Apple POWER MAC G4 FW 800, POWER MAC G4 MIRRORED DRIVE DOORS Power Supply Replacement Instructions
Page 1
Power Mac G4
Power Supply
Replacement Instructions
Follow the instructions in this sheet carefully. Failure to follow these instructions could
damage your equipment and void its warranty.
Note:
Written and video instructions covering customer-installable parts are available at
http://www.info.apple.com/installparts/.
Warning: During this procedure, keep small parts away from children.
Tools Required
The following tools are required for this procedure:
• #2 Phillips screwdriver
• small flat-blade screwdriver
• T-10 Torx driver
Opening the Computer
Warning: Always shut down your computer before opening it to avoid damaging its
internal components or causing injury. After you shut down the computer, the
internal components can be very hot. Let the computer cool down before
continuing.
1. Place your computer on a clean, flat surface.
2. If you think your computer is in sleep, press the power button on the front of the
computer to wake it.
3. Shut down your computer and wait five minutes before continuing.
4. If you attached a security cable through the computer’s lockable cover latch, remove
the cable.
5. Unplug all other cables from the computer except the power cord.
073-0723 Rev. B
Page 2
6. Touch the metal PCI access covers on the back of the computer.
(Figure 1)
Important:
port access covers before you touch any parts or install any components inside the
computer. To avoid static electricity building back up in your body, do not walk
around the room until you have completed the installation and closed the computer.
Figure 1
To avoid electrostatic discharge, always ground yourself by touching the
7. Unplug the power cord.
Warning: The power supply in your computer is a high-voltage component and
should not be opened for any reason, even when the computer is off. If the
power supply needs service, contact your Apple reseller or Apple Authorized
Service Provider.
8. Lift the latch on the right side access panel.
9. Gently lower the access panel until it lies flat. To avoid scratching the case, lower the
panel onto a soft, clean cloth.
Warning: If you see any lights glowing on the main logic board, the computer has
not been shut down. Close the side access panel and shut down the computer
before proceeding.
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
2
Page 3
Removing the Installed Power Supply
1. Remove the two screws that secure the optical drive carrier to the chassis.
Figure 2
2. Slide the back panel off the carrier.
(Figure 3)
(Figure 2)
Figure 3
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
3
Page 4
3. Slide the carrier back and rotate it so that you can reach the drive cables.
4. Disconnect the drive data and power cables (P6 and P7) from the back of the optical
drive(s) and remove the carrier from the computer.
Figure 4
(Figure 4)
5. Disconnect the ribbon cable from the logic board and fold it back to expose the lower
fan cable connector.
Figure 5
(Figure 5)
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
4
Page 5
6. Using a small flat-blade screwdriver, gently lift up the locking tab on the lower fan
cable and disconnect the cable from the logic board.
Figure 6
(Figure 6)
7. Slide the fan straight up to disconnect it from the optical drive shelf, and remove the
fan from the computer.
Figure 7
(Figure 7)
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
5
Page 6
8. Use a T-10 Torx driver to remove the power supply screw.
Figure 8
(Figure 8)
9. Remove the Phillips screw from the side panel.
Figure 9
(Figure 9)
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
6
Page 7
10. Disconnect the power supply cables from all drives and from the logic board.
11.
Note:
For the Power Mac G4 (FW 800) model of the computer, press and hold the
tab on the black, plastic connector cover as you pull up the power connector from the
board.
(Figure 10)
Replacement Note:
replacement power supply.
Figure 10
12. Release the power cable harness from the guides and route the harness out through
the opening in the optical drive shelf.
Install the connector cover over the power connector for the
(Figure 11)
Figure 11
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
7
Page 8
13. Slide the power supply forw ard and remove the power supply and cable harness from
the computer.
Figure 12
(Figure 12)
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
8
Page 9
Installing the Replacement Power Supply
1. Install the replacement power supply.
Replacement Note:
• connectors P4 and P5 are routed inside the front drive carrier
• connectors P2 and P3 are routed so they can reach drives in the back drive carrier
(Figure 13)
Figure 13
When rerouting the cable harness, make sure
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
9
Page 10
2. Reinstall the fan.
Replacement Note:
straight down until you feel the fan lock into place.
Figure 14
Align the fan with the three latches in the drive shelf and slide
(Figure 14)
Replacement Note:
narrower flex cable, as shown.
Figure 15
Route the fan cable under the ribbon cable and over the
(Figure 15)
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
10
Page 11
3. Reinstall the optical drive carrier.
Replacement Note:
sure the power cable bundle at the side panel are routed in the recessed channel.
(Figure 16)
Figure 16
Before sliding the carrier back onto the optical drive shelf, make
Replacement Note:
sure the latch on the underside of the carrier engages with the notch in the drive
shelf.
(Figure 17)
Figure 17
When sliding the carrier back onto the optical drive shelf, make
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
11
Page 12
Replacement Note:
the top lip of the panel engages with the top edge of the drive carrier.
Before sliding the rear panel back onto the carrier, make sure
Warning:
(Figure 18)
Figure 18
Be careful not to pinch the power cable between the panel and the carrier.
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
12
Page 13
Closing the Computer
1. Raise the side access panel, lift the latch, and press the panel against the case until it
snaps securely into place.
2. Reconnect all cables and restart your computer.
Warning: Never turn on your computer unless all of its internal and external
parts are in place and it is closed. Operating the computer when it is open or
missing parts can damage your computer or cause injury.
Apple Computer, Inc.
© 2003 Apple Computer, Inc. All rights reserved.
Under the copyright laws, this document ma y not be copied, in whole or in part, without the
written consent of Apple.
The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other
countries. Use of the “keyboard” Apple logo (Option-Shift-K) for commercial purposes
without the prior written consent of Apple may constitute trademark infringement and
unfair competition in violation of federal and state laws.
Every effort has been made to ensure that the information in this document is accurate.
Apple is not responsible for printing or clerical errors.
Apple Computer, Inc.
1 Infinite Loop
Cupertino, CA 95014-2084
USA
+ 1 408 996 1010
http://www.apple.com
Apple, the Apple logo, Mac, Macintosh, and the Mac logo are trademarks of Apple
Computer, Inc., registered in the U.S. and other countries.
Power Mac is a trademark of Apple Computer, Inc.
Power Mac G4 (Mirrored Drive Doors/FW 800) Power Supply -
13
Loading...