1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan
•
Speed Control) * e CPU/Water Pump Fan supports the water cooler fan of maximum 2A (24W) fan power.
3 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan
•
Speed Control) * e Chassis/Water Pump Fan supports the water cooler fan of maximum 2A (24W) fan power. * CPU_FAN2/WP, CHA_FAN1/WP, CHA_FAN2/WP and CHA_FAN3/WP can auto detect if 3-pin or 4-pin fan is in use.
1 x 24 pin ATX Power Connector (Hi-Density Power
•
Connec tor)
1 x 8 pin 12V Power Connector (Hi-Density Power
•
Connec tor)
English
9
Page 12
BIOS Feature
Hardware Monitor
1 x 4 pin 12V Power Connector (Hi-Density Power
•
Connec tor) 1 x Front Panel Audio Connector (15μ Gold Audio
•
Connec tor) 1 x underbolt AIC Connector (5-pin)
•
2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Intel® Z390)
•
(Supports ESD Protection) 2 x USB 3.1 Gen1 Headers (Support 4 USB 3.1 Gen1 ports)
•
(ASMedia ASM1074 hub) (Supports ESD Protection) 1 x Front Panel Type C USB 3.1 Gen1 Header (Intel® Z390)
•
(Supports ESD Protection) 1 x Performance Mode / Easy OC Header
•
2 x AMI UEFI Legal BIOS with multilingual GUI support (1
•
x Main BIOS and 1 x Backup BIOS) Supports Secure Backup UEFI Technology
•
ACPI 6.0 Compliant wake up events
•
SMBIOS 2.7 Support
•
CPU Core/Cache, GT, DRAM, PCH 1.0V, VCCIO, VCCST,
•
VCCSA, VCCPLL, CPU Internal PLL, GT PLL, Ring PLL, System Agent PLL, Memory Controller PLL Voltage Multi­adjustment
Temperature Sensing: CPU, CPU/Water Pump, Chassis/Wa-
•
ter Pump Fans Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water
•
Pump Fans Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
•
ture): CPU, CPU/Water Pump, Chassis/Water Pump Fans Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/
•
Water Pump Fans Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,
•
VPPM, PCH 1.0V, VCCSA, VCCST, VCCIO
English
10
OS
Certica­tions
Microso® Windows® 10 64-bit
•
FCC, CE
•
ErP/EuP ready (ErP/EuP ready power supply is required)
•
Page 13
* For detailed product information, please visit our website: http://www.asrock .com
Please realize that the re is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. O verclocking may aect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your ow n risk and expense. We are not responsible for possible damage caused by overclocking.
Z390 Extreme4
11
English
Page 14
Chapter 2 Installation
is is an ATX form factor motherboard. Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings.
Make sure to unplug the power cord before installing or removing the motherboard
•
components. Failure to do so may cause physical injuries and damages to motherboard components. In order to avoid damage from static electricity to the motherboard’s components,
•
NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components. Hold components by the edges and do not touch the ICs.
•
Whenever you uninstall any components, place them on a grounded anti-static pad or
•
in the bag that comes with the components. When placing screws to secure the motherboard to the chassis, please do not over-
•
tighten the screws! Doing so may damage the motherboard.
English
12
Page 15
2.1 Installing the CPU
1. Before you insert the 1151-Pin CPU into the socket, please check if the P nP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the sock et. Do not force to in sert the CPU into the socket if above situation is found . Otherwise, the CPU will be seriously damaged.
2. Unplug all power cables before in stalling the CPU.
1
Z390 Extreme4
A
B
2
English
13
Page 16
3
4
English
14
5
Page 17
Please save and replace the cover if the processor i s removed. e cover must be placed if you wish to return the motherboard for aer service.
Z390 Extreme4
15
English
Page 18
2.2 Installing the CPU Fan and Heatsink
1 2
English
16
FAN
CPU_
Page 19
Z390 Extreme4
2.3 Installing Memory Modules (DIMM)
is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology.
1. For dual channel conguration , you always need to in stall identical (the same brand, speed , size and chip-type) DDR4 DIMM pairs.
2. It is unable to activate Dual Channel Memor y Technology with only one or three memory module installed.
3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and DIMM may be damaged.
Dual Channel Memory Conguration
Priority DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2
1 Populated Populated 2 Populated Populated Populated Populated
e DIMM only ts in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
17
English
Page 20
1
2
English
18
3
Page 21
2.4 Expansion Slots (PCI Express Slots)
ere are 6 PCI Express slots on the motherboard.
Before installing an ex pansion card, please make sure that the power supply is switched o or the power cord is unplugged. Please re ad the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.
PCIe slots:
PCIE1 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards. PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x8 lane width graphics cards. PCIE5 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE6 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.
PCIe Slot Congurations
PCIE2 PCIE4 PCIE6
Z390 Extreme4
Single Graphics Card x16 N/A N/A
Two Graphics Cards in
CrossFireXTM or SLITM
Mode
ree Graphics Cards in
3-Way CrossFireXTM Mode
For a better ther mal environment, please connect a ch assis fan to the motherboard’s chassis fan connector (CHA_ FAN1/WP, CHA_ FA N2/WP or CH A_FAN3/WP) when using multiple graphics cards.
x8 x8 N/A
x8 x8 x4
English
19
Page 22
2.5 Jumpers Setup
e illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”.
English
Clear CMOS Jumper (CLRCMO S1) (see p.1, No. 29)
CLRCMOS1 allows you to clear the data in CMOS. e data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn o the computer and unplug the power cord, then use a jumper cap to short the pins on CLRCMOS1 for 3 seconds. Please remember to remove the jumper cap aer clearing the CMOS. If you need to clear the CMOS when you just nish updating the BIOS, you must boot up the system rst, and then shut it down before you do the clear-CMOS action.
2-pin Jumper
Short: Clear CMOS Open: Default
20
Page 23
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these heade rs and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.
Z390 Extreme4
System Panel Header (9-pi n PANEL1) (see p.1, No. 17)
PWRBTN (Power Button):
Connec t to the power button on the chassi s front panel. You may congure the way to tur n o your system using the power button.
RESET (Reset B utton): Connec t to the reset button on the chassi s front panel. Press the reset button to restart the computer if the computer f reezes and fails to per form a normal restar t.
PLED (Syste m Power LED): Connec t to the power status indicator on the chassis front panel. e LED i s on when the system is operating. e LED keeps blinking when the system is in S1/S3 sleep state. e LED is o when the system is in S4 slee p state or powered o (S5).
HDLED (Ha rd Drive Activity LED): Connec t to the hard drive activity LED on the chassis front panel. e LED is on when the hard drive is reading or wr iting data.
e front panel design may dier by chassis. A front panel module mainly consists of powe r button, reset button , power LED, hard dr ive activity LED, speaker and etc. When connect­ing your chassi s front panel module to thi s header, make sure the wire a ssignments and the pin assignments are matched correctly.
1
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Connect the power button, reset button and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
21
English
Page 24
Power LED and Speaker
1
+5V
DUMMY
PLED+
PLED+
PLED-
DUMMY
SPEAKER
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
Header (7-pin SPK_PLED1) (see p.1, No. 18)
Please connect the chassis power LED and the chassis speaker to this header.
Serial ATA3 Connectors (SATA3_4_5: see p.1, No. 11) (SATA3_2_3: see p.1, No. 12) (SATA3_0_1: see p.1, No. 13) (SATA3_A1_A2: see p.1, No. 14)
USB 2.0 Headers (9-pin USB_1_2) (see p.1, No. 20) (9-pin USB_3_4) (see p.1, No. 19)
SATA3_2SATA3_0
SATA3_A1 SATA3_4
ese eight SATA3 connectors support SATA data cables for internal storage devices with up to
6.0 Gb/s data transfer rate. * M2_1, SATA3_0 and
SATA3_3SATA3_1
SATA3_1 share lanes. If either one of them is in use, the others will be disabled. * M2_2, SATA3_4 and SATA3_5 share lanes. If either one of them is in use, the others will be
SATA3_A2 SATA3_5
disabled. *To minimize the boot time, use Intel® Z390 SATA ports (SATA3_0) for your SSDs.
ere are two headers on this motherboard. Each USB 2.0 header can support two ports.
English
22
Page 25
Z390 Extreme4
1
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
USB 3.1 Gen1 Headers (19-pin USB3_5_6) (see p.1, No. 8) (19-pin USB3_7_8) (see p.1, No. 9)
Front Panel Type C USB
3.1 Gen1 Header (26-pin USB31_TC_2) (see p.1, No. 10)
Front Panel Audio Header (9-pin HD_ AUDIO1) (see p.1, No. 28)
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
IntA_PB_SSTX+
GND
IntA_PB_D-
IntA_PB_D+
Dummy
ere are two headers on this motherboard. Each USB 3.1 Gen1 header can support two ports.
ere is one Front Panel Type C USB 3.1 Gen1 Header on this motherboard. is header is used for connecting a USB 3.1 Gen1 module for additional USB 3.1 Gen1 ports.
is header is for connecting audio devices to the front audio panel.
1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must sup­port HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system.
2. If you use an AC’97 audio panel , please install it to the front panel audio header by the steps below: A. Connect Mic_IN (MIC) to MIC2_ L. B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L. C. Connect Ground (GND) to Ground (GND). D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to connect them for the AC’97 audio panel . E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and adjust “Recording Volume”.
English
23
Page 26
Chassis/Water Pump Fan
GN
OL
FA
FAN_SPEED_CONTROL
1 2 3 4
GND
OL
GND
OL
Connectors (4-pin CHA_FAN1/WP) (see p.1, No. 30)
(4-pin CHA_FAN2/WP) (see p.1, No. 23)
(4-pin CHA_FAN3/WP) (see p.1, No. 16)
FAN_VOLTAGE
FAN_SPEED
1 2 3 4
FAN_VOLTAGE
FAN_SPEED
1 2 3 4
D
FAN_VOLTAGE
FAN_SPEED
FAN_SPEED_CONTR
1 2 3 4
FAN_SPEED_CONTR
FAN_SPEED_CONTR
is motherboard provides three 4-Pin water cooling
chassis
fan connectors. If you plan to connect a 3-Pin
chassis water cooler fan, please connect it to Pin 1-3.
English
24
CPU Fan Connector (4-pin CPU_FAN1) (see p.1, No. 3)
CPU/Water Pump Fan Connector (4-pin CPU_FAN2/WP) (see p.1, No. 4)
ATX Power Connector (24-pin ATXPWR1) (see p.1, No. 7)
CPU_FAN_SPEED
FAN_VOLTAGE
N_SPEED_CONTROL
CPU_FAN_SPEED
FAN_VOLTAGE
12
1
GND
is motherboard provides a 4-Pin CPU fan (Quiet Fan) connector. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3.
is motherboard
4
provides a 4-Pin water
3
2
cooling CPU fan
1
GND
connector. If you plan to connect a 3-Pin CPU water cooler fan, please connect it to Pin 1-3.
24
is motherboard pro­vides a 24-pin ATX power connector. To use a 20-pin ATX power supply, please plug it along Pin 1 and Pin
13
13.
Page 27
Z390 Extreme4
4 1
8 5
1
1
SMB _DA TA_ MAI N
#
ATX 12V Power Connector (8-pin ATX12V1) (see p.1, No. 1)
ATX 12V Power Connector (4-pin ATX12V2) (see p.1, No. 2)
underbolt AIC Connectors (5-pin TB1) (see p.1, No. 24)
Serial Port Header (9-pin COM1) (see p.1, No. 21)
RRXD1
DDTR#1
TTXD1
DDCD#1
DDSR#1
CCTS#1
RRTS#1
GND
RRI#1
is motherboard provides an 8-pin ATX 12V power connector. To use a 4-pin ATX power supply, please plug it along Pin 1 and Pin 5.
Please connect an ATX 12V power supply to this connector. *e power supply plug ts into this connector in only one orientation.
Please connect a underbolt™ add-in card (AIC) to the underbolt AIC connector via the GPIO cable. *Please install the underbolt™ AIC card to PCIE6 (default slot).
is COM1 header supports a serial port module.
TPM Header (17-pi n TPMS1) (see p.1, No. 22)
is connector supports Trusted Platform Module (TPM) system,
GN D
LAD 0
+3 V
+3V S B
D
GN
GN D
LAD 1
SER IRQ #
S_P WRD WN #
PC ICL K
LAD 3
PC IRS T
FRA M E
GN D
LAD 2
which can securely store keys,
1
digital certicates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and
SMB _CL K_M AIN
ensures platform integrity.
English
25
Page 28
RGB LED Headers
1
1
Button
OCLED -
(4-pin RGB_LED1) (see p.1, No. 26) (4-pi n RGB _LED2) (see p.1, No. 25)
12V GRB
RGB header is used to connect RGB LED extension cable which allows users to choose from vari­ous LED lighting eects.
Caution: Never install the RGB
LED cable in the wrong orienta-
tion; otherwise, the cable may
be damaged.
*Please refer to page 33 for further instructions on this header.
English
Addressable LED Header (3-pin A DDR_LE D1) (see p.1, No. 27)
Performance Mode / Easy OC Header (4-pi n PM_O C) (see p.1, No. 15)
VOUT
1
Button-
DO_ADDR
+
OCLED+
GND
is header is used to connect Addressable
LED extension cable which allows users to choose from various LED lighting eects.
Caution: Never install the
Addressable LED cable in the
wrong orientation; otherwise,
the cable may be damaged.
*Please refer to page 34 for further instructions on this header.
Please connect the OC switch and OC LED indicator on the chassis to this header according to the pin assignments. Note the positive and negative pins before connecting the cables.
26
Page 29
Z390 Extreme4
2.7 M.2 WiFi/BT Module and Intel® CNVi (Integrated WiFi/BT) Installation Guide
e M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. e M.2 Socket (Key E) supports type 2230 WiFi/BT module and Intel® CNVi (Integrated WiFi/BT). * e M.2 socket does not support SATA M.2 SSDs.
Before you install Intel® Integrated Connectivity (CNVi) module, be sure to turn o the AC power.
Installing the WiFi/BT module or Intel® CNVi (Integrated WiFi/BT)
Step 1
Prepare a type 2230 WiFi/BT module or Intel® CNVi (Integrated WiFi/BT) and the screw.
PCB Length: 3cm Module Type: Type2230
A
Step 2
Find the nut location to be used.
English
27
Page 30
Step 3
Gently insert the WiFi/BT module or Intel® CNVi (Integrated WiFi/ BT) into the M.2 slot. Please be aware that the module only ts in one
A
orientation.
English
20
o
A
Step 4
Tighten the screw with a screwdriver to secure the module into place. Please do not overtighten the screw as this might damage the module.
A
28
Page 31
Z390 Extreme4
5
2.8 M.2_SSD (NGFF) Module Installation Guide (M2_1 and M2_2)
The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. The Ultra M.2 Sockets (M2_1 and M2_2) support SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x4 (32 Gb/s). * M2_1, SATA3_0 and SATA3_1 share lanes. If either one of them is in use, the others will be disabled. * M2_2, SATA3_4 and SATA3_5 share lanes. If either one of them is in use, the others will be disabled.
Installing the M.2_SSD (NGFF) Module
e following is an example of installing M.2_SSD (NGFF) module into the M2_2.
Step 1
Prepare a M.2_SSD (NGFF) module and the screw.
4
3
Depending on the PCB type and length of your M.2_SSD (NGFF) module, nd the corresponding nut
Step 2
2
1
A
BCDE
location to be used.
No. 1 2 3 4 5
Nut Location A B C D E
PCB Length 3cm 4.2cm 6cm 8cm 11cm
Module Type Type 2230 Type 224 2 Type2 260 Ty pe 2280 Type 22110
English
29
Page 32
Step 3
1
Before installing a M.2 (NGFF) SSD
2
1
module, please loosen the screws to remove the M.2 heatsink.
Step4
Align and gently insert the M.2 (NGFF) SSD module into the M.2 slot. Please be aware that the M.2 (NGFF) SSD module only ts in one
ABCDE
orientation.
English
30
o
ABCDE
20
Step 5
Tighten the screw with a screwdriver to secure the module into place.
NUT1NUT2DE
Please do not overtighten the screw as this might damage the module.
Page 33
M.2_SSD (NGFF) Module Support List
Vendor Interface P/N
ADATA SATA3 AXNS330E-32GM-B ADATA SATA3 AXNS381E-128GM-B ADATA SATA3 AXNS381E-256GM-B ADATA SATA3 ASU800NS38-256GT-C ADATA SATA3 ASU800NS38-512GT-C ADATA PCIe3 x4 ASX7000NP-128GT-C ADATA PCIe3 x4 ASX8000NP-256GM-C ADATA PCIe3 x4 ASX7000NP-256GT-C ADATA PCIe3 x4 ASX8000NP-512GM-C ADATA PCIe3 x4 ASX7000NP-512GT-C Apacer PCIe3 x4 AP240GZ280 Corsair PCIe3 x4 CSSD-F240GBMP500 Crucial SATA3 CT120M500SSD4 Crucial SATA3 CT240M500SSD4 Intel SATA3 Intel SSDSCKGW080A401/80G Intel PCIe3 x4 SSDPEKKF256G7 Intel PCIe3 x4 SSDPEKKF512G7 Kingston SATA3 SM2280S3 Kingston PCIe3 x4 SKC1000/480G Kingston PCIe2 x4 SH2280S3/480G OCZ PCIe3 x4 RVD400-M2280-512G (NVME) PATR IOT PCIe3 x4 PH240GPM280SSDR NVME Plextor PCIe3 x4 PX-128M8PeG Plextor PCIe3 x4 PX-1TM8PeG Plextor PCIe3 x4 PX-256M8PeG Plextor PCIe3 x4 PX-512M8PeG Plextor PCIe PX-G256M6e Plextor PCIe PX-G512M6e Samsung PCIe3 x4 SM961 MZVPW128HEGM (NVM) Samsung PCIe3 x4 PM961 MZVLW128HEGR (NVME) Samsung PCIe3 x4 960 EVO (MZ-V6E250) (NVME) Samsung PCIe3 x4 960 EVO (MZ-V6E250BW) (NVME) Samsung PCIe3 x4 SM951 (NVME) Samsung PCIe3 x4 SM951 (MZHPV256HDGL) Samsung PCIe3 x4 SM951 (MZHPV512HDGL) Samsung PCIe3 x4 SM951 (NVME) Samsung PCIe x4 XP941-512G (MZHPU512HCGL) SanDisk PCIe SD6PP4M-128G SanDisk PCIe SD6PP4M-256G Team SATA3 TM4PS4128GMC105 Team SATA3 TM4PS4256GMC105 Team SATA3 TM8PS4128GMC105 Team SATA3 TM8PS 4256GMC105
Z390 Extreme4
English
31
Page 34
TEAM PCIe3 x4 TM8FP2240G0C101 TEAM PCIe3 x4 TM8FP2480GC110 Transcend SATA3 TS256GMTS400 Transcend SATA3 TS512GMTS600 Transcend SATA3 TS512GMTS800 V-Color SATA3 VLM100-120G-2280B-RD V-Color SATA3 V LM100-240G-2280RGB V-Color SATA3 VSM100-24 0G-2280 V-Color SATA3 V LM100-240G-2280B-RD WD SATA3 WDS100T1B0B-00AS40 WD SATA3 WDS240G1G0B-00RC30 WD PCIe3 x4 WDS256G1X0C-00ENX0 (NVME) WD PCIe3 x4 WDS512G1X0C-00EN X0 (NVME)
For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for details: http://www.asrock.com
English
32
Page 35
Z390 Extreme4
1
1
2.9 ASRock Polychrome RGB
ASRock Polychrome RGB is a lighting control utility specically designed for unique individuals with sophisticated tastes to build their own stylish colorful lighting system. Simply by connect­ing the LED strip, you can customize various lighting schemes and patterns, including Static,
Breathing, Strobe, Cycling, Music, Wave and more.
Connecting the LED Strip
Connect your RGB LED strips to the motherboard.
RGB LED Headers (RGB_LED1, RGB_LED2)
1
B
R
G
V
2
1
RGB_LED1
12V GRB
RGB_LED2
on the
12V GRB
1. Never install the RGB LED cable in the wrong orientation; otherwise, the cabl e may be damaged.
2. Before installing or removing your RGB LED cable, please power o your system and unplug the power cord from the power supply. Failure to do so may c ause damages to motherboard components.
1. Please note that the RGB LED strips do not come with the package.
2. e RGB LED header supports standard 5050 RGB LED strip (12V/G/R/B), with a
maximum power rating of 3A (12V) and length within 2 meters.
English
33
Page 36
Connecting the Addressable RGB LED Strip
D
1
Connect your the motherboard.
Addressable RGB LED
strip to the
Addressable LED Header (ADDR_ LED1)
1
1. Never install the RGB LED cable in the wrong orientation; otherwise, the cabl e may be damaged.
2. Before installing or removing your RGB LED cable, please power o your system and unplug the power cord from the power supply. Failure to do so may c ause damages to motherboard components.
ADDR_LED1
GN
DO_ADDR
VOUT
on
1. Please note that the RGB LED strips do not come with the package.
2. e RGB LED header supports WS2812B addressable RGB LED strip (5V/Data/
GND), with a ma ximum power rating of 3A (5V) and length within 2 meters.
English
34
Page 37
ASRock Polychrome RGB Utility
Now you can adjust the RGB LED color through the ASRock Polychrome RGB Utility. Download this utility from the ASRock Live Update & APP Shop and start coloring your PC style your way!
Drag the tab to customize your preference.
Toggle on/o the RGB LED switch
Sync RGB LED eects for all LED regions of the motherboard
Select a RGB LED light eect from the drop-down menu.
Z390 Extreme4
35
English
Page 38
1 Einleitung
Vielen Dank, dass Sie sich für das Z390 Extreme4 von ASRock entschieden haben – ein zuverlässiges Motherboard, das konsequent unter der strengen Qualitätskontrolle von ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung mit robustem Design, das ASRock Streben nach Qualität und Beständigkeit erfüllt.
Da die technischen Daten des Motherboards sowie die BIOS-Soware aktualisiert werden können, kann der Inhalt dieser Dokumentation ohne Ankündigung geändert werden. Falls diese Dokumentation irgendwelchen Änderungen unterliegt, wird die aktualisierte Version ohne weitere Hinweise auf der ASRock-Webseite zur Verfügung gestellt. Sollten Sie technische Hilfe in Bezug auf dieses Motherboard benötigen, erhalten Sie auf unserer Webseite spezi­schen Informationen über das von Ihnen verwendete Modell. Auch nden Sie eine aktuelle Liste unterstützter VGA-Karten und Prozessoren auf der ASRock-Webseite: ASRock-Webseite http://www.asrock.com.
1.1 Lieferumfang
ASRock Z390 Extreme4-Motherboard (ATX-Formfaktor)
•
ASRock Z390 Extreme4–Schnellinstallationsanleitung
•
ASRock Z390 Extreme4–Support-CD
•
1 x E/A-Blendenabschirmung
•
4 x Serial-ATA-(SATA) Datenkabel (optional)
•
1 x ASRock SLI_HB_Bridge_2S-Karte (optional)
•
3 x Schrauben für M.2-Sockel (optional)
•
Deutsch
36
Page 39
1.2 Technische Daten
ATX-Formfaktor
Plattform
Prozessor
Chipsatz
Speicher
•
Unterstützt Intel® CoreTM-Prozessoren (Sockel 1151) der 8ten &
•
9ten Generation Digi Power design
•
12-Leistungsphasendesign
•
Unterstützt Intel® Turbo Boost 2.0-Technologie
•
Unterstützt CPUs mit freiem Multiplikator der Intel® K-Serie
•
Unterstützt ASRock BCLK-Übertaktung (voller Bereich)
•
Intel® Z390
•
Dualkanal-DDR4-Speichertechnologie
•
4 x DDR4-DIMM-Steckplätze
•
Unterstützt DDR4 4300+(OC)*/4266(OC)/4133(OC)/4000
•
(OC)/3866(OC)/3800(OC)/3733(OC)/3600(OC)/3200(OC) /2933(OC)/2800(OC)/2666/2400/2133 non-ECC,
ungepuerter Speicher * Weitere Informationen nden Sie in der Speicherkompatibilitätsliste auf der ASRock-Webseite. (http://www.asrock.com/)
Unterstützt ECC-UDIMM-Speichermodule (Betrieb im non-
•
ECC-Modus)
Systemspeicher, max. Kapazität: 64GB
•
Unterstützt Intel® Extreme Memory Prole (XMP) 2.0
•
15-μ-Goldkontakt in DIMM-Steckplätze
•
Z390 Extreme4
Erweiter­ungssteck­platz
3 x PCI-Express 3.0-x16-Steckplätze (PCIE2/PCIE4/
•
PCIE6:einzeln bei x16 (PCIE2); doppelt bei x8 (PCIE2) / x8
(PCIE4); dreifach bei x8 (PCIE2) / x8 (PCIE4) / x4 (PCIE6))* * Unterstützt NVMe-SSD als Bootplatte
3 x PCI-Express 3.0-x1-Steckplätze (Flexible PCIe)
•
Unterstützt AMD Quad CrossFireXTM, 3-Wege-CrossFireXTM
•
und CrossFireXTM
Unterstützt NVIDIA® Quad SLITM und SLI
•
1 x M.2-Sockel (Key E), unterstützt Typ-2230-Wi-Fi-/-BT-
•
Modul und Intel® CNVi (WLAN/BT integriert)
15-μ-Goldkontakt in VGA-PCIe-Steckplatz (PCIE2)
•
TM
Deutsch
37
Page 40
Grakkarte
Integrierte Intel® UHD Graphics-Visualisierung und VGA-
•
Ausgänge können nur mit Prozessoren unterstützt werden, die GPU-integriert sind. Unterstützt integrierte Intel® UHD Graphics-Visualisierung:
•
Intel® Quick Sync Video mit AVC, MVC (S3D) und MPEG-2 Full HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® UHD Graphics DirectX 12
•
HWA encodieren/decodieren: AVC/H.264, HEVC/H.265
•
8 bit, HEVC/H.265 10 bit, VP8, VP9 8 bit, VP9 10 bit (nur Dekodierung), MPEG2, MJPEG, VC-1 (nur Dekodierung) Drei Grakkarten-Ausgangsoptionen: D-Sub, HDMI und
•
DisplayPort 1.2 Unterstützt drei Monitore
•
Unterstützt HDMI mit maximaler Auösung von
•
4K x 2K (4096 x 2160) bei 30 Hz Unterstützt DisplayPort 1.2 mit maximaler Auösung
•
von 4K x 2K (4096 x 2304) bei 60 Hz Unterstützt D-Sub mit maximaler Auösung von
•
1920 x 1200 bei 60 Hz Unterstützt Auto-Lippensynchronizität, hohe Farbtiefe (12
•
bpc), xvYCC und HBR (Audio mit hoher Bitrate) mit HDMI
-Port (konformer HDMI-Monitor erforderlich) Unterstützt HDCP mit HDMI- und DisplayPort 1.2-Ports
•
Unterstützt 4K-Ultra-HD- (UHD) Wiedergabe mit HDMI-
•
und DIsplayPort-1.2-Ports
Deutsch
38
Audio
7.1-Kanal-HD-Audio mit Inhaltsschutz (Realtek ALC1220-
•
Audiocodec) Erstklassige Blu-ray-Audiounterstützung
•
Unterstützt Überspannungsschutz
•
Unterstützt Purity SoundTM 4
•
- Nichicon-Audiokappen der Fine Gold-Serie
- 120-dB-SRV-DAC mit Dierentialverstärker
- NE5532 – erstklassiger Headset-Verstärker für Audioanschluss an der Frontblende (unterstützt Headsets mit bis zu 600 Ohm)
- Reiner Stromeingang
Page 41
LAN
Rückblende, E/A
Z390 Extreme4
- Direct Drive Technology
- PCB-isolierte Abschirmung
- Impedanzerkennung am vorderen Ausgang
- Individuelle PCB-Layer für rechten/linken Audiokanal
- RGB-LED
- 15-μ-Gold-Audioanschluss Unterstützt DTS Connect
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Unterstützt Wake-On-LAN
•
Unterstützt Schutz gegen Blitzschlag/elektrostatische Entladung
•
Unterstützt energieezientes Ethernet 802.3az
•
Unterstützt PXE
•
2 x Antennenanschluss
•
1 x PS/2-Maus-/Tastaturanschluss
•
1 x D-Sub-Port
•
1 x HDMI-Port
•
1 x DisplayPort 1.2
•
1 x Optischer SPDIF-Ausgang
•
1 x USB-3.1-Gen2-Type-A-Port (10 Gb/s) (ReDriver)
•
(unterstützt Schutz gegen elektrostatische Entladung) 1 x USB-3.1-Gen2-Type-C-Port (10 Gb/s) (ReDriver)
•
(unterstützt Schutz gegen elektrostatische Entladung) 4 x USB-3.1 Gen1-Ports (Intel® Z390) (unterstützt Schutz gegen
•
elektrostatische Entladung) 1 x RJ-45-LAN-Port mit LED (Aktivität/Verbindung-LED und
•
Geschwindigkeit-LED) HD-Audioanschlüsse: Hintere Lautsprecher / Zentral / Bass /
•
Line-in / Vorderer Lautsprecher / Mikrofon
Speicher
6 x SATA-III-6,0-Gb/s-Abschluss, unterstützt RAID (RAID
•
0, RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology
16), NCQ, AHCI und Hot-Plugging* 2 x SATA-III-6,0-Gb/s-Anschlüsse von ASMedia ASM1061,
•
unterstützt NCQ, AHCI und Hot-Plugging
Deutsch
39
Page 42
Deutsch
Anschluss
* M2_1, SATA3_0 und SATA3_1 nutzen Lanes gemeinsam. Wenn einer von ihnen benutzt wird, werden die anderen deaktiviert. * M2_2, SATA3_4 und SATA3_5 nutzen Lanes gemeinsam. Wenn einer von ihnen benutzt wird, werden die anderen deaktiviert.
1 x Ultra-M.2-Sockel (M2_1), unterstützt M-Key-Typ-
•
2230/2242/2260/2280-M.2-SATA-III-6,0-Gb/s-Modul und M.2-PCI-Express-Modul bis Gen. 3 x 4 (32 Gb/s)** 1 x Ultra-M.2-Sockel (M2_2), unterstützt M-Key-Typ-
•
2230/2242/2260/2280/22110-M.2-SATA-III-6,0-Gb/s-Modul
und M.2-PCI-Express-Modul bis Gen. 3 x 4 (32 Gb/s)** ** Unterstützt Intel® OptaneTM-Technologie ** Unterstützt NVMe-SSD als Bootplatte ** Unterstützt ASRock U.2-Kit
1 x COM-Anschluss-Stileiste
•
1 x TPM-Stileiste
•
1 x Betrieb-LED- und Lautsprecher-Stileiste
•
2 x RGB-LED-Stileisten
•
* Unterstützt insgesamt bis zu 12 V/3 A, 36-W-LED-Streifen
1 x Adressierbare-LED-Stileiste
•
* Unterstützt insgesamt bis zu 5 V/3 A, 15-W-LED-Streifen
1 x CPU-Lüeranschluss (4-polig)
•
* Der CPU-Lüeranschluss unterstützt einen CPU-Lüer mit einer maximalen Lüerleistung von 1 A (12 W).
1 x Anschluss für CPU-/Wasserpumpenlüer (4-polig) (intelli-
•
gente Lüergeschwindigkeitssteuerung) * Der CPU-/Wasserpumpenlüer unterstützt einen Wasserkühler­lüer mit einer maximalen Lüerleistung von 2A (24 W).
3 x Anschlusse für Gehäuse-/Wasserpumpenlüer (4-polig)
•
(intelligente Lüergeschwindigkeitssteuerung) * Der Gehäuse-/Wasserpumpenlüer unterstützt einen Was­serkühlerlüer mit einer maximalen Lüerleistung von 2A (24 W). * CPU_FAN2/WP, CHA_FAN1/WP, CHA_FAN2/WP und CHA_ FAN3/WP können automatisch erkennen, ob ein 3- oder 4-poliger Lüer verwendet wird.
1 x 24-poliger ATX-Netzanschluss (hochdichter Netzan-
•
schluss).
1 x 8-poliger 12-V-Netzanschluss (hochdichter Netzanschluss)
•
40
Page 43
BIOS-Funk­tion
Z390 Extreme4
1 x 4-poliger 12-V-Netzanschluss (hochdichter Netzanschluss)
•
1 x Audioanschluss an der Frontblende (15μ goldene Audioan-
•
schluss) 1 x underbolt Erweiterungskartenanschluss (5-polig)
•
2 x USB 2.0-Stileisten (unterstützt 4 USB 2.0-Ports) (Intel®
•
Z390) (unterstützt Schutz gegen elektrostatische Entladung) 2 x USB 3.1 Gen1-Stileiste (unterstützt vier USB 3.1 Gen1-
•
Ports) (ASMedia ASM1074-Hub) (unterstützt Schutz gegen elektrostatische Entladung) 1 x USB-3.1-Gen1-Type-C-Stileiste an der Frontblende (Intel®
•
Z390) (unterstützt Schutz gegen elektrostatische Entladung) 1 x Leistungsmodus / einfache Übertaktungsstileiste
•
2 x AMI-UEFI-Legal-BIOS mit Unterstützung mehrsprachiger
•
grascher Benutzerschnittstellen (1 x Haupt-BIOS und 1 x Ausfall-BIOS) Unterstützt UEFI-Technologie (zuverlässige Sicherung)
•
ACPI 6.0-konforme Aufweckereignisse
•
SMBIOS 2.7-Unterstützung
•
CPU-Kern/Cache, GT, DRAM, PCH 1,0 V, VCCIO, VCCST,
•
VCCSA, VCCPLL, CPU intern PLL, GT PLL, Ring-PLL, Sys­temagent-PLL, Speichercontroller-PLL Spannungsmehrfachan­passung
Hard­wareüberwa­chung
Betriebssys­tem
Zertizierun­gen
Temperaturerkennung: CPU-, CPU-/Wasserpumpen-, Ge-
•
häuse-/Wasserpumpenlüer Lüertachometer: CPU-, CPU-/Wasserpumpen-, Gehäuse-/
•
Wasserpumpenlüer Lautloser Lüer (automatische Anpassung der Gehäuselüerg-
•
eschwindigkeit durch CPU-Temperatur): CPU-, CPU-/Wasser­pumpen-, Gehäuse-/Wasserpumpenlüer Mehrfachgeschwindigkeitssteuerung: CPU-, CPU-/Wasser-
•
pumpen-, Gehäuse-/Wasserpumpenlüer Spannungsüberwachung: +12 V, +5 V, +3,3 V, CPU Vcore,
•
DRAM, VPPM, PCH 1,0V, VCCSA, VCCST, VCCIO
Microso® Windows® 10, 64 Bit
•
FCC, CE
•
ErP/EuP ready (ErP/EuP ready-Netzteil erforderlich)
•
Deutsch
41
Page 44
* Detaillierte Produktinformationen nden Sie auf unserer Webseite: http://www.asrock.com
Bitte beachten Sie, dass mit einer Übertaktung, zu der die Anpassung von BIOS-Einstellungen, die Anwendung der Untied Overclocking Technology oder die Nutzung von Übertaktungswerkzeugen von Drittanbietern zählen, bestimmte Risiken verbunden sind. Eine Übertaktung kann sich auf die Stabilität Ihres Systems auswirken und sogar Komponenten und Geräte Ihres Systems beschädigen. Sie sollte auf eigene Gefahr und eigene Kosten durchgeführt werden. Wir übernehmen keine Verant­wortung für mögliche Schäden, die durch eine Übertaktung verursacht wurden.
Deutsch
42
Page 45
Z390 Extreme4
1.3 Jumpereinstellung
Die Abbildung zeigt, wie die Jumper eingestellt werden. Wenn die Jumper-Kappe auf den Kontakten angebracht ist, ist der Jumper „kurzgeschlossen“. Wenn keine Jumper-Kappe auf den Kontakten angebracht ist, ist der Jumper „oen“.
CMOS-löschen-Jumper (CLRCMOS1) (siehe S. 1, Nr. 29)
CLRCMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Die Daten im CMOS beinhaltet Systemeinrichtungsinformationen, wie Systemkennwort, Datum, Zeit und Systemeinrichtungsparameter. Zum Löschen und Rücksetzen der Systemparameter auf die Standardeinrichtung schalten Sie den Computer bitte ab und ziehen das Netzkabel; schließen Sie dann die Kontakte an CLRCMOS1 3 Sekunden mit einer Jumper-Kappe kurz. Bitte denken Sie daran, die Jumper-Kappe nach der CMOS-Löschung zu entfernen. Falls Sie den CMOS direkt nach Abschluss der BIOS-Aktualisierung löschen müssen, starten Sie das System zunächst; fahren Sie es dann vor der CMOS-Löschung herunter.
2-poliger Jumper
Kurzgeschlossen: CMOS löschen Oen: Standard
Deutsch
43
Page 46
1.4 Integrierte Stiftleisten und Anschlüsse
1
Integrierte Stileisten und Anschlüsse sind KEINE Jumper. Bringen Sie KEINE Jumper-Kappen an diesen Stileisten und Anschlüssen an. Durch Anbringen von Jumper-Kappen an diesen Stileisten und Anschlüssen können Sie das Motherboard dauerha beschädigen.
Deutsch
Systemblende-Stileiste (9-polig, PANEL1) (siehe S. 1, Nr. 17)
PWRBTN (Ein-/Austaste):
Mit der Ein-/Austaste an der Frontblende des Gehäuses verbinden. Sie können die Abschaltung Ihres Systems über die Ein-/Austaste kongurieren.
RESET (Reset-Taste):
Mit der Reset-Taste an der Frontblende des Gehäuses verbinden. Starten Sie den Computer über die Reset-Taste neu, wenn er abstürzt oder sich nicht normal neu starten lässt.
PLED (Systembetriebs-LED):
Mit der Betriebsstatusanzeige an der Frontblende des Gehäuses verbinden. Die LED leuchtet, wenn das System läu. Die LED blinkt, wenn sich das System im S1/S3-Ruhezustand bendet. Die LED ist aus, wenn sich das System im S4-Ruhezustand bendet oder ausgeschaltet ist (S5).
HDLED (Festplattenaktivitäts-LED):
Mit der Festplattenaktivitäts-LED an der Frontblende des Gehäuses verbinden. Die LED leuchtet, wenn die Festplatte Daten liest oder schreibt.
Das Design der Frontblende kann je nach Gehäuse variieren. Ein Frontblendenmodul besteht hauptsächlich aus Ein-/Austaste, Reset-Taste, Betrieb-LED, Festplattenaktivität-LED, Lautsprecher etc. Stellen Sie beim Anschließen Ihres Frontblendenmoduls an diese Stileiste sicher, dass Kabel- und Pinbelegung richtig abgestimmt sind.
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Verbinden Sie Ein-/Austaste, Reset-Taste und Systemstatusanzeige am Gehäuse entsprechend der nachstehenden Pinbelegung mit dieser Stileiste. Beachten Sie vor Anschließen der Kabel die positiven und negativen Kontakte.
44
Page 47
Z390 Extreme4
1
+5V
DUMMY
PLED+
PLED+
PLED-
DUMMY
SPEAKER
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
Betrieb-LED- und Lautsprecher-Stileiste (7-polig, SPK_PLED1) (siehe S. 1, Nr. 18)
Serial-ATA-III-Anschlüsse (SATA3_4_5: siehe S. 1, Nr. 11) (SATA3_2_3: siehe S. 1, Nr. 12) (SATA3_0_1: siehe S. 1, Nr. 13) (SATA3_A1_A2: siehe S. 1, Nr. 14)
SATA3_2SATA3_0
SATA3_A1 SATA3_4
Bitte verbinden Sie die Be­trieb-LED des Gehäuses und den Gehäuselautsprecher mit dieser Stileiste.
Diese acht SATA-III-Anschlüsse unterstützen SATA-Datenkabel für interne Speichergeräte mit einer Datenübertragungsgeschw indigkeit bis 6,0 Gb/s. * M2_1, SATA3_0 und SATA3_1
SATA3_3SATA3_1
nutzen Lanes gemeinsam. Wenn einer von ihnen benutzt wird, werden die anderen deaktiviert. * M2_2, SATA3_4 und SATA3_5 nutzen Lanes gemeinsam. Wenn einer von ihnen benutzt wird, werden die anderen deaktiviert. *Nutzen Sie zum Minimieren
SATA3_A2 SATA3_5
der Startzeit Intel®-Z390-SATA­Ports (SATA3_0) für Ihre SSDs.
USB 2.0-Stileisten (9-polig, USB_1_2) (siehe S. 1, Nr. 20) (9-polig, USB_3_4) (siehe S. 1, Nr. 19)
Es gibt zwei Stileisten an diesem Motherboard. Jede USB 2.0-Stileiste kann zwei Ports unterstützen.
Deutsch
45
Page 48
1
USB 3.1 Gen1-Stileisten
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
(19-polig, USB3_5_6) (siehe S. 1, Nr. 8) (19-polig, USB3_7_8) (siehe S. 1, Nr. 9)
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
IntA_PB_SSTX+
GND
IntA_PB_D-
IntA_PB_D+
Dummy
Es gibt zwei Stileisten an diesem Motherboard. Jede USB 3.1 Gen1­Stileiste kann zwei Ports unterstützen.
Deutsch
Type-C-USB-3.1 Gen1-Stileiste für die Frontblende (26-polig, USB31_TC_2) (siehe S. 1, Nr. 10)
Es gibt eine Type-C-USB-3.1 Gen1-Stileiste für die Frontblende an diesem Motherboard. Diese Stileiste dient dem Anschluss eines USB-3.1 Gen1-Moduls für zusätzliche USB-3.1 Gen1­Ports.
Audiostileiste (Frontblende) (9-polig, HD_AUDIO1) (siehe S. 1, Nr. 28)
1. High Denition Audio unterstützt Anschlusserkennung, der Draht am Gehäuse muss dazu jedoch HDA unterstützt. Bitte befolgen Sie zum Installieren Ihres Systems die Anweisungen in unserer Anleitung und der Anleitung zum Gehäuse.
2. Bei Nutzung eines AC’97-Audiopanels dieses bitte anhand folgender Schritte an der Audi­ostileiste der Frontblende installieren: A. Mic_IN (Mikrofon) mit MIC2_L verbinden. B. Audio_R (RIN) mit OUT2_R und Audio_L (LIN) mit OUT2_L verbinden. C. Erde (GND) mit Erde (GND) verbinden. D. MIC_RET und OUT_RET sind nur für das HD-Audiopanel vorgesehen. Sie müssen sie nicht für das AC’97-Audiopanel verbinden. E. Rufen Sie zum Aktivieren des vorderen Mikrofons das „FrontMic (Vorderes Mikro­fon)“-Register in der Realtek-Systemsteuerung auf und passen „Recording Volume (Aufnah­melautstärke)“ an.
Diese Stileiste dient dem Anschließen von Audiogeräten an der Frontblende.
46
Page 49
Z390 Extreme4
GN
OL
FA
FAN_SPEED_CONTROL
1 2 3 4
GND
OL
GND
OL
Gehäuse-/Wasserpump­en-Lüeranschlusse (4-polig, CHA_FAN1/WP) (siehe S. 1, Nr. 30)
(4-polig, CHA_FAN2/WP) (siehe S. 1, Nr. 23)
(4-polig, CHA_FAN3/WP) (siehe S. 1, Nr. 16)
CPU-Lüeranschluss (4-polig, CPU_FAN1) (siehe S. 1, Nr. 3)
CPU-/Wasserpumpen­Lüeranschluss (4-polig, CPU_FAN2/WP) (siehe S. 1, Nr. 4)
FAN_VOLTAGE
FAN_SPEED
FAN_SPEED_CONTR
1 2 3 4
FAN_VOLTAGE
FAN_SPEED
FAN_SPEED_CONTR
1 2 3 4
D
FAN_VOLTAGE
FAN_SPEED
FAN_SPEED_CONTR
1 2 3 4
CPU_FAN_SPEED
FAN_VOLTAGE
N_SPEED_CONTROL
CPU_FAN_SPEED
FAN_VOLTAGE
GND
GND
Dieses Motherboard bietet drei 4-poligen Wasserkühlung-Ge­häuselüeranschluss. Falls Sie einen 3-poligen Wasserkühlerlüer
Gehäuse-
anschließen möchten, verbinden Sie ihn bitte mit Kontakt 1 bis 3.
Dieses Motherboard bietet einen 4-poligen CPU-Lüeran­schluss (lautloser Lüer). Falls Sie einen 3-poligen CPU-Lüer anschließen möchten, verbinden Sie ihn bitte mit Kontakt 1 bis 3.
Dieses Motherboard bie-
4
tet einen 4-poligen Was-
3
2
serkühlung-CPU-Lüeran-
1
schluss. Falls Sie einen 3-poligen CPU-Wasserkühlerlüer an­schließen möchten, verbinden Sie ihn bitte mit Kontakt 1 bis 3.
ATX-Netzanschluss (24-polig, ATXPWR1) (siehe S. 1, Nr. 7)
12
24
Dieses Motherboard bietet einen 24-poligen ATX-Net­zanschluss. Bitte schließen Sie es zur Nutzung eines 20-pol­igen ATX-Netzteils entlang
1
13
Kontakt 1 und Kontakt 13 an.
Deutsch
47
Page 50
ATX-12-V-Netzanschluss
4 1
8 5
1
1
#
(8-polig, ATX12V1) (siehe S. 1, Nr. 1)
Dieses Motherboard bietet ei­nen 8-poligen ATX-12-V-Net­zanschluss. Bitte schließen Sie es zur Nutzung eines 4-poligen ATX-Netzteils entlang Kontakt 1 und Kontakt 5 an.
Deutsch
ATX-12-V-Netzanschluss (4-polig, ATX12V2) (siehe S. 1, Nr. 2)
underbolt­Erweiterungskarten anschlüsse (5-polig, TB1) (siehe S. 1, Nr. 24)
Serieller-Port-Stileiste (9-polig, COM1) (siehe S. 1, Nr. 21)
TPM-Stileiste (17-polig, TPMS1) (siehe S. 1, Nr. 22)
An diesen Anschluss schließen Sie ein ATX-12 V-Netzteil an. *Der Netzteilstecker passt nur in einer Richtung in diesen Anschluss.
Bitte verbinden Sie eine underbolt™-Erweiterungskarte über das GPIO-Kabel mit diesem underbolt-AIC-Anschluss. *Bitte installieren Sie die underbolt™-AIC-Karte am PCIE6 (Standardsteckplatz).
RRXD1
DDTR#1
DDSR#1
CCTS#1
Diese COM1-Stileiste unterstützt ein Modul für serielle Ports.
RRI#1
RRTS#1
GND
TTXD1
DDCD#1
Dieser Anschluss unterstützt das
GN D
LAD 0
LAD 3
+3 V
+3V S B
D
GN
SER IRQ #
S_P WRD WN #
PC IRS T
GN D
LAD 1
LAD 2
Trusted Platform Module-(TPM)
PC ICL K
FRA M E
System, das Schlüssel, digitale
1
Zertikate, Kennwörter und Dat-
GN D
en sicher auewahren kann. Ein TPM-System hil zudem bei der Stärkung der Netzwerksicherheit,
SMB _CL K_M AIN
schützt digitale Identitäten und gewährleistet die Plattforminteg­rität.
48
Page 51
Z390 Extreme4
1
D
1
Button
OCLED -
RGB-LED-Stileisten (4-polig, RGB_LED1) (siehe S. 1, Nr. 26) (4-polig, RGB_LED2) (siehe S. 1, Nr. 25)
Adressierbare-LED-Sti­leiste (3-polig, ADDR_LED1) (siehe S. 1, Nr. 27)
12V GRB
DO_ADDR
VOUT
RGB-Stileiste dient dem An­schließen eines RGB-LED-Erweit­erungskabels, das dem Nutzer die Auswahl zwischen verschiedenen LED-Lichteekten ermöglicht.
Achtung: Installieren Sie das
RGB-LED-Kabel niemals falsch
herum; andernfalls könnte das
Kabel beschädigt werden.
*Weitere Anweisungen zu dieser Stileiste nden Sie auf Seite 33.
Diese Stileiste dient der Verbind-
GN
ung des Adressierbare-LED-Ver­längerungskabels, womit Nutzer zwischen verschiedenen LED-Li­chteekten wählen können.
Achtung: Installieren Sie das
Adressierbare-LED-Kabel
niemals falsch herum; andern-
falls könnte das Kabel beschädigt
werden.
*Weitere Anweisungen zu dieser Stileiste nden Sie auf Seite 34.
Leistungsmodus / einfache Übertaktungsstileiste (4-polig, PM_OC) (siehe S. 1, Nr. 15)
1
Button-
+
OCLED+
Bitte verbinden Sie den Übertak­tungsschalter und die Übertak­tungs-LED-Anzeige am Gehäuse entsprechend der Pinbelegung mit dieser Stileiste. Beachten Sie vor Anschließen der Kabel die positiven und negativen Kontakte.
Deutsch
49
Page 52
1 Introduction
Nous vous remercions d’avoir acheté cette carte mère ASRock Z390 Extreme4, une carte mère able fabriquée conformément au contrôle de qualité rigoureux et constant appliqué par ASRock. Fidèle à son engagement de qualité et de durabilité, ASRock vous garantit une carte mère de conception robuste aux performances élevées.
Les spécications de la carte mère et du logiciel BIOS pouvant être mises à jour, le contenu de ce document est soumis à modication sans préavis. En cas de modications du présent document, la version mise à jour sera disponible sur le site Internet ASRock sans notication préalable. Si vous avez besoin d’une assistance technique pour votre carte mère, veuillez visiter notre site Internet pour plus de détails sur le modèle que vous utilisez. La liste la plus récente des cartes VGA et des proces­seurs pris en charge est également disponible sur le site Internet de ASRock. Site Internet ASRock http://www.asrock.com.
1.1 Contenu de l’emballage
Carte mère ASRock Z390 Extreme4 (facteur de forme ATX)
•
Guide d’installation rapide ASRock Z390 Extreme4
•
CD d’assistance ASRock Z390 Extreme4
•
1 x panneau de protection E/S
•
4 x câbles de données Serial ATA (SATA) (Optionnel)
•
1 x carte ASRock SLI_HB_Bridge_2S (Optionnel)
•
3 x vis pour sockets M.2 (Optionnel)
•
Français
50
Page 53
1.2 Spécications
Plateforme
Processeur
Chipset
Mémoire
•
•
•
•
•
•
•
•
•
•
•
* Veuillez consulter la liste de prise en charge des mémoires sur le site Web d'ASRock pour de plus amples informations. (http://www.asrock.com/)
•
•
•
•
Z390 Extreme4
Facteur de forme ATX
ème
Prend en charge les processeurs 8 CoreTM (socket 1151) Digi Power design Alimentation à 12 phases Prend en charge la technologie Intel® Turbo Boost 2.0 Prend en charge les processeurs débloqués de la série K Intel® Prend en charge l’overclocking ASRock BCLK Full-range
Intel® Z390
Technologie mémoire double canal DDR4 4 x fentes DIMM DDR4 Prend en charge les mémoires sans tampon non ECC DDR4 4300+(OC)*/4266(OC)/4133(OC)/4000(OC)/3866(OC)/ 3800(OC)/3733(OC)/3600(OC)/3200(OC)/2933(OC)/ 2800(OC)/2666/2400/2133
Prend en charge les modules mémoire UDIMM ECC (fonctionne en mode non-ECC) Capacité max. de la mémoire système : 64Go Prend en charge Intel® Extreme Memory Prole (XMP) 2.0 Contacts dorés 15μ sur fentes DIMM
ème
et 9
génération Intel®
Fente d’ex­pansion
3 x fentes PCI Express 3.0 x16 (PCIE2/PCIE4/PCIE6:Simple
•
en mode x16 (PCIE2) ; double en mode x8 (PCIE2) / x8 (PCIE4) ; triple en mode x8 (PCIE2) / x8 (PCIE4) / x4 (PCIE6))*
* Prend en charge les SSD NVMe comme disques de démarrage
3 x fentes PCI Express 3.0 x 1 (Flexible PCIe)
•
Prend en charge AMD Quad CrossFireXTM, 3-Way
•
CrossFireXTM et CrossFireXTM Prend en charge NVIDIA® Quad SLITM et SLI
•
1 x socket M.2 (Touche E), prend en charge les modules WiFi/
•
BT type 2230 et Intel® CNVi (WiFi/BT intégré) Contact doré 15μ dans fente VGA PCIe (PCIE2)
•
TM
Français
51
Page 54
Graphiques
La technologie Intel® UHD Graphics Built-in Visuals et
•
les sorties VGA sont uniquement prises en charge par les processeurs intégrant un contrôleur graphique. Prend en charge la technologie Intel® UHD Graphics Built-
•
in Visuals : Intel® Quick Sync Video avec AVC, MVC (S3D) et MPEG-2 Full HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® UHD Graphics DirectX 12
•
Codage/Décodage HWA : AVC/H.264, HEVC/H.265 8bits,
•
HEVC/H.265 10bits, VP8, VP9 8bits, VP9 10bits (Encodage uniquement), MPEG2, MJPEG, VC-1 (Encodage uniquement) Trois options de sortie graphique : D-Sub, HDMI et
•
DisplayPort 1.2 Prend en charge la conguration à triple moniteurs
•
Prend en charge la technologie HDMI avec résolution
•
maximale de 4K x 2K (4096x2160) @ 30Hz Prend en charge la technologie DisplayPort 1.2 avec résolution
•
maximale de 4K x 2K (4096x2304) @ 60Hz Prend en charge le mode D-Sub avec une résolution maximale
•
de 1920x1200 @ 60Hz Prend en charge les technologies Auto Lip Sync, Deep Color
•
(12bpc), xvYCC et HBR (High Bit Rate Audio) avec port HDMI (un écran compatible HDMI est requis) Prend en charge HDCP via ports HDMI et DisplayPort 1.2
•
Prend en charge la lecture 4K Ultra HD (UHD) avec les ports
•
HDMI et DisplayPort 1.2
Français
52
Audio
Audio 7.1 CH HD avec protection du contenu (codec audio
•
Realtek ALC1220) Compatible audio Blu-ray Premium
•
Prend en charge la protection contre les surtensions
•
Prend en charge Purity SoundTM 4
•
- Couvercles audio série en or n Nichicon
- 120dB SNR DAC avec amplicateur diérentiel
- Amplicateur de casque NE5532 Premium pour connecteur audio sur panneau avant (prend en charge les casques jusqu’à 600 Ohms)
- Entrée d’alimentation Pure Power
Page 55
Réseau
Connectique du panneau arrière
Z390 Extreme4
- Technologie Direct Drive
- Blindage isolant PCB
- Détection d'impédance sur le port de sortie avant
- Couches de PCB individuelles pour canal audio D/G
- LED RVB
- Connecteur audio or 15μ Prend en charge DTS Connect
•
Gigabit LAN 10/100/1000 Mo/s
•
Giga PHY Intel® I219V
•
Prend en charge la fonction Wake-On-LAN
•
Prend en charge la protection contre la foudre/les décharges
•
électrostatiques Prend en charge la fonction d’économie d’énergie Ethernet
•
802.3az Prend en charge PXE
•
2 x ports antenne
•
1 x port souris/clavier PS/2
•
1 x port D-Sub
•
1 x port HDMI
•
1 x DisplayPort 1.2
•
1 x port sortie optique SPDIF
•
1 x port USB 3.1 Gen2 Type A (10 Go/s) (ReDriver) (Protection
•
contre les décharges électrostatiques) 1 x port USB 3.1 Gen2 Type C (10 Go/s) (ReDriver) (Protection
•
contre les décharges électrostatiques) 4 x ports USB 3.1 Gen1 (Intel® Z390) (Protection contre les
•
décharges électrostatiques) 1 x port RJ-45 LAN avec LED (LED ACT/LIEN et LED
•
VITESSE) Connecteurs jack audio HD : Haut-parleur arrière / central /
•
basses / entrée ligne / haut-parleur avant / microphone
Français
Stockage
6 x connecteurs SATA3 6,0 Go/s, compatibles RAID (RAID 0,
•
RAID 1, RAID 5, RAID 10, technologies Intel Rapid Storage
16), NCQ, AHCI et «Hot Plug»* 2 x connecteurs SATA3 6,0 Go/s ASMedia ASM1061, compati-
•
bles avec NCQ, AHCI et «Hot Plug»
53
Page 56
Français
Connecteur
* Lignes partagées M2_1, SATA3_0 et SATA3_1. Si vous utilisez un connecteur, les autres seront désactivés. * Lignes partagées M2_2, SATA3_4 et SATA3_5. Si vous utilisez un connecteur, les autres seront désactivés.
1 x socket Ultra M.2 (M2_1), prend en charge les modules M.2
•
SATA3 6,0 Go/s type 2230/2242/2260/2280 touche M et M.2 PCI Express jusqu'à Gen3 x4 (32 Go/s)** 1 x socket Ultra M.2 (M2_2), prend en charge les modules M.2
•
SATA3 6,0 Go/s type 2230/2242/2260/2280/22110 touche M et
M.2 PCI Express jusqu'à Gen3 x4 (32 Go/s)** ** Prend en charge Intel® OptaneTM Technology ** Prend en charge les SSD NVMe comme disques de démarrage ** Prend en charge le kit ASRock U.2
1 x embase pour port COM
•
1 x embase TPM
•
1 x prise DEL d’alimentation et haut-parleur
•
2 x embase LED RVB
•
* Prend en charge les rubans LED jusqu'à 12 V/3 A, 36 W au total
1 x embase LED adressable
•
* Prend en charge les rubans LED jusqu'à 5 V/3 A, 15 W au total
1 x connecteur pour ventilateur de CPU (4 broches)
•
* Le connecteur pour ventilateur de CPU prend en charge un ventilateur de CPU d'une puissance maximale de 1 A (12 W).
1 x connecteur pour ventilateur de processeur /pompe à eau (4
•
broches) (contrôle de vitesse de ventilateur intelligent) * Le ventilateur de processeur /pompe à eau prend en charge un ventilateur de refroidisseur d'eau d'une puissance maximale de 2A (24 W).
3 x connecteurs pour ventilateur de châssis /pompe à eau (4
•
broches) (contrôle de vitesse de ventilateur intelligent) * Le ventilateur de châssis /pompe à eau prend en charge un venti­lateur de refroidisseur d'eau d'une puissance maximale de 2A (24 W). * CPU_FAN2/WP, CHA_FAN1/WP, CHA_FAN2/WP et CHA_ FAN3/WP peuvent détecter automatiquement si un ventilateur 3 broches ou 4 broches est utilisé.
1 x connecteur d’alimentation ATX 24 broches (connecteur
•
d’alimentation haute densité)
1 x connecteur d’alimentation 12V 8 broches (connecteur d’ali-
•
mentation haute densité)
54
Page 57
Caractéris­tiques du BIOS
Z390 Extreme4
1 x connecteur d’alimentation 12V 4 broches (connecteur d’ali-
•
mentation haute densité) 1 x Connecteur audio panneau avant (15μ Connecteur audio or)
•
1 x connecteur underbolt AIC (5 broches)
•
2 x embases USB 2.0 (4 ports USB 2.0 pris en charge) (Intel®
•
Z390) (Protection contre les décharges électrostatiques) 2 x embase USB 3.1 Gen1 (4 ports USB 3.1 Gen1 pris en charge)
•
(concentrateur ASMedia ASM1074) (Protection contre les décharges électrostatiques) 1 x embase USB 3.1 Gen1 Type C sur panneau avant (Intel®
•
Z390) (Protection contre les décharges électrostatiques) 1 x Embase mode Performances / OC facile
•
2 x BIOS UEFI AMI légaux avec prise en charge interface
•
graphique multilingue (1 x BIOS principal et 1 x BIOS de sauvegarde) Prend en charge la technologie de sauvegarde sécurisée UEFI
•
Compatible ACPI 6.0 Wake Up Events
•
Compatible SMBIOS 2.7
•
Réglage de la tension Noyau/Cache CPU, GT, DRAM, PCH 1,0
•
V, VCCIO, VCCST, VCCSA, VCCPLL, PLL interne CPU, PLL GT, PLL Ring, PLL Agent système, PLL Contrôleur mémoire
Surveillance du matériel
Système d’ex­ploitation
Certications
Détection de température : Ventilateurs de CPU, CPU /pompe
•
à eau, châssis /pompe à eau Tachymètre de ventilateur : Ventilateurs de CPU, CPU /pompe
•
à eau, châssis /pompe à eau Ventilateur silencieux (réglage automatique de la vitesse du
•
ventilateur du châssis d’après la température du CPU) : Ventila­teurs de CPU, CPU /pompe à eau, châssis /pompe à eau Contrôle simultané des vitesses du ventilateur : Ventilateurs de
•
CPU, CPU /pompe à eau, châssis /pompe à eau Surveillance de la tension d’alimentation : +12V, +5V, +3,3V,
•
CPU Vcore, DRAM, VPPM, PCH 1,0V, VCCSA, VCCST, VCCIO
Microso® Windows® 10 64 bits
•
FCC, CE
•
ErP/EuP Ready (alimentation ErP/EuP ready requise)
•
Français
55
Page 58
* pour des informations détaillées de nos produits, veuillez visiter notre site: http://www.asrock.com
Il est important de signaler que l’overclocking présente certains risques, incluant des modications du BIOS, l’application d’une technologie d’overclocking déliée et l’utilisation d’outils d’overclocking développés par des tiers. La stabilité de votre système peut être aectée par ces pratiques, voire provoquer des dommages aux composants et aux périphériques du système. L’overclocking se fait à vos risques et périls. Nous ne pourrons en aucun cas être tenus pour responsables des dommages éventuels provoqués par l’overclocking.
Français
56
Page 59
Z390 Extreme4
1.3 Conguration des cavaliers (jumpers)
L’illustration ci-dessous vous renseigne sur la conguration des cavaliers (jumpers). Lorsque le capuchon du cavalier est installé sur les broches, le cavalier est «court-circuité». Si le capuchon du cavalier n’est pas installé sur les broches, le cavalier est «ouvert».
Cavalier Clear CMOS (CLRCMOS1) (voir p.1, No. 29)
CLRCMOS1 vous permet d’eacer les donnés de la CMOS. Les données de la CMOS incluent les informations de conguration du système telles que mot de passe, date, heure et paramètres de réglage du système. Pour eacer les paramètres du système et rétablir les valeurs par défaut, veuillez éteindre votre ordinateur et débrancher son cordon d’alimentation; utilisez ensuite un capuchon de cavalier pour court-circuiter les broches CLRCMOS1 pendant 3 secondes. N’oubliez pas de retirer le capuchon du cavalier une fois les données CMOS eacées. Si vous avez besoin d’eacer les données CMOS après une mise à jour du BIOS, vous devez tout d’abord redémarrer le système, puis l’éteindre avant de procéder à l’eacement de la CMOS.
Cavalier (jumper) à 2 broches
Court-circuité: Fonction Clear CMOS Ouvert: Par défaut
Français
57
Page 60
1.4 Embases et connecteurs de la carte mère
1
Les embases et connecteurs situés sur la carte NE SONT PAS des cavaliers. Ne placez JAMAIS de capuchons de cavaliers sur ces embases ou connecteurs. Placer un capuchon de cavalier sur ces embases ou connecteurs endommagera irrémédiablement votre carte mère.
Français
Embase du panneau système (PANNEAU1 à 9 broches) (voir p.1, No. 17)
PWRBTN (bouton d’alimentation):
pour brancher le bouton d’alimentation du panneau frontal du châssis. Vous pouvez congurer la façon dont votre système doit s’arrêter à l’aide du bouton d'alimentation.
RESET (bouton de réinitialisation):
pour brancher le bouton de réinitialisation du panneau frontal du châssis. Appuyez sur le bou­ton de réinitialisation pour redémarrer l’ordinateur en cas de plantage ou de dysfonctionnement au démarrage.
PLED (LED d’alimentation du système) :
pour brancher le témoin d’état de l’alimentation du panneau frontal du châssis. Le LED est allumé lorsque le système fonctionne. Le LED clignote lorsque le système se trouve en mode veille S1/S3. Le LED est éteint lorsque le système se trouve en mode veille S4 ou hors tension (S5).
HDLED (LED d’activité du disque dur) :
pour brancher le témoin LED d’activité du disque dur du panneau frontal du châssis. Le LED est allumé lorsque le disque dur lit ou écrit des données.
La conception du panneau frontal peut varier en fonction du châssis. Un module de panneau frontal est principalement composé d’un bouton d'alimentation, d'un bouton de réinitialisation, d'un témoin LED d’alimentation, d'un témoin LED d’activité du disque dur, d'un haut-parleur etc. Lorsque vous reliez le module du panneau frontal de votre châssis sur cette embase, veillez à parfaitement faire correspondre les ls et les broches.
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Branchez le bouton de mise en marche, le bouton de réinitialisation et le témoin d’état du système présents sur le châssis sur cette embase en respectant la conguration des broches illustrée ci-dessous. Repérez les broches positive et négative avant de brancher les câbles.
58
Page 61
Z390 Extreme4
1
+5V
DUMMY
PLED+
PLED+
PLED-
DUMMY
SPEAKER
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
Prise DEL d’alimentation et haut-parleur (SPK_PLED1 à 7 broches) (voir p.1, No. 18)
Connecteurs Serial ATA3 (SATA3_4_5: voir p.1, No. 11) (SATA3_2_3: voir p.1, No. 12) (SATA3_0_1: voir p.1, No. 13) (SATA3_A1_A2: voir p.1, No. 14)
SATA3_2SATA3_0
SATA3_A1 SATA3_4
Veuillez brancher la DEL d'alimentation du châssis et le haut-parleur du châssis sur ce connecteur.
Ces huit connecteurs SATA3 sont compatibles avec les câbles de données SATA pour les appareils de stockage internes avec un taux de transfert maximal de 6,0 Go/s.
SATA3_3SATA3_1
* Lignes partagées M2_1, SATA3_0 et SATA3_1. Si vous utilisez un connecteur, les autres seront désactivés. * Lignes partagées M2_2, SATA3_4 et SATA3_5. Si vous utilisez un connecteur, les autres seront désactivés.
SATA3_A2 SATA3_5
* Pour minimiser le temps au démarrage, utilisez les ports Intel® Z390 SATA (SATA3_0) pour vos SSD.
Embases USB 2.0 (USB_1_2 à 9 broches) (voir p.1, No. 20) (USB_3_4 à 9 broches) (voir p.1, No. 19)
Cette carte mère comprend deux connecteurs. Chaque embase USB 2.0 peut prendre en charge deux ports.
Français
59
Page 62
1
Embases USB 3.1 Gen1
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
(USB3_5_6 à 19 broches) (voir p.1, No. 8) (USB3_7_8 à 19 broches) (voir p.1, No. 9)
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
IntA_PB_SSTX+
GND
IntA_PB_D-
IntA_PB_D+
Dummy
Cette carte mère comprend deux connecteurs. Chaque embase USB 3.1 Gen1 peut prendre en charge deux ports.
Français
Embase USB 3.1 Gen1 Type C sur panneau avant (USB31_TC_2 à 26 broches) (voir p.1, No. 10)
Cette carte mère comprend une embase USB 3.1 Gen1 Type C sur le panneau avant. Cette embase sert à connecter un module USB 3.1 Gen1 pour des ports USB 3.1 Gen1 supplémentaires.
Embase audio du panneau frontal (HD_AUDIO1 à 9 broches)
Cette embase sert au branchement des appareils audio au panneau audio frontal.
(voir p.1, No. 28)
1. L’audio haute dénition prend en charge la technologie Jack Sensing (détection de la che), mais le panneau grillagé du châssis doit être compatible avec la HDA pour fonctionner correctement. Veuillez suivre les instructions gurant dans notre manuel et dans le manuel du châssis pour installer votre système.
2. Si vous utilisez un panneau audio AC’97, veuillez le brancher sur l’embase audio du panneau frontal en procédant comme suit : A. branchez Mic_IN (MIC) sur MIC2_L. B. branchez Audio_R (RIN) sur OUT2_R et Audio_L (LIN) sur OUT2_L. C. branchez la mise à terre (GND) sur mise à terre (GND). D. MIC_RET et OUT_RET sont exclusivement réservés au panneau audio HD. Il est inutile de les brancher avec le panneau audio AC’97. E. Pour activer le micro frontal, sélectionnez l’onglet «FrontMic» du panneau de contrôle Realtek et réglez le paramètre «Volume d’enregistrement».
60
Page 63
Z390 Extreme4
GN
OL
FA
FAN_SPEED_CONTROL
1 2 3 4
GND
OL
GND
OL
Connecteurs du ventila­teur de châssis/pompe à eau (CHA_FAN1/WP à 4 broches) (voir p.1, No. 30)
(CHA_FAN2/WP à 4 broches) (voir p.1, No. 23)
(CHA_FAN3/WP à 4 broches) (voir p.1, No. 16)
Connecteur du ventilateur du processeur (CPU_FAN1 à 4 broches) (voir p.1, No. 3)
FAN_VOLTAGE
FAN_SPEED
1 2 3 4
FAN_VOLTAGE
FAN_SPEED
1 2 3 4
D
FAN_VOLTAGE
FAN_SPEED
1 2 3 4
CPU_FAN_SPEED
FAN_VOLTAGE
FAN_SPEED_CONTR
FAN_SPEED_CONTR
FAN_SPEED_CONTR
GND
Cette carte mère est dotée de trois connecteurs pour ventilateur de châssis
à refroidissement par eau à 4 broches. Si vous envisagez de connecter un ventilateur de refroidisseur d’eau pour
châssis
à 3 broches, veuillez le brancher sur la Broche 1-3.
Cette carte mère est dotée d’un connecteur pour ventilateur de processeur (Quiet Fan) à 4 broches. Si vous envisagez de connecter un ventilateur de processeur à 3 broches, veuillez le brancher sur la Broche 1-3.
Connecteur pour ventilateur de processeur / pompe à eau (CPU_FAN2/WP à 4 broches) (voir p.1, No. 4)
Connecteur d’alimentation ATX (ATXPWR1 à 24 broches) (voir p.1, No. 7)
N_SPEED_CONTROL
CPU_FAN_SPEED
FAN_VOLTAGE
12
1
Cette carte mère est dotée d’un
4
connecteur pour ventilateur de
3
2
processeur à refroidissement par
1
GND
eau à 4 broches. Si vous envis­agez de connecter un ventilateur de refroidisseur d'eau pour processeur à 3 broches, veuillez le brancher sur la Broche 1-3.
24
Cette carte mère est dotée d’un connecteur d’alimenta­tion ATX à 24 broches. Pour
Français
utiliser une alimentation ATX à 20 broches, veuillez eectuer
13
les branchements sur la Bro­che 1 et la Broche 13.
61
Page 64
Connecteur d’alimentation
4 1
8 5
1
1
SMB _DA TA_ MAI N
#
ATX 12V (ATX12V1 à 8 broches) (voir p.1, No. 1)
Cette carte mère est dotée d’un connecteur d’alimentation ATX 12V à 8 broches. Pour utiliser une alimentation ATX à 4 broches, veuillez eectuer les branchements sur la Broche 1 et la Broche 5.
Français
Connecteur d’alimentation ATX 12V (ATX12V2 à 4 broches) (voir p.1, No. 2)
Connecteurs underbolt AIC (TB1 à 5 broches) (voir p.1, No. 24)
Embase pour port série (COM1 à 9 broches) (voir p.1, No. 21)
Embase TPM (TPMS1 à 17 broches) (voir p.1, No. 22)
Veuillez connecter une source d'alimentation ATX 12 V à ce connecteur. *La che d'alimen­tation électrique s'adapte à ce connecteur dans un seul sens.
Veuillez connecter une carte d’extension (AIC) underbolt™ au connecteur AIC underbolt via le câble GPIO. *Veuillez installer la carte AIC underbolt™ sur la fente PCIE6 (fente par défaut).
RRXD1
DDTR#1
TTXD1
DDCD#1
DDSR#1
CCTS#1
RRTS#1
GND
RRI#1
Cette embase COM1 prend en charge un module de port série.
Ce connecteur prend en charge un
GN D
LAD 0
LAD 3
+3 V
+3V S B
D
GN
SER IRQ #
S_P WRD WN #
PC IRS T
GN D
LAD 1
LAD 2
module TPM (Trusted Platform
PC ICL K
FRA M E
Module – Module de plateforme
1
sécurisée), qui permet de sauve-
GN D
garder clés, certicats numériques, mots de passe et données en toute sécurité. Le système TPM permet
SMB _CL K_M AIN
également de renforcer la sécurité du réseau, de protéger les identités numériques et de préserver l’in­tégrité de la plateforme.
62
Page 65
Z390 Extreme4
1
D
1
Button
OCLED -
Embase LED RVB (RGB_LED1 à 4 broches) (voir p.1, No. 26) (RGB_LED2 à 4 broches) (voir p.1, No. 25)
Embase LED adressable (LED_DDR_A à 3 broches1) (voir p.1, No. 27)
12V GRB
DO_ADDR
VOUT
L'embase RVB sert à connecter le câble d'extension LED RVB qui permet aux utilisateurs de choisir parmi plusieurs eets lumineux LED.
Attention : N'installez jamais le
câble LED RVB dans le mauvais
sens ; dans le cas contraire, le
câble peut être endommagé.
*Veuillez consulter la page 33 pour des instructions supplémentaires sur cette embase.
Cette embase sert à connecter le
GN
câble d'extension LED adressa­ble qui permet aux utilisateurs de choisir parmi plusieurs eets lumineux LED.
Attention : N’installez jamais
le câble LED adressable dans
le mauvais sens. Dans le cas
contraire, le câble peut être
endommagé.
*Veuillez consulter la page 34 pour des instructions supplémentaires sur cette embase.
Embase mode Perfor­mances / OC facile (PM_OC à 4 broches) (voir p.1, No. 15)
1
Button-
+
OCLED+
Veuillez connecter le commu­tateur OC et l’indicateur LED OC du châssis sur cette embase conformément aux aectations des broches. Repérez les broches positive et négative avant de brancher les câbles.
Français
63
Page 66
1 Introduzione
Congratulazioni per l’acquisto della scheda madre ASRock Z390 Extreme4, una scheda madre adabile prodotta secondo i severissimi controlli di qualità ASRock. La scheda madre ore eccellenti prestazioni con un design robusto che si adatta all'impegno di ASRock di orire sempre qualità e durata.
Dato che le speciche della scheda madre e del soware BIOS possono essere aggiornate, il contenuto di questa documentazione sarà soggetto a variazioni senza preavviso. Nel caso di eventuali modi­che della presente documentazione, la versione aggiornata sarà disponibile sul sito Web di ASRock senza ulteriore preavviso. Per il supporto tecnico correlato a questa scheda madre, visitare il nostro sito Web per informazioni speciche relative al modello attualmente in uso. È possibile trovare l'elenco di schede VGA più recenti e di supporto di CPU anche sul sito Web di ASRock. Sito Web di ASRock http://www.asrock.com.
1.1 Contenuto della confezione
Scheda madre ASRock Z390 Extreme4 (Form Factor ATX)
•
Guida all'installazione rapida di ASRock Z390 Extreme4
•
CD di supporto ASRock Z390 Extreme4
•
1 x mascherina metallica posteriore I/O
•
4 x cavi dati Serial ATA (SATA) (opzionali)
•
1 x scheda ASRock SLI_HB_Bridge_2S (opzionali)
•
3 x viti per Socket M.2 (opzionali)
•
Italiano
64
Page 67
1.2 Speciche
Piattaforma
CPU
Chipset
Memoria
Z390 Extreme4
Fattore di forma ATX
•
Supporta processori 8th Gen e 9th Generation Intel® CoreTM
•
(Socket 1151) Digi Power design
•
Potenza a 12 fasi
•
Supporta la tecnologia Intel® Turbo Boost 2.0
•
Supporto di CPU unlocked Intel® K-Series
•
Supporta gamma completa overclocking BCLK ASRock
•
Intel® Z390
•
Tecnologia memoria DDR4 Dual Channel
•
4 x alloggi DIMM DDR4
•
Supporto di memoria DDR4 4300+(OC)*/4266(OC)/4133(O
•
C)/4000(OC)/3866(OC)/3800(OC)/3733(OC)/3600(OC)/32 00(OC)/2933(OC)/2800(OC)/2666/2400/2133 non-ECC, un-
buered * Per maggiori informazioni fare riferimento all'elenco dei supporti di memoria sul sito di ASRock. (http://www.asrock.com/)
Supporta moduli di memoria ECC UDIMM (funziona in
•
modalità non ECC)
Capacità max. della memoria di sistema: 64GB
•
Supporto di XMP (Extreme Memory Prole) Intel® 2.0
•
Contatti d’oro 15μ negli alloggi DIMM
•
Alloggio d’es­pansione
3 x Alloggi PCI Express 3.0 x16 (PCIE2/PCIE4/PCIE6:singolo
•
a x16 (PCIE2); doppio a x8 (PCIE2) / x8 (PCIE4); triplo a x8
(PCIE2) / x8 (PCIE4) / x4 (PCIE6))* * Supporto di SSD NVMe come disco d’avvio
3 x alloggi PCI Express 3.0 x1 (Flexible PCIe)
•
Supporto di AMD Quad CrossFireXTM, 3-Way CrossFireXTM
•
and CrossFireXTM
Supporta NVIDIA® Quad SLITMe SLI
•
1 x Socket M.2 (Key E), supporta moduli di tipo 2230 WiFi/BT
•
e Intel® CNVi (Integrated WiFi/BT)
Contatti d’oro 15μ nell’alloggio VGA PCIe (PCIE2)
•
TM
Italiano
65
Page 68
Graca
La videograca integrata della scheda video UHD Intel® e le
•
uscite VGA possono essere supportate soltanto con processori con GPU integrata. Supporta la videograca integrata della scheda video UHD
•
Intel®: Intel® Quick Sync Video con AVC, MVC (S3D) e MPEG-2 Full HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® UHD Graphics DirectX 12
•
Codica/decodica HWA: AVC/H.264, HEVC/H.265 8-bit,
•
HEVC/H.265 10-bit, VP8, VP9 8-bit, VP9 10-bit (solo decodica), MPEG2, MJPEG, VC-1 (solo decodica) Tre opzioni di output graco: D-Sub, HDMI e DisplayPort 1.2
•
Supporto di tre monitor
•
Supporta HDMI con risoluzione massima no a
•
4K x 2K (4096 x 2160) a 30Hz Supporta DisplayPort 1.2 con risoluzione massima no a
•
4K x 2K (4096x2304) a 60 Hz Supporta D-Sub con una risoluzione max. no a 1920 x 1200
•
a 60 Hz Supporto delle funzioni Auto Lip Sync, Deep Color (12bpc),
•
xvYCC e HBR (High Bit Rate Audio) con porta HDMI (è necessario un monitor compatibile HDMI) Supporto HDCP con le porte HDMI e DisplayPort 1.2
•
Supporto riproduzione 4K Ultra HD (UHD) sulle porte HDMI
•
e DisplayPort 1.2
Italiano
66
Audio
Audio HD a 7.1 canali con Content Protection (codec audio
•
Realtek ALC1220) Supporto audio Blu-ray Premium
•
Supporta protezione da sovratensione
•
Supporto di Purity SoundTM 4
•
- Cappucci audio Nichicon serie Fine Gold
- 120dB SNR DAC con amplicatore dierenziale
- NE5532 Premium Headset Amplier per connettore audio pannello frontale (supporta cue no a 600 Ohm)
- Ingresso Pure Power
Page 69
LAN
I/O pannello posteriore
- Tecnologia Direct Drive
- Schermatura isolata PCB
- Sensore impedenza sulla porta di uscita anteriore
- Layer PCB individuali per canali audio R/L
- LED RGB
- Connettore audio dorato 15 μ Supporta DTS Connect
•
LAN Gigabit 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Supporto WOL (Wake-On-LAN)
•
Supporta protezione da fulmini/scariche elettrostatiche
•
Supporto Energy Ecient Ethernet 802.3az
•
Supporto PXE
•
2 x porte antenna
•
1 x porta mouse/tastiera PS/2
•
1 x porta D-Sub
•
1 x porta HDMI
•
1 x DisplayPort 1.2
•
1 x porta uscita SPDIF ottico
•
1 x Porta USB 3.1 Gen2 di tipo A (10 Gb/s) (ReDriver)
•
(Supporto protezione ESD) 1 x Porta USB 3.1 Gen2 di tipo C (10 Gb/s) (ReDriver)
•
(Supporto protezione ESD) 4 x porte USB 3.1 Gen1 (Intel® Z390) (supporto protezione da
•
scariche elettrostatiche) 1 x porta LAN RJ-45 con LED (ACT/LINK LED e SPEED
•
LED) Connettori audio HD: altoparlante posteriore/centrale/basso/
•
ingresso linea/altoparlante anteriore/microfono
Z390 Extreme4
Italiano
Archiviazione
6 x connettori SATA3 6,0 Gb/s, supportano RAID (RAID 0,
•
RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology
16), NCQ, AHCI e Hot Plug* 2 x Connettori SATA3 6,0 Gb/s ASMedia ASM1061, sup-
•
portano NCQ, AHCI e Hot Plug
67
Page 70
Italiano
Connettore
* M2_1, SATA3_0 e SATA3_1 condividono le corsie. Se uno di essi è utilizzato, gli altri saranno disabilitati. * M2_2, SATA3_4 e SATA3_5 condividono le corsie. Se uno di essi è utilizzato, gli altri saranno disabilitati.
1 x socket Ultra M.2 (M2_1), supporta il modulo M.2 SATA3
•
6,0 Gb/s di tipo M Key 2230/2242/2260/2280 ed il modulo M.2 PCI Express no a Gen3 x4 (32 Gb/s)** 1 x socket Ultra M.2 (M2_2), supporta il modulo M.2 SATA3
•
6,0 Gb/s di tipo 2230/2242/2260/2280/22110 ed il modulo M.2
PCI Express no a Gen3 x4 (32 Gb/s)** ** Supporto di Intel® OptaneTM Technology ** Supporto di SSD NVMe come disco d’avvio ** Supporta kit ASRock U.2
1 x connettore porta COM
•
1 x connettore TPM
•
1 x connettore LED alimentazione e altoparlante
•
2 x collettore LED RGB
•
* Supporto totale di no a 12V/3A, 36W strip LED
1 x Header LED indirizzabile
•
* Supporto totale di no a 5V/3A, 15W strip LED
1 x connettore ventola CPU (4-pin)
•
* Il connettore ventola CPU supporta ventole CPU con potenza massima di 1 A (12 W).
1 x connettore ventola CPU/ventola pompa dell’acqua (4 pin)
•
(Controllo intelligente della velocità della ventola) * La ventola CPU/ventola pompa dell’acqua supporta ventole di sistemi di rareddamento ad acqua di potenza massima di 2A (24W).
3 x connettori ventola telaio/ventola pompa dell’acqua (4 pin)
•
(Controllo intelligente della velocità della ventola) * La ventola Chassis/ventola pompa dell’acqua supporta ventole di sistemi di rareddamento ad acqua di potenza massima di 2A (24W). * CPU_FAN2/WP, CHA_FAN1/WP, CHA_FAN2/WP e CHA_FAN3/WP sono in grado di rilevare se è in uso una ventola a 3 pin o 4 a pin.
1 x connettore alimentazione ATX 24-pin (connettore alimen-
•
tazione ad alta densità)
1 x connettore alimentazione 12V 8-pin (connettore alimen-
•
tazione ad alta densità)
68
Page 71
Funzionalità BIOS
1 x connettore alimentazione 12V 4-pin (connettore alimen-
•
tazione ad alta densità)
1 x connettore audio pannello frontale (15μ connettore audio
•
dorati)
1 x Connettore underbolt AIC (5-pin)
•
2 x connettori USB 2.0 (supporto di 4 porte USB 2.0) (Intel®
•
Z390) (supporta protezione da scariche elettrostatiche)
2 x connettore USB 3.1 Gen1 (supporto di 4 porte USB 3.1
•
Gen1) (hub ASMedia ASM1074) (supporto protezione da
scariche elettrostatiche)
1 x porta USB 3.1 tipo C connettore Gen1 (Intel® Z390) (Sup-
•
porto protezione ESD) sul pannello frontale
1 Basetta Modalità prestazioni / Overclocking (OC) facile
•
BIOS legale 2 x AMI UEFI con supporto GUI multilingue
•
(1 x Main BIOS e 1 x Backup BIOS)
Supporto della tecnologia Secure Backup UEFI
•
Eventi di riattivazione conformi a ACPI 6.0
•
Supporto di SMBIOS 2.7
•
CPU Core/Cache, GT, DRAM, PCH 1,0V, VCCIO, VCCST,
•
VCCSA, VCCPLL, CPU Internal PLL, GT PLL, Ring PLL,
agente di sistema PLL, controller memoria PLL, regolazione
multipla della tensione
Z390 Extreme4
Hardware Monitor
SO
Certicazioni
Sensore di temperatura: Ventole CPU, CPU/pompa dell'acqua,
•
telaio/pompa dell'acqua
Tachimetro ventola: Ventole CPU, CPU/pompa dell'acqua,
•
telaio/pompa dell'acqua
Ventola silenziosa (regolazione automatica velocità in base alla
•
temperatura della CPU): Ventole CPU, CPU/pompa dell'acqua,
telaio/pompa dell'acqua
Controllo velocità ventola: Ventole CPU, CPU/pompa dell'ac-
•
qua, telaio/pompa dell'acqua
Monitoraggio tensione: +12V, +5V, +3,3V, CPU Vcore, DRAM,
•
VPPM, PCH 1,0V, VCCSA, VCCST, VCCIO
Microso® Windows® 10 64 bit
•
FCC, CE
•
ErP/EuP Ready (è necessaria alimentazione ErP/EuP ready)
•
Italiano
69
Page 72
* Per informazioni dettagliate sul prodotto, visitare il nostro sito Web: http://www.asrock.com
Prestare attenzione al potenziale rischio previsto nella pratica di overclocking, inclusa la regolazione delle impostazioni nel BIOS, l'applicazione di tecnologia di Untied Overclocking o l'utilizzo di stru­menti di overclocking di terze parti. L'overclocking può inuenzare la stabilità del sistema o perno provocare danni ai componenti e ai dispositivi del sistema. Occorre eseguirlo a proprio rischio e spese. Non ci riterremo responsabili per possibili danni provocati da overclocking.
Italiano
70
Page 73
Z390 Extreme4
1.3 Impostazione jumper
L'illustrazione mostra in che modo vengono impostati i jumper. Quando il cappuccio del jumper è posizionato sui pin, il jumper è "cortocircuitato". Se sui pin non è posizionato alcun cappuccio del jumper, il jumper è "aperto".
Jumper per azzerare la CMOS (CLRCMOS1) (vedere pag. 1, n. 29)
CLRCMOS1 consente di azzerare i dati presenti nella CMOS. I dati presenti nella CMOS includono informazioni relative all'impostazione del sistema quali password del sistema, data, ora e parametri di impostazione del sistema. Per azzerare e reimpostare i parametri del sistema alla congurazione predenita, spegnere il computer e scollegare il cavo di alimentazione, quindi utilizzare un cappuccio del jumper per cortocircuitare i pin su CLRCMOS1 per 3 secondi. Ricordarsi di rimuovere il cappuccio del jumper dopo aver azzerato la CMOS. Se è necessario azzerare la CMOS dopo l'aggiornamento del BIOS, è necessario riavviare prima il sistema e in seguito spegnerlo prima di eseguire l'operazione di azzeramento della CMOS.
Jumper a 2 pin
Cortocircuitato: Azzerare la CMOS Aperto: Predenito
Italiano
71
Page 74
1.4 Header e connettori su scheda
1
Gli header e i connettori sulla scheda NON sono jumper. NON posizionare cappucci del jumper su questi header e connettori. Il posizionamento di cappucci del jumper su header e connettori provocherà danni permanenti alla scheda madre.
Italiano
Header sul pannello del sistema (PANEL1 a 9 pin) (vedere pag. 1, n. 17)
PWRBTN (tasto d’alimentazione):
Collegare al tasto d’alimentazione del pannello frontale del telaio. Utilizzando il tasto d’alimentazione è possibile congurare il modo in cui si spegne il sistema.
RESET (tasto di ripristino):
Collegare all'interruttore di ripristino del pannello frontale del telaio. Premere il tasto di ripristino per riavviare il sistema se il computer si blocca e non riesce ad eseguire un normale riavvio.
PLED (LED alimentazione del sistema):
collegare all'indicatore di stato dell'alimentazione sul pannello anteriore dello chassis. Il LED è acceso quando il sistema è in funzione. Il LED continua a lampeggiare quando il sistema si trova nello stato di sospensione S1/S3. Il LED è spento quando il sistema si trova nello stato di sospensione S4 o quando è spento (S5).
HDLED (LED di attività disco rigido):
collegare al LED di attività disco rigido sul pannello anteriore dello chassis. Il LED è acceso quando il disco rigido sta leggendo o scrivendo dati.
Il design del pannello anteriore può cambiare a seconda dello chassis. Un modulo del pannello fron­tale consiste principalmente di tasto d’alimentazione, tasto di ripristino, LED d’alimentazione, LED attività del disco rigido, altoparlanti e così via. Quando si collega il modulo del pannello frontale del telaio a questa basetta, assicurarsi che l’assegnazione dei cavi e l’assegnazione dei pin siano corrette.
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Collegare il tasto d'alimentazione, il tasto di ripristino e l'indicatore di stato del sistema del telaio a questa basetta in base all'assegnazione dei pin denita di seguito. Annotare i pin positivi e negativi prima di collegare i cavi.
72
Page 75
Z390 Extreme4
1
+5V
DUMMY
PLED+
PLED+
PLED-
DUMMY
SPEAKER
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
Connettore LED alimentazione e altoparlante (SPK_PLED1 a 7 pin) (vedere pag. 1, n. 18)
Connettori Serial ATA3 (SATA3_4_5: vedere pag. 1, n. 11) (SATA3_2_3: vedere pag. 1, n. 12) (SATA3_0_1: vedere pag. 1, n. 13) (SATA3_A1_A2: vedere pag. 1, n. 14)
SATA3_2SATA3_0
SATA3_A1 SATA3_4
Collegare i LED alimentazione e l’altoparlante a questo connettore.
Questi otto connettori SATA3 supportano cavi di trasmissione dati SATA per i dispositivi d’archiviazione interni velocità di trasferimento dati no a 6,0 Gb/s.
SATA3_3SATA3_1
* M2_1, SATA3_0 e SATA3_1 condividono le corsie. Se uno di essi è utilizzato, gli altri saranno disabilitati. * M2_2, SATA3_4 e SATA3_5 condividono le corsie. Se uno di essi è utilizzato, gli altri saranno disabilitati.
SATA3_A2 SATA3_5
* Per ridurre al minimo il tempo d’avvio, utilizzare le porte SATA Intel ® Z390 (SATA3_0) per i dispositivi SDD.
Header USB 2.0 (USB_1_2 a 9 pin) (vedere pag. 1, n. 20) (USB_3_4 a 9 pin) (vedere pag. 1, n. 19)
Ci sono due connettori su questa scheda madre. Ciascun header USB 2.0 può supportare due porte.
Italiano
73
Page 76
1
Header USB 3.1 Gen1
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
(USB3_5_6 a 19 pin) (vedere pag. 1, n. 8) (USB3_7_8 a 19 pin) (vedere pag. 1, n. 9)
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
IntA_PB_SSTX+
GND
IntA_PB_D-
IntA_PB_D+
Dummy
Ci sono due connettori su questa scheda madre. Ciascun header USB 3.1 Gen1 può supportare due porte.
Italiano
Connettore USB 3.1 Gen1 tipo C pannello anteriore (USB31_TC_2 a 26 pin) (vedere pag. 1, n. 10)
È presente un connettore USB
3.1 Gen1 tipo C pannello anteriore su questa scheda madre. Questo connettore viene utilizzato per il collegamento di un modulo USB 3.1 Gen1 per porte USB 3.1 Gen1 supplementari.
Header audio pannello anteriore (HD_AUDIO1 a 9 pin)
Questo header serve a collegare i dispositivi audio al pannello audio anteriore.
(vedere pag. 1, n. 28)
1. L'audio ad alta denizione supporta le funzioni Jack sensing, ma il lo del pannello sullo chassis deve supportare HDA per funzionare correttamente. Seguire le istruzioni presenti nel nostro manuale e nel manuale dello chassis per installare il sistema.
2. Se si utilizza un pannello audio AC’97, installarlo sull'header audio del pannello anteriore seguendo le fasi di seguito: A. Collegare Mic_IN (MIC) a MIC2_L. B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) a OUT2_L. C. Collegare Ground (GND) a Ground (GND). D. MIC_RET e OUT_RET servono soltanto per il pannello audio HD. Non è necessario collegarli per il pannello audio AC’97. E. Per attivare il microfono anteriore, andare alla scheda “FrontMic” nel pannello di controllo Realtek e regolare il “Volume di registrazione”.
74
Page 77
Z390 Extreme4
GN
OL
FA
FAN_SPEED_CONTROL
1 2 3 4
GND
OL
GND
OL
Connettori ventola chassis / pompa dell'acqua (CHA_FAN1/WP a 4 pin) (vedere pag. 1, n. 30)
(CHA_FAN2/WP a 4 pin) (vedere pag. 1, n. 23)
(CHA_FAN3/WPa 4 pin) (vedere pag. 1, n. 16)
Connettore ventola CPU (CPU_FAN1 a 4 pin) (vedere pag. 1, n. 3)
Connettore ventola CPU / pompa dell'acqua (CPU_FAN2/WP a 4 pin) (vedere pag. 1, n. 4)
FAN_VOLTAGE
FAN_SPEED
FAN_SPEED_CONTR
1 2 3 4
FAN_VOLTAGE
FAN_SPEED
FAN_SPEED_CONTR
1 2 3 4
D
FAN_VOLTAGE
FAN_SPEED
FAN_SPEED_CONTR
1 2 3 4
CPU_FAN_SPEED
FAN_VOLTAGE
N_SPEED_CONTROL
CPU_FAN_SPEED
FAN_VOLTAGE
GND
GND
Questa scheda madre è dotata di tre connettori ventola a 4 pin per il rareddamento ad acqua del telaio
. Se si decide di collegare una
ventola
telaio
con rareddamento ad acqua a 3 pin, collegarla al pin 1-3.
Questa scheda madre è dotata di un connettore per la ventola della CPU (Ventola silenziosa) a 4 pin. Se si decide di collegare una ventola della CPU a 3 pin, collegarla al pin 1-3.
Questa scheda madre è dotata
4
di un connettore per la ventola
3
2
della CPU con rareddamento
1
ad acqua a 4 pin. Se si decide di collegare una ventola della CPU con rareddamento ad acqua a 3 pin, collegarla al pin 1-3.
Italiano
Connettore di alimentazione ATX (ATXPWR1 a 24 pin) (vedere pag. 1, n. 7)
12
24
Questa scheda madre è dotata di un connettore di alimen­tazione ATX a 24 pin. Per utilizzare un'alimentazione ATX a 20 pin, collegarla lungo
1
13
il pin 1 e il pin 13.
75
Page 78
Connettore di
4 1
8 5
1
1
SMB _DA TA_ MAI N
#
alimentazione ATX da 12 V (ATX12V1 a 8 pin) (vedere pag. 1, n. 1)
Questa scheda madre è dotata di un connettore di alimen­tazione ATX da 12 V a 8 pin. Per utilizzare un'alimentazione ATX a 4 pin, collegarla lungo il pin 1 e il pin 5.
Italiano
Connettore di alimentazione ATX da 12 V (ATX12V2 a 4 pin) (vedere pag. 1, n. 2)
Connettori underbolt AIC (TB1 5-pin) (vedere pag. 1, n. 24)
Header porta seriale (COM1 a 9 pin) (vedere pag. 1, n. 21)
Header TPM (TPMS1 a 17 pin) (vedere pag. 1, n. 22)
Collegare un alimentatore ATX a 12 V a questo connettore. *La spina di alimentazione può essere inserita in questo connet­tore con un solo orientamento.
Collegare una scheda aggiuntiva underbolt™ (AIC) al connettore underbolt AIC utilizzando il cavo GPIO. * Installare la scheda underbolt™ AIC nell’alloggio (predenito) PCIE6.
RRXD1
DDTR#1
TTXD1
DDCD#1
DDSR#1
CCTS#1
RRTS#1
GND
RRI#1
Questo header COM1 supporta un modulo di porta seriale.
Questo connettore supporta il
GN D
LAD 0
LAD 3
+3 V
+3V S B
D
GN
SER IRQ #
S_P WRD WN #
PC IRS T
GN D
LAD 1
LAD 2
sistema Trusted Platform Module
PC ICL K
FRA M E
(TPM), che può archiviare in
1
modo sicuro chiavi, certicati
GN D
digitali, password e dati. Un sistema TPM permette anche di potenziare la sicurezza della rete,
SMB _CL K_M AIN
di proteggere identità digitali e di garantire l'integrità della piatta­forma.
76
Page 79
Z390 Extreme4
1
1
Button
OCLED -
Collettore LED RGB (RGB_LED1 a 4 pin) (vedere pag. 1, n. 26) (RGB_LED2 a 4 pin) (vedere pag. 1, n. 25)
Header LED indirizzabile (ADDR_LED1 a 3 pin) (vedere pag. 1, n. 27)
12V GRB
DO_ADDR
VOUT
GND
Il collettore RGB viene utilizzato per collegare la prolunga LED RGB, che consente agli utenti di scegliere tra vari eetti di illumi­nazione a LED.
Attenzione: Non installare il cavo
LED RGB in senso errato; in
caso contrario, il cavo potrebbe
danneggiarsi.
* Fare riferimento a pagina 33 per ulteriori istruzioni su questa basetta.
Questo header serve a collegare il cavo di estensione del LED indi­rizzabile che consente di scegliere tra vari eetti luce LED.
Attenzione: Non installare mai
il cavo del LED indirizzabile
secondo un orientamento
errato, altrimento potrebbe
danneggiarsi.
* Fare riferimento a pagina 34 per ulteriori istruzioni su questa basetta.
Basetta Modalità prestazi­oni / Overclocking (OC) facile (PM_OC a 4 pin) (vedere pag. 1, n. 15)
1
Button-
+
OCLED+
Collegare l’interruttore OC e l’in­dicatore LED OC sul telaio a ques­ta basetta in base all’assegnazione dei pin. Annotare i pin positivi e negativi prima di collegare i cavi.
Italiano
77
Page 80
1 Introducción
Gracias por comprar la placa base ASRock Z390 Extreme4, una placa base able fabricada según el rigurosísimo control de calidad de ASRock. Ofrece un rendimiento excelente con un diseño resistente de acuerdo con el compromiso de calidad y resistencia de ASRock.
Ya que las especicaciones de la placa base y el soware de la BIOS podrán ser actualizados, el contenido que aparece en esta documentación estará sujeto a modicaciones sin previo aviso. Si esta documentación sufre alguna modicación, la versión actualizada estará disponible en el sitio web de ASRock sin previo aviso. Si necesita asistencia técnica relacionada con esta placa base, visite nuestro sitio web para obtener información especíca sobre el modelo que esté utilizando. Podrá encontrar las últimas tarjetas VGA, así como la lista de compatibilidad de la CPU, en el sitio web de ASRock. Sitio web de ASRock http://www.asrock.com.
1.1 Contenido del paquete
Placa base ASRock Z390 Extreme4 (Factor de forma ATX)
•
Guía de instalación rápida de ASRock Z390 Extreme4
•
CD de soporte de ASRock Z390 Extreme4
•
1 x escudo panel E/S
•
4 x Cables de datos Serie ATA (SATA) (Opcional)
•
1 tarjeta ASRock SLI_HB_Bridge_2S (Opcional)
•
3 x tornillos para socket M.2 (Opcional)
•
Español
78
Page 81
1.2 Especicaciones
Factor de forma ATX
Plataforma
CPU
Conjunto de chips
Memoria
•
Compatible con la 8a y 9a generación de procesadores Intel®
•
CoreTM (Socket 1151) Digi Power design
•
Diseño de 12 fases de alimentación
•
Admite la tecnología Intel® Turbo Boost 2.0
•
Compatible con CPU serie K desbloqueada de Intel®
•
Compatible con overclocking de rango completo BCLK de
•
ASRock
Intel® Z390
•
Tecnología de memoria DDR4 de doble canal
•
4 x ranuras DIMM DDR4
•
Admite memoria sin búfer DDR4 4300+(OC)*/4266(OC)/4133
•
(OC)/4000(OC)/3866(OC)/3800(OC)/3733(OC)/3600(OC)/
3200(OC)/2933(OC)/2800(OC)/2666/2400/2133 no ECC. * Para obtener más información, consulte la lista de memorias compatibles en el sitio web de ASRock. (http://www.asrock.com/)
Admite módulos de memoria UDIMM ECC (funcionamiento
•
en modo no ECC)
Capacidad máxima de memoria del sistema: 64GB
•
Admite Perl de memoria extremo de Intel® (XMP) 2.0
•
Contacto 15μ Gold en ranuras DIMM
•
Z390 Extreme4
Ranura de expansión
3 x ranuras PCI Express 3.0 x16 (PCIE2/PCIE4/PCIE6:una
•
a x16 (PCIE2); doble a x8 (PCIE2) / x8 (PCIE4); triple a x8
(PCIE2) / x8 (PCIE4) / x4 (PCIE6))* * Admite unidad de estado sólido de NVMe como disco de arranque
3 x ranuras PCI Express 3.0 x1 (Flexible PCIe)
•
Compatible con AMD Quad CrossFireXTM, 3-Way
•
CrossFireXTM y CrossFireXTM
Compatible con NVIDIA® Quad SLITM y SLI
•
1 x M.2 Socket (Tecla E), es compatible con los módulos WiFi/
•
BT tipo 2230 e Intel® CNVi (WiFi/BT integrado)
Contacto 15μ Gold en ranura VGA PCIe (PCIE2)
•
TM
Español
79
Page 82
Español
Grácos
Intel® UHD Graphics Built-in Visuals y las salidas de VGA son
•
compatibles únicamente con procesadores con GPU integrado. Admite Intel® UHD Graphics Built-in Visuals: Intel® Quick
•
Sync Video con AVC, MVC (S3D) y MPEG-2 Full HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® UHD Graphics DirectX 12
•
Codicación y descodicación HWA: AVC/H.264, HEVC/
•
H.265 8 bits, HEVC/H.265 10 bits, VP8, VP9 8 bits, VP9 10 bits (solo descodicar), MPEG2, MJPEG, VC-1 (solo descodicar) Tres opciones de salida de grácos: D-Sub, HDMI y
•
DisplayPort 1.2 Compatible con tres monitores
•
Compatible con HDMI con una resolución máxima de
•
4K x 2K (4096x2160) a 30 Hz Compatible con DisplayPort 1.2 con una resolución máxima de
•
4K x 2K (4096x2304) a 60 Hz Admite D-Sub con una resolución máxima de 1920x1200
•
a 60 Hz Admite Sincronización automática entre audio y vídeo, color
•
profundo (12 bpc), xvYCC y HBR (audio de alta tasa de bits) con puerto HDMI (se necesita un monitor compatible con HDMI) Compatible con HDCP con puertos HDMI y
•
DisplayPort 1.2 Admite reproducción 4K Ultra HD (UHD) con los puertos
•
HDMI y DisplayPort 1.2
80
Audio
7.1 Audio CH HD con Protección de contenido
•
(Realtek ALC1220 Audio Codec) Compatible con audio Blu-ray Premium
•
Admite protección contra sobretensiones
•
Compatible con Purity SoundTM 4
•
- Tapas de audio Nichion de la serie Fine Gold
- 120dB SNR DAC con amplicador diferencial
- Amplicador de auriculares de alta calidad NE5532 para conector de audio en el panel frontal (admite auriculares de hasta 600 ohmios)
- Entrada de alimentación pura
Page 83
LAN
E/S en panel posterior
- Tecnología Direct Drive
- Protección de aislamiento PCB (circuito impreso)
- Detección de impedancia en el puerto de salida frontal
- Capas PCB individuales para canal de audio D/I
- LED RGB
- Conector de audio dorado de 15μ Compatible con DTS Connect
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Admite la función Reactivación de LAN
•
Admite protección contra rayos y descargas electrostáticas
•
(ESD) Admite Ethernet 802.3az de eciencia energética
•
Admite PXE
•
2 x Puertos de antena
•
1 x puerto de ratón/teclado PS/2
•
1 x puerto D-Sub
•
1 x puerto HDMI
•
1 x DisplayPort 1.2
•
1 puerto de salida SPDIF óptica
•
1 x Puerto USB 3.1 Gen2 Tipo-A (10 Gb/s) (ReDriver) (admite
•
protección ESD) 1 x Puerto USB 3.1 Gen2 Tipo-C (10 Gb/s) (ReDriver) (admite
•
protección ESD) 4 x Puertos USB 3.1 Gen1 (Intel® Z390) (admite protección
•
contra descargas electrostáticas) 1 x Puerto LAN RJ-45 con LED (LED DE ACTIVIDAD/
•
ENLACE y LED DE VELOCIDAD) Conector de audio HD: Altavoz trasero / Central / Graves /
•
Entrada de línea / Altavoz frontal / Micrófono
Z390 Extreme4
Español
Almacenami­ento
6 x Conectores SATA3 de 6,0 Gb/s, compatibilidad con RAID
•
(RAID 0, RAID 1, RAID 5, RAID 10, Intel Rapid Storage Tech­nology 16), NCQ, AHCI y conexión en caliente* 2 x Conectores SATA3 de 6,0 Gb/s de ASMedia ASM1061,
•
compatibilidad con las funciones NCQ, AHCI y "Conexión en caliente"
81
Page 84
Español
82
Conector
* M2_1, SATA3_0 y SATA3_1 comparten carriles. Si cualquiera de ellos está en uso, los otros se deshabilitan. * M2_2, SATA3_4 y SATA3_5 comparten carriles. Si cualquiera de ellos está en uso, los otros se deshabilitan.
1 x Zócalo Ultra M.2 (M2_1) que admite el módulo SATA3
•
6,0 Gb/s M.2 de tipo 2230/2242/2260/2280 con clave M y el módulo PCI Express M.2 hasta Gen3 x4 (32 Gb/s)** 1 x Zócalo Ultra M.2 (M2_2) que admite el módulo SATA3 6,0
•
Gb/s M.2 de tipo 2230/2242/2260/2280/22110 con clave M y el
módulo PCI Express M.2 hasta Gen3 x4 (32 Gb/s)** ** Compatible con la Tecnología OptaneTM de Intel® ** Admite unidad de estado sólido de NVMe como disco de arran­que ** Admite el kit U.2 de ASRock
1 x Base de conexiones de puerto COM
•
1 x Conector TPM
•
1 x LED de alimentación y base de conexiones para el altavoz
•
2 x Cabezales de indicador LED RGB
•
* Admite una tira de LED de hasta 12 V/3 A (36 W) en total
1 x Base de conexiones de LED direccionable
•
* Admite una tira de LED de hasta 5 V/3 A (15 W) en total
1 x Conector para ventilador de la CPU (4 contactos)
•
* El conector para ventilador de la CPU admite ventilador de la CPU con una potencia de ventilador de 1 A (12 W) máxima.
1 x Conector (4 contactos) para el ventilador de la bomba de
•
agua/CPU (control de velocidad de ventilador inteligente) * El ventilador de la CPU/bomba de agua admite ventilador del disipador por agua con una potencia de ventilador máxima de 2A (24 W).
3 x Conectores (4 contactos) para el ventilador de la bomba de
•
agua/chasis (control de velocidad de ventilador inteligente) * El ventilador de la bomba de agua/Chasis admite ventilador del disipador por agua con una potencia de ventilador máxima de 2A (24 W). * CPU_FAN2/WP, CHA_FAN1/WP, CHA_FAN2/WP y CHA_ FAN3/WP se pueden detectar automáticamente si se usa el venti­lador de 3 o 4 contactos.
1 x Conector de alimentación de 24 contactos y ATX (conector
•
de alimentación de alta densidad)
1 x Conector de alimentación de 8 contactos y 12V (conector
•
de alimentación de alta densidad)
Page 85
Función de la BIOS
Monitor de hardware
SO
Z390 Extreme4
1 x Conector de alimentación de 4 contactos y 12V (conector
•
de alimentación de alta densidad) 1 x Conector de audio en el panel frontal (15μ Conector de
•
audio de oro) 1 x conector underbolt AIC (5 contactos)
•
2 x Bases de conexiones USB 2.0 (admite 4 puertos USB 2.0)
•
(Intel® Z390). Admite protección contra descargas electrostáti­cas. 2 x Base de conexiones 3.1 Gen1 (admite 4 puertos USB 3.1
•
Gen1) (concentrador ASMedia ASM1074) (Admite protección contra descargas electrostáticas) 1 x Base de conexiones USB 3.1 Gen1 Tipo C en el panel frontal
•
(Intel® Z390) (admite protección ESD) 1 x Modo de rendimiento / Base de conexiones OC sencilla
•
2 x BIOS Legal UEFI AMI compatibles con interfaz gráca de
•
usuario multilingüe (1 BIOS Principal y 1 BIOS de copia de seguridad) Compatible con tecnología UEFI de copia de seguridad segura
•
Eventos de reactivación compatibles con ACPI 6.0
•
Admite SMBIOS 2.7
•
Multiajuste de voltaje de caché/núcleos de la CPU, GT, DRAM,
•
PCH 1,0V, VCCIO, VCCST, VCCSA, VCCPLL, PLL interna de la CPU, PLL GT, PLL de anillo, PLL de agente del sistema y PLL del controlador de memoria
Detección de temperatura: Ventiladores de la bomba de agua/
•
chasis, bomba de agua/CPU, CPU Tacómetro del ventilador: Ventiladores de la bomba de agua/
•
chasis, bomba de agua/CPU, CPU Ventilador silencioso (ajuste automático de la velocidad del
•
ventilador del chasis por temperatura de la CPU): Ventiladores de la bomba de agua/chasis, bomba de agua/CPU, CPU Control de varias velocidades del ventilador: Ventiladores de la
•
bomba de agua/chasis, bomba de agua/CPU, CPU Supervisión del voltaje: +12V, +5V, +3,3V, CPU Vcore, DRAM,
•
VPPM, PCH 1,0V, VCCSA, VCCST, VCCIO
Microso® Windows® 10 64 bits
•
Español
Certica­ciones
FCC y CE
•
Preparado para ErP/EuP (se necesita una fuente de alimentac-
•
ión preparada para ErP/EuP)
83
Page 86
* Para obtener información detallada del producto, visite nuestro sitio Web: http://www.asrock.com
Tenga en cuenta que hay un cierto riesgo implícito en las operaciones de overclocking, incluido el ajuste de la BIOS, aplicando la tecnología de overclocking liberada o utilizando las herramientas de overclocking de otros fabricantes. El overclocking puede afectar a la estabilidad del sistema e, incluso, dañar los componentes y dispositivos del sistema. Esta operación se debe realizar bajo su propia responsabilidad y usted debe asumir los costos. No asumimos ninguna responsabilidad por los posibles daños causados por el overclocking.
Español
84
Page 87
Z390 Extreme4
1.3 Instalación de los puentes
La instalación muestra cómo deben instalarse los puentes. Cuando la tapa de puente se coloca en los contactos, el puente queda “Corto”. Si no coloca la tapa de puente en los contactos, el puente queda “Abierto”.
Puente de borrado de CMOS (CLRCMOS1) (consulte la pág. 1, nº 29)
CLRCMOS1 le permite borrar los datos del CMOS. Los datos del CMOS incluyen información de instalación del sistema como, por ejemplo, la contraseña, la fecha y la hora del sistema y los parámetros de instalación del sistema. Para borrar y restablecer los parámetros del sistema a los valores predeterminados de instalación, apague el ordenador y desenchufe el cable de alimentación. A continuación, utilice una tapa de puente para acortar los contactos del CLRCMOS1 durante 3 segundos. Acuérdese de retirar la tapa de puente después de borrar el CMOS. Si necesita borrar el CMOS cuando acabe de actualizar la BIOS, deberá arrancar el sistema primero y, a continuación, deberá apagarlo antes de que realice el borrado del CMOS.
Puente de 2 contactos
Corto: Borrado de CMOS Abierto: Predeterminado
Español
85
Page 88
1.4 Conectores y cabezales incorporados
1
Los cabezales y conectores incorporados NO son puentes. NO coloque tapas de puente sobre estos cabezales y conectores. Si coloca tapas de puente sobre los cabezales y conectores dañará de forma permanente la placa base.
Español
Cabezal del panel del sistema (PANEL1 de 9 contactos) (consulte la pág. 1, nº 17)
PWRBTN (botón de alimentación):
Conéctelo al botón de alimentación del panel frontal del chasis. Deberá congurar la forma en la que su sistema se apagará mediante el botón de alimentación.
RESET (botón de restablecimiento):
Conéctelo al botón de restablecimiento del panel frontal del chasis. Pulse el botón de restablecimiento para resetear el ordenador si éste está bloqueado y no se puede reiniciar de forma normal.
PLED (Indicador LED de la alimentación del sistema):
Conéctelo al indicador de estado de la alimentación del panel frontal del chasis. El indicador LED permanece encendido cuando el sistema está funcionando. El indicador LED parpadea cuando el sistema se encuentra en estado de suspensión S1/S3. El indicador LED se apaga cuando el sistema se encuentra en estado de suspensión S4 o está apagado (S5).
HDLED (Indicador LED de actividad en el disco duro):
Conéctelo al indicador LED de actividad en el disco duro del panel frontal del chasis. El indicador LED permanece encendido cuando el disco duro está leyendo o escribiendo datos.
El diseño del panel frontal puede ser diferente dependiendo del chasis. Un módulo de panel frontal consta principalmente de: botón de alimentación, botón de restablecimiento, indicador LED de ali­mentación, indicador LED de actividad en el disco duro, altavoz, etc. Cuando conecte su módulo del panel frontal del chasis a este cabezal, asegúrese de que las asignaciones de los cables y los contactos coinciden correctamente.
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Conecte el botón de alimentación, el botón de restablecimiento y el indicador de estado del sistema que se encuentran en el chasis a esta base de conexiones según las asignaciones de contactos que se indica a continuación. Cerciórese de cuáles son los contactos positivos y los negativos antes de conectar los cables.
86
Page 89
Z390 Extreme4
1
+5V
DUMMY
PLED+
PLED+
PLED-
DUMMY
SPEAKER
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
LED de alimentación y base de conexiones para la altavoz (SPK_PLED1 de 7 contactos) (consulte la pág. 1, nº 18)
Conectores Serie ATA3 (SATA3_4_5: consulte la pág.1, nº 11) (SATA3_2_3: consulte la pág.1, nº 12) (SATA3_0_1: consulte la pág.1, nº 13) (SATA3_A1_A2: consulte la pág.1, nº 14)
SATA3_2SATA3_0
SATA3_A1 SATA3_4
Conecte el LED de alimentación del chasis y el altavoz del chasis a esta base de conexiones.
Estos ocho conectores SATA3 son compatibles con cables de datos SATA para dispositivos de almacenamiento interno con una velocidad de transferencia de datos de hasta 6,0 Gb/s.
SATA3_3SATA3_1
* M2_1, SATA3_0 y SATA3_1 comparten carriles. Si cualquiera de ellos está en uso, los otros se deshabilitan. * M2_2, SATA3_4 y SATA3_5 comparten carriles. Si cualquiera de ellos está en uso, los otros se deshabilitan.
SATA3_A2 SATA3_5
*Para minimizar el tiempo de arranque, use los puertos SATA de Intel® Z390 (SATA3_0) para las unidades de estado sólido.
Cabezales USB 2.0 (USB_1_2 de 9 contactos) (consulte la pág. 1, nº 20) (USB_3_4 de 9 contactos) (consulte la pág. 1, nº 19)
Hay dos bases de conexiones
Español
en esta placa base. Cada cabezal USB 2.0 admite dos puertos.
87
Page 90
1
Cabezales USB 3.1 Gen1
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
(USB3_5_6 de 19 contactos) (consulte la pág. 1, nº 8) (USB3_7_8 de 19 contactos) (consulte la pág. 1, nº 9)
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
IntA_PB_SSTX+
GND
IntA_PB_D-
IntA_PB_D+
Dummy
Hay dos bases de conexiones en esta placa base. Cada cabezal USB 3.1 Gen1 admite dos puertos.
Español
Base de conexiones USB
3.1 Gen1 de tipo C en el panel frontal (USB31_TC_2 de 26 contactos) (consulte la pág. 1, nº 10)
Existe una base de conexiones USB 3.1 Gen1 de tipo C en el panel frontal en esta placa base. Esta base de conexiones se utiliza para conectar un módulo USB 3.1 Gen1 para puertos USB 3.1 Gen1 adicionales.
Cabezal de audio del panel frontal (HD_AUDIO1 de
Este cabezal se utiliza para conectar dispositivos de audio
al panel de audio frontal. 9 contactos) (consulte la pág. 1, nº 28)
1. El Audio de Alta Denición (HDA, en inglés) es compatible con el método de sensor de conectores, sin embargo, el cable del panel del chasis deberá ser compatible con HDA para que pueda funcionar correctamente. Siga las instrucciones que se indican en nuestro manual y en el manual del chasis para instalar su sistema.
2. Si utiliza un panel de audio AC’97, colóquelo en el cabezal de audio del panel frontal siguien­do los pasos que se describen a continuación: A. Conecte Mic_IN (MIC) a MIC2_L. B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) a OUT2_L. C. Conecte Ground (Conexión a tierra) (GND) a Ground (GND). D. MIC_RET y OUT_RET se utilizan únicamente con el panel de audio HD. No es necesario que los conecte en el panel de audio AC’97. E. Para activar el micrófono frontal, vaya a la cha “micrófono frontal” (Front Mic) en el panel de control de Realtek y ajuste el “Volumen de grabación” (Recording Volume).
88
Page 91
Z390 Extreme4
GN
OL
FA
FAN_SPEED_CONTROL
1 2 3 4
GND
OL
GND
OL
Conectores del ventilador de la bomba de agua/cha­sis (CHA_FAN1/WP de 4 contactos) (consulte la pág. 1, nº 30)
(CHA_FAN2/WP de 4 contactos) (consulte la pág. 1, nº 23)
(CHA_FAN3/WP de 4 contactos) (consulte la pág. 1, nº 16)
Conector del ventilador de la CPU (CPU_FAN1 de 4 contactos) (consulte la pág. 1, nº 3)
FAN_VOLTAGE
FAN_SPEED
1 2 3 4
FAN_VOLTAGE
FAN_SPEED
1 2 3 4
D
FAN_VOLTAGE
FAN_SPEED
1 2 3 4
CPU_FAN_SPEED
FAN_VOLTAGE
FAN_SPEED_CONTR
FAN_SPEED_CONTR
FAN_SPEED_CONTR
GND
Esta placa base proporciona tres conectores para el ventilador del chasis
para refrigeración por agua de 4 contactos. Si tiene pensando conectar un ventilador de refrig­eración por agua del
chasis
de 3 contactos, conéctelo al contacto 1-3.
Esta placa base contiene un conector de ventilador (venti­lador silencioso) de CPU de 4 contactos. Si tiene pensando conectar un ventilador de CPU de 3 contactos, conéctelo al contacto 1-3.
Conector del ventilador de la bomba de agua/CPU (CPU_FAN2/WP de 4 contactos) (consulte la pág. 1, nº 4)
Conector de alimentación ATX (ATXPWR1 de 24 contactos) (consulte la pág. 1, nº 7)
N_SPEED_CONTROL
CPU_FAN_SPEED
FAN_VOLTAGE
12
1
Esta placa base proporciona un
4
3
conector de ventilador de CPU de
2
1
GND
refrigeración por agua de 4 con­tactos. Si tiene pensando conectar un ventilador de disipador por
Español
agua de CPU de 3 contactos, conéctelo al contacto 1-3.
24
Esta placa base contiene un conector de alimentación ATX de 24 contactos. Para utilizar una toma de alimentación
13
ATX de 20 contactos, conécte­la en los contactos del 1 al 13.
89
Page 92
Conector de alimentación
4 1
8 5
1
1
SMB _DA TA_ MAI N
#
ATX de 12V (ATX12V1 de 8 contactos) (consulte la pág. 1, nº 1)
Esta placa base contiene un conector de alimentación ATX de 12V y 8 contactos. Para uti­lizar una toma de alimentación ATX de 4 contactos, conéctela en los contactos del 1 al 5.
Español
Conector de alimentación ATX de 12V (ATX12V2 de 4 contactos) (consulte la pág. 1, nº 2)
Conectores underbolt AIC (TB1 de 5 contactos) (consulte la pág. 1, nº 24)
Cabezal de puerto serie (COM1 de 9 contactos) (consulte la pág. 1, nº 21)
Cabezal TPM (TPMS1 de 17 contactos) (consulte la pág. 1, nº 22)
Conecte una fuente de alimentación ATX 12V en este conector. *El enchufe de la fuente de alimentación encaja en este conector en una única dirección.
Enchufe una tarjeta complementaria (AIC) underbolt™ al conector underbolt AIC a través del cable GPIO. *Instale la tarjeta underbolt™ AIC a PCIE6 (ranura predeterminada).
RRXD1
DDTR#1
TTXD1
DDCD#1
DDSR#1
CCTS#1
RRTS#1
GND
RRI#1
Este cabezal COM1 admite un módulo de puerto serie.
Este conector es compatible con el
GN D
LAD 0
LAD 3
+3 V
+3V S B
D
GN
SER IRQ #
S_P WRD WN #
PC IRS T
GN D
LAD 1
LAD 2
sistema Módulo de Plataforma Se-
PC ICL K
FRA M E
gura (TPM, en inglés), que puede
1
almacenar de forma segura claves,
GN D
certicados digitales, contraseñas y datos. Un sistema TPM también ayuda a aumentar la seguridad
SMB _CL K_M AIN
en la red, protege las identidades digitales y garantiza la integridad de la plataforma.
90
Page 93
Z390 Extreme4
1
D
1
Button
OCLED -
Cabezales de LED RGB (RGB_LED1 de 4 contactos) (consulte la pág. 1, nº 26) (RGB_LED2 de 4 contactos) (consulte la pág. 1, nº 25)
Base de conexiones de LED direccionable (ADDR_LED1 de 3 con­tactos) (consulte la pág. 1, nº 27)
12V GRB
DO_ADDR
VOUT
El cabezal RGB se utiliza para conectar el alargador de LED RGB que permite a los usuarios elegir entre varios efectos de ilumi­nación de LED.
Precaución: Nunca instale
el cable de LED RGB con la
orientación incorrecta ya que,
de lo contrario, el cable puede
dañarse.
*Consulte la página 33 para ob­tener más instrucciones sobre esta base de conexiones.
La base de conexiones se usa para
GN
conectar el alargador de LED direccionable que permite a los usuarios elegir entre varios efectos de iluminación LED.
Precaución: Nunca instale el
cable de LED direccionable con
la orientación incorrecta ya que,
de lo contrario, el cable puede
dañarse.
*Consulte la página 34 para ob­tener más instrucciones sobre esta base de conexiones.
Modo de rendimiento / Base de conexiones OC sencilla (PM_OC de 4 contactos) (consulte la pág. 1, nº 15)
1
Button-
+
OCLED+
Español
Conecte el conmutador OC y el indicador LED OC del chasis a esta base de conexiónes conforme a las asignaciones de los contactos. Cerciórese de cuáles son los contactos positivos y los negativos antes de conectar los cables.
91
Page 94
Русский
1 Введение
Благодарим вас за приобретение надежной системной платы ASRock Z390 Extreme4, выпускаемой под постоянным жестким контролем качества компании ASRock. Эта материнская плата обеспечивает великолепную производительность и отличается надежной конструкцией в соответствии с требованиями компании ASRock в отношении качества и долговечности.
По причине обновления характеристик системной платы и программного обеспечения BIOS содержимое настоящей документации может быть изменено без предварительного уведомления. При изменении содержимого настоящего документа его обновленная версия будет доступна на веб-сайте ASRock без предварительного уведомления. При необходимости технической поддержки, связанной с материнской платой, посетите веб­сайт и найдите на нем информацию о модели используемой вами материнской платы. На веб-сайте ASRock также можно найти самый последний перечень поддерживаемых VGA­карт и ЦП. Веб-сайт ASRock http://www.asrock.com.
1.1 Комплект поставки
Материнская плата ASRock Z390 Extreme4 (форм-фактор ATX)
•
Краткое руководство по установке платы ASRock Z390 Extreme4
•
Компакт-диск с ПО для платы ASRock Z390 Extreme4
•
1 экран панели с портами ввода-вывода
•
4 кабеля передачи данных Serial ATA (SATA) (приобретаются отдельно)
•
1 карта ASRock SLI_HB_Bridge_2S (приобретаются отдельно)
•
3 винта для слота M.2 (приобретаются отдельно)
•
92
Page 95
1.2 Технические характеристики
Форм-фактор ATX
Платформа
ЦП
Чипсет
Память
•
Поддержка процессоров 8го и 9го поколения Intel® CoreTM
•
(Socket 1151) Digi Power design
•
Система питания 12
•
Поддерживается технология Intel® Turbo Boost 2.0
•
Поддержка процессоров Intel® серии K с
•
разблокированным множителем Поддержка полного разгона процессора ASRock BCLK
•
Intel® Z390
•
Двухканальная память DDR4
•
4 x гнезда DDR4 DIMM
•
Поддержка модулей памяти DDR4 4300+(OC)*/4266
•
(OC)/4133(OC)/4000(OC)/3866(OC)/3800(OC)/3733(OC)/ 3600(OC)/3200(OC)/2933(OC)/2800(OC)/2666/2400/2133 не
относящихся к ECC, небуферизованной памяти * Дополнительная информация представлена в Списке совместимой памяти (Memory Support List ) на веб-сайте ASRock. (http://www.asrock.com/)
Поддержка модулей памяти ECC UDIMM (работа в
•
режиме, отличном от ЕСС)
Максимальный объем ОЗУ: 64 Гб
•
Поддерживается Intel® Extreme Memory Prole (XMP) 2.0
•
Позолоченные (15мкм) контакты слотов DIMM
•
Z390 Extreme4
Русский
Слоты расширения
3 x PCI Express 3.0 x16 (PCIE2/PCIE4/PCIE6:один x16
•
(PCIE2); два x8 (PCIE2) / x8 (PCIE4); три x8 (PCIE2) / x8
(PCIE4) / x4 (PCIE6))* * Поддерживаются в качестве загрузочных SSD-диски типа NVMe.
3 x PCI Express 3.0 x1 разъем (Flexible PCIe)
•
Поддержка AMD Quad CrossFireXTM, 3-Way CrossFireXTM и
•
CrossFireXTM
Поддержка NVIDIA® Quad SLITM и SLI
•
1 слот M.2 (ключ E) для модуля WiFi/BT типа 2230 и Intel®
•
CNVi (встроенные WiFi/BT)
15μ Золоченые контакты разъема VGA PCIe (PCIE2)
•
TM
93
Page 96
Русский
Графическая подсистема
Встроенный видеоадаптер Intel® UHD Graphics и выходы
•
VGA поддерживаются только при использовании ЦП со встроенными графическими процессорами. Поддерживаемые встроенные технологии визуализации
•
Intel® UHD Graphics: Intel® Quick Sync Video с полностью аппаратным кодированием1 в форматах AVC, MVC (S3D) и MPEG-2, Intel® InTruTM 3D, технология Intel® Clear Video HD, Intel® InsiderTM, Intel® UHD Graphics DirectX 12
•
Программно-аппаратное кодирование-декодирование:
•
AVC/H.264, HEVC/H.265 8 бит, HEVC/H.265 10 бит, VP8, VP9 8 бит, VP9 10 бит (только декодирование), MPEG2, MJPEG, VC-1 (только декодирование) Три видеовыхода: D-Sub, HDMI и DisplayPort 1.2
•
Поддержка работы с тремя мониторами
•
Поддержка HDMI с максимальным разрешением до 4K x
•
2K (4096x2160) при 30 Гц Поддерживается DisplayPort 1.2 с максимальным
•
разрешением до 4K x 2K (4096x2304) при 60 Гц Поддерживается D-Sub с максимальным разрешением до
•
1920x1200 при 60 Гц Поддерживаются Auto Lip Sync, Deep Color (12 бит/цвет),
•
xvYCC и HBR (High Bit Rate Audio) через порт HDMI (требуется соответствующий HDMI-монитор) Поддерживается функция HDCP через порты HDMI и
•
DisplayPort 1.2 Поддержка вывода видео с разрешением 4K Ultra HD
•
(UHD) на порты HDMI и DisplayPort 1.2
94
Звук
7.1-канальный звук высокой четкости HD Audio с защитой
•
данных (аудиокодек Realtek ALC1220) Поддержка Premium Blu-ray Audio
•
Защита от перепадов напряжения в электрической сети
•
Поддержка Purity SoundTM 4
•
- Конденсаторы для аудиосистем серии Nichicon Fine Gold
- 120 дБ SNR DAC с дифференциальным усилителем
- Первоклассный усилитель NE5532 для гарнитуры у аудиоразъема на передней панели (поддерживаются гарнитуры с сопротивлением до 600Ом)
- Стабилизированный вход питания
Page 97
LAN
Порты ввода­вывода на задней панели
- Технология Direct Drive
- Изолирующее экранирование печатной платы
- Определение сопротивления нагрузки, подключенной к порту на передней панели
- Отдельные слои печатной платы для левого и правого аудиоканалов
- Светодиодная RGB-подсветка
- Позолоченный аудиоразъем (15мкм)
Поддержка DTS-подключения
•
Gigabit Ethernet 10/100/1000 Мбит/с
•
Giga PHY Intel® I219V
•
Поддерживается пробуждение по ЛВС
•
Молниезащита и защита от электростатических
•
разрядов Поддерживается Energy Ecient Ethernet 802.3az
•
Поддерживается PXE
•
2 антенных порта
•
1 порт PS/2 для мыши/клавиатуры
•
1 порт D-Sub
•
1 порт HDMI
•
1 порт DisplayPort 1.2
•
1 оптический выход SPDIF
•
1 порт USB 3.1 Gen2 тип A (10 Гбит/с) (ReDriver) (с
•
защитой от электростатических разрядов) 1 порт USB 3.1 Gen2 тип С (10 Гбит/с) (ReDriver) (с
•
защитой от электростатических разрядов) 4 портов USB 3.1 Gen1 (Intel® Z390) (с защитой от
•
электростатических разрядов) 1 порт ЛВС RJ-45 с индикаторами («Активность/
•
Соединение» и «Скорость») Разъемы HD Audio: задние динамики / центральный
•
динамик / сабвуфер / линейный вход / передние динамики / микрофон
Z390 Extreme4
Русский
Запоминающие устройства
6 разъемов SATA3 с пропускной способностью 6,0
•
Гб/с, поддержка RAID (RAID 0, RAID 1, RAID 5, RAID 10, технологии Intel Rapid Storage 16), NCQ, AHCI и «горячего» подключения* 2 порта SATA3 6,0Гбит/с ASMedia ASM1061, поддержка
•
функций NCQ, AHCI и «горячей» замены
95
Page 98
Русский
Разъемы
* Общие каналы M2_1, SATA3_0 и SATA3_1. Если используется один из них, остальные будут отключены. * Общие каналы M2_2, SATA3_4 и SATA3_5. Если используется один из них, остальные будут отключены.
1 слот Ultra M.2 (M2_1), поддерживается модуль
•
M.2 SATA3 типа 2230/2242/2260/2280 с ключом M с пропускной способностью 6,0Гб/с и модуль M.2 PCI Express до версии Gen3 x4 (32Гб/с)** 1 x слот Ultra M.2 (M2_2), поддерживает модуль M.2
•
SATA3 типа 2230/2242/2260/2280/22110 с пропускной способностью 6,0Гб/с и модуль M.2 PCI Express до
версии Gen3 x4 (32Гб/с) с ключом M.** ** Поддерживается технология Intel® OptaneTM ** Поддерживаются в качестве загрузочных SSD-диски типа NVMe ** Поддерживается комплект ASRock U.2
1 колодка СОМ-порта
•
1 колодка ТРМ
•
1 колодка светодиодного индикатора питания и
•
корпусного динамика
2 колодки для подключения светодиодной RGB-
•
подсветки * Поддерживается светодиодная лента (максимум 12В/3А, суммарной мощностью до 36Вт).
1 колодка адресуемой светодиодной подсветки
•
* Поддерживается светодиодная лента (максимум 5В/3А, суммарной мощностью до 15Вт).
1 разъем для вентилятора охлаждения ЦП,
•
4-контактный * Разъем процессорного вентилятора поддерживает вентилятор с потребляемым током не более 1А (12Вт).
1 разъем для вентилятора или водяной помпы
•
водяного охлаждения ЦП (4-контактный) (смарт-
регулятор скорости вентилятора) * Разъем для процессорного корпусного вентилятора или водяной помпы поддерживает вентилятор с потребляемым током не более 2А (24Вт)
3 разъемы для корпусного вентилятора или водяной
•
помпы (4-контактный) (смарт-регулятор скорости
вентилятора)
96
Page 99
Z390 Extreme4
* Разъем для процессорного корпусного вентилятора или водяной помпы поддерживает вентилятор с потребляемым током не более 2А (24Вт). * Для разъемов CPU_FAN2/WP, CHA_FAN1/WP, CHA_ FAN2/WP и CHA_FAN3/WP автоматически определяется тип подключенного вентилятора: 3- или 4-контактный.
1 24-контактных разъем питания ATX (Высокоплотный
•
разъем питания) 1 разъем питания 12 В (8-контактный разъем питания
•
высокой плотности) 1 разъем питания 12 В (4-контактный разъем питания
•
высокой плотности) 1 аудиоразъем для передней панели (позолоченные
•
контакты аудиоразъема, 15мкм) 1 AIC-разъем underbolt (5-контактный)
•
2 колодки USB 2.0 (4 портов USB 2.0) (Intel® Z390) (с
•
защитой от электростатических разрядов) 2 колодка USB 3.1 Gen1 (4 порта USB 3.1 Gen1)
•
(концентратор ASMedia ASM1074) (с защитой от электростатических разрядов) 1 колодка порта USB 3.1 Gen1 тип С на передней
•
панели (Intel® Z390) (с защитой от электростатических разрядов) 1 колодка для режима повышенной производительности
•
и легкого разгона
Параметры BIOS
2 чипа AMI UEFI Legal BIOS с поддержкой
•
многоязычного ГИП (1 основной BIOS и 1 резервный BIOS) Поддержка технологии безопасного резервного
•
копирования UEFI Поддержка функций пробуждения по стандарту ACPI
•
6.0 Поддержка SMBIOS 2.7
•
Регулировка напряжений: ядра/кэш ЦП, GT, DRAM,
•
PCH 1,0В, VCCIO, VCCST, VCCSA, VCCPLL, внутренний PLL ЦП, GT PLL, PLL кольцевой шины, PLL системного агента, PLL контроллера памяти
Русский
97
Page 100
Русский
Контроль оборудования
Операционные системы
Сертификация
Контроль температуры: Вентилятор ЦП; Вентилятор
•
или помпа водяного охлаждения ЦП; Вентилятор или помпа водяного охлаждения корпуса Тахометр: Вентилятор ЦП; Вентилятор или помпа
•
водяного охлаждения ЦП; Вентилятор или помпа водяного охлаждения корпуса Бесшумная работа (с автоматической регулировкой
•
скорости вращения в зависимости от температуры ЦП): Вентилятор ЦП; Вентилятор или помпа водяного охлаждения ЦП; Вентилятор или помпа водяного охлаждения корпуса Регулировка скорости вращения: Вентилятор ЦП;
•
Вентилятор или помпа водяного охлаждения ЦП; Вентилятор или помпа водяного охлаждения корпуса Контроль напряжений: +12В, +5В, +3,3В, напряжение
•
ядра ЦП, DRAM, VPPM, PCH 1,0B, VCCSA, VCCST, VCCIO
Microso® Windows® 10 (64-разрядная)
•
FCC, CE
•
Совместимость с ErP/EuP (необходим блок питания,
•
соответствующий стандарту ErP/EuP)
* С дополнительной информацией об изделии можно ознакомиться на веб-сайте: http://www.asrock.com
Следует учитывать, что разгон процессора, включая изменение настроек BIOS, применение технологии Untied Overclocking и использование инструментов разгона независимых производителей, сопряжен с определенным риском. Разгон процессора может снизить стабильность системы или даже привести к повреждению ее компонентов и устройств. Разгон процессора осуществляется пользователем на собственный риск и за собственный счет. Мы не несем ответственность за возможный ущерб, вызванный разгоном процессора.
98
Loading...