Rack Power Distribution Unit—AP9565
Description
Mounting brackets
APC’s AP9565 is a 16-amp Rack Power Distribution Unit (PDU) that
provides 100- to 240-volt power to rack-mounted equipment.
IEC 320 C20 power inlet
12 IEC 320 C13 outlets
IEC 320 C19 to IEC 320 C20 power cord
Note
Brackets for horizontal mounting
Brackets for vertical mounting
Each PDU is packaged with two different sets of mounting
brackets (for horizontal and vertical mounting). Choose your
mounting orientation and attach the appropriate brackets to the
PDU.
Safety and Grounding
C
Read the following information before installing or operating your APC
Rack Power Distribution Unit (PDU):
• This PDU is intended for indoor use only.
• Do not install this PDU where excessive moisture or heat is
present.
• Never install any wiring, equipment, or PDUs during a lightning
storm.
• Plug this PDU into a three-wire, grounded power outlet only. The
power outlet must be connected to appropriate branch circuit/
mains protection (fuse or circuit breaker). Connection to any other
type of power outlet may result in a shock hazard.
• Use only the supplied brackets for mounting.
• Do not work alone under hazardous conditions.
• Check that the power cord, plug, and socket are in good condition.
• Disconnect the PDU from the power outlet before you install or
connect equipment to reduce the risk of electric shock when you
cannot verify grounding. Reconnect the PDU to the power outlet
only after you make all connections.
• Use a protective earth connector with equipment. This type of
connector carries the leakage current from the load devices
(computer equipment). Do not exceed a total leakage current of
3.5 mA.
aution
Risk of electrical shock. Use only the supplied hardware to
attach the mounting brackets.
2 Rack Power Distribution Unit — AP9565
Installation
Horizontal mounting
To mount the Rack PDU horizontally in any standard 19-inch EIA-310
rack or enclosure:
1. Attach the horizontal-mounting brackets to the PDU.
2. Install the PDU using hardware included with your rack or
enclosure. The PDU will occupy one U-space.
Rack Power Distribution Unit — AP9565 3
Installation
Vertical mounting
To mount the Rack PDU vertically in any standard EIA-310 rack or
enclosure:
1. Attach the vertical-mounting brackets to the PDU.
2. Install the PDU on a vertical mounting rail in your rack or
enclosure.
4 Rack Power Distribution Unit — AP9565
Specifications
AP9565
Electrical
Nominal input voltage 100–240 V
Input frequency 50/60 Hz
Input connector IEC 320 C20 inlet
Output connectors 12 IEC 320 C13 outlets
16 A @ 100 – 240 V (UL)
Maximum total current draw
12 A @ 100–240 V (cUL)
16 A @ 220 – 240 V (VDE)
Physical
Size [h×w×d]
Shipping size [h×w×d]
Weight 4.5 lb (2.0 kg)
Shipping weight 8.0 lb (3.6 kg)
1.75 ×17.60 ×2.25 in
(4.45× 44.70 ×5.72 cm)
2.75 ×18.25×9.00 in
(7.00× 46.35 ×22.86 cm)
Environmental
Elevation (above MSL)
Operating
Storage
Temperature
Operating
Storage
Humidity
Operating
Storage
0–10 000 ft (0–3000 m)
0–50 000 ft (0–15 000 m)
0 to 45° C (32 to 115° F)
–25 to 65° C (–13 to 149° F)
0–95%
0–95%
RH Non-condensing
RH Non-condensing
Approvals
Safety verification UL, cUL , VDE, CE
Rack Power Distribution Unit — AP9565 5
Warranty and Service
Limited warranty
Warranty limitations
APC warrants the PDU to be free from defects in materials and
workmanship for a period of two years from the date of purchase. Its
obligation under this warranty is limited to repairing or replacing, at its
own sole option, any such defective products. This warranty does not
apply to equipment that has been damaged by accident, negligence, or
misapplication or has been altered or modified in any way. This
warranty applies only to the original purchaser.
Except as provided herein, APC makes no warranties, express or
implied, including warranties of merchantability and fitness for a
particular purpose. Some jurisdictions do not permit limitation or
exclusion of implied warranties; therefore, the aforesaid limitation(s) or
exclusion(s) may not apply to the purchaser.
Except as provided above, in no event will APC be liable for direct,
indirect, special, incidental, or consequential damages arising out of
the use of this product, even if advised of the possibility of such
damage.
Specifically, APC is not liable for any costs, such as lost profits or
revenue, loss of equipment, loss of use of equipment, loss of software,
loss of data, costs of substitutes, claims by third parties, or otherwise.
This warranty gives you specific legal rights and you may also have
other rights, which vary according to jurisdiction.
Obtaining service
To obtain support for problems with your PDU:
0
1. Note the serial number and date of purchase. The serial number is
located on the bottom of the PDU.
2. Contact Customer Support at a phone number located on the back
cover of this manual. A technician will try to help you solve the
problem by phone.
3. If you must return the product, the technician will give you a return
material authorization (RMA) number. If the warranty expired, you
will be charged for repair or replacement.
4. Pack the unit carefully. The warranty does not cover damage
sustained in transit. Enclose a letter with your name, address, RMA
number and daytime phone number; a copy of the sales receipt;
and a check as payment, if applicable.
5. Mark the RMA number clearly on the outside of the shipping
carton.
6. Ship by insured, prepaid carrier to the address provided by the
Customer Support technician.
6 Rack Power Distribution Unit — AP9565
Life-Support Policy
General policy
Examples of life-support devices
American Power Conversion (APC) does not recommend the use of any
of its products in the following situations:
• In life-support applications where failure or malfunction of the
APC product can be reasonably expected to cause failure of the
life-support device or to affect significantly its safety or
effectiveness.
• In direct patient care.
APC will not knowingly sell its products for use in such applications
unless it receives in writing assurances satisfactory to APC that (a) the
risks of injury or damage have been minimized, (b) the customer
assumes all such risks, and (c) the liability of American Power
Conversion is adequately protected under the circumstances.
The term life-support device includes but is not limited to neonatal
oxygen analyzers, nerve stimulators (whether used for anesthesia, pain
relief, or other purposes), autotransfusion devices, blood pumps,
defibrillators, arrhythmia detectors and alarms, pacemakers,
hemodialysis systems, peritoneal dialysis systems, neonatal ventilator
incubators, ventilators (for adults and infants), anesthesia ventilators,
infusion pumps, and any other devices designated as “critical” by the
U.S. FDA.
Hospital-grade wiring devices and leakage current protection may be
ordered as options on many APC UPS systems. APC does not claim that
units with these modifications are certified or listed as hospital-grade by
APC or any other organization. Therefore these units do not meet the
requirements for use in direct patient care.
Rack Power Distribution Unit — AP9565 7
APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of the following ways:
• Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer support
requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which provides customer support
information.
– www.apc.com/support/
Global support searching APC Knowledge Base and using e-support.
• Contact an APC Customer Support center by telephone or e-mail.
– Regional centers:
Direct InfraStruXure Customer Support
Line
APC headquarters U.S., Canada (1)(800)800-4272 (toll free)
Latin America (1)(401)789-5735 (USA)
Europe, Middle East, Africa
Japan (0) 35434-2021
Australia, New Zealand, South Pacific
area
– Local, country-specific centers: go to www.apc.com/support/contact for contact information.
Contact the
how to obtain local customer support.
APC representative or other distributor from whom you purchased your APC product for information on
Entire contents copyright © 2004 American Power Conversion. All rights reserved.
Reproduction in whole or in part without permission is prohibited. APC, the APC logo,
InfraStruXure, and NetShelter are trademarks of American Power Conversion Corporation and
may be registered in some jurisdictions. All other trademarks, product names, and corporate
names are the property of their respective owners and are used for informational purposes only.
(1)(877)537-0607 (toll free)
(353)(91)702000 (Ireland)
(61) (2) 9955 9366 (Australia)
990-1536B-001 02/2004
*990-1536B-001*
Loading...