Alto Shaam ED2-60 Installation Manual

ED2-60

W164 N9221 Water Stre et • P.O. Box 450 • Menomonee Falls, Wis consin 53 052-0 450 USA

PHONE: 262.251.3800 • 80 0.558.8744

US A/CAN ADA FAX: 262.251.7067 • 800.329.8744 U .S. A. ONLY

www.alto- shaam.com

H e a t e d D i s p l a y C a s e s

F u l l S e r v i c e o r S e l f S e r v i c e

Models:

ED2-60

P RI NT ED I N U .S .A.

• INSTALLATION

• OPERATION

• MAINTENANCE

MN- 28 84 7 • 1 2/ 09

Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Procedures and Precautions . . . . . . . . . . . . . 2

Installation

Installation Requirements . . . . . . . . . . . . . . . . . . 3

Clearance Requirements. . . . . . . . . . . . . . . . . . . 3

Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Dimension Drawings . . . . . . . . . . . . . . . . . . . . . . 4

Options & Accessories. . . . . . . . . . . . . . . . . . . . . 4

Electrical Connection. . . . . . . . . . . . . . . . . . . . . . 5

Operating Instructions

User Safety Information. . . . . . . . . . . . . . . . . . . . 6

Start-up Operation. . . . . . . . . . . . . . . . . . . . . . . . 6

Operating Procedures . . . . . . . . . . . . . . . . . . . . . 7

Pan Configurations . . . . . . . . . . . . . . . . . . . . . . . 8

General Holding Guidelines . . . . . . . . . . . . . . . . . 9

Care and Cleaning

Cleaning and Preventive Maintenance. . . . . . . . 10

Protecting Stainless Steel Surfaces. . . . . . . . . . 10

Cleaning Agents . . . . . . . . . . . . . . . . . . . . . . . . 10

Cleaning Materials. . . . . . . . . . . . . . . . . . . . . . . 10

Equipment Care. . . . . . . . . . . . . . . . . . . . . . . . . 11

Clean the Probes. . . . . . . . . . . . . . . . . . . . . . . . 11

Clean Daily . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Sanitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Service

Cable Replacement Kits . . . . . . . . . . . . . . . . . . 13

Full Assembly, Front View. . . . . . . . . . . . . . . 14-15

Inner Top Assembly . . . . . . . . . . . . . . . . . . . . . . 16

Control Assembly . . . . . . . . . . . . . . . . . . . . . . . 17

Wire Diagrams

ED2-60, 230V . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Warranty

Transportation Damage and Claims. . . Back Cover

Limited Warranty . . . . . . . . . . . . . . . . . Back Cover

D E L I V E R Y

This Alto-Shaam appliance has been thoroughly tested and inspected to ensure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier. See

Transportation Damage and Claims section

located in this manual.

This appliance, complete with unattached items and accessories, may have been delivered in one or more packages. Check to ensure that all standard items and options have been received with each model as ordered.

Save all the information and instructions packed with the appliance. Complete and return the warranty card to the factory as soon as possible to ensure prompt service in the event of a warranty parts and labor claim.

This manual must be read and understood by all people using or installing the equipment model. Contact the Alto-Shaam service department if you have any questions concerning installation, operation, or maintenance.

N O TE: All claims for warranty must include the

full model number and serial number of the unit.

U N P A C K I N G

1. Carefully remove the appliance from the carton or crate.

N O TE: Do not discard the

carton and other packaging material until you have inspected the unit for hidden damage and tested it for proper operation.

2. Read all instructions in this manual carefully before initiating the installation of this appliance.

DO NOT DISCARD THIS MANUAL. This manual is considered to be part of the appliance and is to be provided to the owner or manager of the business or to the person responsible for training operators. Additional

manuals are available from the Alto-Shaam

service department.

3. Remove all protective plastic film, packaging materials, and accessories from the appliance before connecting electrical power. Store any accessories in a convenient place for future use.

ED2 - 60 Op e rat i on & Car e M anu a l • 1

1. This appliance is intended to hold or process

foods for the purpose of human consumption. No other use for this appliance is authorized or recommended.

2. This appliance is intended for use in commercial

establishments where all operators are familiar with the purpose, limitations, and associated hazards of this appliance. Operating instructions and warnings must be read and understood by all operators and users.

3. Any troubleshooting guides, component views,

and parts lists included in this manual are for general reference only and are intended for use by qualified technical personnel.

4. This manual should be considered a permanent

part of this appliance. This manual and all supplied instructions, diagrams, schematics, parts lists, notices, and labels must remain with the appliance if the item is sold or moved to another location.

N O T E : Used to notify personnel of

installation, operation, or maintenance information that is important but not hazard related.

C A U T I O N

Used to indicate the presence of a hazard that can or will cause minor personal injury, property damage, or a potential unsafe practice if the warning included with this symbol is ignored.

C A U T I O N

Used to indicate the presence of a hazard that can or will cause minor or moderate personal injury or property damage if the warning included with this symbol is ignored.

D A N G E R

Used to indicate the presence of a hazard that WILL cause severe personal injury, death, or substantial property damage if the warning included with this symbol is ignored.

W A R N I N G

Used to indicate the presence of a hazard that CAN cause personal injury, possible death, or major property damage if the warning included with this symbol is ignored.

SAF ETY P ROC EDU RES AND PR ECA UTI ONS

Knowledge of proper procedures is essential to the safe operation of electrically and/or gas energized equipment. In accordance with generally accepted product safety labeling guidelines for potential hazards, the following signal words and symbols may be used throughout this manual.

N O T E

For equipment delivered for use in any location regulated by the following directive:

DO NOT DISPOSE OF ELECTRICAL OR ELECTRONIC EQUIPMENT WITH OTHER MUNICIPAL WASTE.

ED2 - 60 Op e rat i on & Car e M anu a l • 2

S I T E IN S TA L L A T I O N

C A U T I O N

METAL PARTS OF THIS EQUIPMENT BECOME EXTREMELY HOT WHEN IN OPERATION. TO AVOID BURNS, A

LWAYS USE HAND PROTECTION

WHEN OPERATING THIS APPLIANCE.

D A N G E R

IMPROPER INSTALLATION, ALTERATION, ADJUSTMENT, S

ERVICE, OR MAINTENANCE COULD RESULT IN SEVERE INJURY, DEATH, OR CAUSE PROPERTY DAMAGE.

READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.

C A U T I O N

TO PREVENT PERSONAL INJURY,

USE CAUTION WHEN MOVING OR

LEVELING THIS APPLIANCE.

I N S TA L L AT I O N

In order to maintain established National Sanitation Foundation standards, all stationary floor models must be sealed to the floor with a R.T.V. or silastic meeting N.S.F. requirements or have 6" (152mm) unobstructed clearance beneath the unit.

1. The appliance must be installed on a stable and level surface.

2. DO N OT install this appliance in any area where it may be affected by any adverse conditions such as steam, grease, dripping water, high temperatures, or any other severely adverse conditions.

3. DO N OT install a heated display case near a cold air source such as a freezer, air conditioning vents, or in any area where outside air fluctuation can affect performance.

4. This appliance must be kept free and clear of any obstructions blocking access for maintenance or service.

MINIMUM CLEARANCE REQUIREMENTS

Counter and table units must be mounted on legs of a sufficient 4" (102mm) height to provide minimum unobstructed space beneath the unit. These legs are supplied with the unit. Warranty will become null and void if these directions are not followed.

ED2 - 60 Op e rat i on & Car e M anu a l • 3

A number of adjustments are associated with initial installation and start-up. It is important that these adjustments be conducted by a qualified service technician. Installation and start-up adjustments are the responsibility of the dealer or user. These adjustments include but are not limited to thermostat calibration, door adjustment, leveling, electrical hook-up and installation of optional casters or legs.

LEVELING

Level the appliance from side-to-side and front-to-back with the use of a spirit level.

We recommend checking the level periodically to make certain the floor has not shifted nor the appliance moved.

NOTE: Failure to properly level this appliance

can cause improper function.

I N S TA L L AT I O N

30-1/

8" (765mm

)

60" (1524mm)

57-7/16" (1457mm)

26-1

/2"

72m

3-2/3"

(92mm)

100.0°

44-5/16" (1125mm)

30" (763mm)

2-1/2"

(63mm)

9-5/8"

(

243mm)

10"

(254mm)

-1/2"

(

114mm)

26-1/2" (672mm)

30-1/8" (765mm)

55-13/16" (1416mm)

S I T E IN S TA L L A T I O N

E D 2 - 6 0

PROFILE

ED2- 6 0 — O PTIO N S & ACC E S SORI E S

DESCRIPTION ED2-60

BUTTING KIT

CARVING STATION

GAUGE, INTERIOR AMBIENT TEMPERATURE

GLASS, TEMPERED END PANE, BRONZE KIT

PANEL KIT, COUNTER TOP BRUSHED STAINLESS STEEL

CUSTOM COLOR

PLATFORM SCALE RIGHT HAND

LEFT HAND

THERMOSTAT GUARD COVER PLATE

WORK SHELF WITH GRAVY LANE

5009001

5001874

AVAILABLE

5001143

AVAILABLE

5001307

5001308

5007660 (2 REQ'D)

5005638

ED2 - 60 Op e rat i on & Car e M anu a l • 4

E L E C T R I C A L C O N N E C T I O N

D A N G E R

ELECTRICAL CONNECTIONS MUST

BE MADE BY A QUALIFIED SERVICE

TECHNICIAN IN ACCORDANCE WITH

APPLICABLE ELECTRICAL CODES.

D A N G E R

To avoid electrical shock, this appliance MUST be adequately grounded in accordance with local electrical codes or, in the absence of local codes, with the current edition of the National Electrical Code ANSI/NFPA No. 70. In Canada, all electrical connections are to be made in accordance with CSA C22.1, Canadian Electrical Code Part 1 or local codes.

D A N G E R

ENSURE POWER SOURCE

MATCHES VOLTAGE STAMPED

ON APPLIANCE NAMEPLATE.

E L E C T R I C A L

E D2- 6 0

VO LTAGE PH ASE C YCL E/H Z AM PS kW

230V (AGC Y)

1 50 14.6 3.4

BAR E EN D, NO PLU G

N O TE: 230V appliances must be connected

to an electrical circuit that is protected by an external GFCI outlet.

Hard wired models:

Hard wired models must be equipped with a country certified external allpole disconnection switch with sufficient contact separation.

If a power cord is used for the connection of the product an oil resistant cord like H05RN or H07RN or equivalent must be used.

The appliance must be installed by a qualified service technician. The oven must be properly grounded in accordance with the National

lectrical Code and applicable local codes.

Plug the unit into a properly grounded receptacle ONLY, positioning the unit so that the plug is easily accessible in case of an emergency. Arcing will occur when connecting or disconnecting the unit unless all controls are in the “

Proper receptacle or outlet configuration or permanent wiring for this unit must be installed by a licensed electrician in accordance with applicable local electrical codes.

OF F” position.

I N S TA L L AT I O N

REGARDING INTERNATIONAL STANDARD UNITS:

If the unit is not equipped with flexible cord with plug, an all-pole, country-approved disconnection device that has a contact separation of at least 3mm in all poles must be incorporated in the fixed wiring for disconnection. When using a cord without a plug, the green/yellow conductor shall be connected to the terminal that is marked with the ground symbol. If a plug is used, the socket outlet must be easily accessible. If the power cord needs replacement, use a similar one obtained from the distributor.

Fo r 230V un its: To prevent an electrical shock hazard between the appliance and other appliances or metal parts in close vicinity, an equalization-bonding stud is provided. An equalization bonding lead must be connected to this stud and the other appliances / metal parts to provide sufficient protection against potential difference. The terminal is marked with the following symbol.

ED2 - 60 Op e rat i on & Car e M anu a l • 5

+ 14 hidden pages