American Standard 606B2XX Installation Manual

SELECTRONIC

CONCEALED TOILET FLUSH VALVE

1.1. 1.28 & 1.6 GPF

MODEL NUMBERS

606B2XX

Concealed Back SpudExposed Back Spud Top Spud

CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components

Certied to comply with ASME A112.19.2

will void the warranty.

Installation Instructions

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance, please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369) (In Toronto Area only: 1-905-306-1093)

M965640 Rev. 1.4 (11/17)

Thank you for selecting American-Standard...the benchmark of ne quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

UNPACKING

Remove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton. Some items may be packaged partially assembled to other items.

1. Installation Instructions

2. Flush Valve Body Assembly

3. Cover Plate with Sensor

4. Electrical Box

5. Sweat Adapter

6. Stop Valve

7. Manual Override Hoses

Some Residual Water May Remain In The Valve During Shipping.

8a. Vacuum Breaker Flush Connection

(Exposed Back Spud)

8b. Vacuum Breaker Flush Connection

(Concealed Back Spud)

8c. Vacuum Breaker Flush Connection

(Top Soud)

POWER KITS — SOLD SEPARATELY

All American Standard Products Are Water Tested At Our Factory.

TOP

DO NOT REMOVE PROTECTIVE FILM FROM SENSOR EYE UNTIL INSTALLATION IS COMPLETE.

SELECTRONIC™CONCEALED TOILET FLUSH VALVE

1.28 & 1.6 GPF

MODEL NUMBERS

606B.2XX

PWRX

Power Kit

Plug-In AC

Power Kit

PK00. PACPK00.WRK

Hard-Wired AC

Power Kit

PK00.HAC

VACUUM BREAKER FLUSH CONNECTIONS

606X.2X1

606X.2X2

Certied to comply with ASME A112.19.2

Concealed Back SpudExposed Back Spud Top Spud

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.

(In Toronto Area only: 1-905-306-1093)

8c8b8a

Multi-AC

Power Kit

CR-P2 Battery

Power Kit

Installation Instructions

NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

606X.2X3

PK00.MAC

M965640 Rev. 1.4 (11/17)

Fig. 1

Roughing-in Dimensions

160mm

(6-1/4)

160mm

(6-1/4)

SUPPLY (1) NPT

-C-L- -C-L-

108mm-134mm

*-C-L-

152mm MIN.

(6) MIN.

(4-1/4 TO 5-1/4)

OVERRIDE BUTTON

SENSOR

TOP OF FIXTURE

127mm X 127mm (5X5 CUTOUT FOR BOX)

51mm

(2)

400mm MAX. (15-3/4) MAX.

25mm (1) MAX.

WALL THICKNESS

FINISHED WALL

TOP SPUD

TOILET

70mm (2-3/4) DIA.

128mm MAX.

(5) MAX.

DETECTION ZONE 400mm-800mm (Factory Setting: 400mm)

15˚

360mm MAX.

(14-3/16) MAX.

EXPOSED BACK

SPUD TOILET

GENERAL DESCRIPTION:

SELECTRONIC® PROXIMITY TOILET FLUSH VALVE

Concealed Flushometer for 1-1/2" Top Spud Fixtures

CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.

FOR LOCATION OF INLET SUPPLY ON BACK INLET

FIXTURES AND CORRECT HEIGHT FROM FINISHED FLOOR,

REFER TO FIXTURE INSTRUCTION SHEET.

CONCEALED BACK

SPUD TOILET

*-C-L-

TOP OF FIXTURE

152mm MIN.

(6) MIN.

240mm MAX.

(9-1/2) MAX.

450mm MAX. (17-3/4) MAX.

TOP OF

FIXTURE

*Note: The Critical Line (-C-L-) on Vacuum Breaker must typically be 6

above fixture. Consult Codes for details.

" (152mm) min.

RECOMMENDED TOOLS; Fig. 2.

1. Teon Tape

2. Flat Blade Screwdriver

3. Adjustable Wrench

4. Tape Measure

5. Hacksaw

6. Tubing Cutter

7. File

8. For Sweat Connection; Solder and Torch

9. 2.5mm Hex Wrench

10. 1.5mm Hex Wrench

PRIOR TO INSTALLATION

Note: Prior to installing the Selectronic™Flush

Valve the following items must be installed.

1. Toilet

2. Drain line

3. Water supply line

IMPORTANT:

• All plumbing and electrical wiring should be installed in accordance with applicable codes and regulations.

• The use of water hammer arrestors is strongly recommended for commercial applications. All piping

behind the walls should be properly secured and fastened.

• Water supply lines must be sized to provide an

adequate volume of water for each xture.

51mm

(2)

FINISHED FLOOR

51mm

(2)

FINISHED FLOOR

Fig. 2

10'

7 9 10

• Flush all water lines prior to operation (See Step 3). Dirt and debris can cause ush valve to run continuously.

• With the exception of Stop Valve Inlet, DO NOT

use pipe sealant or plumbing grease on any valve component or coupling!

• Protect the chrome or special nish on the Flushometer.

DO NOT USE toothed tools on nished surfaces to install or service these valves. Also see “Care and Cleaning” section of this manual.

• This product contains mechanical and/or electrical

components that are subject to normal wear. These components should be checked on a regular basis and replaced as needed to maintain the valve’s performance.

FINISHED FLOOR

M965640 Rev. 1.4 (11/17)

FLUSH VALVE INSTALLATION

INSTALL ELECTRICAL BOX; Fig. 3

1. Cut a 127x127mm (5"x 5") opening in nished wall for ELECTRICAL BOX (1) at the dimension shown.

Fig.3 (TOP SPUD FIXTURE ILLUSTRATED)

TOP

127mm

(5)

127mm

(5)

2. Rotate the 4 MOUNTING TABS (2) at against the

electrical box. Holding the MOUNTING TABS (2) in position, install the ELECTRICAL BOX (1) into the opening. Make sure the MOUNTING TABS (2) are behind the wall.

3. Tighten the 4 MOUNTING SCREWS (3) until the

ELECTRICAL BOX (1) is almost secure in the wall. Before tighting fully, rest a level at the top edge of the ELECTRICAL BOX (1) and make sure the box is level.

4. Cut a 2" diameter hole for outlet pipe at dimension

shown.*

INSTALL SWEAT ADAPTER; Fig. 4

CAUTION

Turn water supplies off before beginning

Note: Stop Valve inlet is 1" NPT. For optional sweat connection, install Sweat Adapter (1) (Supplied) for 1"

copper pipe supply line.

1. Clean the end of the supply pipe. Push the threaded SWEAT ADAPTER (1) until it is seated against the internal stop. Sweat the ADAPTER (1) to the pipe.

360mm MAX.

(14-3/16) MAX.

128mm MAX.

(5) MAX.

Fig. 4

115mm-134mm

(4-1/2 TO 5-1/4)

STOP

VALVE

OUTLET

TOP

*FOR HOLE LOCATION OF OUTLET PIPE ON BACK INLET FIXTURES, REFER TO FIXTURE BEING INSTALLED FOR CORRECT HEIGHT FROM FINISHED FLOOR

TOP

FILE

EDGES

STOP VALVE (1" NPT)

CLEAN & SOLDER TO ADAPTER (1)

2. Install the STOP VALVE (2) to the water supply line

with the outlet positioned as required (Behind the Wall).

3. Support piping as required.

FLUSH OUT SUPPLY LINES; Fig. 5

1. Open STOP VALVE (1).

2. Tur n on water supply line to ush line of any debris or

sediment.

3. Close STOP VALVE (1) and turn off water supply line.

Fig. 5

COUNTER-CLOCKWISE

OPENS STOP VALVE

CLOCKWISE CLOSES STOP VALVE

M965640 Rev. 1.4 (11/17)

+ 8 hidden pages