ASRock H61MV-ITX User Manual [en, ru, fr, de, es]

Copyright Notice:
No part of this installation guide may be reproduced, transcribed, transmitted, or trans­lated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identifi ca- tion or explanation and to the owners’ benefi t, without intent to infringe.
Disclaimer:
Specifi cations and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commit­ment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or condi­tions of merchantability or fi tness for a particular purpose. In no event shall ASRock, its directors, offi cers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profi ts, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the pos­sibility of such damages arising from any defect or error in the guide or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com
Published November 2012
Copyright©2012 ASRock INC. All rights reserved.
ASRock H61MV-ITX Motherboard

English

1
Motherboard Layout
5
SATA_3(PORT5)
6
X
Fast USB
7
1
1
1
CPU_FAN1
PCIE1
8
9
USB4_5
USB6_7
CIR1
10
ATXPWR1
PLED PWRBTN
1
HDLED RESET
PANEL1
11
12
1
CI1
DDR3
13
H61MV-ITX
DDR3_B1 (64bit, 240-pin module)
DDR3_A1 (64bit, 240-pin module)
X
Fast RAM
X
Fast LAN
15
14
3
2
1
4
1
CLRCMOS1
32Mb BIOS
Battery
CHA_FAN1
CMOS
SATA_0(PORT0) SATA_2(PORT4)
SATA_1(PORT1)
RoHS
ATX12V1
HDMI_SPDIF1
1
16
Intel
H61
Keyboard
Mouse
PS2
PS2
21
VGA1
20
HDMI1
USB 2.0 T: U SB 0 B: USB1
19
USB 2.0
Top:
T: U SB 2
RJ-45
B: USB3
18
17
LAN
Bottom:
MIC IN
Top:
LINE IN
Center:
FRONT
HD_AUDIO1
1
AUDIO CODEC
English
2
1 Clear CMOS Jumper (CLRCMOS1) 12 2 x 240-pin DDR3 DIMM Slots 2 Chassis Fan Connector (CHA_FAN1) (Dual Channel: DDR3_A1, DDR3_B1) 3 SATA2 Connector (SATA_1 (PORT 1)) 13 System Panel Header (PANEL1) 4 SATA2 Connector (SATA_0 (PORT 0)) 14 1155-Pin CPU Socket 5 SATA2 Connector (SATA_2 (PORT 4)) 15 PCI Express 3.0 x16 Slot (PCIE1) 6 SATA2 Connector (SATA_3 (PORT 5)) 16 HDMI_SPDIF Header (HDMI_SPDIF1) 7 USB 2.0 Header (USB4_5) 17 Front Panel Audio Header (HD_AUDIO1) 8 USB 2.0 Header (USB6_7) 18 CPU Fan Connector (CPU_FAN1) 9 Consumer Infrared Module Header (CIR1) 19 ATX 12V Power Connector (ATX12V1) 10 ATX 12V Power Connector (ATX12V1) 20 Intel H61 Chipset 11 Chassis Intrusion Header (CI1) 21 32Mb SPI Flash
ASRock H61MV-ITX Motherboard
I/O Panel
1
2
3
4
5
10
1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB23) * 2 LAN RJ-45 Port 7 USB 2.0 Ports (USB01) 3 Line In (Light Blue) 8 HDMI Port ** 4 Front Speaker (Lime) 9 D-Sub Port 5 Microphone (Pink) 10 PS/2 Keyboard Port (Purple)
* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.
Activity/Link LED SPEED LED
Status Description Status Description
9
LAN Port LED Indications
8
7
6
ACT/LINK LED
SPEED LED
Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection
LAN Port
** To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. Please refer to below steps for the software setting of Multi-Streaming. For Windows® XP: After restarting your computer, you will fi nd “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or
“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then reboot your system. For Windows After restarting your computer, please double-click “Realtek HD Audio Manager” on the system tray. Set “Speaker Confi guration” to “Quadraphonic” or “Stereo”. Click “Device advanced settings”, choose “Make front and rear output devices playbacks two different audio streams simultaneously”, and click “ok”. Then reboot your system.
®
8 / 7 / VistaTM:
ASRock H61MV-ITX Motherboard
English
3
1. Introduction
Thank you for purchasing ASRock H61MV-ITX motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. This Quick Installation Guide contains introduction of the motherboard and step-by­step installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.
Because the motherboard specifi cations and the BIOS software might be updated, the content of this manual will be subject to change without no­tice. In case any modifi cations of this manual occur, the updated version will be available on ASRock website without further notice. You may fi nd the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com If you require technical support related to this motherboard, please visit our website for specifi c information about the model you are using. www.asrock.com/support/index.asp
1.1 Package Contents
ASRock H61MV-ITX Motherboard (Mini-ITX Form Factor) ASRock H61MV-ITX Quick Installation Guide ASRock H61MV-ITX Support CD 2 x Serial ATA (SATA) Data Cables (Optional) 1 x I/O Panel Shield
English
4
ASRock Reminds You...
To get better performance in Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista VistaTM 64-bit, it is recommended to set the BIOS option in Storage Con­ guration to AHCI mode. For the BIOS setup, please refer to the “User Manual” in our support CD for details.
TM
ASRock H61MV-ITX Motherboard
/
1.2 Specifi cations
Platform - Mini-ITX Form Factor
- All Solid Capacitor design
CPU - Supports 3 LGA1155 Package
- Supports Intel
- Supports K-Series unlocked CPU Chipset - Intel® H61
- Supports Intel® Rapid Start Technology and Smart Connect Technology Memory - Dual Channel DDR3 Memory Technology
- 2 x DDR3 DIMM slots
- Supports DDR3 1600/1333/1066 non-ECC, un-buffered memory (DDR3 1600 with Intel 1333 with Intel® Sandy Bridge CPU)
- Max. capacity of system memory: 16GB (see CAUTION 1)
- Supports Intel Intel® Ivy Bridge CPU Expansion Slot - 1 x PCI Express 3.0 x16 slot (PCIE1 @ x16 mode)
* PCIE 3.0 is only supported with Intel® Ivy Bridge CPU. With Intel® Sandy Bridge CPU, it only supports PCIE 2.0.
Graphics * Intel be supported only with processors which are GPU integrated.
- Supports Intel® HD Graphics Built-in Visuals: Intel® Quick Sync Video 2.0, Intel Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000 with Intel® Ivy Bridge CPU
- Supports Intel® HD Graphics Built-in Visuals: Intel® Quick Sync Video, Intel Technology, Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) with Intel® Sandy Bridge CPU
- Pixel Shader 5.0, DirectX 11 with Intel® Ivy Bridge CPU. Pixel Shader 4.1, DirectX 10.1 with Intel® Sandy Bridge CPU.
- Max. shared memory 1760MB with Intel Max. shared memory 1759MB with Intel CPU.
- Dual VGA Output: support HDMI and D-Sub ports by independent display controllers
rd
and 2nd Generation Intel® CoreTM i7 / i5 / i3 in
®
Turbo Boost 2.0 Technology
®
Ivy Bridge CPU, DDR3
®
Extreme Memory Profi le (XMP) 1.3 / 1.2 with
®
HD Graphics Built-in Visuals and the VGA outputs can
®
InTruTM 3D, Intel® Clear Video HD
®
InTruTM 3D, Intel® Clear Video HD
®
Ivy Bridge CPU.
®
Sandy Bridge
English
ASRock H61MV-ITX Motherboard
5
English
- Supports HDMI 1.4a Technology with max. resolution up to 1920x1200 @ 60Hz
- Supports D-Sub with max. resolution up to 2048x1536 @ 75Hz
- Supports Auto Lip Sync, xvYCC and HBR (High Bit Rate Audio) with HDMI (Compliant HDMI monitor is required) (see CAUTION 2)
- Supports HDCP function with HDMI port
- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback with HDMI port
Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Supports Wake-On-LAN
- Supports LAN Cable Detection
- Supports Energy Effi cient Ethernet 802.3az
- Supports PXE Rear Panel I/O I/O Panel
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x D-Sub Port
- 1 x HDMI Port
- 4 x Ready-to-Use USB 2.0 Ports
- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)
- HD Audio Jack: Line in / Front Speaker / Microphone Connector - 4 x SATA2 3.0 Gb/s connectors, support NCQ, AHCI and Hot Plug functions
- 1 x CIR header
- 1 x HDMI_SPDIF header
- 1 x Chassis Intrusion header
- 1 x CPU Fan connectors (4-pin)
- 1 x Chassis Fan connector (3-pin)
- 24 pin ATX power connector
- 4 pin 12V power connector
- Front panel audio connector
- 2 x USB 2.0 headers (support 4 USB 2.0 ports) BIOS Feature - 32Mb AMI UEFI Legal BIOS with GUI support
- Supports “Plug and Play”
- ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
6
ASRock H61MV-ITX Motherboard
- SMBIOS 2.3.1 Support Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), CyberLink MediaEspresso 6.5 Trial, Google Chrome Browser and Toolbar Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing
- CPU Fan Tachometer
- Chassis Fan Tachometer
- CPU Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by CPU Temperature)
- CPU Fan Multi-Speed Control
- CASE OPEN detection
- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore OS - Microsoft
®
Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista
TM
/
VistaTM 64-bit / XP / XP 64-bit compliant Certi cations - FCC, CE, WHQL
- ErP/EuP Ready (ErP/EuP ready power supply is required)
* For detailed product information, please visit our website: http://www.asrock.com
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.
CAUTION!
1. Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 8 / 7 / VistaTM / XP. For Windows® OS with 64­bit CPU, there is no such limitation.
RAM to utilize the memory that Windows® cannot use.
2. xvYCC is only supported under Windows® 8 64-bit / 8 / 7 64-bit / 7. HBR is supported under Windows® 8 64-bit / 8 / 7 64-bit / 7 /
TM
Vista
64-bit / VistaTM.
ASRock H61MV-ITX Motherboard
You can use ASRock XFast
English
7
1.3 Pin Header Easy Installation Guide
ASRock motherboard is equipped with pin headers with obvious colors which indi­cate you to recognize the crucial headers more easily. Please refer to below illustra­tions for the pin defi nition of onboard headers. If you want to have more information about the usage of these headers, please refer to “Jumpers Setup“ and “Onboard Headers and Connectors“ for details.
USB_PWR
P-
P+
GND
DUMMY
1
GND
P+
P-
USB_PWR
USB 2.0 Header
PLED+
PLED-
PWRBTN#
1
GND
HDLED-
HDLED+
System Panel Header
GND
REST#
DUMMY
English
8
HDMI_SPDIF Header
GND
PRESENCE#
MIC_RET
OUT_RET
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
Front Panel Audio Header
1
GND
ASRock H61MV-ITX Motherboard
1.4 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.
Jumper Setting Description
Clear CMOS Jumper
(CLRCMOS1) (see p.2, No. 1)
Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug
the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just fi nish updating the BIOS, you must boot up the system fi rst, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time and user default profi le will be cleared only if the CMOS battery is removed.
Clear CMOSDefault
If you clear the CMOS, the case open may be detected. Please adjust
the BIOS option “Clear Status” to clear the record of previous chassis intrusion status.
ASRock H61MV-ITX Motherboard
English
9
1.5 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!
Serial ATA2 Connectors These four Serial ATA2
(SATA_0 (PORT 0):
see p.2, No. 4)
(SATA_1 (PORT 1):
see p.2, No. 3)
(SATA_2 (PORT 4):
see p.2, No. 5)
(SATA_3 (PORT 5):
see p.2, No. 6)
Serial ATA (SATA) Either end of the SATA data Data Cable cable can be connected to the
(Optional)
SATA2 connector on this motherboard.
USB 2.0 Headers Besides four default USB 2.0
(9-pin USB4_5)
(see p.2 No. 7)
this motherboard. Each USB 2.0 header can support two USB 2.0 ports.
(9-pin USB6_7) (see p.2 No. 8)
(SATA2) connectors support
SATA_0 (PORT 0) SATA_2 (PORT 4)
SATA data cables for internal
storage devices. The current
SATA2 interface allows up to
SATA_1 (PORT 1) SATA_3 (PORT 5)
3.0 Gb/s data transfer rate.
SATA / SATA2 hard disk or the
ports on the I/O panel, there are two USB 2.0 headers on
English
10
Consumer Infrared Module Header This header can be used to
(4-pin CIR1)
(see p.2 No. 9)
connect the remote
controller receiver.
ASRock H61MV-ITX Motherboard
Front Panel Audio Header This is an interface for front
(9-pin HD_AUDIO1)
(see p.2 No. 17)
panel audio cable that allows
convenient connection and
control of audio devices.
1
GND
PRESENCE#
MIC2_R
MIC2_L
MIC_RET
J_SENSE
OUT2_R
OUT_RET
OUT2_L
1. High Defi nition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio header as below:
A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
E. To activate the front mic. For Windows
®
XP / XP 64-bit OS:
Select “Mixer”. Select “Recorder”. Then click “FrontMic”.
For Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Go to the "FrontMic" Tab in the Realtek Control panel. Adjust
“Recording Volume”.
System Panel Header This header accommodates
(9-pin PANEL1)
(see p.2 No. 13)
several system front panel
functions.
Connect the power switch, reset switch and system status indicator on the
chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may confi gure
the way to turn off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset
switch to restart the computer if the computer freezes and fails to perform a normal restart.
ASRock H61MV-ITX Motherboard
English
11
PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED
is on when the system is operating. The LED keeps blinking when the sys­tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED
is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly
consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.
Chassis Fan Connector Please connect the fan cables
(3-pin CHA_FAN1)
(see p.2 No. 2)
to the fan connectors and
match the black wire to the
ground pin.
English
12
CPU Fan Connectors Please connect the CPU fan
(4-pin CPU_FAN1)
(see p.2 No. 18)
cable to the connector and
match the black wire to the
ground pin.
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected
3-Pin Fan Installation
ATX Power Connector Please connect an ATX power
(24-pin ATXPWR1)
(see p.2 No. 10)
supply to this connector.
24 13
12 1
ASRock H61MV-ITX Motherboard
Though this motherboard provides 24-pin ATX power connector, it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.
24 13
20-Pin ATX Power Supply Installation
12 1
ATX 12V Power Connector Please connect an ATX 12V
(4-pin ATX12V1)
(see p.2 No. 19)
power supply to this connector.
HDMI_SPDIF Header HDMI_SPDIF header, providing
(2-pin HDMI_SPDIF1)
see p.2 No. 16)
(
VGA card, allows the system to
SPDIF audio output to HDMI
1
SPDIFOUT
GND
connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header.
Chassis Intrusion Header This motherboard supports
(2-pin CI1)
CASE OPEN detection feature
(see p.2, No. 11)
that detects if the chassis cover
1
Signal
GND
has been removed. This feature requires a chassis with chassis intrusion detection design.
ASRock H61MV-ITX Motherboard
English
13
2. BIOS Information
The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the prede­termined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF fi le) contained in the Support CD.
3. Software Support CD information
®
This motherboard supports various Microsoft 64-bit / 7 / 7 64-bit / VistaTM / Vista came with the motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the fi le “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.
TM
64-bit / XP / XP 64-bit. The Support CD that
Windows® operating systems: 8 / 8
English
14
ASRock H61MV-ITX Motherboard
Spezifi kationen
Plattform - Mini-ITX-Formfaktor
- Alle Feste Kondensatordesign CPU - Unterstützt Intel und 2ten Generation im LGA1155-Package
- Unterstützt Intel
- Unterstützt freigegebene CPU der K-Serie Chipsatz - Intel® H61
- Unterstützt Intel® Rapid Start Technology und Smart Connect Technology Speicher - Unterstützung von Dual-Kanal-Speichertechnologie
- 2 x Steckplätze für DDR3
- Unterstützt DDR3 1600/1333/1066 non-ECC, ungepufferter Speicher (DDR3 1600 mit Intel DDR3 1333 mit Intel® Sandy Bridge-Prozessor)
- Max. Kapazität des Systemspeichers: 16GB
- Unterstützt Intel Intel® Ivy Bridge-Prozessor Erweiterungs- - 1 x PCI Express 3.0 x16-Steckplatz (PCIE1 für x16-Modus) steckplätze * PCIE 3.0 wird nur mit Intel® Ivy Bridge-Prozessor unterstützt. Mit Intel® Sandy Bridge-Prozessor wird nur PCIE 2.0 unterstützt. Onboard-VGA * Integrierte Intel Ausgänge können nur durch GPU-integrierte Prozessoren unterstützt werden.
- Unterstützt hochaufl ösende integrierte Intel Intel® Quick-Sync-Video 2.0, Intel® InTruTM 3D, Intel® Clear­ Video-Technik (HD), Intel® InsiderTM, Intel® HD Graphics 2500/4000 mit Intel® Ivy Bridge-Prozessor
- Unterstützt hochaufl ösende integrierte Intel Intel® Quick-Sync-Video, Intel® InTruTM 3D, Intel® Clear­ Video-Technik (HD), Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) mit Intel® Sandy Bridge­ Prozessor
- Pixel Shader 5.0, DirectX 11 mit Intel Pixel Shader 4.1, DirectX 10.1 mit Intel® Sandy Bridge­ Prozessor
- Maximal gemeinsam genutzter Speicher 1760MB mit Intel Ivy Bridge-Prozessor. Maximal gemeinsam genutzter Speicher 1759MB mit Intel® Sandy Bridge-Prozessor.
®
CoreTM i7- / i5- / i3-Prozessoren der 3ten
®
Turbo Boost 2.0-Technologie
®
Ivy Bridge-Prozessor,
®
Extreme Memory Profi le (XMP)1.3/1.2 mit
®
HD-Grafi kdarstellungen und die VGA-
®
-Grafi klösungen:
®
-Grafi klösungen:
®
Ivy Bridge-Prozessor,
®
Deutsch
ASRock H61MV-ITX Motherboard
15
Deutsch
- Doppel-VGA Ausgabe: unterstützt HDMI und D-Sub Ports durch unabhängige Bildschirmanzeige Kontrolleure
- Unterstützt HDMI 1.4a mit einer maximalen Aufl ösung von 1920 x 1200 bei 60 Hz
- Unterstützt D-Sub mit einer maximalen Aufl ösung von 2048 x 1536 bei 75 Hz
- Unterstützt Auto Lip Sync, Deep Color (12bpc), xvYCC und HBR (High Bit Rate-Audio) mit HDMI (kompatibler HDMI- Bildschirm erforderlich)
- Unterstützt HDCP-Funktion mit HDMI-Port
- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe mit HDMI-Port
Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Unterstützt Wake-On-LAN
- Unterstützt LAN-Kabelerkennung
- Unterstützt energieeffi zientes Ethernet 802.3az
- Unterstützt PXE E/A-Anschlüsse I/O Panel an der - 1 x PS/2-Mausanschluss Rückseite - 1 x PS/2-Tastaturanschluss
- 1 x D-Sub port
- 1 x HDMI port
- 4 x Standard-USB 2.0-Anschlüsse
- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED LED)
- HD Audiobuchse: Audioeingang / Lautsprecher vorne / Mikrofon Anschlüsse - 4 x SATA2 3,0 GB/s-Anschlüsse, unterstützen NCQ-, AHCI- und „Hot Plug“ (Hot-Plugging)- Funktionen
- 1 x
- 1 x HDMI_SPDIF-Anschluss
- 1 x Verteiler für Gehäuseeindringversuche
- 1 x CPUlüfter-Anschluss (4-pin)
- 1 x Gehäuselüfter-Anschluss (3-pin)
- 24-pin ATX-Netz-Header
- 4-pin anschluss für 12V-ATX-Netzteil
- Anschluss für Audio auf der Gehäusevorderseite
- 2 x USB 2.0-Anschlüsse (Unterstützung 4 zusätzlicher USB 2.0-Anschlüsse)
Consumer Infrared-Modul-Header
16
ASRock H61MV-ITX Motherboard
Loading...
+ 35 hidden pages