Installation and Operation
Rack Power Distribution Unit
AP9572
AP9551
AP9567
AP9568
Publication Date: September 2015
990-1917B-001
Schneider Electric Legal Disclaimer
The information presented in this manual is not
warranted by Schneider Electric to be authoritative,
error free, or complete. This publication is not meant
to be a substitute for a detailed operational and site
specific development plan. Therefore, Schneider
Electric assumes no liability for damages, violations of
codes, improper installation, system failures, or any
other problems that could arise based on the use of
this Publication.
The information contained in this Publication is
provided as is and has been prepared solely for the
purpose of evaluating data center design and
construction. This Publication has been compiled in
good faith by Schneider Electric. However, no
representation is made or warranty given, either
express or implied, as to the completeness or
accuracy of the information this Publication contains.
IN NO EVENT SHALL SCHNEIDER ELECTRIC, OR
ANY PARENT, AFFILIATE OR SUBSIDIARY
COMPANY OF SCHNEIDER ELECTRIC OR THEIR
RESPECTIVE OFFICERS, DIRECTORS, OR
EMPLOYEES BE LIABLE FOR ANY DIRECT,
INDIRECT, CONSEQUENTIAL, PUNITIVE,
SPECIAL, OR INCIDENTAL DAMAGES
(INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF BUSINESS, CONTRACT,
REVENUE, DATA, INFORMATION, OR BUSINESS
INTERRUPTION) RESULTING FROM, ARISING
OUT, OR IN CONNECTION WITH THE USE OF, OR
INABILITY TO USE THIS PUBLICATION OR THE
CONTENT, EVEN IF SCHNEIDER ELECTRIC HAS
BEEN EXPRESSLY ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. SCHNEIDER
ELECTRIC RESERVES THE RIGHT TO MAKE
CHANGES OR UPDATES WITH RESPECT TO OR
IN THE CONTENT OF THE PUBLICATION OR THE
FORMAT THEREOF AT ANY TIME WITHOUT
NOTICE.
Copyright, intellectual, and all other proprietary rights
in the content (including but not limited to software,
audio, video, text, and photographs) rests with
Schneider Electric or its licensors. All rights in the
content not expressly granted herein are reserved. No
rights of any kind are licensed or assigned or shall
otherwise pass to persons accessing this information.
This Publication shall not be for resale in whole or in
part.
Contents
General Information............................. 1
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Safety and grounding information . . . . . . . . 1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Receiving . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Material recycling . . . . . . . . . . . . . . . . . . . . . . 2
Installation............................................ 3
Install the Rack PDU . . . . . . . . . . . . . . . . . . . . .3
Mounting options . . . . . . . . . . . . . . . . . . . . . . 3
Toolless mounting . . . . . . . . . . . . . . . . . . . . . 3
Bracket mounting . . . . . . . . . . . . . . . . . . . . . . 4
Operation.............................................. 5
AP9572 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
AP9551 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
AP9567 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
AP9568 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Specifications....................................... 6
Life Support Policy . . . . . . . . . . . . . . . . . . . . . .8
General policy . . . . . . . . . . . . . . . . . . . . . . . . 8
Examples of life-support devices . . . . . . . . . 8
Factory Warranty.................................. 9
Terms of warranty . . . . . . . . . . . . . . . . . . . . . 9
Non-transferable warranty . . . . . . . . . . . . . . 9
Exclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Warranty claims . . . . . . . . . . . . . . . . . . . . . . 10
Basic Rack Power Distribution Unit
i
General Information
Safety
Safety and grounding information
Read the following information before installing or
operating your APC by Schneider Electric Rack
Power Distribution Unit (PDU).
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR
ARC FLASH
• This PDU is intended for indoor use only.
• Do not install this PDU where excessive moisture or
heat is present.
• Never install any wiring, equipment, or PDUs during a
lightning storm.
• Plug this PDU into a three-wire, grounded power outlet
only. The power outlet must be connected to
appropriate branch circuit/mains protection (fuse or
circuit breaker). Connection to any other type of power
outlet may result in a shock hazard.
• Use only the supplied brackets for mounting, and use
only the supplied hardware to attach the mounting
brackets.
• Do not use extension cords or adapters with this PDU.
• If a socket-outlet is not accessible to the equipment, a
socket-outlet shall be installed.
• Do not work alone under hazardous conditions.
• Check that the power cord, plug, and socket are in
good condition.
• Disconnect the PDU from the power outlet before you
install or connect equipment to reduce the risk of
electric shock when you cannot verify grounding.
Reconnect the PDU to the power outlet only after you
make all connections.
• Use a protective earth connector with equipment. This
type of connector carries the leakage current from the
load devices (computer equipment). Do not exceed a
total leakage current of 3.5 mA.
• Do not handle any kind of metallic connector before the
power has been removed.
• Use one hand, whenever possible, to connect or
disconnect signal cables to avoid a possible shock
from touching two surfaces with different grounds.
• This unit does not have any user-serviceable parts.
Repairs are to be performed only by factory-trained
service personnel.
Failure to follow these instructions will result in
death or serious injury.
Always install the equipment as shown in the
Installation Manual.
Rack Power Distribution Unit
1
Overview
Receiving
Inspect the package and contents for shipping
damage. Make sure all parts were sent.
Immediately report any shipping damage to the
shipping agent. Report missing contents, product
damage, or other problems with the product to
APC by Schneider Electric or your APC by
Schneider Electric reseller.
Inventory
Item Quantity
Basic Rack PDU 1
Vertical-mounting brackets (870-8473) 2
8-32 flat-head screws 8
Material recycling
The shipping materials are recyclable.
Please save them for later use, or
dispose of them appropriately.
2
Rack Power Distribution Unit
Installation
Install the Rack PDU
Mounting options
Y ou can inst all the Environmental Ma nager Main
Module in one of two ways: using toolless
mounting pegs (provided) or the verticalmounting brackets (provided).
• To install the Environmental Manager Main
Module using the toolless mounting method,
install it in the rear of the NetShelter
Enclosure, in the cable channel directly
behind the rear vertical-mounting rails.
• To install the Environmental Manager Main
Module using the mounting brackets, install
it on a vertical-mounting rail in the rack or
enclosure.
Toolless mounting
Note: In order to mount the Rack PDU using
the toolless mounting option, you must install it
in a NetShelter VX Enclosure.
®
VX
1. Slide both mounting pegs into the holes
located in the cable channel in the rear
panel of the enclosure.
2. Snap the Rack PDU into place by pushing
it downward until it locks into position.
Note: You can mount two Rack PDUs on one
side of the enclosure by using the toolless
mounting method.
Rack Power Distribution Unit
3
Bracket mounting
To mount the Rack PDU vertically in a
NetShelter
or any standard EIA-310-D rack or
enclosure:
1. Attach the vertical-mounting brackets to
the Rack PDU, using four 8-32 flat-head
screws per bracket.
Note:
Use only the supplied screws.
2. Attach the Rack PDU to a vertical
mounting rail in the rear of the enclosure
using two additional screws per bracke t
(not provided).
4
Rack Power Distribution Unit
Operation
AP9572
0U, 16A, 208/230V Basic Rack PDU
15 IEC-320-C13 outlets.
2.5 m (8.2ft) IEC-320-C19 to IEC-320-C20
power cord.
AP9551
0U, 20A, 120V Basic Rack PDU.
NOTE: When the button is raised, the circuit
breaker has tripped. Unplug at least one piece of
equipment.
pdu0318a
One 20 amp circuit breaker
14 NEMA 5-15R outlets
3.66 m (12 ft) NEMA L5-20P power cord
AP9567
0U, 15 A, 100/120 V Basic Rack PDU
One 15 amp circuit breaker
14 NEMA 5-15 outlets
3.66 m (12 ft) NEMA 5-15 power cord
AP9568
0U, 10 A, 120 V, (15) C-13 Basic Rack PDU
15 IEC-320-C13 outlets
1.98 m (6.5 ft) power cord with IEC-320-C14
plug
Rack Power Distribution Unit
5
Specifications
AP9572 AP9551
Electrical
Input
voltage
range
Maximum
current draw
120 – 230 VAC 120 VAC +/- 10%
20 A
(16A derated)
20 A
(16A derated)
Physical
Size
(h×w×d)
Shipping
dimensions
(h×w×d)
Weight 2.00 kg (4.40 lb) 2.20 kg (4.82 lb)
Shipping
weight
62.00 × 4.44 ×
4.44 cm
(24.40 × 1.75 ×
1.75in)
63.81×16.82×14.
60 cm
(25.13×6.63×5.75
in)
3.64 kg (8.00 lb) 2.92 kg (6.40 lb)
610 x 42 x 44 mm
(24.00 x 1.67 x
1.75 in)
648 x 178 x 152
mm
(25.50 x 7.00 x
6.00 in)
Environmental
Elevation
(above
MSL)
Relative
humidity
Operating: 0–3000 m
(0–10,000 ft)
Storage: 0–15 000 m
(0–50,000 ft)
Operating: 0 to 95%,
non-condensing
Storage: 0 to 95%,
non-condensing
Temperature Operating: –5 to 45°C
(23 to 113°F)
Storage: –25 to 65° C
(–13 to 149° F)
Compliance
Safety UL/cUL Listed, CE,
VDE,
AS/NZS 60950-1
cUL Listed, CE,
GOST,
Queensland
Australia, UL
Listed, VDE
6
Rack Power Distribution Unit
Electrical
AP9567 AP9568
Input voltage
range
Maximum
current draw
100/120 VAC 120/240 VAC
15 A
(12A derated)
10 A
Physical
Size
(h×w×d)
Shipping
dimensions
(h×w×d)
Weight 2.18 kg (4.80 lb) 2.0 kg (4.40 lb)
Shipping
weight
61.00 × 4.44 ×
4.44 cm
(24.00 × 1.76 ×
1.76in)
64.80× 17.80×
15.20 cm
(25.50× 7.00 ×
6.00in)
2.92 kg (6.40 lb) 2.73 kg (6.00 lb)
61.00 x 4.40 x
4.40 cm
(24.00 x 1.67 x
1.75 in)
648 x 178 x
152 mm
(25.50 x 7.00 x
6.00 in)
Environmental
Elevation
(above MSL)
Relative
humidity
Temperature Operating: –5 to 45°C
Operating: 0–3000 m
(0–10,000 ft)
Storage: 0–15 000 m
(0–50,000 ft)
Operating: 0 to 95%,
non-condensing
Storage: 0 to 95%,
non-condensing
(23 to 113°F)
Storage: –25 to 65° C
(–13 to 149° F)
Compliance
Safety cUL Listed, METI
Denan, UL Listed
cUL Listed, CE,
GOST,
Queensland
Australia, UL
Listed, VDE
Rack Power Distribution Unit
7
Life Support Policy
General policy
APC by Schneider Electric does not recommend
the use of any of its products in the following
situations:
• In life-support applications where failure or
malfunction of the APC by Schneider Electric
product can be reasonably expected to
cause failure of the life-support device or to
affect significantly its safety or effectiveness.
• In direct patient care.
APC by Schneider Electric will not knowingly sell
its products for use in such applications un less it
receives in writing assurances satisfactory to
APC by Schneider Electric that (a) the risks of
injury or damage have been minimized, (b) the
customer assumes all such risks, and (c) the
liability of APC by Schneider Electric is
adequately protected under the circumstances.
Examples of life-support devices
The term life-support device includes but is not
limited to neonatal oxygen analyzers, nerve
stimulators (whether used for anesthesia, pain
relief, or other purposes), autotransfusion
devices, blood pumps, defibrillators, arrhythmia
detectors and alarms, pacemakers,
hemodialysis systems, peritoneal dialysis
systems, neonatal ventilator incubators,
ventilators (for adults and infants), anesthesia
ventilators, infusion pumps, and any other
devices designated as “critical” by the U.S. FDA.
Hospital-grade wiring devices and leakage
current protection may be ordered as options on
many APC by Schneider Electric UPS systems.
APC by Schneider Electric does not claim that
units with these modifications are certified or
listed as hospital-grade by APC by Schneider
Electric or any other organization. Therefore
these units do not meet the requirement s for use
in direct patient care
8
Rack Power Distribution Unit
Factory Warranty
This warranty applies only to the products you
purchase for your use in accordance with this
manual.
Terms of warranty
APC by Schneider Electric warrants its products
to be free from defects in materials and
workmanship for a period of two years from the
date of purchase. APC by Schneider Electric will
repair or replace defective products covered by
this warranty. This warranty does not apply to
equipment that has been damaged by accident,
negligence or misapplication or has been
altered or modified in any way. Repair or
replacement of a defective product or part
thereof does not extend the original warranty
period. Any parts furnished under this warranty
may be new or factory-remanufactured.
Non-transferable warranty
This warranty extends only to the original
purchaser who must have properly registered
the product. The product may be registered at
the APC by Schneider Electric Web site,
www.apc.com.
Exclusions
APC by Schneider Electric shall not be liable
under the warranty if its testing and examination
disclose that the alleged defect in the product
does not exist or was caused by end user’s or
any third person’s misuse, negligence, improper
installation or testing. Further, APC by
Schneider Electric shall not be liable under the
warranty for unauthorized attempts to repair or
modify wrong or inadequate electrical volt age or
connection, inappropriate on-site operation
conditions, corrosive atmosphere, repair,
installation, exposure to the elements, Acts of
God, fire, theft, or installation contrary to APC by
Schneider Electric recommendations or
specifications or in any event if the APC by
Schneider Electric serial number has been
altered, defaced, or removed, or any other
cause beyond the range of the intended use.
THERE ARE NO WARRANTIES, EXPRESS
OR IMPLIED, BY OPERATION OF LAW OR
OTHERWISE, OF PRODUCTS SOLD,
SERVICED OR FURNISHED UNDER THIS
AGREEMENT OR IN CONNECTION
HEREWITH. APC BY SCHNEIDER ELECTRIC
DISCLAIMS ALL IMPLIED WARRANTIES OF
MERCHANTABILITY, SATISFACTION AND
FITNESS FOR A PARTICULAR PURPOSE.
APC BY SCHNEIDER ELECTRIC EXPRESS
WARRANTIES WILL NOT BE ENLARGED,
DIMINISHED, OR AFFECTED BY AND NO
OBLIGATION OR LIABILITY WILL ARISE
Rack Power Distribution Unit
9
OUT OF, APC BY SCHNEIDER ELECTRIC
RENDERING OF TECHNICAL OR OTHER
ADVICE OR SERVICE IN CONNECTION WITH
THE PRODUCTS. THE FOREGOING
WARRANTIES AND REMEDIES ARE
EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES AND REMEDIES. THE
WARRANTIES SET FORTH ABOVE
CONSTITUTE APC BY SCHNEIDER
ELECTRIC’S SOLE LIABILITY AND
PURCHASER’S EXCLUSIVE REMEDY FOR
ANY BREACH OF SUCH WARRANTIES. APC
WARRANTIES EXTEND ONLY TO
PURCHASER AND ARE NOT EXTENDED TO
ANY THIRD PARTIES.
IN NO EVENT SHALL APC BY SCHNEIDER
ELECTRIC, ITS OFFICERS, DIRECTORS,
AFFILIATES OR EMPLOYEES BE LIABLE
FOR ANY FORM OF INDIRECT, SPECIAL,
CONSEQUENTIAL OR PUNITIVE DAMAGES,
ARISING OUT OF THE USE, SERVICE OR
INSTALLATION, OF THE PRODUCTS,
WHETHER SUCH DAMAGES ARISE IN
CONTRACT OR TORT, IRRESPECTIVE OF
FAULT, NEGLIGENCE OR STRICT LIABILITY
OR WHETHER APC BY SCHNEIDER
ELECTRIC HAS BEEN ADVISED IN
ADVANCE OF THE POSSIBILITY OF SUCH
DAMAGES. SPECIFICALLY, APC BY
SCHNEIDER ELECTRIC IS NOT LIABLE FOR
ANY COSTS, SUCH AS LOST PROFITS OR
REVENUE, LOSS OF EQUIPMENT, LOSS OF
USE OF EQUIPMENT, LOSS OF SOFTWARE,
LOSS OF DA TA, COSTS OF SUBSTITUENTS,
CLAIMS BY THIRD PARTIES, OR
OTHERWISE.
NO SALESMAN, EMPLOYEE OR AGENT OF
APC BY SCHNEIDER ELECTRIC IS
AUTHORIZED TO ADD TO OR VARY THE
TERMS OF THIS WARRANTY. WARRANTY
TERMS MAY BE MODIFIED, IF AT ALL, ONLY
IN WRITING SIGNED BY AN APC BY
SCHNEIDER ELECTRIC OFFICER AND
LEGAL DEPARTMENT.
Warranty claims
Customers with warranty claims issues may
access the APC by Schneider Electric customer
support network through the Support page of the
APC by Schneider Electric Web site,
www.apc.com/support. Select your country
from the country selection pull-down menu at
the top of the Web page. Select the Support tab
to obtain contact information for customer
support in your region.
10
Rack Power Distribution Unit
Worldwide Customer
Support
Customer support for this product is available at no
charge at www.apc.com.
© 2015 Schneider Electric. APC, the APC logo, and
NetShelter are owned by Schneider Electric Industries S.A.S.
All other trademarks are property of their respective owners.
990-1917B-001
9/2015
Loading...