APW Wyott LOWERATOR CUP DISPENSERS, DROP-IN PAPER CUP Service Manual

R

INSTALLATION

AND

OPERATING

INSTRUCTIONS

LOWERATOR CUP DISPENSERS

DROP-IN PAPER CUP

DROP-IN PLASTIC CUP

DROP-IN STYROFOAM CUP

RETAIN THIS MANUAL FOR FUTURE REFERENCE

IMPORTANT FOR FUTURE REFERENCE

Please complete this information and retain this manual for the life of the equipment. For Warranty Service and/or Parts, this information is required.

Model Number

Serial Number

Date Purchased

This equipment has been engineered to provide you with year-round dependable service when used according to the instructions in this manual and standard commercial kitchen practices.

		P/N 88822/88823/88981 9/05
Phone:	[phone]
Fax:	[phone]	APW WYOTT
Toll Free: [phone]
Website: www.apwwyott.com		P.O. Box 1829
E-mail:	[e-mail]	Cheyenne, WY 82003

1

	STYROFOAM CUP DISPENSERS	1
	Assembly	2
	1. Make sure all parts are included with your	3
	shipment:
	Tube with spring and spring cover (1)
	Rubber gasket (1 )	4
	Dispenser head (1)	5
	1/4-20 x 3/8" screws (3)
	Acorn nuts (3)

2.Place the tube so the flange with 3 holes is

upward, and remove the tape.

6

3. Place the rubber gasket on the top surface.

4.Place the dispenser head on the gasket, so

the head flange is downward.		7

5.Insert the screws from the bottom and tighten the acorn nuts onto the screws from the top, as shown.

PARTS LIST (STYROFOAM CUP DISPENSERS)

		Item 1	Item 2	Item 3	Item 4	Item 5	Item 6	Item 7
	Final Assembly Number	Acorn Nut	Dispenser	Rubber	Spring Cover	Spring	Screw, Slot Hd	Tube
		1/4 - 20	Head	Gasket			1/4 - 20 x 3/8"
	300324, 2 9/16"	84272	210316	210326	210315	89012	82014	210311
	300325. 2 3/4"	84272	210317	210327	210315	89012	82014	210311
	300326, 2 7/8"	84272	210318	210328	210315	89012	82014	210311
	300327,3" .	84272	210319	210329	210315	89012	82014	210311
	300328, 3 1/8	84272	210320	210330	210315	89012	82014	210311
	300329,33/8"	84272	210321	210331	210315	89012	82014	210311
	300330,3 1/2"	84272	210322	210332	210315	89012	82014	210311
	300331,39/16"	84272	210323	210333	210315	89012	82014	210311
	300332,35/8"	84272	210324	210334	210315	89012	82014	210311
	300333, 3 3/4"	84272	210325	210335	210315	89012	82014	210311
	300338, 32 oz. (Plaslc)	84272	216139	216143	216138	89504	82014	216144
	300339, 32 oz. (Styrofoam)	84272	216139	216143	216138	89505	82014	216144
	211237, Small	84272	211241	211236	210315	211233	82014	211254
	211256, 19 & Med	84272	211249	210330	211244	89030	82014	211234

2

PAPER CUP DISPENSERS

Assembly andAdjustment

1. Make sure all parts are included with your shipment:

Tube with spring and spring cover (1)

Rubber gasket (1)

Dispenser Head (1)

1/4-20 X 3/8" screws (3)Acorn nuts (3)

2. Place the tube so the flange with 3 holes is upward, and remove the tape.

3.Twist the 0 Ring on to one, two or three studs, depending on the cup size. See Size Adjustment Diagram.

4. Assemble the remaining parts according to the exploded view.

To adjust this dispenser to the desired cup size:

1.Remove acorn nuts from top of dispenser, and remove dispenser head.

2.Twist rubber band on (1), (2), or (3) studs for desired tightness (see FiguresA, B and C.)

3.Replace head (be sure rubber band is outside of bushings, and replace acorn nuts.

SIZE ADJUSTMENT DIAGRAMS

1

2

3

4

5

7

6

8

	FIGURE “A”	FIGURE “B”	FIGURE “C”
ITEM	QUANTITY	DESCRIPTION		PART NUMBER
1	3	Acorn Nut, ¼ -20		84272
2	1	Dispenser Head		210336
3	1	Rubber “O” Ring		21402
4	1	Spring Cover		210315
5	3	Spacer		54231
6	3	Truss Head Screw, ¼ -20 Slotted		82052
7	1	Spring		89030
8	1	Tube		210311

3