Alcatel-Lucent SPEEDTOUCH 608 WL User Manual

SpeedTouch™608 WL

Wireless Business DSL Routers

CLI Reference Guide

Release R5.3.1

SpeedTouch™

608 WL

CLI Reference Guide

R5.3.1

Copyright

Copyright ©1999-2005 THOMSON. All rights reserved.

Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization
from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice,
and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or
inaccuracies that may appear in this document.

Thomson Telecom Belgium
Prins Boudewijnlaan, 47
B-2650 Edegem
Belgium

www.speedtouch.com

Trademarks

The following trademarks are used in this document:

 SpeedTouch™ is a trademark of THOMSON.
 Microsoft®, MS-DOS®, Windows® and Windows NT® are either registered trademarks or trademarks of Microsoft Corpo-

ration in the United States and/or other countries.

 UNIX® is a registered trademark of UNIX System Laboratories, Incorporated.
 Apple® and Mac OS® are registered trademarks of Apple Computer, Incorporated, registered in the United States and

other countries.

 Adobe, the Adobe logo, Acrobat and Acrobat Reader are trademarks or registered trademarks of Adobe Systems, Incorpo-

rated, registered in the United States and/or other countries.

 Netscape® and Netscape Navigator® are registered trademarks of Netscape Communications Corporation.
 Ethernet™ is a trademark of Xerox Corporation.
 UPnP™ is a certification mark of the UPnP™ Implementers Corporation.
 Wi-Fi® and the Wi-Fi logo are registered trademarks of the Wi-Fi Alliance. "Wi-Fi CERTIFIED", "Wi-Fi ZONE", "Wi-Fi Alli-

ance", their respective logos and "Wi-Fi Protected Access" are trademarks of the Wi-Fi Alliance.

Other products may be trademarks or registered trademarks of their respective manufacturers.

Document Information

Status: v1.0 (June 2005)
Reference: E-DOC-CTC-20050531-0061
Short Title: CLI Reference Guide ST608 WL R5.3.1

Contents

Contents

About this Document ....................................................................................1

ADSL Commands........................................................................................... 3

adsl config.....................................................................................................................................................4

adsl info.........................................................................................................................................................5

ATM Commands ............................................................................................ 7

atm flush ....................................................................................................................................................... 9

atm ifadd..................................................................................................................................................... 10

atm ifattach................................................................................................................................................. 11

atm ifconfig.................................................................................................................................................12

atm ifdelete.................................................................................................................................................14

atm ifdetach................................................................................................................................................15

atm iflist ...................................................................................................................................................... 16

atm bundle add ..........................................................................................................................................17

atm bundle attach ......................................................................................................................................18

atm bundle config ...................................................................................................................................... 19

atm bundle clear.........................................................................................................................................20

atm bundle delete ......................................................................................................................................21

atm bundle detach .....................................................................................................................................22

atm bundle flush ........................................................................................................................................23

atm bundle ifadd ........................................................................................................................................24

atm bundle ifconfig....................................................................................................................................25

atm bundle ifdelete .................................................................................................................................... 26

atm bundle list............................................................................................................................................27

atm cac config ............................................................................................................................................28

atm cac list..................................................................................................................................................29

atm cac overbooking.................................................................................................................................. 30

atm debug aal5stats................................................................................................................................... 31

atm debug gstats........................................................................................................................................ 32

atm debug portstats................................................................................................................................... 33

atm oam config ..........................................................................................................................................34

atm oam list................................................................................................................................................ 35

atm oam modify.........................................................................................................................................36

atm oam ping ............................................................................................................................................. 37

atm oam cc list ...........................................................................................................................................38

atm oam cc modify ....................................................................................................................................39

atm oam cc send ........................................................................................................................................40

E-DOC-CTC-20050531-0061 v1.0

i

Contents

atm oam vclb add....................................................................................................................................... 41

atm oam vclb del........................................................................................................................................42

atm oam vclb list........................................................................................................................................ 43

atm phonebook add...................................................................................................................................44

atm phonebook autolist.............................................................................................................................45

atm phonebook delete...............................................................................................................................46

atm phonebook flush.................................................................................................................................47

atm phonebook list ....................................................................................................................................48

atm qosbook add........................................................................................................................................ 49

atm qosbook config ...................................................................................................................................50

atm qosbook ctdadd ..................................................................................................................................51

atm qosbook ctddelete ..............................................................................................................................53

atm qosbook ctdlist....................................................................................................................................54

atm qosbook delete.................................................................................................................................... 55

atm qosbook flush...................................................................................................................................... 56

atm qosbook list.........................................................................................................................................57

AutoPVC Commands................................................................................... 59

autopvc config............................................................................................................................................60

autopvc list..................................................................................................................................................61

Config Commands .......................................................................................63

config delete ...............................................................................................................................................64

config dump................................................................................................................................................65

config flush .................................................................................................................................................66

config list.....................................................................................................................................................67

config load .................................................................................................................................................. 68

config save..................................................................................................................................................69

Connection Commands............................................................................... 71

connection appconfig ................................................................................................................................72

connection appinfo .................................................................................................................................... 74

connection applist...................................................................................................................................... 75

connection bind..........................................................................................................................................76

connection bindlist.....................................................................................................................................77

connection clean ........................................................................................................................................ 78

connection clear ......................................................................................................................................... 79

connection config.......................................................................................................................................80

connection debug....................................................................................................................................... 81

connection describe...................................................................................................................................82

ii

E-DOC-CTC-20050531-0061 v1.0

Contents

connection flush.........................................................................................................................................83

connection info...........................................................................................................................................84

connection list ............................................................................................................................................ 85

connection refresh .....................................................................................................................................86

connection stats ......................................................................................................................................... 87

connection timerclear ................................................................................................................................ 88

connection timerconfig.............................................................................................................................. 89

connection unbind .....................................................................................................................................90

CWMP Commands....................................................................................... 91

cwmp config ............................................................................................................................................... 92

cwmp traceconfig.......................................................................................................................................94

cwmp server config.................................................................................................................................... 95

Debug Commands ....................................................................................... 97

debug exec.................................................................................................................................................. 98

DHCP Commands......................................................................................... 99

dhcp client flush ....................................................................................................................................... 101

dhcp client ifadd.......................................................................................................................................102

dhcp client ifattach...................................................................................................................................103

dhcp client ifconfig...................................................................................................................................104

dhcp client ifdelete...................................................................................................................................106

dhcp client iflist ........................................................................................................................................107

dhcp client ifrelease ................................................................................................................................. 108

dhcp client ifrenew...................................................................................................................................110

dhcp client debug clear............................................................................................................................112

dhcp client debug stats............................................................................................................................ 113

dhcp client debug traceconfig.................................................................................................................114

dhcp relay add..........................................................................................................................................115

dhcp relay config......................................................................................................................................116

dhcp relay delete......................................................................................................................................117

dhcp relay flush........................................................................................................................................118

dhcp relay ifconfig.................................................................................................................................... 119

dhcp relay iflist ......................................................................................................................................... 120

dhcp relay list ...........................................................................................................................................121

dhcp relay debug stats.............................................................................................................................122

dhcp relay debug traceconfig..................................................................................................................123

dhcp server config.................................................................................................................................... 124

dhcp server flush......................................................................................................................................125

E-DOC-CTC-20050531-0061 v1.0

iii

Contents

dhcp server policy....................................................................................................................................126

dhcp server debug clear ..........................................................................................................................127

dhcp server debug stats ..........................................................................................................................128

dhcp server debug traceconfig ............................................................................................................... 130

dhcp server lease add.............................................................................................................................. 131

dhcp server lease delete.......................................................................................................................... 133

dhcp server lease flush............................................................................................................................ 134

dhcp server lease list ............................................................................................................................... 135

dhcp server option flush.......................................................................................................................... 136

dhcp server option instadd......................................................................................................................137

dhcp server option instdelete..................................................................................................................138

dhcp server option instlist....................................................................................................................... 139

dhcp server option tmpladd....................................................................................................................140

dhcp server option tmpldelete................................................................................................................ 141

dhcp server option tmpllist ..................................................................................................................... 142

dhcp server pool add ...............................................................................................................................143

dhcp server pool config...........................................................................................................................144

dhcp server pool delete ...........................................................................................................................146

dhcp server pool flush .............................................................................................................................147

dhcp server pool list................................................................................................................................. 148

dhcp server pool optadd.......................................................................................................................... 149

dhcp server pool optdelete......................................................................................................................150

dhcp server pool rtadd.............................................................................................................................151

dhcp server pool rtdelete.........................................................................................................................152

dhcp server pool ruleadd.........................................................................................................................153

dhcp server pool ruledelete.....................................................................................................................154

dhcp server rule add ................................................................................................................................ 155

dhcp server rule delete ............................................................................................................................ 156

dhcp server rule flush .............................................................................................................................. 157

dhcp server rule list.................................................................................................................................. 158

DNS Commands......................................................................................... 159

dns client config ....................................................................................................................................... 160

dns client dnsadd ..................................................................................................................................... 161

dns client dnsdelete ................................................................................................................................. 162

dns client dnslist....................................................................................................................................... 163

dns client flush .........................................................................................................................................164

dns client nslookup ..................................................................................................................................165

dns server config...................................................................................................................................... 166

dns server flush........................................................................................................................................167

dns server debug clear ............................................................................................................................ 168

iv

E-DOC-CTC-20050531-0061 v1.0

Contents

dns server debug stats.............................................................................................................................169

dns server debug spoof clear..................................................................................................................170

dns server debug spoof getaddress ....................................................................................................... 171

dns server debug spoof getflags ............................................................................................................ 172

dns server debug spoof list..................................................................................................................... 173

dns server debug spoof update ..............................................................................................................174

dns server host add.................................................................................................................................. 175

dns server host delete..............................................................................................................................176

dns server host flush................................................................................................................................ 177

dns server host list...................................................................................................................................178

dns server route add................................................................................................................................ 179

dns server route delete............................................................................................................................ 180

dns server route flush.............................................................................................................................. 181

dns server route list .................................................................................................................................182

DSD Commands......................................................................................... 183

dsd config ................................................................................................................................................. 185

dsd debug connection list .......................................................................................................................186

dsd debug proxy ......................................................................................................................................187

dsd debug recycling................................................................................................................................. 188

dsd debug stats ........................................................................................................................................ 189

dsd intercept config .................................................................................................................................190

dsd intercept stats....................................................................................................................................192

dsd syslog config .....................................................................................................................................193

dsd syslog list...........................................................................................................................................194

dsd urlfilter config....................................................................................................................................195

dsd urlfilter rule add.................................................................................................................................196

dsd urlfilter rule delete.............................................................................................................................197

dsd urlfilter rule flush............................................................................................................................... 198

dsd urlfilter rule list..................................................................................................................................199

dsd urlfilter rule modify........................................................................................................................... 200

dsd webfilter cache flush......................................................................................................................... 201

dsd webfilter cache stats .........................................................................................................................202

dsd webfilter config .................................................................................................................................203

dsd webfilter list.......................................................................................................................................204

dsd webfilter professional category add................................................................................................205

dsd webfilter professional category create ............................................................................................ 206

dsd webfilter professional category delete ............................................................................................ 207

dsd webfilter professional category flush..............................................................................................208

dsd webfilter professional category list................................................................................................. 209

dsd webfilter professional category remove......................................................................................... 210

E-DOC-CTC-20050531-0061 v1.0

v

Contents

dsd webfilter professional config ........................................................................................................... 211

dsd webfilter professional level add.......................................................................................................212

dsd webfilter professional level delete................................................................................................... 213

dsd webfilter professional level flush.....................................................................................................214

dsd webfilter professional level list........................................................................................................ 215

dsd webfilter professional level modify................................................................................................. 216

dsd webfilter professional level set........................................................................................................ 217

dsd webfilter professional rule clear ...................................................................................................... 218

dsd webfilter professional rule list ......................................................................................................... 219

dsd webfilter professional modify.......................................................................................................... 220

dsd webfilter server add.......................................................................................................................... 221

dsd webfilter server config......................................................................................................................222

dsd webfilter server delete...................................................................................................................... 223

dsd webfilter server flush........................................................................................................................ 224

dsd webfilter server list ........................................................................................................................... 225

dsd webfilter server modify .................................................................................................................... 226

dsd webfilter standard category add......................................................................................................227

dsd webfilter standard category create..................................................................................................228

dsd webfilter standard category delete..................................................................................................229

dsd webfilter standard category flush....................................................................................................230

dsd webfilter standard category list ....................................................................................................... 231

dsd webfilter standard category remove ............................................................................................... 232

dsd webfilter standard level add.............................................................................................................233

dsd webfilter standard level delete.........................................................................................................234

dsd webfilter standard level flush........................................................................................................... 235

dsd webfilter standard level list..............................................................................................................236

dsd webfilter standard level modify....................................................................................................... 237

dsd webfilter standard level set...............................................................................................

dsd webfilter standard rule clear ............................................................................................................ 239

dsd webfilter standard rule list ............................................................................................................... 240

dsd webfilter standard rule modify ........................................................................................................ 241

............... 238

DynDNS Commands.................................................................................. 243

dyndns add ...............................................................................................................................................244

dyndns delete ........................................................................................................................................... 245

dyndns flush ............................................................................................................................................. 246

dyndns list.................................................................................................................................................247

dyndns modify..........................................................................................................................................248

dyndns host add.......................................................................................................................................250

dyndns host delete...................................................................................................................................251

dyndns host flush.....................................................................................................................................252

vi

E-DOC-CTC-20050531-0061 v1.0

Contents

dyndns host list ........................................................................................................................................ 253

dyndns service list.................................................................................................................................... 254

dyndns service modify............................................................................................................................. 255

Env Commands .......................................................................................... 257

env flush....................................................................................................................................................258

env get.......................................................................................................................................................259

env list....................................................................................................................................................... 260

env set....................................................................................................................................................... 261

env unset...................................................................................................................................................262

Eth Commands........................................................................................... 263

eth ifadd ....................................................................................................................................................264

eth ifattach ................................................................................................................................................265

eth ifconfig................................................................................................................................................ 266

eth ifdelete ................................................................................................................................................267

eth ifdetach ...............................................................................................................................................268

eth iflist......................................................................................................................................................269

eth flush .................................................................................................................................................... 270

eth bridge clear......................................................................................................................................... 271

eth bridge config ...................................................................................................................................... 272

eth bridge flush ........................................................................................................................................273

eth bridge ifadd ........................................................................................................................................ 274

eth bridge ifattach .................................................................................................................................... 275

eth bridge ifconfig....................................................................................................................................276

eth bridge ifdelete .................................................................................................................................... 278

eth bridge ifdetach ...................................................................................................................................279

eth bridge iflist..........................................................................................................................................280

eth bridge macadd ................................................................................................................................... 281

eth bridge macdelete ............................................................................................................................... 282

eth bridge maclist..................................................................................................................................... 283

eth bridge mcdadd...................................................................................................................................284

eth bridge mcddelete...............................................................................................................................285

eth bridge mcdlist ....................................................................................................................................286

eth device ifconfig....................................................................................................................................287

eth device iflist..........................................................................................................................................288

eth switch group flush ............................................................................................................................. 289

eth switch group list................................................................................................................................. 290

eth switch group move............................................................................................................................ 291

eth switch mirror capture ........................................................................................................................292

E-DOC-CTC-20050531-0061 v1.0

vii

Contents

Expr Commands......................................................................................... 295

Firewall Commands................................................................................... 307

eth switch mirror egress.......................................................................................................................... 293

eth switch mirror ingress.........................................................................................................................294

expr add ....................................................................................................................................................296

expr delete ................................................................................................................................................299

expr flush ..................................................................................................................................................300

expr list......................................................................................................................................................301

expr modify...............................................................................................................................................304

firewall config........................................................................................................................................... 308

firewall clear .............................................................................................................................................310

firewall list.................................................................................................................................................311

firewall chain add.....................................................................................................................................312

firewall chain delete.................................................................................................................................313

firewall chain flush...................................................................................................................................314

firewall chain list ......................................................................................................................................315

firewall debug clear.................................................................................................................................. 316

firewall debug stats..................................................................................................................................317

firewall debug traceconfig....................................................................................................................... 318

firewall level add ...................................................................................................................................... 319

firewall level delete .................................................................................................................................. 320

firewall level flush .................................................................................................................................... 321

firewall level list........................................................................................................................................322

firewall level modify................................................................................................................................. 323

firewall level set........................................................................................................................................324

firewall rule add........................................................................................................................................ 325

firewall rule delete.................................................................................................................................... 327

firewall rule flush......................................................................................................................................328

firewall rule list.........................................................................................................................................329

firewall rule modify..................................................................................................................................331

firewall rule debug clear..........................................................................................................................332

firewall rule debug stats ..........................................................................................................................334

firewall rule debug traceconfig...............................................................................................................335

GRP Commands ......................................................................................... 337

grp config..................................................................................................................................................338

grp flush.................................................................................................................................................... 339

grp ifconfig................................................................................................................................................340

viii

E-DOC-CTC-20050531-0061 v1.0

Contents

grp iflist .....................................................................................................................................................341

grp rtlist.....................................................................................................................................................343

grp rttadd ..................................................................................................................................................344

grp rttdelete ..............................................................................................................................................345

grp rttlist....................................................................................................................................................347

grp rip bnadd............................................................................................................................................ 348

grp rip bndelete........................................................................................................................................349

grp rip bnlist .............................................................................................................................................350

grp rip config ............................................................................................................................................ 351

grp rip flush ..............................................................................................................................................353

grp rip ifconfig..........................................................................................................................................354

grp rip nbadd............................................................................................................................................ 356

grp rip nbdelete........................................................................................................................................357

grp rip nblist .............................................................................................................................................358

grp rip rtfadd............................................................................................................................................. 359

grp rip rtfdelete......................................................................................................................................... 360

grp rip rtflist..............................................................................................................................................361

grp rip show..............................................................................................................................................362

Hostmgr Commands .................................................................................363

hostmgr add ............................................................................................................................................. 364

hostmgr clear............................................................................................................................................ 366

hostmgr config ......................................................................................................................................... 367

hostmgr delete .........................................................................................................................................368

hostmgr flush ........................................................................................................................................... 369

hostmgr list...............................................................................................................................................370

IDS Commands .......................................................................................... 371

ids clear.....................................................................................................................................................372

ids config...................................................................................................................................................373

ids parser list ............................................................................................................................................374

ids parser modify .....................................................................................................................................375

ids pattern clear........................................................................................................................................ 376

ids pattern list...........................................................................................................................................377

ids pattern stats........................................................................................................................................378

ids signature list ....................................................................................................................................... 379

ids signature modify ................................................................................................................................ 380

ids threshold clear.................................................................................................................................... 381

ids threshold list.......................................................................................................................................382

ids threshold modify................................................................................................................................383

E-DOC-CTC-20050531-0061 v1.0

ix

Contents

Interface Commands ................................................................................. 385

IP Commands .............................................................................................387

interface list ..............................................................................................................................................386

ip arpadd................................................................................................................................................... 389

ip arpdelete............................................................................................................................................... 390

ip arplist .................................................................................................................................................... 391

ip config .................................................................................................................................................... 392

ip flush.......................................................................................................................................................394

ip ifadd ...................................................................................................................................................... 395

ip ifattach ..................................................................................................................................................396

ip ifconfig ..................................................................................................................................................397

ip ifdelete .................................................................................................................................................. 399

ip ifdetach ................................................................................................................................................. 400

ip iflist........................................................................................................................................................ 401

ip ifwait......................................................................................................................................................402

ip ipadd ..................................................................................................................................................... 403

ip ipconfig .................................................................................................................................................404

ip ipdelete ................................................................................................................................................. 405

ip iplist.......................................................................................................................................................406

ip mcadd ................................................................................................................................................... 407

ip mcdelete ............................................................................................................................................... 408

ip mclist.....................................................................................................................................................409

ip rtadd...................................................................................................................................................... 410

ip rtdelete.................................................................................................................................................. 411

ip rtlist ....................................................................................................................................................... 412

ip auto flush.............................................................................................................................................. 413

ip auto ifadd..............................................................................................................................................414

ip auto ifattach..........................................................................................................................................415

ip auto ifconfig.......................................................................................................................................... 416

ip auto ifdelete..........................................................................................................................................418

ip auto ifdetach.........................................................................................................................................419

ip auto iflist ...............................................................................................................................................420

ip debug httpprobe ..................................................................................................................................421

ip debug ping............................................................................................................................................ 422

ip debug sendto........................................................................................................................................ 423

ip debug stats ...........................................................................................................................................425

ip debug traceconfig ................................................................................................................................ 426

ip debug traceroute.................................................................................................................................. 427

x

E-DOC-CTC-20050531-0061 v1.0

Contents

IPQoS Commands...................................................................................... 429

ipqos config ..............................................................................................................................................430

ipqos list....................................................................................................................................................432

ipqos ef config..........................................................................................................................................433

ipqos ef list................................................................................................................................................434

ipqos ef stats.............................................................................................................................................435

ipqos meter add .......................................................................................................................................436

ipqos meter clear......................................................................................................................................437

ipqos meter config ................................................................................................................................... 438

ipqos meter delete ...................................................................................................................................440

ipqos meter flush .....................................................................................................................................441

ipqos meter list......................................................................................................................................... 442

ipqos meter start ...................................................................................................................................... 443

ipqos meter stats...................................................................................................................................... 444

ipqos meter stop ......................................................................................................................................445

ipqos queue clear.....................................................................................................................................446

ipqos queue config................................................................................................................................... 447

ipqos queue list ........................................................................................................................................ 449

ipqos queue stats .....................................................................................................................................450

IPSec Commands ....................................................................................... 451

ipsec config...............................................................................................................................................454

ipsec flush.................................................................................................................................................455

ipsec clear all ............................................................................................................................................ 456

ipsec clear sad .......................................................................................................................................... 457

ipsec clear session ...................................................................................................................................458

ipsec clear spd..........................................................................................................................................459

ipsec connection add ............................................................................................................................... 460

ipsec connection delete ...........................................................................................................................461

ipsec connection list................................................................................................................................. 462

ipsec connection modify..........................................................................................................................463

ipsec connection start..............................................................................................................................464

ipsec connection stop .............................................................................................................................. 465

ipsec connection advanced add..............................................................................................................466

ipsec connection advanced delete..........................................................................................................467

ipsec connection advanced list ...............................................................................................................468

ipsec connection advanced modify ........................................................................................................ 469

ipsec connection descriptor add.............................................................................................................471

ipsec connection descriptor delete.........................................................................................................472

ipsec connection descriptor list .............................................................................................................. 473

E-DOC-CTC-20050531-0061 v1.0

xi

Contents

ipsec connection descriptor modify .......................................................................................................474

ipsec connection dialup connect.............................................................................................................476

ipsec connection dialup disconnect........................................................................................................ 477

ipsec connection network add ................................................................................................................ 478

ipsec connection network delete ............................................................................................................479

ipsec connection network list..................................................................................................................480

ipsec connection network modify...........................................................................................................481

ipsec connection options add ................................................................................................................. 482

ipsec connection options delete ............................................................................................................. 483

ipsec connection options list...................................................................................................................484

ipsec connection options modify............................................................................................................485

ipsec debug syslog................................................................................................................................... 486

ipsec debug traceconfig...........................................................................................................................487

ipsec peer add ..........................................................................................................................................488

ipsec peer delete ......................................................................................................................................489

ipsec peer list............................................................................................................................................ 490

ipsec peer modify.....................................................................................................................................491

ipsec peer auth add.................................................................................................................................. 494

ipsec peer auth delete.............................................................................................................................. 495

ipsec peer auth list ................................................................................................................................... 496

ipsec peer auth modify ............................................................................................................................497

ipsec peer descriptor add ........................................................................................................................498

ipsec peer descriptor delete ....................................................................................................................499

ipsec peer descriptor list..........................................................................................................................500

ipsec peer descriptor modify...................................................................................................................501

ipsec peer options add.............................................................................................................................503

ipsec peer options delete......................................................................................................................... 504

ipsec peer options list..............................................................................................................................505

ipsec peer options modify.......................................................................................................................506

ipsec peer subpeer add............................................................................................................................508

ipsec peer subpeer delete........................................................................................................................509

ipsec peer subpeer list............................................................................................................................. 510

ipsec peer subpeer modify...................................................................................................................... 511

ipsec peer vpnclient add..........................................................................................................................512

ipsec peer vpnclient delete......................................................................................................................513

ipsec peer vpnclient list ...........................................................................................................................514

ipsec peer vpnclient modify ....................................................................................................................515

ipsec peer vpnserver add ........................................................................................................................516

ipsec peer vpnserver delete .................................................................................................................... 517

ipsec peer vpnserver list.......................................................................................................................... 518

ipsec peer vpnserver modify...................................................................................................................519

xii

E-DOC-CTC-20050531-0061 v1.0

Contents

ipsec peer vpnserver xauthpool add ...................................................................................................... 520

ipsec peer vpnserver xauthpool adduser............................................................................................... 521

ipsec peer vpnserver xauthpool delete .................................................................................................. 522

ipsec peer vpnserver xauthpool deluser................................................................................................523

ipsec peer vpnserver xauthpool list........................................................................................................ 524

ipsec peer vpnserver xauthpool listpool................................................................................................525

ipsec peer vpnserver xauthpool modify................................................................................................. 526

ipsec peer vpnserver xauthpool moduser .............................................................................................527

ipsec show all ...........................................................................................................................................528

ipsec show cli ...........................................................................................................................................529

ipsec show config..................................................................................................................................... 530

ipsec show sadb.......................................................................................................................................531

ipsec show sessions.................................................................................................................................532

ipsec show spd.........................................................................................................................................533

ipsec show state.......................................................................................................................................534

ipsec show stats ....................................................................................................................................... 535

ISDN Commands........................................................................................ 537

isdn flush...................................................................................................................................................538

isdn ifadd .................................................................................................................................................. 539

isdn ifattach .............................................................................................................................................. 540

isdn ifconfig .............................................................................................................................................. 541

isdn ifdelete ..............................................................................................................................................542

isdn ifdetach .............................................................................................................................................543

isdn iflist.................................................................................................................................................... 544

isdn debug clear.......................................................................................................................................545

isdn debug stats ....................................................................................................................................... 546

isdn debug traceconfig ............................................................................................................................547

isdn debug screening............................................................................................................................... 548

isdn debug vbuff ......................................................................................................................................549

isdn group addgroup ............................................................................................................................... 550

isdn group delgroup ................................................................................................................................551

isdn group addrule...................................................................................................................................552

isdn group delrule.................................................................................................................................... 553

isdn group list...........................................................................................................................................554

Label Commands .......................................................................................555

label add....................................................................................................................................................556

label delete................................................................................................................................................557

label flush..................................................................................................................................................558

E-DOC-CTC-20050531-0061 v1.0

xiii

Contents

label list..................................................................................................................................................... 559

label modify.............................................................................................................................................. 560

label chain add .........................................................................................................................................562

label chain delete .....................................................................................................................................563

label chain flush .......................................................................................................................................564

label chain list...........................................................................................................................................565

label rule add............................................................................................................................................ 566

label rule delete........................................................................................................................................568

label rule flush.......................................................................................................................................... 569

label rule list .............................................................................................................................................570

label rule modify ......................................................................................................................................571

label rule debug clear .............................................................................................................................. 572

label rule debug stats............................................................................................................................... 573

label rule debug traceconfig....................................................................................................................574

Language Commands................................................................................ 575

language config........................................................................................................................................576

language delete........................................................................................................................................ 577

language list .............................................................................................................................................578

MLP Commands ........................................................................................ 579

mlp flush ...................................................................................................................................................580

mlp import ................................................................................................................................................ 581

mlp debug export.....................................................................................................................................582

mlp debug stats........................................................................................................................................583

mlp debug traceconfig............................................................................................................................. 584

mlp privilege add .....................................................................................................................................585

mlp privilege addzone .............................................................................................................................586

mlp privilege config ................................................................................................................................. 587

mlp privilege delete .................................................................................................................................588

mlp privilege list.......................................................................................................................................589

mlp privilege removezone....................................................................................................................... 590

mlp role add..............................................................................................................................................591

mlp role addpriv.......................................................................................................................................592

mlp role config ......................................................................................................................................... 593

mlp role delete..........................................................................................................................................594

mlp role list............................................................................................................................................... 595

mlp role removepriv ................................................................................................................................596

NAT Commands......................................................................................... 597

xiv

E-DOC-CTC-20050531-0061 v1.0

Contents

nat config ..................................................................................................................................................598

nat flush .................................................................................................................................................... 599

nat ifconfig................................................................................................................................................ 600

nat iflist......................................................................................................................................................601

nat mapadd...............................................................................................................................................602

nat mapdelete...........................................................................................................................................605

nat maplist ................................................................................................................................................606

nat tmpladd...............................................................................................................................................607

nat tmpldelete........................................................................................................................................... 610

nat tmpllist................................................................................................................................................ 611

nat tmplinst............................................................................................................................................... 612

PKI Commands........................................................................................... 613

pki clearall................................................................................................................................................. 614

pki config...................................................................................................................................................615

pki crlconfig .............................................................................................................................................. 616

pki export ..................................................................................................................................................617

pki flush.....................................................................................................................................................618

pki import..................................................................................................................................................619

pki list ........................................................................................................................................................620

pki refresh .................................................................................................................................................621

pki remove ................................................................................................................................................622

pki request ................................................................................................................................................ 623

pki show.................................................................................................................................................... 624

pki cep cancel ...........................................................................................................................................625

pki cep config............................................................................................................................................ 626

pki cep list .................................................................................................................................................629

pki cep request .........................................................................................................................................630

pki cep resubmit.......................................................................................................................................631

PPP Commands.......................................................................................... 633

ppp flush ...................................................................................................................................................634

ppp ifadd................................................................................................................................................... 635

ppp ifattach............................................................................................................................................... 636

ppp ifconfig............................................................................................................................................... 637

ppp ifdelete............................................................................................................................................... 641

ppp ifdetach.............................................................................................................................................. 642

ppp iflist .................................................................................................................................................... 643

ppp ifscan..................................................................................................................................................644

ppp rtadd...................................................................................................................................................645

E-DOC-CTC-20050531-0061 v1.0

xv

Contents

PPTP Commands........................................................................................ 653

ppp rtdelete...............................................................................................................................................647

ppp relay flush..........................................................................................................................................648

ppp relay ifadd..........................................................................................................................................649

ppp relay ifdelete......................................................................................................................................650

ppp relay iflist........................................................................................................................................... 651

ppp relay sesslist......................................................................................................................................652

pptp ifadd..................................................................................................................................................654

pptp flush.................................................................................................................................................. 655

pptp list ..................................................................................................................................................... 656

pptp profadd.............................................................................................................................................657

pptp profdelete.........................................................................................................................................658

pptp proflist ..............................................................................................................................................659

Service Commands.................................................................................... 661

service host assign...................................................................................................................................662

service host config ...................................................................................................................................663

service host add .......................................................................................................................................664

service host delete ...................................................................................................................................665

service host disable.................................................................................................................................. 666

service host flush .....................................................................................................................................667

service host list.........................................................................................................................................668

service host stats...................................................................................................................................... 669

service host triggerlist .............................................................................................................................670

service host rule add................................................................................................................................ 671

service host rule delete............................................................................................................................ 672

service system ifadd ................................................................................................................................673

service system ifdelete ............................................................................................................................674

service system ipadd ............................................................................................................................... 675

service system ipdelete ...........................................................................................................................676

service system list.................................................................................................................................... 677

service system mapadd........................................................................................................................... 678

service system mapdelete....................................................................................................................... 679

service system modify............................................................................................................................. 680

Script Commands ...................................................................................... 681

script add ..................................................................................................................................................682

script delete .............................................................................................................................................. 683

script flush ................................................................................................................................................ 684

xvi

E-DOC-CTC-20050531-0061 v1.0

Contents

script list....................................................................................................................................................685

script run................................................................................................................................................... 686

SNMP Commands...................................................................................... 687

snmp config.............................................................................................................................................. 688

snmp get ...................................................................................................................................................689

snmp getnext............................................................................................................................................690

snmp walk.................................................................................................................................................691

snmp community add..............................................................................................................................692

snmp community delete.......................................................................................................................... 693

snmp community list ............................................................................................................................... 694

snmp community modify........................................................................................................................ 695

SNTP Commands....................................................................................... 697

sntp add .................................................................................................................................................... 698

sntp config ................................................................................................................................................ 699

sntp delete ................................................................................................................................................ 700

sntp flush .................................................................................................................................................. 701

sntp list......................................................................................................................................................702

Software Commands................................................................................. 703

software cleanup......................................................................................................................................704

software deletepassive ............................................................................................................................ 705

software duplicate....................................................................................................................................706

software setpassive.................................................................................................................................. 707

software switch ........................................................................................................................................ 708

software upgrade ..................................................................................................................................... 709

software version.......................................................................................................................................710

System Commands ................................................................................... 711

system config ........................................................................................................................................... 712

system flush.............................................................................................................................................. 714

system locale............................................................................................................................................715

system reboot...........................................................................................................................................717

system reset..............................................................................................................................................718

system debug autosave........................................................................................................................... 719

system debug stats .................................................................................................................................. 720

system ra config.......................................................................................................................................721

system rtc synchronize ............................................................................................................................722

system rtc settime....................................................................................................................................723

E-DOC-CTC-20050531-0061 v1.0

xvii

Contents

Systemlog Commands .............................................................................. 725

Tunnel Commands..................................................................................... 729

systemlog flush ........................................................................................................................................ 726

systemlog show .......................................................................................................................................727

systemlog send ........................................................................................................................................728

tunnel list .................................................................................................................................................. 730

tunnel gre add .......................................................................................................................................... 731

tunnel gre delete ......................................................................................................................................732

tunnel gre flush ........................................................................................................................................ 733

tunnel gre list............................................................................................................................................ 734

tunnel gre modify.....................................................................................................................................735

tunnel ipip add..........................................................................................................................................736

tunnel ipip delete...................................................................................................................................... 737

tunnel ipip flush........................................................................................................................................738

tunnel ipip list........................................................................................................................................... 739

tunnel ipip modify....................................................................................................................................740

UPnP Commands ....................................................................................... 741

upnp config...............................................................................................................................................742

upnp flush................................................................................................................................................. 743

upnp list .................................................................................................................................................... 744

User Commands ........................................................................................ 745

user add .................................................................................................................................................... 746

user config ................................................................................................................................................748

user delete ................................................................................................................................................ 749

user flush .................................................................................................................................................. 750

user list......................................................................................................................................................751

user rights.................................................................................................................................................753

Wireless Commands.................................................................................. 755

wireless ifconfig ....................................................................................................................................... 756

wireless reset............................................................................................................................................758

wireless debug stats ................................................................................................................................759

wireless macacl add.................................................................................................................................760

wireless macacl config............................................................................................................................. 761

wireless macacl delete............................................................................................................................. 762

wireless macacl flush...............................................................................................................................763

wireless macacl list .................................................................................................................................. 764

xviii

E-DOC-CTC-20050531-0061 v1.0

Contents

wireless macacl modify ........................................................................................................................... 765

wireless macacl register ..........................................................................................................................766

wireless secmode config ......................................................................................................................... 767

wireless secmode wep............................................................................................................................. 768

wireless secmode wpa-psk...................................................................................................................... 769

wireless stations list.................................................................................................................................770

wireless wds add......................................................................................................................................771

wireless wds config.................................................................................................................................. 772

wireless wds delete..................................................................................................................................773

wireless wds flush....................................................................................................................................774

wireless wds list ....................................................................................................................................... 775

wireless wds scanresults.........................................................................................................................776

Abbreviations ............................................................................................. 777

System Logging Messages ....................................................................... 781

Auto-PVC Module..................................................................................................................................... 782

Configuration Module..............................................................................................................................782

DHCP Client Module................................................................................................................................. 782

DHCP Relay Module.................................................................................................................................783

DHCP Server Module ............................................................................................................................... 783

Dyndns Module ........................................................................................................................................ 784

Firewall Module........................................................................................................................................784

LOGIN Module..........................................................................................................................................785

IPSec Module............................................................................................................................................786

ISDN Module ............................................................................................................................................ 787

Kernel Module ..........................................................................................................................................787

Linestate Module......................................................................................................................................787

NAPT Module ...........................................................................................................................................787

PPP Module...............................................................................................................................................788

PPTP Module ............................................................................................................................................ 788

RIP Module................................................................................................................................................789

Routing Module........................................................................................................................................790

Session Module........................................................................................................................................790

SNTP Module............................................................................................................................................790

Software Module......................................................................................................................................791

UPnP Module............................................................................................................................................791

Wireless Module.......................................................................................................................................791

Supported Key Names .............................................................................. 793

E-DOC-CTC-20050531-0061 v1.0

xix

Contents

Supported IP Protocols............................................................................................................................ 794

Supported TCP/UDP Port Names............................................................................................................ 795

Supported ICMP Type Names.................................................................................................................798

Supported System Logging Facilities..................................................................................................... 799

Supported System Logging Severities................................................................................................... 800

IP Precedence ........................................................................................................................................... 800

Differentiated Services Code Point (DSCP)............................................................................................801

xx

E-DOC-CTC-20050531-0061 v1.0

About this Document

About this Document

Introduction

Welcome to the SpeedTouch™ Command Line Interface (CLI) Reference Guide!

For the Service Provider, this Reference Guide aims to be a concise and practical document for creating a
customized Service Template file, based on the SpeedTouch™ CLI command set, to be used by the end user to
configure the SpeedTouch™ and computer(s).

For the fastidious user, this Reference Guide aims to be a handbook for advanced and detailed configuration and
troubleshooting of the SpeedTouch™ via its character based CLI command set.

Applicability

This CLI Reference Guide covers the CLI commands of the following Digital Subscriber Line (DSL) SpeedTouch™
products:

 R5.3.1SpeedTouch™608 WL (i) WirelessBusiness DSL Router (Software Release R5.3.1)

For readability, all are referred to as SpeedTouch™ throughout this document unless a specific variant is
concerned.

Contents

The CLI Reference Guide describes all the available CLI commands of the SpeedTouch™ per command group and
in alphabetical order.

Each command is described in a systematic manner:

 The full name of the CLI command (including the group selection).

 A short description of the CLI command, if necessary completed by a description of the possible impact on

the user and/or the SpeedTouch™.

 The syntax of the command with a description of each parameter.

 An example to demonstrate the use of the CLI command.

 A list of related CLI commands.

Other Information

For more information on the SpeedTouch™ CLI, various access methods, general manipilations to navigate
through the CLI refer to the SpeedTouch™608 WL User’s Guide.

For a description on the functional use of the CLI commands see the corresponding SpeedTouch™ configuration
guides and application notes.

E-DOC-CTC-20050531-0061 v1.0

1

About this Document

Trademarks

The following trademarks are used in this document:

 SpeedTouch™ is a trademark of THOMSON.

 Netscape and Netscape Navigator are registered trademarks of Netscape Communications Corporation.

 Windows and Internet Explorer are trademarks of Microsoft Corporation.

 Apple and MacOS are registered trademarks of Apple Computer Inc.

 UNIX is a registered trademark of UNIX System Laboratories, Inc.

 Ethernet is a trademark of Xerox Corporation.

Other products may be trademarks or registered trademarks of their respective manufacturers.

Symbols

The following symbols are used in this CLI Reference Guide:

A note provides additional information about a topic.

A tip provides an alternative method or shortcut to perform an action.

A caution warns you about potential problems or specific precautions that need to be taken.

!

Conventions

The following conventions are used to present the CLI commands:

 Vertical bars (|) separate alternative, mutually exclusive, elements.

 Square brackets [] indicate optional elements.

 Braces {} indicate a required choice.

 Braces within square brackets [{}] indicate a required choice within an optional element.

 <string> indicates that an alphanumerical string without blanks must be used.

 <quoted string> indicates that an alphanumerical string with blanks can be used. The string must be

enclosed in quotes “.

Documentation and software updates

THOMSON continuously develops new solutions, but is also committed to improve its existing products.

For suggestions regarding this document, please contact [e-mail]

For more information on THOMSON's latest technological innovations, documents and software releases, visit us
at:

www.speedtouch.com

.

2

E-DOC-CTC-20050531-0061 v1.0

ADSL Commands

ADSL Commands

Introduction

This chapter describes the commands of the adsl command group.

Contents

This chapter covers the following commands:

adsl config Show/set the Asymmetric Digital Subscriber Line (ADSL) configuration. 4

adsl info Display the ADSL statistics and information about the DSL line status. 5

E-DOC-CTC-20050531-0061 v1.0

3

ADSL Commands

adsl config

Show/set the Asymmetric Digital Subscriber Line (ADSL) configuration.

SYNTAX:

adsl config [opermode = <{multimode | multi_adsl2 | multi_readsl2

where:

| multi_adsl2plus}>]

[trace = <{disabled | enabled}>]

opermode The operational mode of the SpeedTouch™.

Choose between:

 multimode

 multi_adsl2

 multi_readsl2

 multi_adsl2plus

The default is multi_adsl2plus.

trace Enable or disable ADSL tracing.

The default is enabled.

EXAMPLE:

The example below shows the default configuration for a SpeedTouch™ ADSL/POTS variant:

=>adsl config
ADSL configuration:
opermode = multi_adsl2plus
trace = on
modemoption = 00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00
=>

OPTIONAL

OPTIONAL

4

E-DOC-CTC-20050531-0061 v1.0

ADSL Commands

adsl info

Display the ADSL statistics and information about the DSL line status.

Although the same command is used for both SpeedTouch™ ADSL/POTS and SpeedTouch™ ADSL/ISDN variants,
the command features specific output parameters and counters per variant.

SYNTAX:

adsl info

EXAMPLE (for a SpeedTouch™ ADSL/POTS variant):

=>adsl info
Modemstate : up
Operation Mode : G.992.1 Annex A
Channel Mode : interleaved
Number of resets : 1

Vendor Local Remote

Country : 0f 00
Vendor : TMMB
VendorSpecific : 0000 0000
StandardRevisionNr : 00 00

Margin [dB] : 26.0 18.0
Attenuation [dB] : 0.0 2.0
OutputPower [dBm] : 4.0 11.5

Available Bandwidth Cells/s Kbit/s

Downstream : 14490 6144
Upstream : 1509 640

Transfer statistics

Errors

Received FEC : 0
Received CRC : 0
Received HEC : 0
Transmitted FEC : 0
Transmitted CRC : 0
Tranmsitted HEC : 0

Near end failures since reset

Loss of frame: 0 failures
Loss of signal: 0 failures
Loss of power: 0 failures
Errored seconds: 0 seconds

Near end failures last 15 minutes

Loss of frame: 0 seconds
Loss of signal: 0 seconds
Loss of power: 0 seconds
Errored seconds: 0 seconds

Near end failures current day

Errored seconds: 0 seconds

Near end failures previous day

Errored seconds: 0 seconds

=>

Downstream Upstream

E-DOC-CTC-20050531-0061 v1.0

5

ADSL Commands

6

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

ATM Commands

Introduction

This chapter describes the commands of the atm command group.

Contents

This chapter covers the following commands:

atm flush Flush all Asynchronous Transfer Mode (ATM) interfaces. 9

atm ifadd Create a new ATM interface. 10

atm ifattach Attach a ATM interface. 11

atm ifconfig Configure an ATM interface. 12

atm ifdelete Delete an ATM interface. 14

atm ifdetach Detach an ATM interface. 15

atm iflist Display the ATM interfaces. 16

atm bundle add Add a new bundle of interfaces. 17

atm bundle attach Attach a bundle of interfaces. 18

atm bundle config Modify a bundle of interfaces. 19

atm bundle clear Clear the bundle statistics. 20

atm bundle delete Delete a bundle of interfaces. 21

atm bundle detach Detach a bundle of interfaces. 22

atm bundle flush Flush all bundles. 23

atm bundle ifadd Add an interface on a bundle. 24

atm bundle ifconfig Configure an interface from a bundle. 25

atm bundle ifdelete Remove an interface from a bundle. 26

atm bundle list Display the current bundles. 27

atm cac config Configure the ATM connection admission control. 28

atm cac list Display all the CAC parameters. 29

atm cac overbooking Configure ATM overbooking parameters. 30

atm debug aal5stats Display ATM Adaptation Layer 5 (AAL5) port specific ATM statistics. 31

atm debug gstats Display ATM global statistics. 32

atm debug portstats Display port specific ATM statistics. 33

atm oam config Modify the ATM Operation and Maintenance (OAM) settings. 34

atm oam list Display the ATM OAM settings. 35

atm oam modify Modify the ATM OAM data blocking mode. 36

atm oam ping Send ATM loopback cells. 37

atm oam cc list Display Continuity Check (CC) configuration. 38

atm oam cc modify Modify CC on the connection. 39

atm oam cc send Send CC activate/deactivate to connection. 40

E-DOC-CTC-20050531-0061 v1.0

7

ATM Commands

atm oam vclb add Create a loopback connection for VC. 41

atm oam vclb del Delete a loopback connection for VC. 42

atm oam vclb list List all VC loopback connections. 43

atm phonebook add Add a new phonebook entry. 44

atm phonebook autolist Show the auto PVCs. 45

atm phonebook delete Delete an existing phonebook entry. 46

atm phonebook flush Flush all the phonebook entries. 47

atm phonebook list Display the current phonebook. 48

atm qosbook add Add a new QoS book entry. 49

atm qosbook config Modify the QoS book configuration. 50

atm qosbook ctdadd Add a Connection Traffic Descriptor (CTD). 51

atm qosbook ctddelete Delete a CTD. 53

atm qosbook ctdlist Display all CTDs. 54

atm qosbook delete Delete a QoS book entry. 55

atm qosbook flush Flush all the QoS book entries. 56

atm qosbook list Display the QoS book. 57

8

E-DOC-CTC-20050531-0061 v1.0

atm flush

Flush all Asynchronous Transfer Mode (ATM) interfaces.

SYNTAX:

atm flush

ATM Commands

E-DOC-CTC-20050531-0061 v1.0

9

ATM Commands

atm ifadd

Create a new ATM interface.

SYNTAX:

atm ifadd intf = <string>

where:

intf The name for the new ATM interface.

Note If not specified, the destination parameter must be specified. In this case the

name of the destination will double as interface name.

EXAMPLE:

=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

Retry : 10 QoS : default Encaps : vcmux Fcs : disabled Ulp : mac
Connection State : connected

=>
=>atm ifadd intf = RtPPPoA_atm
=>
=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

Retry : 10 QoS : default Encaps : vcmux Fcs : disabled Ulp : mac
Connection State : connected

RtPPPoA_atm: dest : (none)

Retry : 10 QoS : default Encaps : llc Fcs : disabled Ulp : ip
Connection State : not-connected

=>

RELATED COMMANDS:

REQUIRED

atm ifdelete Delete an ATM interface.

atm iflist Display the ATM interfaces.

10

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

atm ifattach

Attach a ATM interface.

SYNTAX:

atm ifattach intf = <string>

where:

intf The name of the ATM interface to be attached. REQUIRED

EXAMPLE:

=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac
Connection State : connected

RtPPPoA_atm: dest : RtPPPoA

=>atm ifattach intf=RtPPPoA_atm
=>
=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

RtPPPoA_atm: dest : RtPPPoA

=>

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : ppp
Connection State : not-connected

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac
Connection State : connected

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : ppp
Connection State : connected

RELATED COMMANDS:

atm ifdetach Detach an ATM interface.

E-DOC-CTC-20050531-0061 v1.0

11

ATM Commands

atm ifconfig

Configure an ATM interface.

The interface to be configured must not be connected at the time of configuration. If this should be the

case, use the command :atm ifdetach before using the command :atm ifconfig.

SYNTAX:

atm ifconfig intf = <string>

where:

[dest = <string>]
[qos = <string>]
[encaps = <{llc | vcmux}>]
[retry = <number{0-65535}>]
[fcs = <{disabled | enabled | auto}>]
[ulp = <{ip | mac | ppp}>]

intf The name of the ATM interface to be configured. REQUIRED

dest The WAN destination for this ATM interface.

Typically, an ATM phonebook entry.

qos The name of the Quality of Service (QoS) book entry to apply on this ATM interface.

The default is default.

encaps The type of encapsulation to be used for this ATM interface.

Choose between:

OPTIONAL

OPTIONAL

OPTIONAL

 llc: Logical Link Control (LLC) / Sub Network Access Protocol (SNAP)

 vcmux: Virtual Channel MUltipleXing (VCMUX).

The default is llc.

fcs Enable or disable the inclusion of the Ethernet Frame Check Sequence (FCS) in the

packet header on the WAN side (only used for llc encapsulation for mac).
The default is disabled.

OPTIONAL

Note This parameter is normally left disabled.

retry A number between 0 and 65535.

Represents the number of times the SpeedTouch™ retries to set up a WAN connection
before giving up.
The default is 10.

ulp Select the Upper Layer Protocol (ULP) for this interface.

Choose between:

OPTIONAL

OPTIONAL

 ip (for a Routed IPoA interface).

 mac (for a Bridged Ethernet, Routed ETHoA, Bridged PPP over Ethernet (PPPoE),

Routed PPPoE or a PPPoE Relay interface).

 ppp (for a Routed PPP over ATM (PPPoA) interface).

The default is ip.

12

E-DOC-CTC-20050531-0061 v1.0

EXAMPLE:

=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

Retry : 10 QoS : default Encaps : llc Fcs : disabled Ulp : mac
Connection State : connected

ATM Commands

atm_8_35 : dest : atm_pvc_8_35

=>
=>atm ifconfig intf=atm_8_35 dest=atm_pvc_8_35 encaps=vcmux ulp=ppp
=>
=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

atm_8_35 : dest : RtPPPoA

=>

Retry : 10 QoS : default Encaps : llc Fcs : disabled Ulp : mac
Connection State : not-connected

Retry : 10 QoS : default Encaps : llc Fcs : disabled Ulp : mac
Connection State : connected

Retry : 10 QoS : default Encaps : vcmux Fcs : disabled Ulp : ppp
Connection State : not-connected

E-DOC-CTC-20050531-0061 v1.0

13

ATM Commands

atm ifdelete

Delete an ATM interface.

SYNTAX:

atm ifdelete intf = <string>

where:

intf The name of the ATM interface to be deleted. REQUIRED

EXAMPLE:

=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac
Connection State : connected

RtPPPoA_atm: dest : RtPPPoA

=>
=>atm ifdelete intf=RtPPPoA_atm
=>
=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

=>

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : ppp
Connection State : connected

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac
Connection State : connected

RELATED COMMANDS:

atm ifadd Create a new ATM interface.

atm iflist Display the ATM interfaces.

14

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

atm ifdetach

Detach an ATM interface.

SYNTAX:

atm ifdetach intf = <string>

where:

intf The name of the ATM interface to be detached. REQUIRED

EXAMPLE:

=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac
Connection State : connected

RtPPPoA_atm: dest : RtPPPoA

=>
=>atm ifdetach intf=RtPPPoA_atm
=>
=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

RtPPPoA_atm: dest : RtPPPoA

=>

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : ppp
Connection State : connected

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac
Connection State : connected

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : ppp
Connection State : not-connected

RELATED COMMANDS:

atm ifattach Attach a ATM interface.

E-DOC-CTC-20050531-0061 v1.0

15

ATM Commands

atm iflist

Display the ATM interfaces.

SYNTAX:

atm iflist [intf = <string>]

where:

intf The name of the ATM interface to be shown.

Note If not specified, all the ATM interfaces are shown.

EXAMPLE:

=>atm iflist
atm_0_35 : dest : atm_pvc_0_35

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac
Connection State : connected

RtPPPoA_atm: dest : RtPPPoA

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : ppp
Connection State : connected

=>atm iflist intf=RtPPPoA_atm
RtPPPoA_atm: dest : RtPPPoA

Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : ppp
Connection State : connected

=>

RELATED COMMANDS:

atm ifadd Create a new ATM interface.

atm ifdelete Delete an ATM interface.

OPTIONAL

16

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

atm bundle add

Add a new bundle of interfaces.

SYNTAX:

atm bundle add name = <string>

where:

name The name of the new bundle. REQUIRED

EXAMPLE:

=>atm bundle add name=myBundle
=>atm bundle list
myBundle: Connection state : not-connected

=>

Retry: 10 Policy: priority Propagate: disabled
TX requested bytes: 0 requested frames: 0
TX bytes: 0 frames: 0
RX bytes: 0 frames: 0

RELATED COMMANDS:

atm bundle delete Delete a bundle of interfaces.

atm bundle list Display the current bundles.

E-DOC-CTC-20050531-0061 v1.0

17

ATM Commands

atm bundle attach

Attach a bundle of interfaces.

SYNTAX:

atm bundle attach name = <string>

where:

name The name of the bundle to be attached. REQUIRED

EXAMPLE:

=>atm bundle attach name=myBundle
=>atm bundle list
myBundle: Connection state : connected

=>

Retry: 10 Policy: priority Propagate: disabled
TX requested bytes: 0 requested frames: 0
TX bytes: 0 frames: 0
RX bytes: 0 frames: 0

RELATED COMMANDS:

atm bundle detach Detach a bundle of interfaces.

18

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

atm bundle config

Modify a bundle of interfaces.

The bundle of interfaces to be configured must not be connected at the time of configuration. If this

should be the case, use the command :atm bundle detach before using the command :atm bundle
config.

SYNTAX:

atm bundle config name = <string>

[policy = <{priority | connection}>]
[propagate = <{disabled | enabled}>]
[retry = <number{0-65535}>]

where:

name The name of the bundle to be configured. REQUIRED

policy The traffic handling policy of the bundle.

Choose between:

 priority: lower layer ATM interfaces can be configured for a certain priority

range, marked packets will be sent on the corresponding interface.

 connection: all the packets of the same connection will be sent via the same

interface.

The default is priority.

propagate Enable or disable propagation of packets.

When propagation is enabled, packets are sent via the first interface configured for
that traffic. If the interface goes down, the next interface in the bundle will be used.
The default is disabled.

retry A number between 0 and 65535.

Represents the number of connection setup retries before giving up.
The default is 10.

OPTIONAL

OPTIONAL

OPTIONAL

EXAMPLE:

=>atm bundle list
myBundle: Connection state : not-connected

Retry: 10 Policy: priority Propagate: disabled
TX requested bytes: 0 requested frames: 0
TX bytes: 0 frames: 0

RX bytes: 0 frames: 0
=>atm bundle config name=myBundle policy=connection retry=15
=>atm bundle list
myBundle: Connection state : not-connected

Retry: 15 Policy: connection Propagate: disabled

TX requested bytes: 0 requested frames: 0

TX bytes: 0 frames: 0

RX bytes: 0 frames: 0
=>

E-DOC-CTC-20050531-0061 v1.0

19

ATM Commands

atm bundle clear

Clear the bundle statistics.

SYNTAX:

atm bundle clear [name = <string>]

where:

name The name of the bundle for which the statistics must be cleared.

Note If not specified, the statistics for all the bundles will be cleared.

OPTIONAL

20

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

atm bundle delete

Delete a bundle of interfaces.

SYNTAX:

atm bundle delete name = <string>

where:

name The name of the bundle to be deleted. REQUIRED

RELATED COMMANDS:

atm bundle add Add a new bundle of interfaces.

atm bundle list Display the current bundles.

E-DOC-CTC-20050531-0061 v1.0

21

ATM Commands

atm bundle detach

Detach a bundle of interfaces.

SYNTAX:

atm bundle detach intf = <string>

where:

intf The name of the bundle to be detached. REQUIRED

RELATED COMMANDS:

atm bundle attach Attach a bundle of interfaces.

22

E-DOC-CTC-20050531-0061 v1.0

atm bundle flush

Flush all bundles.

SYNTAX:

atm bundle flush

ATM Commands

E-DOC-CTC-20050531-0061 v1.0

23

ATM Commands

atm bundle ifadd

Add an interface on a bundle.

Up to 8 interfaces or (sub-)bundles can be added to one bundle.

SYNTAX:

atm bundle ifadd name = <string>

where:

name The name of the bundle to which an ATM interface must be added. REQUIRED

intf The name of the ATM interface to be added. REQUIRED

index A number between 0 and 6.

Represents the index of the ATM interface.

intf = <string>
[index = <number{0-6}>]

OPTIONAL

EXAMPLE:

=>atm bundle ifadd name=myBundle intf=myATMintf
=>atm bundle list
myBundle: Connection state : not-connected

=>

Retry: 15 Policy: connection

TX requested bytes: 0 requested frames: 0

TX bytes: 0 frames: 0

RX bytes: 0 frames: 0

Interface: myATMintf State: enabled Selector: 0-15

TX bytes: 0 frames: 0
RX bytes: 0 frames: 0
RX discarded bytes: 0 discarded frames: 0
Disconnects: 0

RELATED COMMANDS:

atm bundle ifdelete Remove an interface from a bundle.

24

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

atm bundle ifconfig

Configure an interface from a bundle.

The interface to be configured must not be connected at the time of configuration. If this should be the

case, use the command :atm bundle ifdetach before using the command :atm bundle ifconfig.

SYNTAX:

atm bundle ifconfig name = <string>

intf = <string>
[state = <{disabled | enabled}>]
[low = <number{0-15}>]
[high = <number{0-15}>]

where:

name The name of the bundle from which an ATM interface must be configured. REQUIRED

intf The name of the ATM interface to be configured. REQUIRED

state Enable or disable the ATM interface.

The default is enabled.

low A number between 0 and 15.

Represents the low selector value.

Note This parameter must only be configured when the policy of the bundle is set

to priority (see “ atm bundle config” on page 19).

high A number between 0 and 15.

Represents the high selector value.

Note This parameter must only be configured when the policy of the bundle is set

to priority (see “ atm bundle config” on page 19).

OPTIONAL

OPTIONAL

OPTIONAL

E-DOC-CTC-20050531-0061 v1.0

25

ATM Commands

atm bundle ifdelete

Remove an interface from a bundle.

SYNTAX:

atm bundle ifdelete name = <string>

where:

name The name of the bundle from which an ATM interface must be removed. REQUIRED

intf The name of the ATM interface to be removed. REQUIRED

EXAMPLE:

intf = <string>

=>atm bundle iflist
Test : dest : (none)

=>atm bundle ifdelete intf=Test
=>atm bundle iflist

=>

Retry : 10 QoS : default Encaps : llc Fcs : off Ulp : ip
Connection State : not-connected

RELATED COMMANDS:

atm bundle ifadd Add an interface on a bundle.

26

E-DOC-CTC-20050531-0061 v1.0

atm bundle list

Display the current bundles.

SYNTAX:

atm bundle list

EXAMPLE:

=>atm bundle list
Test : Connection state : not-connected

Retry: 10 Policy: priority

TX requested bytes: 0 requested frames: 0

TX bytes: 0 frames: 0

RX bytes: 0 frames: 0

Interface: Test State: enabled Selector: 0-15

TX bytes: 0 frames: 0
RX bytes: 0 frames: 0
RX discarded bytes: 0 discarded frames: 0
Disconnects: 0

=>

ATM Commands

RELATED COMMANDS:

atm bundle add Add a new bundle of interfaces.

atm bundle delete Delete a bundle of interfaces.

E-DOC-CTC-20050531-0061 v1.0

27

ATM Commands

atm cac config

Configure the ATM connection admission control.

SYNTAX:

atm cac config config port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number>

where:

config port The port for which CAC is configured. REQUIRED

state Enable/disable CAC for an ATM port. REQUIRED

EXAMPLE:

state = <{disabled|enabled}>

{Administrator}=>atm cac config
port = dsl0
state = enabled
:atm cac config port=dsl0 state=enabled
{Administrator}=>

RELATED COMMANDS:

atm cac list Display all the CAC parameters.

atm cac overbooking Configure ATM overbooking parameters.

28

E-DOC-CTC-20050531-0061 v1.0

atm cac list

Display all the CAC parameters.

SYNTAX:

atm cac list

EXAMPLE:

{Administrator}[atm cac]=>list
CAC: port: dsl0 state: enabled
CAC: port: dsl1 state: enabled
CAC: port: atm2 state: enabled
CAC: port: aal5 state: disabled
CAC: port: atm5 state: disabled
Overbooking: realtime: 0% non-realtime: 0%.
{Administrator}[atm cac]=>

ATM Commands

RELATED COMMANDS:

atm cac config Configure the ATM connection admission control.

atm cac overbooking Configure ATM overbooking parameters.

E-DOC-CTC-20050531-0061 v1.0

29

ATM Commands

atm cac overbooking

Configure ATM overbooking parameters.

SYNTAX:

atm cac overbooking rt = <number{0-1000}>

where:

nrt = <number{0-1000}>

rt A number between 0 and 1000.

The realtime overbooking percentage.

nrt A number between 0 and 1000.

The non-realtime overbooking percentage.

EXAMPLE:

{Administrator}[atm cac]=>overbooking rt 20 nrt 500
{Administrator}[atm cac]=>list
CAC: port: dsl0 state: enabled
CAC: port: dsl1 state: enabled
CAC: port: atm2 state: enabled
CAC: port: aal5 state: disabled
CAC: port: atm5 state: disabled
Overbooking: realtime: 20% non-realtime: 500%.
{Administrator}[atm cac]=>

RELATED COMMANDS:

atm cac config Configure the ATM connection admission control.

atm cac list Display all the CAC parameters.

REQUIRED

REQUIRED

30

E-DOC-CTC-20050531-0061 v1.0

atm debug aal5stats

Display ATM Adaptation Layer 5 (AAL5) port specific ATM statistics.

SYNTAX:

atm debug aal5stats port = <{dsl0} or number>

vpi = <number{0-15}>
[vci = <number{0-511}>]
[clear = <{disabled | enabled}>]

where:

ATM Commands

port The port number for which statistics will be retrieved.

Choose between:

REQUIRED

 DSL0

Or specify a port number (dsl0 has port number 0).

vpi A number between 0 and 15.

Represents the Virtual Path Identifier (VPI) number for which statistics will be retrieved.

vci A number between 0 and 511.

Represents the Virtual Channel Identifier (VCI) number for which statistics will be
retrieved.

clear Enable or disable clearing of the statistics after request. OPTIONAL

REQUIRED

OPTIONAL

RELATED COMMANDS:

atm debug gstats Display ATM global statistics.

atm debug portstats Display port specific ATM statistics.

E-DOC-CTC-20050531-0061 v1.0

31

ATM Commands

atm debug gstats

Display ATM global statistics.

SYNTAX:

atm debug gstats [clear = <{disabled | enabled}>]

where:

clear Enable or disable clearing of the statistics after request. OPTIONAL

EXAMPLE:

{admin}[atm debug]=>gstats
# of received octets = 1802.
# of transmitted octets = 4346.
# of received cells = 34.
# of transmitted cells = 82.
# of unknown cells = 0.
# of errors on the input = 0.
# of errors on output = 0.
{admin}[atm debug]=>

RELATED COMMANDS:

atm debug aal5stats Display ATM Adaptation Layer 5 (AAL5) port specific ATM statistics.

atm debug portstats Display port specific ATM statistics.

32

E-DOC-CTC-20050531-0061 v1.0

atm debug portstats

Display port specific ATM statistics.

SYNTAX:

atm debug portstats port = <{dsl0} or number>

[clear = <{disabled | enabled}>]

where:

ATM Commands

port The port number for which statistics will be retrieved.

Choose between:

REQUIRED

 DSL0

Or specify a port number (dsl0 has port number 0).

clear Enable or disable clearing of the statistics after request. OPTIONAL

EXAMPLE:

=>atm debug portstats port=dsl0
# of received octets = 1961.
# of transmitted octets = 4717.
# of received cells = 37.
# of transmitted cells = 89.
# of unknown cells = 0.
# of errors on the input = 0.
# of errors on output = 0.
=>

RELATED COMMANDS:

atm debug aal5stats Display ATM Adaptation Layer 5 (AAL5) port specific ATM statistics.

atm debug gstats Display ATM global statistics.

E-DOC-CTC-20050531-0061 v1.0

33

ATM Commands

atm oam config

Modify the ATM Operation and Maintenance (OAM) settings.

SYNTAX:

atm oam config [clp = <number{0-1}>]

where:

[loopbackid = <string>]

clp A number (0 or 1).

Represents the Cell Loss Priority (CLP) bit value of the OAM cells.
The default is 1.

loopbackid A hexadecimal string.

Represents the loopback ID for processing of segment loopback cells.
The default is 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a.

RELATED COMMANDS:

atm oam list Display the ATM OAM settings.

atm oam modify Modify the ATM OAM data blocking mode.

atm oam ping Send ATM loopback cells.

OPTIONAL

OPTIONAL

34

E-DOC-CTC-20050531-0061 v1.0

atm oam list

Display the ATM OAM settings.

SYNTAX:

atm oam list

EXAMPLE:

=>atm oam list

OAM config dump

-------------------

CLP bit value : 1
Loopback id : 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a

OAM data blocking mode

--------------------------

Port dsl0: blocking
Port dsl1: blocking
Port atm2: blocking
Port atm3: blocking
Port aal5: blocking
Port atm5: blocking

=>

ATM Commands

RELATED COMMANDS:

atm oam config Modify the ATM Operation and Maintenance (OAM) settings.

atm oam modify Modify the ATM OAM data blocking mode.

atm oam ping Send ATM loopback cells.

E-DOC-CTC-20050531-0061 v1.0

35

ATM Commands

atm oam modify

Modify the ATM OAM data blocking mode.

SYNTAX:

atm oam modify port = <{dsl0} or number>

where:

blocking = <{disabled | enabled}>

port The port for which OAM blocking is configured.

Choose between:

 DSL0

Or specify a port number (dsl0 has port number 0).

blocking Enable or disable the OAM data blocking mode on this port.

The default is enabled.

EXAMPLE:

=>atm oam list

OAM config dump

-------------------

--------------------------

=>atm oam modify port=dsl1 blocking=disabled
=>:atm oam list

-------------------

--------------------------

=>

CLP bit value : 1
Loopbackid :6a6a6a6a6a6a6a6a6a6a6a6a6a6a6a6a

OAM data blocking mode

Port dsl0: blocking
Port dsl1: blocking
Port atm2: blocking
Port atm3: blocking
Port aal5: blocking
Port atm5: blocking

OAM config dump

CLP bit value : 1
Loopbackid :6a6a6a6a6a6a6a6a6a6a6a6a6a6a6a6a

OAM data blocking mode

Port dsl0: blocking
Port dsl1: non blocking
Port atm2: blocking
Port atm3: blocking
Port aal5: blocking
Port atm5: blocking

REQUIRED

REQUIRED

RELATED COMMANDS:

atm oam config Modify the ATM Operation and Maintenance (OAM) settings.

atm oam list Display the ATM OAM settings.

atm oam ping Send ATM loopback cells.

36

E-DOC-CTC-20050531-0061 v1.0

atm oam ping

Send ATM loopback cells.

SYNTAX:

atm oam ping dest = <string>

[count = <number{1-1000000}>]
[interval = <number{100-1000000}>]

where:

ATM Commands

dest The destination address for the request.

This can be any ATM phonebook entry.

count A number between 1 and 1000000.

Represents the number of pings to send.

interval A number between 100 and 1000000 (milliseconds).

Represents the interval between packets.

EXAMPLE:

=>atm oam ping dest=atm_ph_8_35 count=10 interval=1000
loopback: successful, sequence: 1 time: 37890 usec
loopback: successful, sequence: 2 time: 39118 usec
loopback: successful, sequence: 3 time: 39116 usec
loopback: successful, sequence: 4 time: 39187 usec
loopback: successful, sequence: 5 time: 38605 usec
loopback: successful, sequence: 6 time: 38764 usec
loopback: successful, sequence: 7 time: 38752 usec
loopback: successful, sequence: 8 time: 38813 usec
loopback: successful, sequence: 9 time: 38848 usec
loopback: successful, sequence: 10 time: 38941 usec

--- loopback statistics --­10 loopbacks transmitted, 10 successful, 0% loss, time 1390 ms
rtt min/avg/max = 37890/38803/39187
=>

REQUIRED

OPTIONAL

OPTIONAL

RELATED COMMANDS:

atm oam config Modify the ATM Operation and Maintenance (OAM) settings.

atm oam list Display the ATM OAM settings.

atm oam modify Modify the ATM OAM data blocking mode.

E-DOC-CTC-20050531-0061 v1.0

37

ATM Commands

atm oam cc list

Display Continuity Check (CC) configuration.

SYNTAX:

atm oam cc list

EXAMPLE:

=>atm oam cclist
PORT = 0 VPI = 15 VCI = 16 End2End Mode = Auto Segment Mode = Auto
PORT = 0 VPI = 0 VCI = 35 End2End Mode = Auto Segment Mode = Auto
PORT = 0 VPI = 8 VCI = 35 End2End Mode = Auto Segment Mode = Auto
PORT = 0 VPI = 0 VCI = 16 End2End Mode = Auto Segment Mode = Auto
=>

RELATED COMMANDS:

atm oam cc modify Modify CC on the connection.

atm oam cc send Send CC activate/deactivate to connection.

38

E-DOC-CTC-20050531-0061 v1.0

atm oam cc modify

Modify CC on the connection.

SYNTAX:

atm oam modify port = <{dsl0} or number>

vpi = <number{0-15}>
[vci = <number{0-511}>]
[transmit = <{disabled | enabled}>]
[receive = <{disabled | enabled}>]
[auto = <{disabled | enabled}>]
[span = <{segment | end2end}>]

where:

ATM Commands

port The ATM port number.

Choose between:

REQUIRED

 DSL0

Or specify a port number (dsl0 has port number 0).

vpi A number between 0 and 15.

Represents the VPI.

vci A number between 0 and 511.

Represents the VCI.

REQUIRED

OPTIONAL

Note For a Virtual Path (VP) cross-connection, use 0 or do not specify.

transmit Enable or disable transmission of CC cells. OPTIONAL

receive Enable or disable loss of continuity. OPTIONAL

auto Enable or disable remote CC activation/deactivation. OPTIONAL

span Select the CC span.

Choose between:

OPTIONAL

 end2end: monitoring occurs on the entire VC between two ATM end stations.

 segment: monitoring occurs on a VC segment between the SpeedTouch™ and a

first-hop ATM switch.

RELATED COMMANDS:

atm oam cc list Display Continuity Check (CC) configuration.

atm oam cc send Send CC activate/deactivate to connection.

E-DOC-CTC-20050531-0061 v1.0

39

ATM Commands

atm oam cc send

Send CC activate/deactivate to connection.

SYNTAX:

atm oam cc send port = <{dsl0} or number>

where:

vpi = <number{0-15}>
[vci = <number{0-511}>]
[span = <{segment | end2end}>]
[action = <{activate | deactivate}>]
[direction = <{source | sink | both}>]

port The ATM port number.

Choose between:

 DSL0.

Or specify a port number (dsl0 has port number 0).

vpi A number between 0 and 15.

Represents the VPI.

vci A number between 0 and 511.

Represents the VCI.

Note For a VP cross-connection, use 0 or do not specify.

span Select the CC span.

Choose between:

 end2end: monitoring occurs on the entire VC between two ATM end stations.

 segment: monitoring occurs on a VC segment between the SpeedTouch™ and a

first-hop ATM switch.

action Activate or deactivate CC.

The default is deactivate.

direction Indicates the direction of CC activity.

Choose between:

 source

 sink

 both.

The default is both.

REQUIRED

REQUIRED

OPTIONAL

OPTIONAL

OPTIONAL

OPTIONAL

RELATED COMMANDS:

atm oam cc list Display Continuity Check (CC) configuration.

atm oam cc modify Modify CC on the connection.

40

E-DOC-CTC-20050531-0061 v1.0

atm oam vclb add

Create a loopback connection for VC.

SYNTAX:

atm oam vclb add port = <{dsl0} or number>

vpi = <number{0-15}>
[vci = <number{0-511}>]

where:

ATM Commands

port The ATM port number.

Choose between:

 DSL0

Or specify a port number (dsl0 has port number 0).

vpi A number between 0 and 15.

Represents the VPI.

vci A number between 0 and 511.

Represents the VCI.

Note For a VP cross-connection, use 0 or do not specify.

EXAMPLE:

=>atm oam vclb add port=dsl0 vpi=0 vci=36
=>atm oam vclb list
PORT = 0 VPI=0VCI= 36
=>atm oam vclb add port=dsl1 vpi=0 vci=37
=>atm oam vclb list
PORT = 0 VPI=0VCI= 36
PORT = 1 VPI=0VCI= 37
=>

RELATED COMMANDS:

REQUIRED

REQUIRED

OPTIONAL

atm oam vclb del Delete a loopback connection for VC.

atm oam vclb list List all VC loopback connections.

E-DOC-CTC-20050531-0061 v1.0

41

ATM Commands

atm oam vclb del

Delete a loopback connection for VC.

SYNTAX:

atm oam vclb del port = <{dsl0} or number>

where:

vpi = <number{0-15}>
[vci = <number{0-511}>]

port The ATM port number.

Choose between:

 DSL0

Or specify a port number (dsl0 has port number 0).

vpi A number between 0 and 15.

Represents the VPI.

vci A number between 0 and 511.

Represents the VCI.

Note For a VP cross-connection, use 0 or do not specify.

EXAMPLE:

=>atm oam vclb list
PORT = 0 VPI=0VCI= 36
PORT = 1 VPI=0VCI= 37
=>atm oam vclb del port=dsl1 vpi=0 vci=37
=>atm oam vclb list
PORT = 0 VPI=0VCI= 36
=>

RELATED COMMANDS:

atm oam vclb add Create a loopback connection for VC.

atm oam vclb list List all VC loopback connections.

REQUIRED

REQUIRED

OPTIONAL

42

E-DOC-CTC-20050531-0061 v1.0

atm oam vclb list

List all VC loopback connections.

SYNTAX:

atm oam vclb list

EXAMPLE:

=>atm oam vclb list
PORT = 0 VPI=0VCI= 36
PORT = 1 VPI=0VCI= 37
=>

RELATED COMMANDS:

ATM Commands

atm oam vclb add Create a loopback connection for VC.

atm oam vclb del Delete a loopback connection for VC.

E-DOC-CTC-20050531-0061 v1.0

43

ATM Commands

atm phonebook add

Add a new phonebook entry.

SYNTAX:

atm phonebook add name = <string>

where:

addr = <atmchannel : PVC syntax is [port.]vpi.vci

port=dsl0 | ...>

name The name of the new phonebook entry.

This name can be freely chosen, however two limitations apply:

 The name of a phonebook entry intended for the Relayed PPPoA (PPPoA-to-PPTP

Relaying) packet service may not start with capital P or capital T

 The name of a phonebook entry intended for the PPP-to-DHCP spoofing packet

service must start with DHCP (for example DHCP_Spoof01).

addr The ATM address for this destination.

It is composed of a VPI and a VCI identifying ATM virtual channels. In most cases the
values are provided by the Service Provider.
Accepted VPI: a number between 0 and 15.
Accepted VCI: a number between 0 and 511.

EXAMPLE:

=>atm phonebook list
Name Use Address
atm_pvc_0_35 1 0.35
=>atm phonebook add name=RtPPPoA addr=8.35
=>atm phonebook list
Name Use Address
atm_pvc_0_35 1 0.35
RtPPPoA 0 8.35
=>

REQUIRED

REQUIRED

RELATED COMMANDS:

atm phonebook delete Delete an existing phonebook entry.

atm phonebook list Display the current phonebook.

44

E-DOC-CTC-20050531-0061 v1.0

atm phonebook autolist

Show the auto PVCs.

Auto PVCs are only shown if they are supported by the Central Office DSLAM.

SYNTAX:

atm phonebook autolist

EXAMPLE:

=>atm phonebook autolist

8.35
=>

ATM Commands

RELATED COMMANDS:

atm phonebook list Display the current phonebook.

E-DOC-CTC-20050531-0061 v1.0

45

ATM Commands

atm phonebook delete

Delete an existing phonebook entry.

This command is only applicable for phonebook entries that are not used (in other words, not configured
for any packet service).

SYNTAX:

atm phonebook delete name = <string>

where:

name The name of the phonebook entry to be deleted.

Tip Use the command :atm phonebook li st to check whether the entry is in

Use=1

use (

) or not (

Use=0

).

EXAMPLE:

=>atm phonebook list
Name Use Address
atm_pvc_0_35 1 0.35
RtPPPoA 0 8.35
=>atm phonebook delete name=RtPPPoA
=>atm phonebook list
Name Use Address
atm_pvc_0_35 1 0.35
=>

RELATED COMMANDS:

atm phonebook add Add a new phonebook entry.

atm phonebook list Display the current phonebook.

REQUIRED

46

E-DOC-CTC-20050531-0061 v1.0

atm phonebook flush

Flush all the phonebook entries.

1. Phonebook entries that are in use, cannot be flushed.

2. This command does not impact previously saved configurations.

SYNTAX:

atm phonebook flush

EXAMPLE:

=>atm phonebook list
Name Use Address
atm_pvc_0_35 1 0.35
RtPPPoA 0 8.35
=>
=>atm phonebook flush
Some phonebook entries are still in use. Entries that are in use cannot be deleted.
=>
=>atm phonebook list
Name Use Address
atm_pvc_0_35 1 0.35
=>

ATM Commands

E-DOC-CTC-20050531-0061 v1.0

47

ATM Commands

atm phonebook list

Display the current phonebook.

SYNTAX:

atm phonebook list

EXAMPLE:

=>atm phonebook list
Name Use Address
atm_pvc_0_35 1 0.35
RtPPPoA 0 8.35
=>

RELATED COMMANDS:

atm phonebook add Add a new phonebook entry.

atm phonebook autolist Show the auto PVCs.

atm phonebook delete Delete an existing phonebook entry.

48

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

atm qosbook add

Add a new QoS book entry.

SYNTAX:

atm qosbook add name = <string>

[txctd = <string>]
[rxctd = <string>]

where:

name The name of the new QoS entry. REQUIRED

txctd The name of the Conformance Traffic Descriptor (CTD) for the transmit (upstream)

direction.

rxctd The name of the CTD for the receive (downstream) direction. OPTIONAL

OPTIONAL

EXAMPLE:

=>atm qosbook list
Name Ref Tx CTD Rx CTD
default 3 default default
=>

RELATED COMMANDS:

atm qosbook delete Delete a QoS book entry.

atm qosbook list Display the QoS book.

E-DOC-CTC-20050531-0061 v1.0

49

ATM Commands

atm qosbook config

Modify the QoS book configuration.

SYNTAX:

atm qosbook config [format = <{bytes | cells}>]

where:

format The input/output format of the QoS book.

Choose between:

OPTIONAL

 bytes: the output is shown in Kbits or bytes.

 cells: the output is shown in cps or cells.

The default is bytes.

EXAMPLE:

=>atm qosbook ctdlist
Name Ref Conf Peak Sust Burst Minrate Frame Cdvt RT FD

default 2 UBR linerate 0 0 0 0 0 disabled disabled
=>atm qosbook config format=cells
=>atm qosbook ctdlist
Name Ref Conf Peak Sust Burst Minrate Frame Cdvt RT FD

default 2 UBR linerate 0 0 0 0 0 disabled disabled
=>

(Kbits) (Kbits) (bytes) (Kbits) (bytes)

(cps) (cps) (cells) (cps) (cells)

50

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

atm qosbook ctdadd

Add a Connection Traffic Descriptor (CTD).

SYNTAX:

atm qosbook ctdadd name = <string>

conformance = <{UBR | CBR | VBR }>
[peakrate = <number{0-27786}>]
[sustrate = <number{0-27786}
[maxburst = <number{0-12240}>]
[realtime = <{enabled | disabled}>]

where:

name The name of the new CTD. REQUIRED

conformance The ATM service conformance definition. REQUIRED

peakrate A number between 0 and 27786.

Represents the peak rate (in kilobits per second).
The default is 0 (indicates linerate for UBR).

sustrate A number between 0 and 27786.

Represents the sustainable rate (in kilobits per second) (VBR only).
The default is 0.

maxburst A number between 48 and 12240.

Represents the maximum burst size (in bytes) (VBR or GFR).
The default is 0.

realtime Enable or disable realtime traffic (VBR only).

The default is disabled.

OPTIONAL

OPTIONAL

OPTIONAL

OPTIONAL

EXAMPLE:

=>atm qosbook ctdadd name=High conformance=CBR peakrate=27786
=>atm qosbook ctdlist
Name Ref Conf Peak Sust Burst Minrate Frame Cdvt RT FD

(Kbits) (Kbits) (bytes) (Kbits) (bytes)

default 2 UBR linerate 0 0 0 0 0 disabled disabled
High 0 CBR 27786 0 0 0 0 0 disabled disabled
=>

E-DOC-CTC-20050531-0061 v1.0

51

ATM Commands

IMPORTANT NOTE:

The SpeedTouch™ always rounds up specified burst sizes to a multiple of 48 bytes (a multiple of ATM cells).

Example:

In the example below a burst size of 100 bytes is specified (maxburst=100). The SpeedTouch™ will round up the
burst size to the closest matching multiple of 48 bytes, as can be seen when displaying the profile via the

command :atm qosbook ctdlist (burst=144).

=>atm qosbook ctdadd name=Medium conformance=VBR peakrate=27786 sustrate=20000 maxburst=100
=>atm qosbook ctdlist
Name Ref Conf Peak Sust Burst Minrate Frame Cdvt RT FD

default 2 UBR linerate 0 0 0 0 0 disabled disabled
Medium 0 VBR 27786 20000 144 0 0 0 disabled disabled
=>

RELATED COMMANDS:

atm qosbook ctddelete Delete a CTD.

atm qosbook ctdlist Display all CTDs.

(Kbits) (Kbits) (bytes) (Kbits) (bytes)

52

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

atm qosbook ctddelete

Delete a CTD.

SYNTAX:

atm qosbook ctddelete name = <string>

[force = <{disabled | enabled}>]

where:

name The name of the CTD entry to be deleted. REQUIRED

force Enable or disable to force delete the entry even when it is still in use.

The default is disabled.

EXAMPLE:

OPTIONAL

=>atm qosbook ctdlist
Name Ref Conf Peak Sust Burst Minrate Frame Cdvt RT FD

default 2 UBR linerate 0 0 0 0 0 disabled disabled
High 0 CBR 27786 0 0 0 0 0 disabled disabled
=>atm qosbook ctddelete name=High
=>atm qosbook ctdlist
Name Ref Conf Peak Sust Burst Minrate Frame Cdvt RT FD

default 2 UBR linerate 0 0 0 0 0 disabled disabled
=>

(Kbits) (Kbits) (bytes) (Kbits) (bytes)

(Kbits) (Kbits) (bytes) (Kbits) (bytes)

RELATED COMMANDS:

atm qosbook ctdadd Add a Connection Traffic Descriptor (CTD).

atm qosbook ctdlist Display all CTDs.

E-DOC-CTC-20050531-0061 v1.0

53

ATM Commands

atm qosbook ctdlist

Display all CTDs.

SYNTAX:

atm qosbook ctdlist

EXAMPLE:

=>atm qosbook ctdlist
Name Ref Conf Peak Sust Burst Minrate Frame Cdvt RT FD

default 2 UBR linerate 0 0 0 0 0 disabled disabled
High 0 CBR 27786 0 0 0 0 0 disabled disabled
=>

(Kbits) (Kbits) (bytes) (Kbits) (bytes)

RELATED COMMANDS:

atm qosbook ctdadd Add a Connection Traffic Descriptor (CTD).

atm qosbook ctddelete Delete a CTD.

54

E-DOC-CTC-20050531-0061 v1.0

ATM Commands

atm qosbook delete

Delete a QoS book entry.

SYNTAX:

atm qosbook delete name = <string>

[force = <{disabled | enabled}>]

where:

name The name of the QoS book entry to be deleted. REQUIRED

force Enable or disable to force delete the entry even when it is still in use.

The default is disabled.

EXAMPLE:

OPTIONAL

=>atm qosbook list
Name Ref Type TX peak sust burst RX peak sust burst framediscard

default 3 ubr linerate 0 0 linerate 0 0 disabled
TestVBR 0 vbr-nrt 1500 1000 144 1500 1000 144 enabled
=>atm qosbook delete name=TestVBR
=>atm qosbook list
Name Ref Type TX peak sust burst RX peak sust burst framediscard

default 3 ubr linerate 0 0 linerate 0 0 disabled
=>

(Kbits) (Kbits) (bytes) (Kbits) (Kbits) (bytes)

(Kbits) (Kbits) (bytes) (Kbits) (Kbits) (bytes)

RELATED COMMANDS:

atm qosbook add Add a new QoS book entry.

atm qosbook list Display the QoS book.

E-DOC-CTC-20050531-0061 v1.0

55

ATM Commands

atm qosbook flush

Flush all the QoS book entries.

The flush command does not impact previously saved configurations.

SYNTAX:

atm qosbook flush

56

E-DOC-CTC-20050531-0061 v1.0

atm qosbook list

Display the QoS book.

SYNTAX:

atm qosbook list

EXAMPLE:

=>atm qosbook list
Name Ref Type TX peak sust burst RX peak sust burst framediscard

(Kbits) (Kbits) (bytes) (Kbits) (Kbits) (bytes)
default 3 ubr linerate 0 0 linerate 0 0 disabled
TestVBR 0 vbr-nrt 1500 1000 144 1500 1000 144 enabled
=>

ATM Commands

RELATED COMMANDS:

atm qosbook add Add a new QoS book entry.

atm qosbook delete Delete a QoS book entry.

E-DOC-CTC-20050531-0061 v1.0

57

ATM Commands

58

E-DOC-CTC-20050531-0061 v1.0

AutoPVC Commands

AutoPVC Commands

Introduction

This chapter describes the commands of the autopvc command group.

Contents

This chapter covers the following commands:

autopvc config Configure autopvc. 60

autopvc list Show the retrieved information. 61

E-DOC-CTC-20050531-0061 v1.0

59

AutoPVC Commands

autopvc config

Configure autopvc.

SYNTAX:

autopvc config [mode = <{pseudo | passive | active}>]

where:

[type = <{bridge | pppoerelay | ipoa | ethoa | pppoa | pppoe}>]
[overwrite = <{disabled | enabled}>]
[peakrate = <number{0-27786}>]

mode Select the autopvc mode:

 pseudo: only pseudo-ILMI (VP/VC 15/16) is enabled. When the connection

parameters are written to the MIB, this information is displayed on CLI or web
interface but these parameters are not used for configuration.

 passive: both ILMI (VP/VC 0/16) and pseudo-ILMI (VP/VC 15/16) are enabled.

When the connection parameters are written to the MIB, this information is
displayed on CLI or web interface but these parameters are not used for
configuration.

 active: both ILMI (VP/VC 0/16) and pseudo-ILMI (VP/VC 15/16) are enabled.

When the connection parameters are written to the MIB, these parameters are
used to configure phonebook entries, qosbook profiles and bind bridge or
PPPoE interfaces on top.

The default is passive.

type Select the type of autopvc.

Choose between:

 bridge

 pppoerelay: an ETHoA interface will be created, will be bound to the ILMI

Permanent Virtual Channel (PVC) and will be added to the PPPoE relay as relay
port.

 ipoa

 ethoa

 pppoa

 pppoe.

overwrite Enable or disable UBR peak rate overwrite.

The default is disabled.

peakrate A number between 0 and 27786.

Represents the UBR peak rate (in kilobits per second).
The default is 0 (indicates the linerate).

OPTIONAL

OPTIONAL

OPTIONAL

OPTIONAL

EXAMPLE:

=>autopvc config
Autopvc mode : passive
Autopvc type :
Autopvc standard: unknown
Autopvc pseudo : unknown
UBR overwrite : disabled
UBR peak rate : linerate
=>

60

E-DOC-CTC-20050531-0061 v1.0

autopvc list

Show the retrieved information.

SYNTAX:

autopvc list [table = <{Port | AtmLayer | Vpc | Vcc | Address

| AddressRegistrationAdmin | AtmServiceType
| AtmServiceConnectionInfo | AAL1Profile |
| AAL34Profile | AAL5Profile | AAL2CommonProfile
| AAL2TrunkingProfile | AAL2LESProfile
| AtmServiceConnInfoExtension |
| AtmServiceTypeExtension | AAL5ProfileExtension}>]

where:

AutoPVC Commands

table Select the autopvc table for which the information must be shown.

Choose between:

 Port

 AtmLayer

 Vpc

 Vcc

 Address

 AddressRegistrationAdmin

 AtmServiceType

 AtmServiceConnectionInfo

 AAL1Profile

 AAL34Profile

 AAL5Profile

 AAL2CommonProfile

 AAL2TrunkingProfile

 AAL2LESProfile

 AtmServiceConnInfoExtension

 AtmServiceTypeExtension

 AAL5ProfileExtension.

OPTIONAL

EXAMPLE:

=>autopvc list
Address Type BestEff Par1 Par2 Par3 Par4 Par5

8.35 ubr Enabled Tx: 451 0 0 0 0

Rx: 7923 0 0 0 0

=>

E-DOC-CTC-20050531-0061 v1.0

61

AutoPVC Commands

62

E-DOC-CTC-20050531-0061 v1.0

Config Commands

Config Commands

Introduction

This chapter describes the commands of the config command group.

Contents

This chapter covers the following commands:

config delete Delete a user configuration file. 64

config dump Show the saved configuration file. 65

config flush Flush the loaded configuration. 66

config list Show the current configuration set. 67

config load Load complete saved (backup) or default configuration file. 68

config save Store the current configuration in a backup file. 69

E-DOC-CTC-20050531-0061 v1.0

63

Config Commands

config delete

Delete a user configuration file.

SYNTAX:

config delete [filename = <string>]

where:

filename Name of the user configuration file to be deleted.

Note If not specified, all the user configuration files that were saved in the

SpeedTouch™ permanent storage will be deleted.

RELATED COMMANDS:

config dump Show the saved configuration file.

OPTIONAL

64

E-DOC-CTC-20050531-0061 v1.0

config dump

Show the saved configuration file.

SYNTAX:

config dump

RELATED COMMANDS:

config delete Delete a user configuration file.

Config Commands

E-DOC-CTC-20050531-0061 v1.0

65

Config Commands

config flush

Flush the loaded configuration.

1. This flush command combines all the possible flush commands.

2. This command does not affect saved configurations.

SYNTAX:

config flush [flush_ip = <{disabled | enabled}>]

where:

flush_ip Flush IP settings (enabled) or not (disabled).

The default is disabled.

Note Not keeping the IP settings could cause lost IP connectivity in the LAN.

OPTIONAL

66

E-DOC-CTC-20050531-0061 v1.0

config list

Show the current configuration set.

SYNTAX:

config list [templates = <{disabled | enabled}>]

where:

Config Commands

templates List the template files (disabled) or not (enabled).

The default is disabled.

RELATED COMMANDS:

config load Load complete saved (backup) or default configuration file.

config save Store the current configuration in a backup file.

OPTIONAL

E-DOC-CTC-20050531-0061 v1.0

67

Config Commands

config load

Load complete saved (backup) or default configuration file.

Use the command :config flush before loading a configuration file.

SYNTAX:

config load [load_ip = <{disabled | enabled}>]

where:

[defaults = <{enabled | disabled}>]
[flush = <{enabled | disabled}>]
[echo = <{disabled | enabled}>]
[filename = <string>]

load_ip Load IP settings (enabled) or not (disabled).

OPTIONAL

Note Not keeping the IP settings could cause lost IP connectivity in the LAN.

defaults Load default configuration (enabled) or saved configuration (disabled).

OPTIONAL

Note If not specified, the saved configuration will be loaded.

flush Flush the current configuration before loading a new configuration (enabled) or not

(disabled).

echo Echo each command string when loaded (enabled) or not (disabled). OPTIONAL

filename Name of the configuration file to be loaded. OPTIONAL

OPTIONAL

EXAMPLE:

=>ip rtlist

Destination Source Gateway Intf Mtrc

10.0.0.0/24 10.0.0.0/24 10.0.0.140 eth0 0

172.16.0.5/32 0.0.0.0/0 172.16.0.5 cip1 0

10.0.0.140/32 0.0.0.0/0 10.0.0.140 eth0 0

127.0.0.1/32 0.0.0.0/0 127.0.0.1 loop 0

172.16.0.0/24 0.0.0.0/0 172.16.0.5 cip1 1
=>config load flush_ip=no
=>ip rtlist

Destination Source Gateway Intf Mtrc

10.0.0.0/24 10.0.0.0/24 10.0.0.140 eth0 0

10.0.0.140/32 0.0.0.0/0 10.0.0.140 eth0 0

127.0.0.1/32 0.0.0.0/0 127.0.0.1 loop 0
=>config load flush=yes
=>ip rtlist

Destination Source Gateway Intf Mtrc

10.0.0.0/24 10.0.0.0/24 10.0.0.140 eth0 0

10.0.0.140/32 0.0.0.0/0 10.0.0.140 eth0 0

172.16.0.5/32 0.0.0.0/0 172.16.0.5 cip1 0

127.0.0.1/32 0.0.0.0/0 127.0.0.1 loop 0

172.16.0.0/24 0.0.0.0/0 172.16.0.5 cip1 1
=>

RELATED COMMANDS:

config list Show the current configuration set.

config save Store the current configuration in a backup file.

68

E-DOC-CTC-20050531-0061 v1.0

Config Commands

config save

Store the current configuration in a backup file.

All the existing configurations and modifications entered by the user are saved.

The backup file is saved in the SpeedTouch™ permanent storage. This file can be downloaded via the
SpeedTouch™ web pages or via an FTP session.

SYNTAX:

config save filename = <string>

where:

filename The filename for the backup file of the current configuration. REQUIRED

RELATED COMMANDS:

config list Show the current configuration set.

config load Load complete saved (backup) or default configuration file.

E-DOC-CTC-20050531-0061 v1.0

69

Config Commands

70

E-DOC-CTC-20050531-0061 v1.0

Connection Commands

Connection Commands

Introduction

This chapter describes the commands of the connection command group.

Contents

This chapter covers the following commands:

connection appconfig Configure the available CONN/NAT application helpers. 72

connection appinfo Display CONN/NAT application specific info. 74

connection applist List the available CONN/NAT application helpers. 75

connection bind Create a new CONN/NAT application helper/port binding. 76

connection bindlist List the current CONN/NAT application helper/port bindings. 77

connection clean Clean the connection database by forcing timeouts. 78

connection clear Kill all the connections. 79

connection config Configure the connection handling. 80

connection debug The connection debug commands 81

connection describe Describe the streams of a connection. 82

connection flush Flush the current connection configuration. 83

connection info Show all the registered modules with some info. 84

connection list Display the currently known connections. 85

connection refresh Invalidate all the cached decisions. 86

connection stats Display the connection and stream statistics. 87

connection timerclear Clear the connection timeout to default. 88

connection timerconfig Configure the connection timeout handling. 89

connection unbind Delete an existing CONN/NAT application helper/port binding. 90

E-DOC-CTC-20050531-0061 v1.0

71

Connection Commands

connection appconfig

Configure the available CONN/NAT application helpers.

SYNTAX:

connection appconfig application = <string>

where:

[trace = <{disabled | enabled}>]
[timeout = <number{0-32000}>]
[floating = <{disabled | enabled}>]
[tracelevel = <number{1-4}>]

application The name of a CONN/NAT application helper.

REQUIRED

Tip Use the command :connection applist to obtain a list of CONN/NAT

application helpers.

trace Enable or disable CONN/NAT application helper traces.

The default is enabled.

timeout A number between 0 and 32000 (seconds).

Represents the maximum timeout to keep predicted child connections around.

floating Enable / disabled floating port for IKE helper. OPTIONAL

tracelevel A number between 1 and 4.

Represents the SIP trace level.
Choose between:

OPTIONAL

OPTIONAL

OPTIONAL

 1: feature errors

 2: feature traces

 3: all errors

 4: all traces.

The default is 1.

EXAMPLE:

=>connection applist
Application Proto DefaultPort Traces Timeout
IP6TO4 6to4 0 enabled unavailable
PPTP tcp 1723 enabled unavailable
ESP esp 0 unavailable 15' 0"
IKE udp 500 disabled 15' 0" FLOATING
SIP udp 5060 disabled 6 0" trace level 1
...
LOOSE(UDP) udp 0 enabled 5' 0"
FTP tcp 21 enabled unavailable
=>connection appconfig application=SIP trace=enabled
=>connection applist
Application Proto DefaultPort Traces Timeout
IP6TO4 6to4 0 enabled unavailable
PPTP tcp 1723 enabled unavailable
ESP esp 0 unavailable 15' 0"
IKE udp 500 disabled 15' 0" FLOAATING
SIP udp 5060 enabled 6 0" trace level 1
...
LOOSE(UDP) udp 0 enabled 5' 0"
FTP tcp 21 enabled unavailable
=>

72

E-DOC-CTC-20050531-0061 v1.0

RELATED COMMANDS:

connection appinfo Display CONN/NAT application specific info.

connection applist List the available CONN/NAT application helpers.

Connection Commands

E-DOC-CTC-20050531-0061 v1.0

73

Connection Commands

connection appinfo

Display CONN/NAT application specific info.

SYNTAX:

connection appinfo application = <{string}>

where:

application The name of a CONN/NAT application helper.

Tip Use the command :connection applist to obtain a list of CONN/NAT

application helpers.

EXAMPLE:

=>connection appinfo application=SIP
SIP ALG session SIPALG: pool=138, in use=0, bottom=138

=>

RELATED COMMANDS:

connection appconfig Configure the available CONN/NAT application helpers.

connection applist List the available CONN/NAT application helpers.

REQUIRED

74

E-DOC-CTC-20050531-0061 v1.0

connection applist

List the available CONN/NAT application helpers.

SYNTAX:

connection applist

EXAMPLE:

=>connection applist
Application Proto DefaultPort Traces Timeout
IP6TO4 6to4 0 enabled unavailable
PPTP tcp 1723 enabled unavailable
ESP esp 0 unavailable 15' 0"
IKE udp 500 disabled 15' 0" FLOATING
SIP udp 5060 disabled 6 0" trace level 1
JABBER tcp 5222 disabled 2' 0"
CU/SeeMe udp 7648 enabled unavailable
RAUDIO(PNA) tcp 7070 enabled unavailable
RTSP tcp 554 enabled unavailable
ILS tcp 389 unavailable 5' 0"
H245 tcp 0 unavailable 5' 0"
H323 tcp 1720 enabled unavailable
IRC tcp 6667 enabled 5' 0"
LOOSE(UDP) udp 0 enabled 5' 0"
FTP tcp 21 enabled unavailable
=>

Connection Commands

For some CONN/NAT application helpers, either traces or timeout are unavailable.

RELATED COMMANDS:

connection appconfig Configure the available CONN/NAT application helpers.

connection appinfo Display CONN/NAT application specific info.

E-DOC-CTC-20050531-0061 v1.0

75

Connection Commands

connection bind

Create a new CONN/NAT application helper/port binding.

SYNTAX:

connection bind application = <string>

where:

port = <port-range>

application The name of a CONN/NAT application helper.

REQUIRED

Tip Use the command :connection applist to obtain a list of CONN/NAT

application helpers.

port The port number or port range this application handler should work on. REQUIRED

EXAMPLE:

=>connection bindlist
Application Proto Portrange Flags
JABBER tcp 15222
JABBER tcp 5222
FTP tcp 21
IRC tcp 6660
...
IP6TO4 6to4 0
=>connection bind application = IRC port = 6750
=>connection bindlist
Application Proto Portrange
IRC tcp 6750
JABBER tcp 15222
JABBER tcp 5222
FTP tcp 21
IRC tcp 6660
...
IP6TO4 6to4 0
=>

RELATED COMMANDS:

connection bindlist List the current CONN/NAT application helper/port bindings.

connection unbind Delete an existing CONN/NAT application helper/port binding.

76

E-DOC-CTC-20050531-0061 v1.0