ASRock J4105-ITX Service Manual

Version 1.0

Published December 2017

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium batter y adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply)

e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Motherboard Layout 5

1.4 I/O Panel 7

Chapter 2 Installation 9

2.1 Installation of Memory Modules (SO-DIMM) 10

2.2 Expansion Slot (PCI Express Slot) 12

2.3 Jumpers Setup 13

2.4 Onboard Headers and Connectors 14

2.5 M.2 WiFi/BT Module Installation Guide 17

Chapter 3 Software and Utilities Operation 19

3.1 Installing Drivers 19

3.2 ASRock Live Update & APP Shop 20

3.2.1 UI Overview 20

3.2.2 Apps 21

3.2.3 BIOS & Drivers 24

3.2.4 Setting 25

Chapter 4 UEFI SETUP UTILITY 26

4.1 Introduction 26

4.1.1 UEFI Menu Bar 26

4.1.2 Navigation Keys 27

4.2 Main Screen 28

4.3 Advanced Screen 29

4.3.1 CPU Conguration 30

4.3.2 Chipset Conguration 31

4.3.3 Storage Conguration 33

4.3.4 Super IO Conguration 35

4.3.5 ACPI Conguration 36

4.3.6 USB Conguration 38

4.4 Tools 39

4.5 Hardware Health Event Monitoring Screen 41

4.6 Security Screen 42

4.7 Boot Screen 43

4.8 Exit Screen 45

Chapter 1 Introduction

ank you for purchasing ASRock J5005-ITX/J4105-ITX motherboard, a reliable

motherboard produced under ASRock ’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock ’s

commitment to quality and endurance.

In this manual, Chapter 1 and 2 contains the introduction of the motherboard

and step-by-step installation guides. Chapter 3 contains the operation guide of the

soware and utilities. Chapter 4 contains the conguration guide of the BIOS setup.

Becau se the motherboard specication s and the BIOS soware might be upd ated, the content of this documentation will be subject to change without notice. In case any modications of this documentation occur, the updated version w ill be available on ASRock’s website without further notice. If you require technical support related to this motherboard, plea se visit our webs ite for specic information about the model you are using. You may nd the latest VGA cards and CPU support li st on ASRock’s website a s well. ASRock website http://www.asrock.com.

1.1 Package Contents

ASRock J5005-ITX/J4105-ITX Motherboard (Mini-ITX Form Factor)

•

ASRock J5005-ITX/J4105-ITX Quick Installation Guide

•

ASRock J5005-ITX/J4105-ITX Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x I/O Panel Shield

•

1 x Screw for M.2 Socket (O pt ional)

•

J5005-ITX J4105-ITX

English

1.2 Specications

Platform

CPU

Memory

Expansion Slot

•

* 2GB DRAM per module is not supported.

•

Mini-ITX Form Factor Solid Capacitor design

Intel® Quad-Core Pentium® Silver Processor J5005 (up to 2.8 GHz) (for J5005-ITX) Intel® Quad-Core Processor J4105 (up to 2.5 GHz)

(for J4105-ITX)

Dual Channel DDR4 Memory Technology 2 x DDR4 SO-DIMM Slots

Supports DDR4 2400/2133 non-ECC, un-buered memory Max. capacity of system memor y: 8GB

1 x PCI Express 2.0 x1 Slot 1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module and Intel® CNVi (Integrated WiFi/BT)

English

Graphics

• Integrated Intel® UHD Graphics 605: 18 EUs inside (Up to 80 0M Hz) (for J5005-ITX)

• Integrated Intel® UHD Graphics 600: 12 EUs inside (Up to 750 MH z) (for J4105-ITX)

• DX12, OpenGL 4.3, OGL ES 3.0, OpenCL 2.0

• HW Acceleration Decode: HEVC (H.265) 8 bit, HEVC

(H.265)10 bit, H.264 @ Lvl5.2 (AVC), JPEG/MJPEG, VP8, VP9 8bit, VP9 10 bit

• HW Acceleration Encode: HEVC (H.265) 8 bit, HEVC (H.265)10 bit, H.264 @ Lvl5.2 (AVC), JPEG/MJPEG, VP8, VP9 8bit

• ree graphics output options: D-Sub, DVI-D and HDMI

• Supports Triple Monitor

• Supports HDMI with max. resolution up to 4K x 2K

(4096x2160) @ 60Hz

• Supports DVI-D with max. resolution up to 1920x1200 @ 60Hz

• Supports D-Sub with max. resolution up to 2048x1536 @ 60Hz

• Supports Auto Lip Sync, xvYCC and HBR (High Bit Rate Audio) with HDMI Port (Compliant HDMI monitor is required)

Audio

LAN

Rear Panel I/O

J5005-ITX J4105-ITX

• Supports HDCP with DVI-D and HDMI Ports

• Supports Full HD 1080p Blu-ray (BD) playback with DVI-D

and HDMI Ports

7.1 CH HD Audio with Content Protection (Realtek ALC892

•

Audio Codec) Premium Blu-ray Audio support

•

Supports Surge Protection

•

ELNA Audio Caps

•

PCIE x1 Gigabit LAN 10/100/1000 Mb/s

•

Realtek RTL8111H

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

1 x PS/2 Mouse Port

•

1 x PS/2 Keyboard Port

•

1 x D-Sub Port

•

1 x DVI-D Port

•

1 x HDMI Port

•

1 x Optical SPDIF Out Port

•

2 x USB 2.0 Ports (Supports ESD Protection)

•

2 x USB 3.1 Gen1 Ports (Supports ESD Protection)

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED) HD Audio Jacks: Rear Speaker / Central / Bass / Line in /

•

Front Speaker / Microphone

Storage

Connector

2 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and

•

Hot Plug 2 x SATA3 6.0 Gb/s Connectors by ASMedia ASM1061,

•

support NCQ, AHCI and Hot Plug

1 x COM Port Header

•

1 x Chassis Intrusion and Speaker Header

•

1 x CPU Fan Connector (3-pin)

•

1 x Chassis Fan Connector (3-pin)

•

1 x 24 pin ATX Power Connector

•

1 x Front Panel Audio Connector

•

English

BIOS Feature

Hardware Monitor

Certications

2 x USB 2.0 Headers (Support 3 USB 2.0 ports) (Supports ESD

•

Protection) 1 x USB 3.1 Gen1 Header (Supports 2 USB 3.1 Gen1 ports)

•

(Supports ESD Protection)

* USB3_0_1 is shared with USB_0_1.

AMI UEFI Legal BIOS with GUI support

•

Supports Plug and Play

•

ACPI 5.0 compliant wa ke up events

•

Supports jumperfree

•

SMBIOS 3.0 support

•

CPU/Chassis temperature sensing

•

CPU/Chassis Fan Tachometer

•

CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by

•

CPU temperature) CPU/Chassis Fan multi-speed control

•

CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore

•

Microso® Windows® 10 64-bit

•

FCC, CE

•

ErP/EuP ready (ErP/EuP ready power supply is required)

•

English

* For detailed product infor mation, plea se visit our website: http://www.asrock.com

1.3 Motherboard Layout

PCIE1

ATXPWR1

AUDIO CODEC

DDR4_A1

DDR4_B1

CPU_FAN1

COM1

RoHS

HD_AUDIO1

BIOS ROM

Front USB 3.0

LAN

CLRMOS1

USB3_0_1

141516

USB_0_1

SATA3_1

SATA3

_A1

RJ-45 LAN

USB 2.0 T: USB0 B: USB1

PS2

Keyb oard

PS2

Mous e

CMOS

Battery

PANEL1

HDLED RES ET

PLED PWRB TN

SATA3_

SATA3

_A2

USB_2

SPK_CI1

HDM I1

VGA1

DVI 1

USB 3.1 Gen1 T: USB0 B: USB1

Top:

Central/Bass

Cente r:

REAR SP K

Top:

LINE IN

Cente r:

FRONT

Botto m:

Optic al

SPDIF

Botto m:

MIC IN

J5005-ITX J4105-ITX

English

No. Description

1 CPU Fan Connector (CPU_FAN1)

2 ATX Power Connector (ATXPWR1)

3 System Panel Header (PANEL1)

4 2 x 260-pin DDR4 SO-DIMM Slots (DDR4_A1, DDR4_B1)

5 Chassis Intrusion and Speaker Header (SPK_CI1)

6 Clear CMOS Jumper (CLRMOS1)

7 Chassis Fan Connector (CHA_FAN1)

8 COM Port Header (COM1)

9 USB 2.0 Header (USB_0_1)

10 USB 3.1 Gen1 Header (USB3_0_1)

11 USB 2.0 Header (USB_2)

12 SATA3 Connector (SATA3_1)

13 SATA3 Connector (SATA3_2)

14 SATA3 Connector (SATA3_A2)

15 SATA3 Connector (SATA3_A1)

16 Front Panel Audio Header (HD_AUDIO1)

English

1.4 I/O Panel

J5005-ITX J4105-ITX

547

No. Description No. Description

1 PS/2 Mouse Port 8 Microphone (Pink)

2 D-Sub Port 9 Optical SPDIF Out Port

3 LAN RJ-45 Port* 10 USB 2.0 Ports (USB_01)

4 Central / Bass (Orange) 11 USB 3.1 Gen1 Ports (USB3_01)

5 Rear Speaker (Black) 12 HDMI Port

6 Line In (Light Blue) 13 DVI-D Port

7 Front Speaker (Lime)** 14 PS/2 Keyboard Port

1012 1113

English

* ere are two LEDs on each LAN port. Ple ase refer to the table below for the LAN port LED indications.

ACT/LINK LED

SPEED LED

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection

** If you use a 2- channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See the table below

for connection details in accordance with the type of s peaker you use.

English

Audio Output

Channels

Front Speaker

(No. 7)

Rear Speaker

(No. 5)

Central / Bass

(No. 4)

2 V -- -- -- 4 V V -- -- 6 V V V -- 8 V V V V

To enable Multi-Streaming, you need to connect a front panel audio cabl e to the front panel au dio header. Aer restarting your computer, you will nd the “Mixer” tool on your system. Please selec t “Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to sel ect “Realtek HDA Primary output” to use the Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output ” to use the front panel audio.

Line In

(No. 6)

Chapter 2 Installation

is is a Mini-ITX form factor motherboard. Before you install the motherboard,

study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard.

•

Failure to do so may cause physical injuries to you and damages to motherboard

components.

In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.

When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

J5005-ITX J4105-ITX

English

2.1 Installation of Memory Modules (SO-DIMM)

is motherboard provides two 260-pin DDR4 (Double Data Rate 4) SO-DIMM slots, and

supports Dual Channel Memory Technology.

1. It is not allowe d to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, thi s motherboard and SO -DIMM may be damaged.

2. e SO-DIMM only ts in one correct orientation. It will cause permanent dam age to the motherboard and the SO-DIMM if you force the SO-DIMM into the slot at incorrect orientation.

Supported DDR4 Non ECC SODIMM

Raw Card

A (1Rx8) B (2R x8) C (1Rx16)

Dual Channel Memory Conguration

English

DDR4_A1

DDR4_B1

Populated

J5005-ITX J4105-ITX

English

+ 37 hidden pages