American Standard 606B.101, 606B.051, 606B.025, 606B.013 Installation Manual
SELECTRONIC
®
EXPOSED URINAL FLUSH VALVE
AC POWERED PROXIMITY
0.125 0.25 0.5 & 1.0 GPF
MODEL NUMBERS
606B.101 606B.051 606B.025 606B.013
COVER PLATE
(Required for Front Installation Only)
Exposed Flushometer
for 3/4" Top Spud Urinals
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.
Certied to comply with ASME A112.19.2
© 2017 AS America, Inc.
Installation Instructions
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com
or e-mail us at: CRTTEAM@americanstandard.com
For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093)
© 2017 AS America Inc.
1
M965645 EN REV. 1.7 (5/17)
Thank you for selecting American-Standard...the benchmark of ne quality for over 100 years. To ensure that your
installation proceeds smoothly--please read these instructions carefully before you begin.
UNPACKING
Remove the Flush Valve items from the carton. The illustration below shows all items after they have been
removed from the carton. Some items may be packaged partially assembled to other items.
1. Installation Instructions
2. Flush Valve Body Assembly
3. Vacuum Breaker Tube
4. Spud Coupling Nut and Washers
5. Spud Flange
6. Wall Escutcheon
7. Cover Tube
Some Residual Water May Remain In The Valve During Shipping.
8. Sweat Adapter
9. Stop Valve
CARE INSTRUCTIONS:
DO: CLEAN THE PRODUCT WITH CLEAR WATER, DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS,
OR A CLOTH WITH A COARSE SURFACE.
All American Standard Products Are Water Tested At Our Factory.
DO NOT REMOVE PROTECTIVE FILM FROM SENSOR
EYE UNTIL INSTALLATION IS COMPLETE.
2
COVER PLATE
(Required For
Front Installation
Only)
7
8
6
POWER KIT - SOLD SEPARATELY
Hard-Wire AC
Power Kit
1
®
COVER PLATE
(Required for Front Installation Only)
Exposed Flushometer
for 3/4" Top Spud Urinals
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.
(In Toronto Area only: 1-905-306-1093)
MODEL NUMBERS
6061.101 6061.051 6061.025 6061.013
6062.101 6062.051 6062.025 6062.013
SELECTRONIC
EXPOSED URINAL FLUSH VALVE
AC POWERED PROXIMITY
0.125 0.25 0.5 & 1.0 GPF
3
© 2015 AS America, Inc.
Installa tion Instructions
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com
or e-mail us at: CRTTEAM@americanstandard.com
For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)
(PK00.HAC)
9
Multi-AC
Power Kit
(PK00.MAC)
4
5
2
M965645 EN REV. 1.7 (5/17)
Fig. 1 (Before November 2017)
Roughing-in Dimensions (Front Installation Shown)
Right or Left Hand Installation
See (Section 5) for converting Flush
Valve to Left Hand Installation.
SEE DETAIL “A”
FINISHED WALL
GENERAL DESCRIPTION:
SELECTRONIC® PROXIMITY URINAL FLUSH VALVE
Exposed Flushometer for 3/4" Top Spud Fixtures
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.
73 mm
MANUAL
OVERRIDE
BUTTON
292 mm
(11-1/2")
117 mm
(4-5/8")
*-C-L-
152 mm MIN.
(6") MIN.
(2-7/8")
-C-L-
305 mm MAX.
(12" MAX.)
115 - 134 mm
(4-1/2" - 5-1/4")
TOP OF
FIXTURE
*Note: The Critical Line (-C-L-) on Vacuum
Breaker must typically be 6
fixture. Consult Codes for details.
" (152mm) above
Fig. 1A (After November 2017)
Roughing-in Dimensions Fig. 1
SEE DETAIL “A”
51 mm (2") HOLE
FOR CONDUIT
86 mm
(3-3/8)
(3/4" NPT)
409 mm
(16-1/8")
DETECTION ZONE: 400 - 800 mm (15-3/4" – 31-1/2")
(FACTORY SETTING: 600 mm (23-5/8")
4" (102 mm) SQ. BOX DEVICE COVER (PLASTER RING).
3/4" (19 mm) HIGH Hubbel-RACO #779 OR EQUAL
NOTE: INSTALL PLASTER RING SO THAT SCREW
HOLES ARE ON THE LEFT AND RIGHT SIDE OF BOX.
4" (102 mm) SQ. x 3-1/2" (89 mm) DEEP ELECTRICAL BOX
Hubbel-RACO #256 OR EQUAL (BY CONTRACTOR).
76 mm MAX.
(3") MAX.
FINISHED WALL
15˚
(BY CONTRACTOR).
FINISHED TILE WALL
DETAIL “A”
FINISHED PLASTER WALL
73 mm
MANUAL
OVERRIDE
BUTTON
292 mm
(11-1/2")
114 mm
(4-1/2")
*-C-L-
152 mm MIN.
(6") MIN.
(2-7/8")
-C-L-
305 mm MAX.
(12" MAX.)
115 - 134 mm
(4-1/2" - 5-1/4")
TOP OF
FIXTURE
*Note: The Critical Line (-C-L-) on Vacuum
Breaker must typically be 6
fixture. Consult Codes for details.
" (152mm) above
51 mm (2") HOLE
FOR CONDUIT
86 mm
(3-3/8)
(3/4" NPT)
406 mm
(16")
DETECTION ZONE: 400 - 800 mm (15-3/4" – 31-1/2")
(FACTORY SETTING: 600 mm (23-5/8")
15˚
76 mm MAX.
(3") MAX.
3
M965645 EN REV. 1.7 (5/17)
RECOMMENDED TOOLS; Fig. 2.
1. Teon Tape
2. Flat Blade Screwdriver
3. Adjustable Wrench
4. Tape Measure
5. Hacksaw
6. Tubing Cutter
7. File
8. For Sweat Connection; Solder and Torch
9. 2.5 mm Hex Wrench
10. 1.5 mm Hex Wrench
Fig. 2
1
2
10'
4
5
7 9 10
3
6
8
PRIOR TO INSTALLATION
Note: Prior to installing the Selectronic™Flush
Valve the following items must be installed.
1. Urinal
2. Drain line
3. Water supply line
IMPORTANT:
• All plumbing and electrical wiring should be
installed in accordance with applicable codes
and regulations.
• The use of water hammer arrestors is strongly
recommended for commercial applications. All piping
behind the walls should be properly secured and
fastened.
• Water supply lines must be sized to provide an
adequate volume of water for each xture.
• Flush all water lines prior to operation. Dirt and debris can
cause ush valve to run continuously.
• With the exception of Stop Valve Inlet, DO NOT
use pipe sealant or plumbing grease on any
valve component or coupling!
• Protect the chrome or special nish on the Flushometer.
DO NOT USE toothed tools on nished surfaces to install
or service these valves. Also see “Care and Cleaning”
section of this manual.
• This product contains mechanical and/or electrical
components that are subject to normal wear. These
components should be checked on a regular basis and
replaced as needed to maintain the valve’s performance.
4
M965645 EN REV. 1.7 (5/17)
Loading...