American Standard 606B.X01, 606B.X05 Installation Manual

SELECTRONIC

®

PROXIMITY CONCEALED URINAL
FLUSH VALVE

1.0, 0.5 & 0.125 GPF

MODEL NUMBERS

606B.X10 606B.X01 606B.X05

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components

Certied to comply with ASME A112.19.2

© 2017 AS America, Inc.

will void the warranty.

Installation Instructions

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com
or e-mail us at: [e-mail]

For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / [phone] (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093)

© 2017 AS America Inc.

1

M965643 Rev. 1.8 (11/17)

Thank you for selecting American-Standard...the benchmark of ne quality for over 100 years. To ensure that your
installation proceeds smoothly--please read these instructions carefully before you begin.

UNPACKING

Remove the Flush Valve items from the carton. The illustration below shows all items after they have been
removed from the carton. Some items may be packaged partially assembled to other items.

1. Installation Instructions

2. Flush Valve Body Assembly

3. Cover Plate with Sensor

4. Wall Box

5. Sweat Adapter

6. Stop Valve

7. Manual Override Hoses

LARGE PLATE CONCEALED TOILET FLUSH VALVES

4

Some Residual Water May Remain In The Valve During Shipping.

8a. Vacuum Breaker Flush Connection

(Top Spud)

8b. Vacuum Breaker Flush Connection

(Back Spud)

9. Safety Chain

POWER KITS — SOLD SEPARATELY

DO NOT REMOVE PROTECTIVE
FILM FROM SENSOR
EYE UNTIL INSTALLATION
IS COMPLETE.

3

SELECTRONIC™
PROXIMITY CONCEALED
URINAL FLUSH VALVE

1.0, 0.5 & 0.125 GPF

MODEL NUMBERS

606B.X10 606B.X05 606B.X01

PWRX

Power Kit

Plug-In AC

Power Kit

PK00. PACPK00.WRK

Hard-Wired AC

Power Kit

PK00.HAC

1

9

CAUTION: Use only American Standard

All American Standard Products Are Water Tested At Our Factory.

(In Toronto Area only: 1-905-3061093)

(In Toronto Area only: 1-905-3061093)

(In Toronto Area only: 1-905-3061093)(In Toronto Area only: 1-905-3061093)

supplied cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any
components will void the warranty.

7

6

Certified to comply with ASME A112.19.2M

© 2016 AS America, Inc.

Installation Instructions

NOTE TO INSTALLER: Please give this manual to the customer after installation.

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com

To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com
or e-mail us at: [e-mail]

or e-mail us at: [e-mail]

For Parts, Service, Warranty or other Assistance,

For Parts, Service, Warranty or other Assistance,

[phone] (In Canada: 1-800-387-0369)

please call

please call [phone] (In Canada: 1-800-387-0369)

5

2

VACUUM BREAKER FLUSH CONNECTIONS

606X.4XX 606X.5XX

8a 8b

Multi-AC

Power Kit

PK00.MAC

CR-P2 Battery

Power Kit

2

M965643 Rev. 1.8 (11/17)

Fig. 1 Roughing-in Dimensions

404 mm
(15-7/8")

SENSOR

OVERRIDE
BUTTON

280 mm

(11 ")

389 mm x 265 mm

(15-5/16" X 10-3/8")

ROUGH OPENING FOR BOX

25 mm (1") MAX.

WALL THICKNESS

FINISHED WALL

15˚

15˚

DETECTION ZONE
400 mm-800 mm
(Factory Setting: 400 mm)

GENERAL DESCRIPTION:

SELECTRONIC® PROXIMITY URINAL
FLUSH VALVE

Concealed Flushometer for 3/4"
Spud Fixtures

CAUTION: Use only American Standard
supplied transformers and cable sets.
Using non-AS supplied cables, or cutting,
splicing or modifying any components will
void the warranty.

SUPPLY

SUPPLY
(3/4) NPT.

(3/4") NPT.

-C-L-

-C-L-

108 mm-134 mm

*

*

-C-L-

152 mm

") MIN.

(6

(4-1/4" TO 5-1/4")

TOP OF
FIXTURE

(1-1/4

32 mm

") DIA.

*Note: The Critical Line (-C-L-) on Vacuum
Breaker must typically be 6

above fixture. Consult Codes for details.

" (152mm) min.

RECOMMENDED TOOLS; Fig. 2.

1. Teon Tape

2. Flat Blade Screwdriver

3. Adjustable Wrench

4. Tape Measure

5. Hacksaw

6. Tubing Cutter

7. File

8. For Sweat Connection; Solder and Torch

9. 2.5mm Hex Wrench

10. 1.5mm Hex Wrench

203 mm MAX.

(8") MAX.

Fig. 2

TOP SPUD
FIXTURES

176mm MAX.

") MAX.

(6-15/16

63 mm
(2-1/2") DIA.

120 mm MAX.

(4-3/4") MAX.

TOP OF
FIXTURE

FOR LOCATION OF INLET SUPPLY
ON BACK INLET FIXTURES AND CORRECT
HEIGHT FROM FINISHED FLOOR,
REFER TO FIXTURE INSTRUCTION SHEET.

1

2

10'

4

5

7 9 10

BACK SPUD

FIXTURES

203 mm MAX.

(8

") MAX.

6

3

(6-15/16") MAX.

TOP OF
FIXTURE

32 mm

(1-1/4") DIA.

176 mm MAX.

*

*

152 mm

(6") MIN.

8

-C-L-

PRIOR TO INSTALLATION

Note: Prior to installing the Selectronic™Flush

Valve the following items must be installed.

1. Urinal

2. Drain line

3. Water supply line

IMPORTANT:

• All plumbing and electrical wiring should be
installed in accordance with applicable codes
and regulations.

• The use of water hammer arrestors is strongly
recommended for commercial applications. All piping

behind the walls should be properly secured and
fastened.

• Wate r supply lines must be sized to provide an

adequate volume of water for each xture.

• Flush all water lines prior to operation (see Step 3).
Dirt and debris can cause ush valve to run continuously.

• With the exception of Stop Valve Inlet, DO NOT

use pipe sealant or plumbing grease on any
valve component or coupling!

• Protect the chrome or special nish on the Flushometer.

DO NOT USE toothed tools on nished surfaces to install
or service these valves. Also see “Care and Cleaning”
section of this manual.

• This product contains mechanical and/or electrical

components that are subject to normal wear. These
components should be checked on a regular basis and
replaced as needed to maintain the valve’s performance.

3

M965643 Rev. 1.8 (11/17)

FLUSH VALVE INSTALLATION

INSTALL ELECTRICAL BOX; Fig. 3

1

1. Frame out a 389mm x 265mm (15-5/4" X 10-3/8") rough

opening in wall for the WALL BOX (1) at the dimension
shown.

2. Fasten one end of the SAFETY CHAIN (2) and CLIP
(4) to the WALL BOX (1) with NUT & SCREW (3) provided.

3. Install the WALL BOX (1) into rough opening in the wall

Level and secure the WALL BOX (1) to the wall opening
with screws.

Important: Front face of WALL BOX (1) should be ush
with nished wall.

4. Cut a 2” hole for outlet pipe to xture at dimension shown.*

Fig. 3 (TOP SPUD FIXTURE ILLUSTRATED)

265mm

(10-3/8")

176mm MAX.

(6-15/16) MAX.

120mm MAX.

(4-3/4) MAX.

389mm

(15-5/16")

1

ROUGH OPENING IN WALL

LEVEL

4

*FOR HOLE LOCATION OF
SUPPLY ON BACK INLET
FIXTURES, REFER TO FIXTURE
BEING INSTALLED FOR CORRECT
HEIGHT FROM FINISHED FLOOR

3

2

2

INSTALL SWEAT ADAPTER; Fig. 4

CAUTION

Turn water supplies off before
beginning

Note: Stop Valve inlet is 3/4" NPT. For optional sweat
connection, install Sweat Adapter (1) (Supplied) for 3/4"
copper pipe supply line.

1. Clean the end of the supply pipe. Push the threaded

SWEAT ADAPTER (1) until it is seated against the
internal stop. Sweat the ADAPTER (1) to the pipe.

2. Install the STOP VALVE (2) to the water supply line
with the outlet positioned as required (Behind the Wall).

3. Support piping as required.

3

FLUSH OUT SUPPLY LINES; Fig. 5

1. Open STOP VALVE (1).

2. Tur n on water supply to ush line of any debris or

sediment.

3. Close STOP VALVE (1) and turn off water supply line.

Fig. 4

Fig. 5

115mm-134mm

(4-1/2 TO 5-1/4)

STOP VALVE OUTLET

COUNTER-CLOCKWISE

OPENS STOP VALVE

1

FILE

EDGES

2

STOP VALVE
(3/4"NPT)

CLEAN & SOLDER
TO ADAPTER (1)

CLOCKWISE CLOSES
STOP VALVE

1

4

M965643 Rev. 1.8 (11/17)