Page 1
Set Up
Simple
may be required for installation
Phillips head screwdriver or drill
Tools
Quick
Model: AHS613
ALC CONTROL APP
Download the ALC Connect App
as follows:
APPLE IOS DEVICE:
From your iPhone or iPad, go to the
App Store and search for ALC Connect.
ANDROID DEVICE:
From your Android smartphone or tablet
device, go to Google Play and search for
ALC Connect.
Wireless
STATUS SCREEN
Add Device
Return
Device Icon
Status
Display
Arm/Disarm
Edit
Device
Name
Device
Location
Status
Indicator
Door/Window Closed
Door/Window Open
Sensor On
ON
Sensor Off
OFF
Sensor Triggered
Battery Low
Made Simple.
ALCWireless.com
pairing mode.
the unit ON activates the manual
device as you pair them. Turning
recommended to turn ON each
For first time use, it is
120V/60Hz AC outlet.
*Insert the Power Switch into a
Place unit back on bracket.
outlet.
the other end into a 120V/60Hz AC
Connect AC Adapter to DC IN Jack and
Quick Start Guide
Remote Control x1
Status
Scenario
System
Setting
Event List
Edit Icon
(Appears in
Edit Mode)
Tamper Alert
Delete
Edit Mode
IMPORTANT: All accessories are paired with the Control Hub at the factory. See below to pair again or to add devices.
door/window frame.
120V/60Hz AC outlet.
DC IN Jack and the other end into a
the Siren or connect the AC Adapter to
batteries (not included) into the back of
minimum obstacles. Insert four AA
install in a highly visible location with
screws as shown. It is recommended to
Remove back cover and insert the three
Siren
smaller piece to the movable part of the
window. Make sure to attach the
Select a location on either a door or a
sections of the Door/Window sensor.
double-sided tape to the rear of both
Sensor for first time use. Apply the
pre-installed in the Door/Window
A CR2032 battery has been
Door/Window Sensor
the Control Hub.
from the router to the Ethernet jack on
Connect the supplied Ethernet cable
Control Hub
Installation
and Screw Set x1
Siren With AC Cord, Bracket
Battery and Sticky Pad Set x1
Door/Window Sensor with
Ethernet Cable x 1
Control Hub with AC Cord and
IN THE BOX
FO LD
PAIRING THE CONTROL HUB
Launch the previously installed ALC
1
Connect App. At the next screen, tap Next,
then tap Next again; The app will search for
the Control Hub and retrieve the Control
Hub DID automatically.
CHANGING THE PASSWORD
After pairing the hub, it is very important to
1
2
3
change the password. To change, tap the
Setting icon.
Enter 123456, then tap Confirm.
Tap Security Setup. At this screen
you can change the Security Code
and Admin Password. You can also
enable/disable and set up a PIN Lock
for the app once enabled; you will
need to enter the PIN Lock code to
enter the app. Tap Save when done.
PAIRING REMAINING DEVICES
The remaining devices are paired similar
1
2
3
ways. The siren and power switch will be
ready to pair upon plugging in. For the
other devices, remove the Plastic Tab to
enable the pairing.
At the Status screen, tap +.
Tap the desired device then tap Pair;
the App will then search for and pair
the selected device.
TROUBLE PAIRING?
If the devices do not pair properly, then
utilize the manual Pairing as follows:
Door/Window Sensor: If it did not detect
the sensor, pair manually by removing the
battery for 5-10 seconds and then reinstall
it (this will activate the manual pairing).
Motion Detector: If it did not detect the
sensor, pair manually by removing the
battery cover and then press the Pair
button.
Remote Control: If it did not detect the
Remote Control, press and hold the Armed
Stay button on the Remote Control until
the blue LED blinks.
Siren: If it did not detect the Siren and
press the Pair button located inside the
battery compartment.
FO LD
INSTALLATION OVERVIEW
Control Hub
Secure wireless central home
control/management center.
Adapter DC 12V/1A
Remote Control
Wireless multi-functional panic
remote controller.
Battery CR2032
Indoor Siren
Wireless portable/wall-mount
alert siren.
Adapter DC
5V/1A
or
Batteries AA 1.5V x 4
(not included)
Door/Window Sensor
Wireless door/window access
alert sensor.
Battery CR2032
Wireless Made Simple.
The following screen will appear, enter the
2
ACCESSORY
Compatible with ALC AHS613, AHS616, and
AHS629 Security Systems
desired System Name and the security
code. The default security code is
123456.
If not on the Control Hub screen already,
3
tap the Control Hub or System Name you
gave on step 2 to enter the main Status
screen.
Enter the device’s name and Location
4
and then tap Save.
Wireless Security
BASIC OPERATION
System
Home Security Anytime from Anywhere
Model: AHS613
QUICK START GUIDE
Please read these instructions completely
before operating this product.
When first turning on
1
2
NOTE: Do not place any device near water. STRANGULATION HAZARD: Infants have STRANGLED in power cords.
Keep power cords more than 3 feet away from cribs. When using your equipment, always follow basic safety precautions to reduce
the risk of fire, electric shock and injury to persons. Illustrations are for reference only. Actual product specifications may vary.
For additional precautions and product information, please see owner’s manual at www.ALCWireless.com/support
the app you will enter
the Control Hub (or
System Name you
gave) Selection
window. Simply tap
your Control Hub to
enter.
The Status screen
will then appear.
Click a device
(except
Door/Window
Sensor) to set as
follows:
Siren: Tap the Siren
icon, then turn the
Siren On or Off.
Remote Control: Tap
the Remote Control
icon and then an
icon below to
activate the
respective function
corresponding to
the buttons on the
remote control.
Note that the button
operation can be
changed, see the
owner’s manual.
Power Switch (Available Separately): Tap the
3
4
Power Switch icon, then turn the Power Switch
On or Off.
Camera (Available Separately): Tap the Camera.
At this screen you can view the camera. Also tap
the icons under the image to perform the
following:
Snapshot: Tap to capture screen images.
The snapshots will be saved into the
camera roll of your mobile device.
Mute/Un-mute: Press to hear the
sound of the camera’s microphone
through the App. Tap again to mute
the sound.
Record: Tap to record. Video records
for about 1 minute.
Note: A Micro SD Card (not included)
is required to use the recording
function on the camera. Insert to
the side of the camera.
For detailed installation and setup and to view the ALC 1 Year
Limited Warranty, please refer to the complete User’s Guide
available on our website: www.ALCWireless.com/support
STAY/AWAY ARMING THE SYSTEM
When on the Status page, tap to Arm/Partially disarm the system.
Select one of the following options:
Stay: Only arms the Door/Window sensors so you can stay at home.
Away: Arms all devices, including motion sensors if installed.
EMAIL/PUSH NOTIFICATIONS
Tap the Setting icon on the bottom
1
of the App to enter the Setting
screen. Enter the Admin Password
(default is 123456).
Tap Notification Setup. At this
2
screen you can disable/enable
Email Notifications and/or Push
Notifications. Also set an email
address to send alerts to. Tap Save
when done.
SCAN
TO VIEW
COMPLETE
USER’S GUIDE
BACK cover
FO LD
Front cover
Loading...