American Standard 606B.111, 606B.121, 606B.161, 606B.721, 606B.761 Installation Manual

SELECTRONIC

EXPOSED TOILET FLUSH VALVE AC POWERED PROXIMITY

1.1, 1.28, 1.6,

1.6/1.1 & 1.28/1.1 GPF

MODEL NUMBERS

606B.111 606B.121 606B.161 606B.721 606B.761

COVER PLATE

(Required for Front Installation Only)

Exposed Flush Valve for 1-1/2" Top Spud Bowls

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.

Certied to comply with ASME A112.19.2

Installation Instructions

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance, please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369) (In Toronto Area only: 1-905-306-1093)

M965644 EN REV. 1.6 (12/16)

Thank you for selecting American-Standard...the benchmark of ne quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

UNPACKING

Remove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton. Some items may be packaged partially assembled to other items.

1. Installation Instructions

2. Flush Valve Body Assembly

3. Vacuum Breaker Tube

4. Spud Coupling Nut and Washers

5. Spud Flange

6. Wall Escutcheon

7. Cover Tube

Some Residual Water May Remain In The Valve During Shipping.

8. Sweat Adapter

9. Stop Valve

CARE INSTRUCTIONS:

DO: CLEAN THE PRODUCT WITH CLEAR WATER, DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS,

OR A CLOTH WITH A COARSE SURFACE.

All American Standard Products Are Water Tested At Our Factory.

DO NOT REMOVE PROTECTIVE FILM FROM SENSOR EYE UNTIL INSTALLATION IS COMPLETE.

COVER PLATE

(Required For

Front Installation

Only)

POWER KIT - SOLD SEPARATELY

Hard-Wire AC

Power Kit

6067.111 6067.121 6067.161 6067.721 6067.761

6068.111 6068.121 6068.161 6068.721 6068.761

COVER PLATE

(Required for Front Installation Only)

Exposed Flushometer for 1-1/2" Top Spud Bowls

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.

(In Toronto Area only: 1-905-306-1093)

MODEL NUMBERS

SELECTRONIC

EXPOSED TOILET FLUSH VALVE AC POWERED PROXIMITY

1.1, 1.28, 1.6,

1.6/1.1 & 1.28/1.1 GPF

Installa tion Instructions

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance, please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(PK00.HAC)

Multi-AC

Power Kit

(PK00.MAC)

M965644 EN REV. 1.6 (12/16)

Fig. 1

Roughing-in Dimensions (Front Installation Shown)

Right or Left Hand Installation

See (Section 5) for converting Flush Valve to Left Hand Installation.

73 mm

(2-7/8")

120 mm

MANUAL

OVERRIDE

BUTTON

292 mm (11-1/2")

*Note: The Critical Line (-C-L-) on Vacuum Breaker must typically be 6

fixture. Consult Codes for details.

(4-3/4")

*-C-L-

152 mm MIN.

(6") MIN.

-C-L-

" (152 mm) above

SEE DETAIL “A”

305 mm MAX.

(12" MAX.)

108 - 134 mm (4-1/4" – 5-1/4")

TOP OF FIXTURE

51 mm (2") HOLE

FOR CONDUIT

86 mm (3-3/8)

(1" NPT)

412 mm

(16-3/16")

FINISHED WALL

DETECTION ZONE: 400 - 800 mm (15-3/4" – 31-1/2")

(FACTORY SETTING: 600 mm (23-5/8")

170 mm MAX. (6-11/16") MAX.

GENERAL DESCRIPTION:

SELECTRONIC® PROXIMITY TOILET FLUSH VALVE for 1-1/2" Top Spud Fixtures

CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.

15˚

4" (102 mm) SQ. BOX DEVICE COVER (PLASTER RING).

3/4" (19 mm) HIGH Hubbel-RACO #779 OR EQUAL

NOTE: INSTALL PLASTER RING SO THAT SCREW

HOLES ARE ON THE LEFT AND RIGHT SIDE OF BOX.

4" (102 mm) SQ. x 3-1/2" (89 mm) DEEP ELECTRICAL BOX

Hubbel-RACO #256 OR EQUAL (BY CONTRACTOR).

(BY CONTRACTOR).

FINISHED TILE WALL

DETAIL “A”

FINISHED PLASTER WALL

RECOMMENDED TOOLS; Fig. 2.

1. Teon Tape

2. Flat Blade Screwdriver

3. Adjustable Wrench

4. Tape Measure

5. Hacksaw

6. Tubing Cutter

7. File

8. For Sweat Connection; Solder and Torch

9. 2.5 mm Hex Wrench

10. 1.5 mm Hex Wrench

PRIOR TO INSTALLATION

Note: Prior to installing the Selectronic™Flush Valve the following items must be installed.

1. Toilet

2. Drain line

3. Water supply line

IMPORTANT:

• All plumbing and electrical wiring should be installed in accordance with applicable codes and regulations.

• The use of water hammer arrestors is strongly recommended for commercial applications. All piping

behind the walls should be properly secured and fastened.

• Water supply lines must be sized to provide an

adequate volume of water for each xture.

Fig. 2

10'

7 9 10

• Flush all water lines prior to operation. Dirt and debris can cause ush valve to run continuously.

• With the exception of Stop Valve Inlet, DO NOT use pipe sealant or plumbing grease on any valve component or coupling!

• Protect the chrome or special nish on the Flushometer. DO NOT USE toothed tools on nished surfaces to install or service these valves. Also see “Care and Cleaning” section of this manual.

• This product contains mechanical and/or electrical components that are subject to normal wear. These components should be checked on a regular basis and replaced as needed to maintain the valve’s performance.

M965644 EN REV. 1.6 (12/16)

1-1/2" TOP SPUD

FLUSH VALVE INSTALLATION

INSTALL SWEAT ADAPTER; Fig. 3

CAUTION

Note: Install Optional Sweat Adapter (Supplied) for copper pipe supply line.

1. Measure the distance (A) from the nished wall to the center of the inlet spud on the xture.

2. Cut the supply pipe 1-1/4" (A-B=C) shorter than the

measurement taken in Step 1. File any rough edges off the end of the supply pipe.

3. Clean the end of the supply pipe. Push the threaded

Adapter until it is seated against the internal stop. Sweat the Adapter to the pipe.

Turn water supplies off before beginning

Fig.3

FINISHED WALL

(A-B)=

FILE EDGES

CLEAN

ADAPTER

SOLDER ADAPTER

CENTER LINE OF FIXTURE SPUD

32mm (1-1/4")

INSTALL COVER TUBE, WALL

ESCUTCHEON and STOP VALVE; Fig. 4

1. Measure from nished wall to rst thread of Adapter

or threaded supply pipe (dimension “X”). Cut COVER TUBE (1) to length (X). Apply Teon Tape to the threaded end of the Adapter or supply pipe.

2. Push WALL ESCUTCHEON (2) onto the COVER TUBE (1).

Slide both onto the SUPPLY PIPE (3).

3. Push the COVER TUBE (1) in to expose the threads of

the supply pipe. With a wrench, thread the STOP VALVE (4)

onto the SUPPLY PIPE (3). Align and tighten.

4. Pull COVER TUBE (1) against STOP VALVE (4) and

push WALL ESCUTCHEON (2) against nished wall.

INSTALL VACUUM BREAKER

TUBE; Fig. 5

1. Place the SPUD FLANGE (1) over the spud on

the Fixture.

Fig. 4

Fig. 5

FINISHED WALL

TEFLON TAPE

2. Place FRICTION WASHER (3) and SEAL WASHER

(4) inside SPUD COUPLING NUT (2) and thread onto Spud. Do not tighten fully.

3. Insert the VACUUM BREAKER TUBE (5) into the

SPUD COUPLING NUT (2) and push it down.

Note: If cutting VACUUM BREAKER TUBE (5) to size, note that Critical Line (C/L) on Vacuum Breaker must typically be 6" (152mm) above xture. Consult Code for details.

M965644 EN REV. 1.6 (12/16)

+ 7 hidden pages