|
|
|
|
|
|
|
User Instructions |
||||
|
American DJ® |
||||
|
6122 S. Easterns Ave. |
||||
|
Los Angeles Ca. 90040 |
||||
4/08 |
www.americandj.com |
||||
MB DMX II™ |
General Information |
Unpacking..................................................................................... |
3 |
Introduction.................................................................................. |
3 |
Customer Support............................................................................. |
3 |
Safety Precautions............................................................................... |
4 |
Features......................................................................................... |
5 |
Registration.............................................................................. |
5 |
Set-Up |
|
DMX Linking................................................................................... |
6 |
Data Cable Requirements............................................................ |
6 |
Termination................................................................................ |
7 |
5 Pin Conversion......................................................................... |
7 |
Linking........................................................................................... |
8 |
Operating Modes |
|
Stand Alone................................................................................. |
10 |
Master/Slave.................................................................................. |
10 |
DMX ...................................................................................... |
11 |
Mounting................................................................................... |
12 |
Breaker Reset..................................................................................... |
12 |
DMX Traits...................................................................................... |
13 |
Master/Slave Quick Reference Chart................................................. |
14 |
Warranty......................................................................................... |
15 |
Specifications.............................................................................. |
16 |
©American DJ Supply® - www.americandj.com - MB DMX II™ Instruction Manual Page 2
MB DMX II™ |
General Information |
General Instructions: To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference.
Unpacking: Thank you for purchasing the MB DMX II™ by American DJ®. Every MB DMX II™ has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without first contacting customer support.
Introduction: The MB DMX II™ is a unique intelligent mirror ball motor that may be operated in three modes; DMX-512, Stand-Alone, or Master/
Slave. The MB DMX II™ allows you to control the operation of a mirror ball motor as well as the lamps via DMX operation. You may also link several MB DMX II™ motors together to obtain universal speed and rotation.
An optional MINI/C black out controller may be purchased separately.
Customer Support: American DJ® provides a toll free customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.americandj.com for any comments or suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice: |
(800) |
322-6337 |
Fax: |
(323) |
582-2941 |
E-mail: |
support@americandj.com |
|
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact your nearest American DJ® dealer.
MB DMX II™ |
Safety Precautions |
Safety Issues:
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit
•Do not attempt to operate this unit if the power cord has been frayed or broken
•Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short
•Disconnect from main power before making any type of connection
•Do not remove the cover under any conditions. There are no user serviceable parts inside
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall
•Do not attempt to operate this unit, if it becomes damaged
•This unit is intended for indoor use only, use of this product outdoors voids all warranties
•During long periods of non-use, disconnect the unit’s main power
•Always mount this unit in safe and stable matter
•Power cords should be routed so they are not likely to be walked on, pinched by items placed upon or against them.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A.The power-supply cord or the plug has been damaged.
B.Objects have fallen, or liquid has been spilled into the appliance.
C.The appliance has been exposed to rain or water.
D.The fixture does not appear to operate normally or exhibits a marked change in performance.
©American DJ® - www.americandj.com - MB DMX II™ Instruction Manual Page 3 |
©American DJ® - www.americandj.com - MB DMX II™ Instruction Manual Page 4 |
MB DMX II™ |
Features |
•Micro-Stepping Motors for Smooth Rotation
•Uses Two DMX Channels
•DMX-512 Protocol Compatible
•Variable Head Rotation Speed
•Built-In Rigging Point
•Stand-Alone or Master/Slave Operation
•Linkable
•Two Built-In DMX Controlled AC Power Sockets
•Heavy Duty Mirror Ball Motor
•Rated for 20” Mirror Balls
•Optional Mini/C Blackout Controller
MB DMX II™ |
Product Registration |
The MB DMX II™ carries a one year (365 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by contacting our customer support team on our toll free customer support number at (800) 322-6337. All packages returned to service not displaying a R.A. number on the outside of the package will be returned to the shipper.
MB DMX II™ |
Set Up |
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your American DJ®
MB DMX II.™ Because line voltage may vary from venue to venue, you should be sure your unit voltages matches the wall outlet voltage before attempting to operate you fixture.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/ Slave Operation): The MB DMX II™ can be controlled via DMX-512 protocol. The American DJ® MB DMX II™ is a two channel DMX unit. The DMX address is set on the side panel using the dipswitches. Your unit and your DMX controller require a standard
3-pin XLR connector for data input and data output (Figure 1). If you are making your own cables, be sure to use standard two conductor shielded cable (This cable may be purchased at almost all pro sound and lighting stores). Your cables should be made with a male and female
XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and can not be split.
©American DJ® - www.americandj.com - MB DMX II™ Instruction Manual Page 5 |
©American DJ® - www.americandj.com - MB DMX II™ Instruction Manual Page 6 |
Loading...