查询EVAL-ADF411XEB1供应商查询EVAL-ADF411XEB1供应商
Evaluation Board For PLL Frequency
a
FEATURES
General Purpose PLL Evaluation Board excluding Synthe-
sizer, VCO, Loop Filter for generating generic PLL standards.
Compatible with ADF4110 and ADF4116 synthesizer fami-
lies.
Accompanying Software allows complete control of syn-
thesizer functions from PC
Battery Operated: Choice of 3V or 5V supplies
BLOCK DIAGRAM
Synthesizer
EV AL-ADF411XEB1
GENERAL DESCRIPTION
This board is designed to allow the user to evaluate
the performance of the ADF411X Frequency Synthesizer for PLL's (Phase Locked Loops). The block
diagram of the board is shown below. It contains the
footprint for a ADF411X synthesizer, a pc connector,
SMA connector for the reference input, power supplies and RF output. There is also a footprint for a
loop filter and a VCO on board. A cable is included
with the board to connect to a pc printer port.
The package also contains windows software to allow
easy programming of the synthesizer.
RF
V
V
DD
VCO
OUT
VCO 1
(Vari-L)
VCO 190-XXXT
SMA
Socket
EVAL-ADF411XEB1
PC CONNECTOR
9V BATTERY
POWER SWITCH
ON OFF
ADF411X
TCXO
Vectron
AD7706
V
P
CE
REF
IN
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties which may result from its use.
No license is granted by implication or otherwise under any patent or patent rights of
Analog Devices.
REV.PrB
© Analog Devices, Inc., 1999
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781-329-4700 Fax: 781-326-8703
04/00
Hardware Description
The evaluation board comes with a cable for connecting to
the printer port of a PC. The silk screen and cable diagram for
the evaluation board are shown below. The board schematic is
shown on pages 3 and 4.
EV AL-ADF411XEB1
EVAL-ADF411X
EVAL-ADF421X
1
6
2
7
3
8
4
9
5
9 Way
Female D-Type
To
ADF411X
ADF421X
Evaluation
Board
Brown - DATA
Figure 2. PC Cable Diagram
voltage is too low to sustain the required 3V or 5V for the
board supply.
Loop component values shown in the circuit diagram are
for 900MHz RF output, 5mA CP current, VCO190902T, 200kHz channel spacing and 20kHz loop bandwidth.
Black - CLK
Red - LE
Orange - CE
White - GND
Yellow
Purple
1
2
3
4
5
6
7
8
9
10
Blue
11
12
13
25 Way Male
D-Type
To
PC Printer Port
14
15
16
17
18
19
20
21
22
23
24
25
PC
Figure 1. Evaluation Board Silkscreen
The board is powered from a single 9V battery. The
power supply ciruitry allows the user to choose either 3V
or 5V for the ADF4113 V
supply. The default settings are 3V for the ADF411X V
and VP, and for the VCO
DD
DD
and 5V for the ADF411X VP and for the VCO supply. It
is very important to note that the ADF4113 V
never exceed the ADF411X V
. This can damage the de-
P
should
DD
vice.
All components necessary for LO generation are catered
for on-board. The TCXO connector provides the necessary Reference Input. The PLL is made up of the
ADF411X, passive loop filter and the VCO 190-XXXT
from Vari-L. The output is available at RFOUT through
a standard SMA connector. If the user wishes they may
use their own power supplies and reference input. In this
case, they need to insert SMA connectors to as shown on
the silkscreen and block diagram.
The AD7706 A/D converter is used to monitor the power
supply voltage and current consumption of the ADF411X.
This helps the user pick the optimum synthesizer settings for
power consumption and also provides an alert if the battery
–2–
REV.PrB
04/00
EV AL-ADF411XEB1
Figure 3. Evaluation Board Circuit Diagram (Page 1)
–3–
REV.PrB
04/00
EV AL-ADF411XEB1
Figure 4. Evaluation Board Circuit Diagram (Page 2)
–4–
REV.PrB
04/00
Software Description
The software comes on a CD. If the user double clicks on
“setup.exe”, then the install wizard installs the software.
Follow the on-screen directions. The software will be
installed in a default directory called “C:/Program Files/
ADF4XXX/ADF4XXX_rev0”. To run the software,
simply double-click on “adf4XXX_rev0.exe”.
Before the main software screen appears, the Device window appears, which will ask the user to choose which device is being evaluated. Choose the device being evaluated
and click OK.
The Main Interface window will now appear. (See Figure
5)
Click on Choose Port, and the Port Connector window
will appear. Choose the port that the cable is connected to
on the PC and click OK. (Normally LPT1)
Click on Reference Frequency, and the Reference Frequency window will appear. Enter the reference frequency
being used and click OK.
EV AL-ADF411XEB1
Click on RF VCO Output Frequency, and the Output
Frequency window will appear. Enter the output frequency
and PFD reference frequency, and click OK.
Click On Prescaler, and the Prescaler window will appear.
Grab the pointer, and choose the desired prescaler value.
Click OK.
Click on Charge Pump Current Setting 2 or Charge
Pump Current Setting 1 and the Current Setting window
will appear. Grab the pointer to set the Charge Pump
Current Setting. Click OK.
Click on the RF PD Polarity button to set the RF PD
Polarity bit.
The data is now set up, and other features can now be examined by the user.
Figure 5. Software Front Panel
–5–
REV.PrB
04/00
EV AL-ADF411XEB1
Table 1. Bill of Materials for the EVAL-ADF411XEB1
Qty Reference Designator Description Manufacturer PCB DECAL VALUE
1 U1 Do Not Inser ADI TSSOP-16
1 U2 AD7706BR ADI SO16WB AD7706BR
1 U3 AD780AR ADI SO8NB AD780AR
1 U4 ADP3300ART-5 ADI SOT23-6 ADP3300ART-5
1 U5 ADP3300ART-3 ADI SOT23-6 ADP3300ART-3
1 VCO1 Do Not Inser Vari-L
1 Y1 4.9152MHz Crystal
1Y2 10 MHz TCXO
1 D1 SD103C Schottky Diode General Semiconductor DO35 SD103C
1 D2 IN4001 D035 FEC 365-117
1 D3 Red Low Power LED Vishay LED FEC 657-130
1 D4 Green Low Power LED (Do Not Insert) Vishay LED F EC 657-141
2 C1 C41 0.1uF Multi Layer Ceramic Capacitor Murata Case 0603 FEC 499-675
1 C2 10uF 6.3V Tantalum Capacitor AVX CAP\TAJ_B FEC 197-014
4 C3 C26 C27 C28 100pF Multi Layer Ceramic Capacitor Murata Case 0603 FEC 499-122
2 C4 C31 22uF 6.3V Tantalum Capacitor AVX CAP\TAJ_A FEC 197-038
3 C5 C7 C11 0.1uF Multi Layer Ceramic Capacitor Murata Case 0805 FEC 317-627
5 C6 C8 C9 C12 C32 10pF Multi Layer Ceramic Capacito Murata Case 0 603 FEC 499-110
2 C13 C14 1nF Multi Layer Ceramic Capacitor Murata Case 0603 FEC 317-202
2 C21 C22 33pF Multi Layer Ceramic Capacito Murata Case 0603 FEC 498-555
1 C23 Do Not Inser Case 0805
1 C24 Do Not Inser Case 0805
1 C25 Do Not Inser Case 0805
3 C33 C36 C40 10nF Multi Layer Ceramic Capacito Murata Case 0603 FEC 499-146
2 C34 C37 1uF 16V Tantalum Capacitor AVX CAP\TAJ_A FEC 498-701
2 C35 C38 4.7uF 10V Tantalum Capacitor AVX CAP\TAJ_A FEC 498-658
2 C39 C42 10uF 6.3V Tantalum Capacitor AVX CAP\TAJ_A FEC 197-014
Vectron International
Vectron International
HC49 low profile VXA1-1011
T-1185
1 R1 20r 5% Resistor (Surface Mount) Multicomp Case 0805 FEC 771-132
7 R2 R5 R6 R7 R8 R9 R10 330r 1% Resistor (Surface Mount) Multicomp Case 0603 FEC 911-143
1 R3 3k3 1% Resistor (Surface Mount) Multicomp Case 0603 FEC 911-290
1 R4 4k7 1% Resistor (Surface Mount) Multicomp Case 0603 FEC 911-318
1 R11 Do Not Inser Case 0603
1 R18 1M 1% Resistor (Surface Mount) Multicom p Case 0603 FEC 911-598
1 R19 Do Not Inser Case 0805
1 R20 Do Not Inser Case 0805
3 R21 R22 R23 18r 1% Resistor (Surface Mount) M ulticomp Case 0603 FEC 911-021
1 R24 51r 1% Resistor (Surface Mount) M ulticomp Case 0603
1 R25 Do Not Inser Case 0805
3 R27 R28 R29 10k 1% Resistor (Surface Mount) M ulticomp Case 0603 FEC 911-355
6 R30 R31 R32 R33 R40 R41 100k 0.1% Resistor (Surface Mount) Meggitt Case 0603 FEC 911-471
2 R36 R37 330K 1% Resistor (Surface Mount) Multicomp Case 0603 FEC 911-537
2 R38 R39 0r 1% Resistor (Surface Mount Multicomp Case 0603 FEC 772-227
1 R12 0r 1% Resistor - Do Not Insert Multicomp Case 0603 FEC 772-227
1 R42 4k7 1% Resistor (Surface Mount) M ulticomp Case 0805 FEC 911-938
1 SW1 Push Button Switch Omron SW\PB-SMALL FEC 176-986
1 SW2 SPDT Switch - (Washable) Apem SW_SIP-3P FEC 150-559
18 T1-15 T 19-21 Red Testpoint W Hughes TESTPOINT FEC-240-345
1 J1 9 PIN D-TYPE MALE (HORIZ) McMurdo DCON9M FEC 150-750
5 J2 J3 J4 J5 J6 Do Not Inser SMA
1J7
4 LK1 LK2 LK4 LK5 3 pin header Harwin SIP-3P FEC 512-047
1 LK3 2 pin header Harwin SIP-2P FEC 512-035
5 LK1-5 Shorting Shunt Harwin FEC 150-410
2 P1 Pair PCB snap-on battery connector Keystone BATT _PP3 FEC 723-988
1 P1 9V PP3 Battery Duracell FEC 908-526
GO LD 50 Ω SMA SOCKET
Pasternack SMA PE4118
4 Each Corner Rubber Stick-On Feet 3M FEC 148-922
1 EVAL-ADF411XEB1 PCB ADI
Parts Free issued by ADI.
Leave position blank - Do not insert.
–6–
REV.PrB
04/00
Loading...