ASRock A520M Phantom Gaming 4 operation manual

Version 1.0
Published August 2020
Copyright©2020 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see ww w.dtsc.ca.gov/hazardouswaste/ perchlorate”
ASRock Website: http://www.asrock.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply)
e terms HDMI® and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specications 2
1.3 Motherboard Layout 6
1.4 I/O Panel 8
Chapter 2 Installation 10
2.1 Installing the CPU 11
2.2 Installing the CPU Fan and Heatsink 13
2.3 Installing Memory Modules (DIMM) 21
2.4 Expansion Slots (PCI Express Slots) 24
2.5 Jumpers Setup 25
2.6 Onboard Headers and Connectors 26
2.7 M.2_SSD (NGFF) Module Installation Guide (M2_1) 31
2.8 M.2_SSD (NGFF) Module Installation Guide (M2_2) 34
Chapter 3 Software and Utilities Operation 37
3.1 Installing Drivers 37
3.2 ASRock Motherboard Utility (Phantom Gaming Tuning) 38
3.2.1 Installing ASRock Motherboard Utility (Phantom Gaming Tuning) 38
3.2.2 Using ASRock Motherboard Utility (Phantom Gaming Tuning) 38
3.3 ASRock Live Update & APP Shop 41
3.3.1 UI Overview 41
3.3.2 Apps 42
3.3.3 BIOS & Drivers 45
3.3.4 Setting 46
3.4 ASRock Polychrome SYNC 47
Chapter 4 UEFI SETUP UTILITY 50
4.1 Introduction 50
4.1.1 UEFI Menu Bar 50
4.1.2 Navigation Keys 51
4.2 Main Screen 52
4.3 OC Tweaker Screen 53
4.4 Advanced Screen 56
4.4.1 CPU Conguration 57
4.4.2 Onboard Devices Conguration 58
4.4.3 Storage Conguration 60
4.4.4 ACPI Conguration 61
4.4.5 Trusted Computing 62
4.4.6 AMD PBS 63
4.4.7 AMD CBS 64
4.5 Tools 65
4.6 Hardware Health Event Monitoring Screen 66
4.7 Security Screen 68
4.8 Boot Screen 69
4.9 Exit Screen 71
A520M Phantom Gaming 4
Chapter 1 Introduction
ank you for purchasing ASRock A520M Phantom Gaming 4 motherboard, a
reliable motherboard produced under ASRock’s consistently stringent quality
control. It delivers excellent performance with robust design conforming to
ASRock’s commitment to quality and endurance.
In this documentation, Chapter 1 and 2 contains the introduction of the
motherboard and step-by-step installation guides. Chapter 3 contains the operation
guide of the soware and utilities. Chapter 4 contains the conguration guide of
the BIOS setup.
Becau se the motherboard specications and the BIOS soware might be updated, the content of this documentation will be subject to change without notice. In case any modi­cations of this documentation occur, the updated version will be available on ASRock’s website w ithout further notice. If you require technical support related to this mother­board, please visit our website for specic information about the model you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock website http://www.asrock.com.
1.1 Package Contents
ASRock A520M Phantom Gaming 4 Motherboard (Micro ATX Form Factor)
•
ASRock A520M Phantom Gaming 4 Quick Installation Guide
•
ASRock A520M Phantom Gaming 4 Support CD
•
1 x I/O Panel Shield
•
2 x Serial ATA (SATA) Data Cables (Optional)
•
2 x Screws for M.2 Sockets (Optional)
•
English
1
English
1.2 Specications
Platform
CPU
Chipset
Memory
•
•
•
•
* Not compatible with AMD Ryzen™ 5 3400G and Ryzen™ 3
3200G.
•
•
•
•
•
•
•
* Please refer to Memory Support List on ASRock’s website for
more information. (http://www.asrock.com/)
* Please refer to page 22 for DDR4 UDIMM maximum
frequency support.
•
•
•
Micro ATX Form Factor
Solid Capacitor design
2oz Copper PCB
Supports 3rd Gen AMD AM4 Ryzen™ / future AMD Ryzen™
Processors (3000 and 4000 Series Processors)*
Digi Power design
8 Power Phase design
AMD A520
Dual Channel DDR4 Memory Technology
4 x DDR4 DIMM Slots
AMD Ryzen series CPUs (Matisse) support DDR4
4533+(OC)/4466(OC)/440 0(OC)/4333(OC)/4266(OC)/
420 0(OC)/4133(OC)/40 00(OC)/3866(OC)/3800(OC)/3733
(OC)/3600(OC)/3466(OC)/3200/2933/2667/2400/2133 ECC
& non-ECC, un-buered memory*
AMD Ryzen series APUs (Renoir) support DDR4 4733+
(OC)/4666(OC)/4600(OC)/4533(OC)/4466(OC)/
4400(OC)/4333(OC)/4266(OC)/4200(OC)/4133(OC)/
4000(OC)/3866(OC)/380 0(OC)/3733(OC)/3600(OC)/
3466(OC)/3200/2933/2667/2400/2133 ECC & non-ECC, un-
buered memory*
Max. capacity of system memory: 128GB
Supports Extreme Memory Prole (XMP) memory modules
15μ Gold Contact in DIMM Slots
Expansion Slot
2 x PCI Express 3.0 x16 Slots (PCIE1: x16 mode; PCIE3: x2
mode)*
* Supports NVMe SSD as boot disks
1 x PCI Express 3.0 x1 Slot
•
2
Graphics
A520M Phantom Gaming 4
Integrated AMD RadeonTM Vega Series Graphics in Ryzen
•
Series APU*
* Actual support may vary by CPU
DirectX 12, Pixel Shader 5.0
•
Shared memor y default 2GB. Max Shared memory supports
•
up to 16GB.
* e Max shared memory 16GB requires 32GB system
memory installed.
Dual graphics output: support HDMI and DisplayPort 1.4
•
ports by independent display controllers
Supports HDMI 2.1 with max. resolution up to 4K x 2K
•
(4096x2160) @ 60Hz
Supports DisplayPort 1.4 with max. resolution up to 5K
•
(5120x2880)@120Hz
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
•
HBR (High Bit Rate Audio) with HDMI 2.1 Port (Compliant
HDMI monitor is required)
Supports HDR (High Dynamic Range) with HDMI 2.1
•
Supports HDCP 2.3 with HDMI 2.1 and DisplayPort 1.4
•
Ports
Supports 4K Ultra HD (UHD) playback with HDMI 2.1 and
•
DisplayPort 1.4 Ports
Supports Microso PlayReady®
•
Audio
LAN
7.1 CH HD Audio (Realtek ALC 887/897 Audio Codec)
•
Supports Surge Protection
•
PCIE x1 Gigabit LAN 10/100/1000 Mb/s
•
Realtek RTL8111H
•
Supports Wake-On-LAN
•
Supports Lightning/ESD Protection
•
Supports Energy Ecient Ethernet 802.3az
•
Supports PXE
•
English
3
English
Rear Panel I/O
Storage
Connector
1 x PS/2 Mouse/Keyboard Port
•
1 x HDMI Port
•
1 x DisplayPort 1.4
•
4 x USB 3.2 Gen1 Ports (Supports ESD Protection)
•
2 x USB 2.0 Ports (Supports ESD Protection)
•
1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
•
LED)
HD Audio Jacks: Line in / Front Speaker / Microphone
•
4 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,
•
RAID 1 and RAID 10), NCQ, AHCI and Hot Plug*
* M2_ 2 and SATA3_3_4 share lanes. If either one of them is in
use, the other one will be disabled.
1 x Ultra M.2 Socket (M2_1), supports M Key ty pe 2280 M.2
•
PCI Express module up to Gen3 x4 (32 Gb/s)**
1 x M.2 Socket (M2_2), supports M Key type 2280 M.2
•
SATA3 6.0 Gb/s module and M.2 PCI Express module up to
Gen3 x2 (16 Gb/s)**
** Supports NVMe SSD as boot disks
** Supports ASRock U.2 Kit
1 x SPI TPM Header
•
1 x Power LED and Speaker Header
•
2 x RGB LED Headers
•
* Support in total up to 12V/3A, 36W LED Strip
2 x Addressable LED Headers
•
* Support in total up to 5V/3A, 15W LED Strip
1 x CPU Fan Connector (4-pin)
•
* e CPU Fan Connector supports the CPU fan of ma ximum
1A (12W) fan power.
3 x Chassis/Water Pump Fan Connectors (4-pin) (Smart
•
Fan Speed Control)
* e Chassis/Water Pump Fan supports the water cooler fan
of maximum 2A (24W) fan power.
* CHA_FAN1/WP, CHA_FAN2/WP and CHA_FAN3/WP can
auto detect if 3-pin or 4-pin fan is in use.
1 x 24 pin ATX Power Connector
•
1 x 8 pin 12V Power Connector
•
1 x Front Panel Audio Connector
•
4
BIOS Feature
Hardware Monitor
A520M Phantom Gaming 4
2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports
•
ESD Protection)
1 x USB 3.2 Gen1 Header (Supports 2 USB 3.2 Gen1 port)
•
(Supports ESD Protection)
AMI UEFI Legal BIOS with GUI support
•
Supports “Plug and Play”
•
ACPI 5.1 compliance wake up events
•
Supports jumperfree
•
SMBIOS 2.3 support
•
CPU, CPU VDDCR_SOC, DRAM, +1.8VSB, Voltage Multi-
•
adjustment
Temperature Sensing: CPU, Chassis/Water Pump Fans
•
Fan Tachometer: CPU, Chassis/Water Pump Fans
•
Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
•
ture): CPU, Chassis/Water Pump Fans
Fan Multi-Speed Control: CPU, Chassis/Water Pump Fans
•
Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, CPU
•
VDDCR_SOC, DRAM, VPPM, +1.8V
Microso® Windows® 10 64-bit
OS
Certica­tions
* For detailed product information, please visit our website: http://www.asrock .com
Please realiz e that the re is a certain r isk involved with o verclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technolog y, or using third-party overclocking to ols. O verclocking may aect your system’s stability, or even c ause damage to the components and devices of your system. It should be don e at your ow n risk and expense. We are not responsibl e for possible damage caused by overclo cking.
•
FCC, CE
•
ErP/EuP ready (ErP/EuP ready power supply is required)
•
English
5
3
2
4
10
11
1
Sup er
I/O
CLRCMOS1
1
PCIE1
HD_AUDIO1
1
RJ- 45 LAN
SOCKETAM4
F_USB3 _1_2
1
CHA_FAN1/WP
1
RoHS
SPK_PLED1
1
DDR 4_A1 (6 4 bit, 288 -pin mo dule)
DDR 4_A2 (6 4 bit, 288 -pin mo dule)
DDR 4_B1 (6 4 bit, 288 -pin mo dule)
DDR 4_B2 (6 4 bit, 288 -pin mo dule)
PCIE2
PCIE3
HDLED RESET
PLED PWRBTN
PANEL1
M2_2
M2_1
AMD
Promontory
A520
1
23
USB 3.2 Gen1 T: USB3_3 B: USB3_4
USB 2.0 T: USB1 B: USB2
PS2
Keyboard/
Mouse
CPU_FAN1
CHA_FAN3/WP
21
20
22
USB 3.2 Gen1 T: USB3_1 B: USB3_2
ADDR_LED1
1
1
RGB_LED1
6
5
SATA3_1
SATA3_2
9
1
SPI_TPM_J1
18
CHA_FAN2 /WP
RGB_LED2
1
ADDR_LED2
1
CMOS
Battery
LAN
AUDIO CODEC
19
17 15
1
USB_3_4
16
USB_5_6
ATXP WR1
A5 2 0M P h a nt o m Ga m in g 4
ATX12V1
Top:
LINE IN
Center :
FRONT
Bottom :
MIC IN
HDMI1
DP1
SATA3_4
SATA3_3
Ultra M.2
PCIe Gen3x4
1.3 Motherboard Layout
7
English
8
12
13
14
6
A520M Phantom Gaming 4
No. Description
1 8 pin 12V Power Connector (ATX12V1)
2 CPU Fan Connector (CPU_FAN1)
3 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
4 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
5 RGB LED Header (RGB_LED1)
6 Addressable LED Header (ADDR_LED1)
7 ATX Power Connector (ATXPWR1)
8 USB 3.2 Gen1 Header (F_USB3_1_2)
9 SATA3 Connector (SATA3_2)
10 SATA3 Connector (SATA3_1)
11 SATA3 Connector (SATA3_4)(Upper), SATA3 Connector (SATA3_3)(Lower)
12 System Panel Header (PANEL1)
13 Power LED and Speaker Header (SPK_PLED1)
14 Chassis/Water Pump Fan Connector (CHA_FAN3/WP)
15 USB 2.0 Header (USB_3_4)
16 USB 2.0 Header (USB_5_6)
17 SPI TPM Header (SPI_TPM_J1)
18 Chassis/Water Pump Fan Connector (CHA_FAN2/WP)
19 Clear CMOS Jumper (CLRCMOS1)
20 Addressable LED Header (ADDR_LED2)
21 RGB LED Header (RGB_LED2)
22 Front Panel Audio Header (HD_AUDIO1)
23 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)
English
7
1.4 I/O Panel
3
1 2 4
6 578910
No. Description No. Description
1 USB 2.0 Ports (USB_12)* 6 USB 3.2 Gen1 Ports (USB3_34)
2 LAN RJ-45 Port** 7 USB 3.2 Gen1 Ports (USB3_12)
3 Line In (Light Blue)*** 8 PS/2 Mouse/Keyboard Port
4 Front Speaker (Lime)*** 9 DisplayPort 1.4
5 Microphone (Pink)*** 10 HDMI Port
* Please note that the USB_ 2 consumes auxiliary power (+5VSB) while the other USB por ts consume DUAL Power (+5VDUAL). e USB_ 2 is optimal for connecting the USB Type speaker and headset ..
English
8
** ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
LAN Por t
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection
A520M Phantom Gaming 4
*** Function of the Audio Ports in 7.1-channel Conguration:
Port Function
Light Blue (Rear panel) Rear Speaker Out Lime (Rear panel) Front Speaker Out Pink (Rear panel) Central /Subwoofer Speaker Out Lime (Front panel) Side Speaker Out
English
9
Chapter 2 Installation
is is a Micro ATX form factor motherboard. Before you install the motherboard,
study the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
Make sure to unplug the power cord before installing or removing the motherboard.
•
Failure to do so may cause physical injuries to you and damages to motherboard
components.
In order to avoid damage from static electricity to the motherboard’s components,
•
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
Hold components by the edges and do not touch the ICs.
•
Whenever you uninstall any components, place them on a grounded anti-static pad or
•
in the bag that comes with the components.
When placing screws to secure the motherboard to the chassis, please do not over-
•
tighten the screws! Doing so may damage the motherboard.
English
10
2.1 Installing the CPU
Unplug all power cables be fore installing the CPU.
1
A520M Phantom Gaming 4
2
English
11
3
English
12
A520M Phantom Gaming 4
2.2 Installing the CPU Fan and Heatsink
Aer you install the CPU into this motherboard, it is necessary to install a larger
heatsink and cooling fan to dissipate heat. You also need to spray thermal grease
between the CPU and the heatsink to improve heat dissipation. Ma ke sure that the
CPU and the heatsink are securely fastened and in good contact with each other.
Please turn o the power or remove th e power cord before changing a CPU or heatsink.
Installing the CPU Box Cooler SR1
1
2
English
13
3
English
14
4
1
N
FA
_
U
P
C
Installing the AM4 Box Cooler SR2
1
A520M Phantom Gaming 4
2
English
15
3
English
16
A520M Phantom Gaming 4
4
1
N
FA
_ U
P
C
*e diagrams shown here are for reference only. e headers might be in a dierent position on
your motherboard.
17
English
Installing the AM4 Box Cooler SR3
1
English
18
2
A520M Phantom Gaming 4
4
3
English
19
Loading...
+ 55 hidden pages