Alto Shaam CS-200 User Manual

Item no. _______________________
U.S.A./C ANADA
U.S.A.
CS-200
Hot Food Holding Carving Station
l
Halo Heat . . . a controlled, uniform heat source
radiating heat directly from the carving surface.
l
The xed lamp assembly provides additional heat to the product surface for greater surface temperaturecontrol.
l
Proper and safe serving temperatures are maintained without additional cooking.
l
The heated surface is recessed to catch drippings.
l
The sanitary cutting board with gravy lane is removable and listed with NSF and USDA.
l
The carving station is designed to t on top of a Halo Heat Cook & Hold oven, Heated Holding Cabinet, or suitable for placement on any surface.
l
A clear glass customer breath guard easily slides in place and meets new NSF breath guard specications.
Short Form Spec
The Alto-Shaam CS-200 hot food holding carving station is constructed with stainless steel and includes one (1) On/Off power switch and one (1) indicator light. The heated base is controlled by one (1) three-position toggle switch for Low/Medium/High heat. Two (2) 250-watt infrared heat lamps are controlled by one (1) On/Off switch. The heated surface is recessed to catch drippings. The CS-200 is furnished with one (1) set of 1" (25mm) legs and one (1) 21-5/8" x 21-5/8" x 1/2" (550mm x 550mm x 13mm) cutting board.
Model CS-200: Carving station with two lamps
Model CS-200/S: Carving station with two lamps and clear glass customer breath guard
Factory-installed Options
Electrical 120V, 1ph, 60Hz
230V, 1ph, 50/60Hz
Printed in the U.S.A.
W164 N9221 Water StreetP.O. Box 450Menomonee Falls, Wisconsin 53052-0450U.S.A.
Phone: 262.251.3800 800.558.8744
Due to ongoing product improvement, specifications are subject to change without notice.
www.alto-shaam.com
Fax: 262.251.7067 800.329.8744
only
#03 - 08/16
Heated Surface
HZ
NEMA 5-15P
PLUG
PLUGS RATED
CEE 7/7 CH2-16P BS 1363 AS/NZS 3112
21-11/16" (551mm)
22-3/8" (568mm)
Heated Surface
25-3/4" (654mm)
without breath guard
28" (660mm)
with breath guard
18--13/16" (477mm)
CS-200
Hot Food Holding Carving Station
31-9/16" (801mm)
33-3/16" (842mm)
1-9/16" (39mm)
12-7/8" (326mm)
Cord
Dimensions: (H x W x D)
CS-200: 33-3/16" x 25-3/4" x 29-5/16" (842mm x 654mm x 744mm)
CS-200/S: 33-3/16" x 26" x 30-13/16" (842mm x 660mm x 782mm)
Product/Pan Capacity
70 lbs (32 kg) max.
(large steamship round)
Installation Requirements
Carving station must be installed on a stable level surface, and must not be installed in any area where it may be affected by steam, grease, dripping water, high temperatures, or any other severely adverse conditions.
Stacking Congurations
on 750-S holding cabinet
on 750-TH-II or 750-TH/III cook & hold oven
on 767-SK or 767-SK/III smoker oven
Notice: Remove rubber feet and spacers prior to installation
on 750 & 767 series units.
Attention
Warranty does not apply if the carving station is ooded or immersed in water.
#03 - 08/16
W164 N9221 Water StreetP.O. Box 450Menomonee Falls, Wisconsin 53052-0450U.S.A. Phone: 262.251.3800 800.558.8744 U.S.A./Canada Fax: 262.251.7067 800.329.8744 U.S.A. only
Due to ongoing product improvement, specifications are subject to change without notice.
" (22mm)
7/8
29-5/16" (744mm)
without breath guard
30-13/16" (782mm)
with breath guard
Cord
Electrical  CS200
V PH
120 1 60 6.3 0.75
230 1 50/60 3.26 0.75
A kW
15A - 120V
250V
Weight* (est.)
CS-200 CS-200/S
Net: 60 lb (27 kg) Ship: 150 lb (68 kg)
Crate dimensions (
l x w x h): 35" x 35" x 41"
Net: Contact factory Ship: 170 lbs (77 kg)
(889mm x 889mm x 1041mm)
*Domestic ground shipping information. Contact factory for export
weight and dimensions.
Accessories
Carving Holders
Prime Rib
HL-2635
Steamship Round
Cutting Board
Full-size: 21-5/8" x 21-5/8" x 1/2"
(550mm x 550mm x 13mm)
Half-size: 10-3/4" x 21-5/8" x 1/2"
(273mm x 550mm x 13mm)
BA-28066
BA-29244
www.alto-shaam.com
Printed in the U.S.A.
4459
Loading...