Anthem MRX 710, MRX 510, MRX 310 User Manual

MRX 710 / 510 / 310

Audio/Video Receiver

OPERATING MANUAL

Anthem, AnthemLogic, ARC, and Paradigm are trademarks or registered trademarks of Paradigm Electronics Inc. © Paradigm Electronics Inc.

We reserve the right to change speciﬁcations and/or features without notice as design improvements are incorporated.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872; 7,333,929;

7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks, & DTS-HD, DTS-HD Master

This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation.

Reverse engineering and disassembly are prohibited.

HDMI, the HDMI logo and High-Deﬁnition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

All other trademarks are the property of their respective owners.

MRX 710 / 510 / 310

Audio/Video Receiver

OPERATING MANUAL

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning ﬂash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the point where

they exit from the apparatus.

11. Only use the attachments/accessories speciﬁed by the manufacturer.

12. Use only with a cart, stand, tripod, bracket or table speciﬁed by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such

as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: To reduce the risk of ﬁre or electric shock, do not expose this apparatus to rain or

moisture. Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place:

• Burning objects (i.e. candles), as they may cause ﬁre, damage to this unit, and/or

personal injury.

• Containers with liquid in them, as they may fall and liquid may cause electrical shock to

the user and/or damage to this unit.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with liquids, such as vases, shall be placed on the apparatus.

Do not install this equipment in a conﬁned space such as a case or similar. Install it away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.

Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause ﬁre, damage to this unit, and/or personal injury.

Install this unit near the AC outlet and where the AC power plug can be reached easily.

This unit is not disconnected from the AC power source when it is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

NOTE: This product is not an auto voltage Receiver. Connect only to the prescribed AC outlet,

i.e., 120V 60Hz or 220-240V 50Hz.

CAUTION: These servicing instructions are for use by qualiﬁed service personnel only. To reduce

the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualiﬁed to do so.

CAUTION: Changes or modiﬁcations to this equipment not expressly approved by Paradigm

Electronics for compliance could void the user’s authority to operate this equipment.

FCC WARNING: Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

DO NOT LOCATE IN THE FOLLOWING PLACES:

To ensure long-lasting use, do not locate the unit:

• Exposed to direct sunlight.

• Near sources of heat such as heaters.

Left 0.2 m (8 in) or more

• Highly humid or poorly ventilated.

• Dusty.

• Subjected to mechanical vibrations.

• On wobbly, inclined, or otherwise unstable surfaces.

• Near windows where there is a chance of exposure

to rain, etc.

• On top of an ampliﬁer or other component which

dissipates a great deal of heat.

To ensure proper heat radiation, ensure clearance from walls and other equipment according to diagram.

IMPORTANT INFORMATION FOR UK CUSTOMERS: DO NOT cut off the mains

plug from this equipment. If the plug ﬁtted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. If, nonetheless, the mains plug is cut off, REMOVE THE FUSE and dispose of the PLUG immediately, to avoid possible shock hazard by inadvertent connection to the mains supply. If this product is not provided with a mains plug, or one has to be ﬁtted, then follow the instructions given below:

IMPORTANT: DO NOT make any connection to the larger terminal which is marked with the letter “E” or by the safety earth symbol or colored GREEN or GREEN AND YELLOW.

The wires in the mains lead on this product are colored in accordance with the following code:

BLUE – NEUTRAL BROWN – LIVE

As these colors may not correspond with the colored markings identifying the terminals in your plug, proceed as follows:

The BLUE wire must be connected to the terminal marked with the letter “N” or colored BLACK. The BROWN wire must be connected to the terminal marked with the letter “L” or colored RED.

When replacing the fuse, only a correctly rated and approved type should be used, and be sure to re-ﬁt the fuse cover. If in doubt consult a competent electrician.

Above 0.2 m

(8 in) or more

Behind 0.2 m (8 in) or more

Right 0.2 m

(8 in) or more

MRX 710

ZONE 2 MAIN

iii

NOTES ON ENVIRONMENTAL PROTECTION

At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s manual and packaging, point this out. The materials can be reused in accordance with their markings. Through re-use, recycling of raw materials or other forms of recycling of old products, you are making an important contribution to the protection of our environment. Your local administrative ofﬁce can advise you of the responsible waste disposal point.

INFORMATION ABOUT COLLECTION AND DISPOSAL OF WASTE BATTERIES (DIRECTIVE 2006/66/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF EUROPEAN UNION) (for European customers only)

Batteries bearing any of these symbols indicate that they should be treated as “separate collection” and not as municipal waste. It is encouraged that necessary measures are implemented to maximize the separate collection of waste batteries and to minimize the disposal of batteries as mixed municipal waste. End-users are exhorted not to dispose waste batteries as unsorted municipal waste. In order to achieve a high level of recycling waste batteries, discard waste batteries separately and properly through an accessible collection point in your vicinity. For more information about collection and recycling of waste batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

By ensuring compliance and conformance to proper disposal of waste batteries, potential hazardous effects on human health is prevented and the negative impact of batteries and waste batteries on the environment is minimized, thus contributing to the protection, preservation and quality improvement of the environment.

CdHgPb

Anthem and any related party assume no liability for the user’s failure to comply with any requirements.

TABLE OF CONTENTS

INTRODUCTION

1 1.1 Before Making Connections

1 1.2 In-Use Notices

2 1.3 Front Panel

3 1.4 Rear Panel MRX 710

4 1.5 Rear Panel MRX 310

5 1.6 Remote Control

6 1.7 Speaker Positioning

CONNECTIONS

6 2.1 Video Connections

7 2.2 Audio Connections

10 2.3 Antennas

10 2.4 Local Area Network

10 2.5 12 Volt Trigger

10 2.6 Infra Red

10 2.7 Power

SETUP

13 3.1 HDMI Output Conﬁguration

14 3.2 Speaker Setup

16 3.3 Bass Managment

17 3.4 Listener Position

18 3.5 Level Calibration

19 3.6 Input Setup

23 3.7 Volumes / Rec Output

24 3.8 Network / Remote Control

27 3.9 Display

28 3.10 General Conﬁguration

30 3.11 Save / Load Settings

31 3.12 System Information

ANTHEM ROOM CORRECTION

33 4.1 Before Starting

33 4.2 ARC Software Installation

34 4.3 Microphone Stand Assembly

34 4.4 Microphone Positioning

34 4.5 Measurement

35 4.6 Manual Mode and Targets

36 4.7 Advanced Subwoofer Targets

37 4.8 Printing A Report

37 4.9 Updating ARC

OPERATION

38 5.1 Power On / Off and Volume

38 5.2 Zone 2 Operation

39 5.3 Input Selection

39 5.4 Tuner

40 5.5 Level Trim

41 5.6 Bass / Treble / Balance

41 5.7 Lip-Sync

41 5.8 Listening Modes

42 5.9 Dolby Volume and Dynamic Range Control

42 5.10 Display Brightness

42 5.11 Info Display

43 SPECIFICATIONS

44 LIMITED WARRANTY

45 THE BIG PICTURE: FRONT PANEL (MRX 710)

46 THE BIG PICTURE: REAR PANEL (MRX 710)

47 THE BIG PICTURE: REAR PANEL (MRX 310)

INTRODUCTION

Thank you for purchasing the Anthem MRX series receiver.

The MRX 710, MRX 510, and MRX 310 receivers are cutting-edge home theater audio components with HDMI switching, video scaling and upconversion, state of the art room equalization, second zone capabilities, and FM/AM tuner.

Anthem products are engineered to recreate the passion of live performance and thrill of the best movie theaters by using the highest level of circuit design, proprietary software, superior build quality, innovative features, and intuitive ergonomics with tremendous ﬂexibility.

1.1 BEFORE MAKING CONNECTIONS

Check that you have received all items listed below and report discrepancies to your dealer as soon as possible. In case the unit needs to be transported in the future, keep the packing materials. Retain the invoice that you received from your authorized Anthem dealer at time of purchase – without it, service will not be provided under warranty.

• MRX Receiver

• Remote control

• FM antenna

• AM loop antenna

• 2 AAA batteries

• USB extension cable

• IEC power cord (US / EU / CN types are supplied by factory, other types are normally provided by the local distributor)

Additional items in Anthem Room Correction kit (ARC-1M):

• USB Microphone

• Microphone clip

• Telescopic stand with boom

• USB cable

• CAT5 cable

• CD containing microphone calibration le and software installer

1.2 IN-USE NOTICES

• Disconnect the power cord before connecting or disconnecting any components.

• If the receiver was transported or stored in the cold, let it reach room temperature before use.

• Due to continuing advances, operational characteristics may change. If this manual contains discrepancies please check www.anthemAV.com for the latest manual or software.

1.3 FRONT PANEL

MRX 710 shown, others are similar. For a larger diagram see inside back cover.

1 2

1 – Navigation buttons

2 – Display

3 – Volume, level functions, and character selection

4 – Power / standby

5 – Input selection

6 – Zone 2 selection

7 – Level selection

8 – Remote control sensor location

9 – Mode selection

10 – Display brightness

11 – Setup menu selection

12 – HDMI jack (MRX 710/510), headphone jack (behind cover)

11 5

910

MRX 710

ZONE 2MAIN

4678

1.4 REAR PANEL MRX 710

MRX 710 US model shown. EU model, CN model, and MRX 510 are similar.

1 – FM/AM antenna connections

2 – HDMI inputs (HDMI1 accepts up to 4K resolution)

3 – HDMI outputs with Audio Return Channel

4 – AC input

5 – Local area network connection for IP control and Anthem Room Correction

6 – USB jack for software updates

7 – Component video inputs

8 – Composite video input

9 – Coaxial and optical digital audio inputs

10 – Speaker connections

11 – Coaxial and optical digital audio outputs

12 – Zone 2 audio outputs

13 – Record audio outputs

14 – RS-232 interface (bidirectional) for serial control

15 – Analog audio L/R inputs

16 – Main pre-out connections

17 – Trigger output

18 – IR input and output

19 – Chassis ground screw

1213141516

910

4 5

678

1.5 REAR PANEL MRX 310

US model shown. EU and CN models are similar.

1 – FM/AM antenna connections

2 – HDMI inputs (HDMI1 accepts up to 4K resolution)

3 – HDMI outputs with Audio Return Channel

4 – AC input

5 – Local area network connection for IP control and Anthem Room Correction

6 – USB jack for software updates

7 – Component video inputs

8 – Composite video input

9 – Coaxial and optical digital audio inputs

10 – Speaker connections

11 – Coaxial and optical digital audio outputs

12 – Zone 2 audio outputs

13 – Record audio outputs

14 – RS-232 interface (bidirectional) for serial control

15 – Analog audio L/R inputs

16 – Main pre-out connections

17 – Trigger output

18 – IR input and output

19 – Chassis ground screw

1213141516

910

4 5

678

1.6 REMOTE CONTROL

1 – Main zone power on and standby

2 – Bass, Treble, Balance, Channel Level, Front panel dimmer

3 – Numeric keypad for tuner presets

4 – Input list

5 – Tuner preset

6 – Setup menu

7 – Info and status

8 – Navigation controls

9 – Clear for deleting input conﬁgurations and tuner presets, and clearing new entry

10 – Dolby Volume and Dolby Digital Dynamics

11 – Listening mode

12 – Volume

13 – Last menu entry

14 – Mute

15 – Next/previous tuner preset, setup menu page up/down

16 – Lip-sync

17 – Backlight

18 – Zone 2 controls

The left/right buttons also select previous/next input.

The up/down buttons also control tuner station.

BASS

TREB

BALDIM

LEVEL

SETUP

SELECT

INPUTPRESET

CLEAR

VOL

DYN

LIP-SYNC

MODE

LAST

PG/PR

VOL

ZONE 2

RC-MRX 2

INPUT

1.7 SPEAKER POSITIONING

The illustrations below show typical 5.1 and 7.1-channel speaker placement.

Bass response highly depends on room acoustics and experimentation with subwoofer placement is recommended. Anthem Room Correction can help with placement.

5.1

Channel

7.1

Channel

CONNECTIONS

This section describes connections between system components. Conﬁguration of input and output will be discussed later, in section 3.

2.1 VIDEO CONNECTIONS

HDMI

With this type of connection, video and audio are carried together digitally. Maximum video resolution is 4K (also known as UHD and 2160p) at 30 frames per second for HDMI outputs and HDMI input 1, and 1080p at 60 frames per second for the rest of the HDMI inputs. Connect HDMI output from MRX to a display with HDMI input – one with High-bandwidth Digital Content Protection (HDCP) is required to display copy-protected material. If you are using a 4K source component, connect it to HDMI input 1. All HDMI connections support 3D.

Be careful when connecting HDMI cables. The connector should easily slide in the jack – do not insert it on an angle and do not force it. Each connector contains 19 delicate pins and damaged pins can damage jacks. Such damage is not covered by warranty. If your HDMI cables have been connected enough times that they are about to wear out, new cables are recommended.

Use only High Speed cables and connecting devices. Connecting devices that may have worked in an older setup do not necessarily work with Deep Color or 4K. If there is trouble producing an image and the source allows Deep Color to be disabled, start troubleshooting by turning it off. 12-bit Deep Color that works at 1080p24 may not work at 1080p50 or 1080p60 if cable bandwidth is not adequate for the higher frame rate.

If you are using adapters or port savers, start troubleshooting by eliminating them. Use of these devices is generally not recommended.

COMPONENT VIDEO

Component video uses three coaxial cables and normally has a maximum resolution of 1080i, or 480p when the source is copy-protected with Macrovision.

COMPOSITE VIDEO

This traditional standard-denition format combines the black/white and color information for transmission on a single coaxial cable.

2.2 AUDIO CONNECTIONS

AUDIO INPUTS AND OUTPUTS

Digital audio sources can be connected with a coaxial, optical, or HDMI cable. These carry 2-channel PCM, Dolby Digital, and DTS. The HDMI inputs also accept up to eight channels of PCM, Dolby Digital TrueHD, DTS-HD, and DTS-HD Master Audio.

Audio on the HDMI outputs is 2-channel PCM as this is meant for the TV’s use.

HDMI AUDIO RETURN CHANNEL

This is meant for use when the TV is the audio source. An example is internet streaming accessed through the TV’s user interface. As long as the TV also has Audio Return Channel (check its manual) it sends audio from the TV to the receiver through the HDMI connection that sends video from the receiver to the TV, eliminating the need for a separate audio connection. CEC control, described in a later section, must be enabled for Audio Return Channel to function.

DIALOG NORMALIZATION

Dolby Digital program material contains non-audio data which the receiver uses to adjust playback level, when necessary, so volume variations between movies and programs are eliminated. Without Dialog Normalization, movies not encoded at standardized levels for the dialog could lose dynamic range – higher levels can result in distorted peaks, lower levels can result in quiet sounds disappearing into the noise oor.

If the display reads “Dial Norm Offset -4.0 dB” at the start of a movie, it is indicating that the encoded level is higher than standard by 4.0 dB – the playback level of all channels is then automatically reduced by 4 dB.

PREAMP OUTPUTS

The pre-outs are variable according to the volume control and can be used with external amplication.

ZONE 2 AND REC

Zone 2 and REC may use analog input, or the optical/coaxial inputs as long as the source is 2-channel PCM.

If HDMI audio from a Dolby Digital, DTS, or 2-channel PCM source is problematic or takes too long to switch, use of coax/ optical audio connection is recommended (HDMI video can still be used). Older cable and satellite receivers often benet from this.

The coax and optical REC outputs provide a passthrough of coax/optical input, or 2-channel PCM, depending on source format.

SPEAKERS

Connect using speaker wire. US models also allow banana plugs.

MRX 710 and MRX 510: If you are only using 5.1 speakers in the main zone, the two

remaining amp channels may be congured for use in Zone 2, or to bi-amp front L/R in the main zone.

Connect the positive (+) connection on the speaker to the positive (+) binding post on the appropriate amplier output, and the negative (–) connection on the speaker to the negative (–) binding post on the same receiver channel using cable that is insulated to handle the maximum output of the receiver. Carefully remove insulation using a wire stripper.

If using speaker cables with banana connectors, rst turn the binding post until it is closed. This way, the plug can be fully inserted.

Do not connect more than one speaker to each amplier output. Be sure that power is turned off when connecting or disconnecting anything and that the speakers are rated for use with this receiver.

–

+ 42 hidden pages