ASRock IMB-180 Owner's Manual

IMB-180
User Manual
Version 1.0
Published July 2013
Copyright©2013 ASRock INC. All rights reserved.
1
Version 1.0
Published June 2013
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
e terms HDMITM and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Ma nagement Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see w ww.dtsc.ca.gov/hazardouswaste/ perchlorate”
ASRock Website: http://www.asrock.com
2
Contents
1 Introduction ....................................................... 5
1.1 Package Contents ......................................................... 5
1.2 Specications ................................................................. 6
1.3 Motherboard Layout ....................................................... 8
1.4 I/O Panel ........................................................................ 10
2 Installation ......................................................... 11
2.1 Screw Holes ................................................................... 11
2.2 Pre-installation Precautions ........................................... 11
2.3 Installation of Memory Modules (DIMM) ........................ 12
2.4 Expansion Slots ............................................................ 13
2.5 Jumpers Setup ............................................................... 15
2.6 Onboard Headers and Connectors ................................ 16
2.7 Driver Installation Guide ............................................ 21
3 UEFI SETUP UTILITY ......................................... 22
3.1 Introduction .................................................................... 22
3.1.1 UEFI Menu Bar .................................................... 22
3.1.2 Navigation Keys ................................................... 23
3.2 Main Screen ................................................................... 23
3.3 Advanced Screen ........................................................... 24
3.3.1 CPU Conguration ............................................... 25
3.3.2 Chipset Conguration........................................... 27
3.3.3 Storage Conguration .......................................... 29
3.3.4 Intel(R) Rapid Start Technology ........................... 30
3.3.5 Intel(R) Smart Connect Technology ..................... 31
3.3.6 AMT Conguration ............................................... 32
3.3.7 Super IO Conguration ........................................ 34
3.3.8 ACPI Conguration............................................... 35
3.3.9 USB Conguration ............................................... 36
3.3.10 Voltage Conguration .......................................... 37
3.4 Hardware Health Event Monitoring Screen ................... 38
3.5 Boot Screen ................................................................... 39
3.6 Security Screen ............................................................. 41
3.7 Exit Screen .................................................................... 42
3
4 Software Support .............................................. 43
4.1 Install Operating System ................................................ 43
4.2 Support CD Information ................................................. 43
4.2.1 Running Support CD ............................................ 43
4.2.2 Drivers Menu ........................................................ 43
4.2.3 Utilities Menu........................................................ 43
4.2.4 Contact Information .............................................. 43
4
Chapter 1: Introduction
Thank you for purchasing ASRock IMB-180 motherboard, a reliable motherboard
produced under ASRock’s consistently stringent quality control. It delivers excellent
performance with robust design conforming to ASRock’s commitment to quality and
endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-
by-step guide to the hardware installation. Chapter 3 and 4 contain the conguration
guide to BIOS setup and information of the Support CD.
Because the motherboard specications and the BIOS software might be
updated, the content of this manual will be subject to change without no-
tice. In case any modications of this manual occur, the updated version
will be available on ASRock website without further notice. You may nd
the latest VGA cards and CPU support lists on ASRock website as well.
ASRock website http://www.asrock.com
If you require technical support related to this motherboard, please visit
our website for specic information about the model you are using.
www.asrock.com/support/index.asp
1.1 Package Contents
ASRock IMB-180 Motherboard
(Mini-ITX Form Factor: 6.7-in x 6.7-in, 17.0 cm x 17.0 cm)
ASRock IMB-180 Driver CD
ASRock IMB-180 Jumper setting instruction
1 x I/O Panel Shield
5
1.2 Specications
Form Factor
Processor System
Expansion Slot
Memory
Graphics
Ethernet
SATA
Rear I/O
Dimensions Mini-ITX (6.7-in x 6.7-in)
CPU
Core Number Max Speed (By CPU) L3 Cache (By CPU) Chipset QM87 BIOS UEFI PCI 0 Mini-PCIe 1 (Full size) mSATA 1 (Full size)
PCIe
CFast Card Socket
Technology
Max. 16GB Socket 2 x SO-DIMM Controller Intel® HD Graphics (By CPU) VRAM Shared Memory VGA Supports max resolution 2048x1536 LVDS 1 HDMI Supports HDMI 1.4a, max resolution 1920x1200 DVI No DisplayPort Supports max resolution 2560x1600 Multi Display Yes (Three Display) Ethernet 10/100/1000 Mbps
Controller
Connector 2 x RJ-45 Max Data Transfer Rate VGA 1 DVI 0 HDMI 1
Socket rPGA947 for Intel® Core i7/i5/i3/mobile processor (Haswell)
(By CPU, Max 4)
1 (x16) with Riser card extend to x8+x8 or x8+x4+x4
0
Dual Channel DDR3 1066/1333/1600 MHz SDRAM
GbE LAN1:Intel® I210, LAN2: Intel® I217LM (with v-Pro support)
SATA2 (3.0Gb/S), SATA3 (6.0Gb/S), Supports RAID 0/1/5/10
6
DisplayPort 2 Ethernet 2 USB 4 x USB 3.0 compliant Audio 2 (Mic-In, Line-Out) Serial 2 (RS-232/422/485) PS/2 0
USB
LVDS/ Inverter VGA 0 Serial 4 (RS-232)
SATA
Internal Connector
Watchdog Timer
Power Requirements
Environment Temperature 0ºC – 60ºC
mPCIe 1 Parallel 1 mSATA 1 IrDA 0 GPIO 8-bit 4 x GPI + 4 x GPO SATA PWR Output Con Speaker Header
Output Output from super I/O to drag RESETCON# Interval 256 Segments, 0,1,2…255 Sec/Min
Input PWR DC-in 12V~19V
Power On
- 8 (4 x USB Header 2.54mm pitch)
- 1 Vertical Type A USB Connector
24 bit dual channel LVDS
4 x SATA3 (6.0Gb/s), Support RAID 0/1/5/10
1
0
AT/ATX Supported
-AT : Directly PWR on as power input ready
-ATX : Press button to PWR on after power input ready
7
1.3 Motherboard Layout
DDR3_B 1
DDR3_A 1
PCIE1
AUDIO CODEC
BUZ Z1
CMOS
Batt ery
CPU_FA N1
CLRCOMOS 1
1
BIO S Chi p
PANEL 1
HDLED RESET
PLED P WRBTN
1
SATA3_3
CHA_FA N1
BLT_VOL1
1
BLT_PWR1
1
SPEAK ER1
1
1
USB4_5
1
HD_AU DIO1
BLT_PWM1
1
mi ni -PC Ie
IM B-1 80
18
21
23
24
1920
22
25
26
USB 12
1
CI1
JGPIO_PW R1
1
1
JGP IO1
Ro HS
Sup er
I/O
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
mi ni - SATA
1
USB6_7
1
USB8_9
1
USB10_11
DC_UPS 1
ATX12V1
SATA_PWR1
ATX_AT1
1
1
COM6
1
1 1
COM5
COM4
COM3
1
LPT1
PS2_K B_MS1
1
1
CI2
SATA3_4
SATA3_1
SATA3_2
LVDS1
1 1
PNL_PWR1
BKT_PWR1
DC_J ACK1
COM2
VGA1
DISP LAY2
HDMI1
RJ- 45
USB 3. 0 T: US B3 B: USB 2
1
TPM1
DISP LAY1
COM1
USB 3. 0
RJ- 45
T: US B1 B: USB 0
Bot to m:
Mic In
Top:
Lin e
Out
8
1 : ATX Power Connector
2 : 2-pin UPS Module Power Input Connector
3 : SATA Power Output Connector
4 : TPM Header
5 :
4-Pin CPU FAN Connector
6 :
3-Pin Chassis FAN Connector
7 : Digital Input / Output Power Select
8 : ATX/AT Mode Jumper
9 : RS-232 Port 4 Pin Headers
10 : Printer Port Header
11 : Digital Input / Output Pin Header
12 :
PS2_KB_MS1
Header
13 : Chassis Intrusion Headers
14 :
System Panel Header
15 : SATA3 Connectors
16 :
USB2.0 Connectors
17 : USB2.0 Port (USB12)
18 : Clear CMOS Header
19 : BKT_PWR1 Header
20 : PNL_PWR1 Header
21 : BLT_PWM1
Header
22 : 3W Audio AMP Output Wafer
23 :
Front Panel Audio Header
24 : LVDS Panel Connector
25 : Backlight Volume Control
26 :
Backlight Power Connector
9
1.4 I/O Panel
1
2 4
3
5
6
7
13
1 COM Port (COM1)
2 COM Port (COM2)
* 3 LAN RJ-45 Port (LAN1)
4 DisplayPort (DP2)
* 5 LAN RJ-45 Port (LAN2)
6 Line out (Lime)
7 Microphone (Pink)
* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED
indications.
Activity/Link LED SPEED LED
Status Description Status Description
12
LAN Port LED Indications
11
9
10
8 USB 3.0 Ports (USB_23)
9 HDMI Port (HDMI1)
10 USB 3.0 Ports (USB_01)
11 VGA Port (VGA1)
12 DisplayPort (DP1)
13 DC Jack (DC_JACK1)
ACT/LINK
LED
8
SPEED
LED
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection
LAN Port
10
Chapter 2: Installation
This is a Mini-ITX form factor (6.7" x 6.7", 17.0 x 17.0 cm) motherboard. Before you
install the motherboard, study the conguration of your chassis to ensure that the
motherboard ts into it.
motherboard. Failure to do so may cause physical injuries to you and
damages to motherboard components.
Make sure to unplug the power cord before installing or removing the
2.1 Screw Holes
Place screws into the holes to secure the motherboard to the chassis.
Do not over-tighten the screws! Doing so may damage the motherboard.
2.2 Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any component.
2. To avoid damaging the motherboard components due to static electricity,
NEVER place your motherboard directly on the carpet or the like. Also
remember to use a grounded wrist strap or touch a safety grounded object
before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded antistatic pad or
in the bag that comes with the component.
Before you install or remove any component, ensure that the power is
switched off or the power cord is detached from the power supply.
Failure to do so may cause severe damage to the motherboard, peripherals,
and/or components.
11
2.3 Installation of Memory Modules (SO-DIMM)
This motherboard provides two 204-pin DDR3 (Double Data Rate 3) SO-DIMM
slots.
It is not allowed to install a DDR or DDR2 memory module into DDR3
slot; otherwise, this motherboard and SO-DIMM may be damaged.
Installing a SO-DIMM
Please make sure to disconnect power supply before adding or
removing SO-DIMMs or the system components.
Step 1. Unlock a SO-DIMM slot by pressing the retaining clips outward.
Step 2. Align a SO-DIMM on the slot such that the notch on the SO-DIMM
matches the break on the slot.
notch
break
notch
The SO-DIMM only ts in one correct orientation. It will cause perma-
nent damage to the motherboard and the SO-DIMM if you force the SO-
DIMM into the slot at incorrect orientation.
break
Step 3. Firmly insert the SO-DIMM into the slot until the retaining clips at both
ends fully snap back in place and the SO-DIMM is properly seated.
12
2.4 Expansion Slots (PCI Express, mini-PCIe and mini-SATA
Slots)
There is 1 PCI Express slot, 1 mini-PCIe slot and 1 mini-SATA slot on this mother-
board.
PCIE slot: PCIE1 (PCIE x16 slot; Blue) is used for PCI Express x16 lane width
graphics cards.
A1 A82
B1 B82
Pin Side B Side A
1 +12V PRSNT#
2 +12V +12V
3 +12V +12V
4 Ground Ground
5 SMCLK PCH_ECLK_X8
6 SMDAT PCH_ECLK_X8#
7 Ground PCH_ECLK_X4
8 +3.3V PCH_ECLK_X4#
9 Reserved +3.3V
10 +3VSB +3.3V
11 WAKE# PCIE_RESET#
12 X8_PRSNT# Ground
13 Ground PCH_ECLK_X16
14 HSOP0 PCH_ECLK_X16#
15 HSON0 Ground
16 Ground HSIP0
17 PRSNT#1 HSIP0
18 Ground Ground
19 HSOP1 Reserved
20 HSON1 Ground
21 Ground HSIP1
22 Ground HSIP1
23 HSOP2 Ground
24 HSON2 Ground
25 Ground HSIP2
26 Ground HSIP2
27 HSOP3 Ground
28 HSON3 Ground
29 Ground HSIP3
30 X4_PRSNT# HSIP3
31 PRSNT#2 Ground
32 Ground Reserved
33 HSOP4 Reserved
34 HSON4 Ground
35 Ground HSIP4
36 Ground HSIP4
37 HSOP5 Ground
38 HSON5 Ground
39 Ground HSIP5
40 Ground HSIP5
41 HSOP6 Ground
Pin Side B Side A
42 HSON6 Ground
43 Ground HSIP6
44 Ground HSIP6
45 HSOP7 Ground
46 HSON7 Ground
47 Ground HSIP7
48 PRSNT#3 HSIP7
49 Ground Ground
50 HSOP8 Reserved
51 HSON8 Ground
52 Ground HSIP8
53 Ground HSIP8
54 HSOP9 Ground
55 HSON9 Ground
56 Ground HSIP9
57 Ground HSIP9
58 HSOP10 Ground
59 HSON10 Ground
60 Ground HSIP10
61 Ground HSIP10
62 HSOP11 Ground
63 HSON11 Ground
64 Ground HSIP11
65 Ground HSIP11
66 HSOP12 Ground
67 HSON12 Ground
68 Ground HSIP12
69 Ground HSIP12
70 HSOP13 Ground
71 HSON13 Ground
72 Ground HSIP13
73 Ground HSIP13
74 HSOP14 Ground
75 HSON14 Ground
76 Ground HSIP14
77 Ground HSIP14
78 HSOP15 Ground
79 HSON15 Ground
80 Ground HSIP15
81 PRSNT#4 HSIP15
82 Reserved Ground
13
Loading...
+ 30 hidden pages