Ariston ASL75CXS Care, Use and Installation booklet

0 (0)

Care, Use and Installation booklet

			TUMBLE DRYER

			Contents
EN	ES	F	Contents	EN
EN	ES	F		EN
			Warnings and Safety Instructions, 2
English 1	Español, 14	Français, 27	Warnings and Safety Instructions, 2
			Important safety instructions
			Grounding instructions
			Dryer Descriptions, 3
			To open door
			The features
			Control panel
			Start and Programs, 4-6
			Choosing a program
			Table of programs
			The controls
			Laundry, 7-8
			Sorting your laundry
ASL75CXS			Wash care labels

Special clothing items

Drying times

Maintenance and Care, 9

When to switch off the electricity

Clean the filter after each cycle

Check the drum after each cycle

Cleaning the dryer

Troubleshooting, 10

Spare parts

Installation, 11-12

Electrical

Where to put your dryer

Stacking kit

Warranties, 13

www.aristonappliances.us

Warnings and Safety Instructions

! The appliance has been designed and built according to international safety standards.

These warnings are given for safety reasons and must be read carefully.

Important safety instructions

WARNING:

To reduce the risk of fire, electric shock or injury to persons when using your appliance, follow the basic precautions, including the following:

●Read all instructions before using the appliance.

●Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents or other flammable or explosive substances, as they give off vapours that could ignite or explode.

●Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

●Before the appliance is removed from service or discarded, remove the door to the drying compartment.

●Do not reach into the appliance if the drum is moving.

●Do not install or store this appliance where it will be exposed to the weather.

●Do not tamper with the controls.

●Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions.

●Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

●Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

●Clean the lint filter before and after each load (see Maintenance).

●Keep the area around the exhaust opening and adjacent surroundings free from the accumulation of lint, dust and dirt.

●The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

●Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

●This tumble dryer has been designed for home, and not professional, use.

●This dryer must be used by adults, and the instructions in this booklet should be followed carefully.

●Do not touch the appliance while barefoot or with wet hands or feet.

●The appliance must be installed correctly and have proper ventilation. The air intake at the front of the dryer and the rear vents behind the machine should never be obstructed (see Installation).

●Check to see if the dryer is empty before loading it.

●The back of the dryer could become very hot. Never touch it while in use.

●Do not use the dryer unless the filter and condenser are securely in place (see Maintenance).

●Clean the condenser unit at regular intervals (see Maintenance).

●Do not overload the dryer (see Laundry for maximum loads).

●Do not load items that are dripping wet.

●Tumble dry items only if they have been washed with detergent and water, rinsed and been through the spin cycle. It is a fire hazard to dry items that have not been washed with water.

●Carefully check all instructions on clothing labels (see Laundry).

●Do not tumble dry large, very bulky items.

●Do not tumble dry acrylic fibres at high temperatures.

●Complete each program with its Air Fluff phase.

●Do not turn off the dryer when there are still warm items inside.

●Never climb on top of the dryer. It could result in damage.

●Comply with specified electrical requirements (see Installation).

●Always buy original spare parts and accessories (see Troubleshooting).

Grounding instructions (see Installation)

WARNING:

THIS APPLIANCE MUST BE GROUNDED. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the appliance is properly grounded!

In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DO NOT modify the plug provided with the appliance: if it will not fit the outlet, have a proper outlet installed by a qualified electrician or exchange the cord with an appropriate one rated for the dryer.

REFER TO THE RATING PLATE FOR VOLTAGE AND CURRENT REQUIREMENTS (see diagram for location). The dryer should be connected to the mains supply via a suitable socket which is accessible after installing your dryer. This dryer must be connected to 30A INDIVIDUAL BRANCH CIRCUIT.

For full details see Installation Instruction sections of this book.

IF IN DOUBT ABOUT ANY OF THE ABOVE CONSULT A QUALIFIED ELECTRICIAN

www.aristonappliances.us

SAVE THESE INSTRUCTIONS

Dryer Description

To open the door

The features

Rating plate

Press and release the front

panel in position shown

Door

Door catch

Air intake

grille

Condenser cover handle

Filter

(Pull to open)

Control panel

		START/CANCEL		On/Off
OPTION	Filter Care		Button
OPTION	Filter Care		Button
Buttons	Light	Indicator		Light
				Light

Programs Guide	Option	Progress or Delay	PROGRAMS	ON/OFF
	Lights	Lights	Knob	Button

The START/CANCEL button starts a selected program. When you press this button there will be one beep and the progress lights will flash to confirm the action. If you have not set a program, the buzzer will beep four times. When a program is running, holding in this button cancels the program and stops the dryer (see Start and Programs).

The OPTION buttons select available options for your selected program (see Start and Programs).

The Option lights indicate that the option has been selected by the button to the left of the appropriate light.

The Programs Guide gives you a guide to the available programs.

www.aristonappliances.us

The Clean Filter light gives a reminder before every program, that it is essential to clean the filter every time the dryer is used (see Maintenance and Care).

The On/Off indicator light signals that your dryer is in use or ready to select a program. If this light flashes it indicates there is a fault (see Troubleshooting).

The ON/OFF button: If the dryer is running and this button is pressed, the dryer stops. Press again, the dryer restarts.

The Progress or Delay lights show you the status of the program, or the delay time when they flash. During a delayed start the lights will flash to show the delay selected. When (not flashing) they show each stage of the program by the corresponding light turning on (see Start and Programs).

The PROGRAMS knob sets the program: rotate it until the indicator is pointing to the program you want to select (see Start and Programs).

Start and Programs

Choosing a program

1.Plug the dryer into the electrical socket.

2.Sort your laundry according to fabric type (see Laundry).

3.Open the door and make sure the filter is clean (see Maintenance).

4.Load the machine and make sure items are not in the way of the door seal. Close the door.

5.If the On/Off light is not lit: Press the ON/OFF button.

6.Choose a program by checking the Programs Guide (see Programs) as well as the indications for each type of fabric (see Laundry).

- Select a program by rotating the PROGRAMS knob.

7.Set a delay time and other options if necessary.

8.If you wish to select the buzzer, to sound at the end of the program, press the ALARM Option button.

9.Press the START button to begin.

During the drying program, you can check on your laundry and take out the items that are dry while others continue drying. When you close the door again, press the START button in order to resume drying.

10.During the last few minutes of Drying Programs, before the program is completed, the final AIR FLUFF phase is entered (fabrics are cooled), this phase should always be allowed to complete.

11.When the program is complete. The buzzer will sound if the Alarm option was selected.

Open the door, take your laundry out, clean the filter and replace it (see Maintenance).

If the Post Creasecare option has been selected and you do not take the clothes out immediately, the clothes will tumble occasionally for 10 hours or until you open the door.

12.Unplug the dryer.

Easy Iron Program

Easy Iron is a short 10 minute programme (8 minutes of heat followed by a 2 minute Air Fluff period) which fluffs the fibers of clothing that have been left in the same position/location for an extended period of time. The cycle relaxes the fibers and makes them easier to iron and fold.

! Easy Iron is not a drying program and should not be used for wet articles of clothing.

For best results:

1. Do not load more than the maximum capacity. These numbers refer to the dry weight:

Fabric	Maximum load
Regular Cotton and Regular Cotton mix	5.5 lb / 2.5 kg
Permanent Press	4 lb / 2 kg
Denim	4 lb / 2 kg

2.Unload the dryer immediately after the end of the program, hang, fold or iron the articles and put them away. Should this not be possible, repeat the program.

The Easy Iron effect varies from one fabric to the next. It works very well on traditional fabrics like Regular Cottons or Regular Cotton mix, and less well on acrylic fibers.

www.aristonappliances.us

Programs

! If the On/Off light is not lit; Press the ON/OFF button and then select program.

Program	What it does...	How to set it...			Note:

Sensor Dry	Dries your clothes on HIGH heat	1. Position the PROGRAMS knob			Options available:
	setting, ready for putting away.		on	.	Alarm, Delayed Start,
		2. Select any options, if required.			Pre-Creasecare,
Regular Cottons		3. Press the START button.			Post Creasecare.
Cupboard dry

Sensor Dry	Dries your clothes on LOW Heat	1.	Position the PROGRAMS knob		Options available:
	setting, ready for putting away.		on .		Alarm, Delayed Start,
		2.	Select any options, if required.		Pre-Creasecare,
Permanent Press		3.	Press the START button.		Post Creasecare.
Cupboard dry
Timed Drying	Dries wet clothing that you wish	1. Position the PROGRAMS knob on			Options available:
(160, 140, 120,	to dry on LOW Heat or small		the desired time: 160, 140, 120,		Alarm, High Heat, Delayed
	to dry on LOW Heat or small		the desired time: 160, 140, 120,		Start, Pre-Creasecare,
	loads (less than 2 lb / 1 kg).		100, 80, 70, 60, 50, 40, 30 or 20.
100, 80, 70, 60,
100, 80, 70, 60,					Post Creasecare.
50, 40, 30 or 20		2. Select any options, if required.			Post Creasecare.
50, 40, 30 or 20		2. Select any options, if required.
minutes)	Can be used with HIGH Heat	3. Press the START button.			Consult ‘suggested drying
	Can be used with HIGH Heat				times’ (see Laundry).
	option if you prefer to use a				times’ (see Laundry).
	option if you prefer to use a
	timed programme.				The last 10 minutes of these
					programs is the Air Fluff
					phase (see below).

	Brief program (approximately 10	1.	Position the PROGRAMS knob		Options available:
	minutes) that cools fibers of		on .		Alarm
Air Fluff	clothing.	2.	Select any options, if required.
Air Fluff		3.	Press the START button.

Fabric Care	Brief program (approximately 10	1.	Position the PROGRAMS knob		! This is not a drying
	minutes) that softens fibers of		on .		program (see previous
	clothing that is ready for ironing.	2.	Select any options, if required.		page).
		3.	Press the START button.
Easy Iron					Options available:
					Options available:
					Alarm

www.aristonappliances.us

Start and Programs

The Controls

● PROGRAMS knob

!Warning, if after pressing the start button, the programs knob position is changed, the new position will NOT change the program selected.

!Position 0, turning the programs knob to position 0 resets and cancels a program.

● OPTION buttons / lights

These buttons are used to customize the selected program to your requirements. A program must have been selected on the programs knob before an option can be selected. Not all options are available for all programs (see Start and Programs). If an option is not available and you press the button, the buzzer will beep four times. If the option is available there will be one beep and the option light next to the button lights to confirm the selection.

Progress (Drying, Air Fluff, Post Creasecare) / Delay (3hr 6hr 9hr 12hr) Lights

When the light next to the delay button is on, these lights flash to indicate the delay time is selected. During other programs they indicate the progress of the dryer, each one comes on as the corresponding phase starts.

Time Delay

The start of some programs (see Start and Programs) can be delayed for up to 12 hours in 3hr steps. When a delayed start is in progress the light next to the delay button will be on and the selected delay period light will flash (after the start button has been pressed). To set a delayed start, press the Time Delay button, and the light next to the button will come on together with the 3hr delay light. Pressing the button again will advance the delay setting to 6hr, the 3hr light goes out and the 6hr light is on. Each time you press the

button the delay setting advances 3 hours, as indicated by the corresponding light. If the 12hr light is on, pressing the button again will cancel the delay.

You can also cancel the delay by turning the programs knob to 0, wait for the buzzer to beep and then turn back to your selected program.

Pre Creasecare

When a delayed start has been selected, the clothes are tumbled occasionally during the delayed period to help prevent creases developing.

www.aristonappliances.us

High Heat

When available this button selects high heat. Press this button and a high heat setting is selected and the light next to the button comes on. Timed programs have a default to low heat. If the light alongside the button is on then pressing the button selects a low heat setting and the light goes out.

Alarm

Available on all programs and allows the buzzer to give a signal at the end of the drying cycle, to remind you that the clothes are ready to be removed.

Press the button and the light will show that the option is selected.

Post Creasecare

The clothes are occasionally tumbled after the end of the drying and air fluff cycles to help prevent creases developing should you not be available to remove the load immediately the program is complete.

● Door Opening

Opening the door during a program will stop the dryer and have the following effects:

●All 3 progress lights and the 3hr delay light come on.

●During a delay phase the delay will continue to count down. The start button must be pressed to resume the delay program.

One of the delay lights will flash to show the current delay setting.

●The start button must be pressed to resume the program. The progress lights will change to show the current status.

●During the air fluff or post creasecare phase of a drying program and anytime during an Airing or Air Fluff program, the program will finish. Pressing the start button will re-start a new program at the beginning.

●Changing the programs knob will select a new program, after you press the start button. You can use this to select the Air Fluff program to cool the clothes, if you find them dry enough.

●Note

If you have a power outage, switch off the power or remove the plug, press the START button and the program will resume.

Laundry

Sorting your laundry

●Check symbols on clothing labels to make sure that the articles can be tumble dried.

●Sort laundry by fabric type.

●Empty pockets and check buttons.

●Close zippers and hooks and tie loose belts and strings.

●Wring out each item in order to eliminate as much excess water as possible.

! Do not load dripping wet clothes into the dryer.

Maximum load size

Do not load more than maximum capacity. These numbers refer to dry weight: Natural fibres: 7 kg max (15 lb) Synthetic fibres: 3 kg max (6.6 lb)

! DO NOT overload the dryer as this could result in reduced drying performance.

Typical weights

Clothes

Blouse	Cotton	150 g	5 oz
	Other	100 g	3 oz
Dress	Cotton	500 g	1 lb 2 oz
	Other	350 g	12 oz

Jeans		700 g	1 lb 6 oz

10 Diapers		1000 g	2 lb 3 oz
Shirt	Cotton	300 g	10 oz
	Other	200 g	7 oz
T-Shirt		125 g	4 oz


Household Items
Duvet cover	Cotton	1500 g	3 lb 5 oz
(Double)	Other	1000 g	2 lb 3 oz

Large Tablecloth		700 g	1 lb 6 oz
Small Tablecloth		250 g	9 oz
Tea Towel		100 g	3 oz

Bath Towel		700 g	1 lb 6 oz
Hand Towel		350 g	12 oz
Double Sheet		500 g	1 lb 2 oz
Single Sheet		350 g	12 oz

At the end of a drying cycle, cottons could still be damp if you grouped cottons and permanent press items together. If this happens simply give them an additional short period of drying.

www.aristonappliances.us

Wash Care Labels

Look at the labels on your garments, especially when tumble drying for the first time. The following symbols are the most common:

May be tumble dried

Do not tumble dry

Tumble dry at high heat setting

Tumble dry at low heat setting

What not to tumble dry in your dryer:

●Articles that contain rubber or rubber-like materials or plastic film (pillows, cushions, or PVC rainwear), any other flammable objects or objects that contain flammable substances (towels soiled with hair spray).

●Glass fibres (certain types of draperies).

●Items which have been dry cleaned.

●Items with the ITCL Code (see Special clothing items) . These can be cleaned with special at-home dry cleaning products. Follow instructions

carefully.

●Large bulky items (quilts, sleeping bags, pillows, cushions, large bedspreads etc). These expand when drying and would prevent airflow through the dryer.

Laundry

Special clothing items

Blankets and Bedspreads: acrylic items (Acilan, Courtelle, Orion, Dralon) must be dried with special care on LOW heat setting. Avoid drying for a long period of time.

Pleated or creased garments: read the manufacturer’s drying instructions on the garment.

Starched articles: do not dry these with non-starched items. Make sure that as much of the starch solution is removed from the load as possible before placing it in the dryer. Do not over-dry: the starch will become powdery and leave your clothing limp, which defeats the purpose of starch.

Drying times

The table below presents APPROXIMATE drying times in minutes. Weights refer to dry garments:

Regular Cottons

High (full) Heat

Drying times 800-1000rpm in washing machine

		Half Load				Full Load

2 lb	4 lb	7 lb	9 lb	11 lb	13 lb	15 lb

1 kg	2 kg	3 kg	4 kg	5 kg	6 kg	7 kg

30-40	40-55	55-70	70-80	80-90	95-120120-140

Permanent Press

Low (gentle) Heat

Drying times on reduced spin in washing machine

	Half Load	Full Load

2 lb	4 lb	7 lb

1 kg	2 kg	3 kg

40-50	50-70	70-90

Delicates/Acrylics
Low (gentle) Heat

Drying times on reduced spin in washing machine

	Half Load	Full Load

	2 lb	4 lb
	1 kg	2 kg

40-60		55-75

www.aristonappliances.us

Times are approximate and can vary depending upon:

●Amount of water retained in clothes after spin cycle: towels and delicates retain a lot of water.

●Fabrics: items that are the same type of fabric but different textures and thicknesses may not have the same drying time.

●Quantity of laundry: single items or small loads may take longer to dry.

●Dryness: If you are going to iron some of your clothes, they can be taken out while still a bit damp. Others can be left longer if you need them to be completely dry.

●Heat setting.

●Room temperature: if the room where the dryer is located is cold, it will take longer for the dryer to dry your clothes.

●Bulk: some bulky items can be tumble dried with care. We suggest that you remove these items several times, shake them out, and return them to the dryer until finished.

! Do not over-dry your clothes.

All fabrics contain a little natural moisture, which keeps them soft and fluffy.

Ariston ASL75CXS Care, Use and Installation booklet

Maintenance and Care

When to switch off the electricity

! Unplug your dryer when not using it, when cleaning it and during maintenance activities.

Clean the filter after each cycle

The filter is an important part of your dryer:

it accumulates lint and fluff that is formed while drying. When finished drying, clean the filter by rinsing it under running water or with your vacuum cleaner. Should the filter become clogged up, the airflow inside the dryer will be seriously compromised: drying times lengthen and you will consume more energy. It may also damage your dryer.

The filter is found in front of the dryer trim (see diagram). Removing the filter:

1.Pull the plastic grip of the filter upwards (see diagram).

2.Clean the filter and replace it correctly.

Ensure the filter is fully located flush into the tumble dryer trim.

! Do not use the dryer without replacing the filter.

Check the drum after each cycle

Turn the drum manually in order to remove small items (handkerchiefs) that could have been left behind.

Cleaning the condenser unit

Periodically (every month) remove the condenser unit and clean any build up of fluff from between the plates by rinsing it under the tap with cold water.

This should be done with cold water from the rear of the condenser.

To remove the condenser:

1.Unplug the dryer and open the door.

2.Pull open the condenser cover (see diagram). Release the three catches by turning 90˚ counterclockwise then pull on the grip and remove from the dryer.

3.Clean the surface of the seals and replace, making sure that the catches have been secured.

Cleaning the dryer

●External parts in metal or plastic and rubber parts can be cleaned with a damp cloth.

●Periodically (every 6 months) vacuum the front air intake grille and vents at the rear of the dryer, to remove any build up of fluff, lint or dust. Also to remove accumulation of fluff from the front of the condenser and filter areas, clean occasionally with a vacuum cleaner.

!Do not use solvents or abrasives.

!Your dryer uses special bearing components which do not need lubrication.

!Have your dryer checked regularly by authorized technicians to ensure electrical and mechanical safety.

Cleaning the drum

! Do not use abrasives, steel wool or stainless steel cleaning agents to clean the drum.

A coloured film may start to appear on the stainless steel drum, this may be caused by a combination of water and, or cleaning agents such as fabric conditioner from the wash. This coloured film will not affect the dryer performance.

		Filter
					Tap
					Tap
							Rear


						Front



Condenser cover				Condenser unit
Catches	Handle		Air Intake



www.aristonappliances.us

Troubleshooting

Before you call our Customer Care Department, go through the following troubleshooting suggestions:

Problem:	Possible causes / Solution:
The dryer won’t start.	●	The plug is not plugged into the socket, or not making contact.
	●	There has been a power outage.
	●	The fuse has blown.
	●	The door is not closed securely?
	●	The PROGRAMS knob has not been set properly (see Start and Programs).
	●	The START button has not been pressed (see Start and Programs).

Drying cycle will not begin.

Its taking a long time to dry.

●You have set a delayed time (see Start and Programs).

●The filter has not been cleaned (see Maintenance).

●The temperature setting is not ideal for the type of fabric you are drying (see Start and Programs and see Laundry).

●The condenser needs cleaning (see Maintenance).

●The correct drying time has not been selected for the load (see Laundry).

●The air intake grille or rear vents are obstructed (see Installation and see Maintenance).

●The items were too wet (see Laundry).

●The dryer was overloaded (see Laundry).

Programme finishes and	! For safety the dryer has a maximum program time of 3 hours. If an
clothes are damper than	automatic program has not sensed the required final moisture in this time
expected.	the dryer will complete the program and stop. Check the above points and
	run the program again, if the results are still damp, contact our Customer
	Care Department.
The ON/OFF light flashes to	● Note down the other lights that are on and contact our Customer Care
indicate a fault.	Department.

If you still have a problem call our Customer Care Department on: 1 888 426 0825

Spare Parts

This dryer is a complex machine. Repairing it yourself or having a non-authorized person try to repair it could cause harm to one or more persons and to the machine, and could invalidate the spare parts warranty.

Call an authorized service center if you experience problems while using the machine.

Contact number: 1 888 426 0825

www.aristonappliances.us

Installation Instructions

Read these instructions with care.

These instructions are provided for use by qualified installers, in addition the installation must comply with:

●In the United States, in accordance with the National Electric Code ANSI/NFPA70 - latest edition and any State, Municipal or local codes.

●In Canada, in accordance with the Canadian Electric Code C22.1 - latest edition and any Provincial, Municipal or local codes.

Electrical

The dryer comes with a four-wire power supply cord fitted with a 14-30P (plug), a receptacle should be fitted in a location accessible after the dryer is installed. The four wire dryer wire cord assembly fitted must be used when the appliance is installed in a location where grounding through the neutral is prohibited. Grounding through the neutral is prohibited for; new branch-circuit installations; mobile homes, recreational vehicles and areas were local codes do not allow grounding through the neutral conductor.

If a 10-30R (receptacle) is installed a locally obtained 3 wire dryer cord kit minimum ratings 240V, 30A, 95C and marked for clothes dryers (ring terminals) should be fitted

To fit a 10-30P dryer cord assembly follow the steps below:

1.Make sure the dryer is not plugged into a power outlet.

2.Remove the cover from the cable junction box located on the rear of the dryer.

3.Remove Green link wire from ground terminal.

4.Loosen the nut securing the cable bush, disconnect and discard the existing cable and bush.

5.Fit one end of the Green link to the ground terminal using washer and nut. Position the link wire to the Neutral terminal (N), but do not fit securing screw at this stage.

Green link wire.

6.Follow any instructions provided with the kit and fit the cable using the strain relief supplied with the kit, do not fully tighten the strain relief at this stage.

www.aristonappliances.us

7. Connect the L1, N and L2

wires.

On flat cords the center wire is the Neutral conductor, fit to the terminal marked ‘N’.

On round cords the Green or White conductor should be fitted to the terminal marked ‘N’.

8.Fully tighten the terminal block screws and ground connection nut, position the cord, finally fully tighten the strain relief.

9.Refit the cover to the box.

Grounding

Some local codes may require a separate ground. In such cases the required ground wire, clamp and screw must be purchased separately.

NEVER ground the dryer to plastic plumbing lines, gas lines or water pipes.

NOTE: IF IN DOUBT ABOUT ANY OF THE ABOVE CONSULT A QUALIFIED ELECTRICIAN.

Where to put your dryer

Check local codes before choosing a location. Some codes do not permit installation in a garage, closet, mobile home or bedroom.

DO NOT install the dryer in an area where gasoline or other inflammable materials are kept or stored.

When operating the dryer, there has to be adequate ventilation. Make sure you put the dryer in an environment that is not damp and has proper air circulation throughout. Airflow around the dryer is essential to condense the water produced during washing, the dryer will not operate sufficiently in an enclosed space or cupboard. If installed in a closet we recommend that you leave the door open when the dryer is in use.

! If using the dryer in a small room or cold room some condensation could be experienced.

Minimum installation clearances:

	Closet	Under counter
Sides	3/4" (15mm)	3/4" (15mm)
Top	1/2" (10mm)	1/2" (10mm)
Rear	3/4" (15mm)	3/4" (15mm)
Front	3/4" (15mm)	not applicable

If installed in a closet it must have the following dimensions and have two ventilation openings each having an area 72 sq.ins. (450 sq.cm) located 6" (150mm) from top and bottom of the door. It must NEVER be installed in a closet with a solid door. The dryer has adjustable height feet, use these to level the dryer after fitting into its final position.

Installation Instructions

Water drain

Your dryer needs a drain to discharge the water condensed during the drying process.

Simply fit the hose provided into this drain, if the dryer is stacked onto or installed next to a washing machine it can share the same drain. The drain must be less than 3' (1 m) above the bottom of the dryer.

! Make sure that the hose is not squashed or kinked when the dryer is in its final location.

Door reversal instructions

(only if stacked on top of washing machine).

Door catch

The door of your dryer is reversible and can easily be changed. Exchange diagonally the hinge brackets and blanking plugs. Exchange the door latch and catch with their opposite blanking plates (see above diagram).

www.aristonappliances.us

Stacking kit

The dryer is provided with a stacking kit, which allows the dryer to be fitted to the top of an Ariston washing machine:

Model AW125NA

Model AW129NA

Model AW149NA

The kit contains all the necessary brackets and screws. Tools needed:

No.2 Philips Screwdriver 2mm drill, power or hand drill

SAFETY

For personal safety, DO NOT try to fit the dryer on top of the washing machine on your own. A second person should help to lift the tumble dryer onto the washing machine and to relocate the stacked washer and dryer.

1.You will need to get to the sides of the washing machine to fit the stacking kit and dryer. If necessary pull the machine away from its location to gain access to the machine to fit the stacking kit and dryer.

2.Follow the instructions provided with the stacking kit.

+ 28 hidden pages