American DJ Aggressor User Instructions

0 (0)

American DJ®

AGGRESSOR

User Instructions

Aggressor™

Unpacking

Thank you for purchasing the Aggressor™ by American DJ® Every Aggressor™ has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your unit for any damage and be sure all equipment necessary to operate the system has arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Please do not return the unit to your dealer without fi rst contacting customer support.

Aggressor™

Introduction

Customer Support:

American DJ® provides a toll free customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.americandj.com for any comments or suggestions. For service related issue please contact American DJ® Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacifi c Standard Time

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: support@americandj.com

Warning! To prevent or reduce the risk of electrical shock or fi re, do not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact your nearest American DJ dealer

PLEASE do not discard the shipping carton in the trash. Please recycle when ever possible

Breaker: This unit may pop the emergency circuit breaker located on the rear of the unit if the maximum allotted amperage load of 10 amps (5 amps for 220v users) is reached. If the breaker pops the unit will not function until the breaker is reset. To reset the breaker follow the reset function on page 5

Rev 05/02

©American DJ Supply® - www.americandj.com - Aggressor™ Instruction Manual Page 2

Aggressor™

General Instructions

Please carefully read and understand the instructions in this manual thoroughly, before attempting to operate this unit. These instructions contain important safety information regarding the proper use and maintenance of this unit. Please keep this manual in a secure place for future reference

Aggressor™

Precautions

Keep the outside of this device dry at all times. Do not spill water or other liquids into or on to your unit. To prevent fi re or shock hazard, do not expose this product to rain or moisture

Be sure to save the packing carton in the event you may have to return the unit for service

This unit is designed for interior use only. Do not use this unit out doors. Use of product outdoors will void the warranty

Be sure that the local power outlet match that of the required voltage for your unit

Never attempt to operate this unit if the power cord becomes frayed or broken.

Never attempt to operate this unit, if it becomes damaged in any

way

Always route your power cord out of the way of foot traffi c

Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fi re in the rare case of an internal short

Disconnect the unit’s main power when left unused for long periods of time

Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall

Never block the ventilation holes

Never operate this unit when the cover is removed

This unit is for adult use only. Keep out of the reach of children

Aggressor™

Features

48 Vibrantly Colored Beams

Easy Lamp Replacement

Fan Cooled

Bright LL-64514 120v/300w Lamp

Sound-Active

Aggressor™

Halogen Lamp Warning

This fixture is fitted with halogen lamps which are highly susceptible to damage if improperly handled. Never touch lamp with your bare fingers as the oil from your hands will shorten lamp life. Also, never move the fixture until the lamps have had ample time to cool. Remember, lamps are not covered under warranty conditions

Aggressor™

Power Supply

Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your American DJ®

Aggressor.™ The American DJ® Aggressor is available in a 120v and

220v version. Because line voltage may vary from venue to venue, be sure to plug your fi xture into a wall outlet with a matching power supply before attempting to operate

Aggressor™

Operation

Introduction: The Aggressor™ is a powerful effect for clubs, mobile dj's, roller rinks and bowling alleys. The Aggressor™ especially looks great in pairs. The Aggressor™ creates a dramatic cluster of 40 multicolored beams. This unit features an internal microphone that allows the internal wheel to be triggered by sound, thus bouncing the colorful beams of light up and down to the beat of the music. The Aggressor™ is fan cooled. For best result use this unit in conjunction with a fog machine to enhance the beams

Operating Instructions: The Aggressor™ is ready to be hung or set on the ground in a safe position. When mounting this unit to truss be sure to use a clamp. Plug the unit in to a standard properly matched power wall outlet. After plugging the unit in, the fixture will react to the beat of the music via the sound active internal microphone. The unit requires sound to activate the movement. The sound sensitivity is preset at the factory to a moderate level and is not user selectable

Caution! Be sure not to obstruct cooling vents and keep this unit in a well ventilated area. Never open the unit while in use. Avoid touching the lamps, the lamp will get extremely hot under normal usage and may cause serious injury.

+ 2 hidden pages