Do not expose the camera battery pack or other
accessories to rain or humidity to prevent fire
hazard or electric shock.
For customers in the U.S.A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
FCC Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
For customers in Europe
"CE" mark indicates that this product
complies with the European requirements
for safety, health, environment and customer
protection. "CE" marked cameras are intended for
sales in Europe.
This symbol [crossed-out wheeled bin WEEE
Annex IV] indicates separate collection of
electrical and electronic waste in the European
countries. Please do not throw the equipment into
the waste. Please recycle and dispose of properly.
Declaration of Conformity
Model Name: OPTIMA 3
Trade Name: AgfaPhoto
Responsible Party:
plawa-feinwerktechnik GmbH & Co. KG
Address: Bleichereistrasse 18, 73066 Uhingen, Germany
Customer Care Hotline:
Conforms to the following Standards:
EMC: EN 55022:1998/A1:2000/A2:2003 Class B
EN 55024:1998/A1:2001/A2:2003
EN 61000-3-2:2000/A1:2001
EN 61000-3-3:1995/A1:2001
following the provision of the EMC Directive (89/336/
EEC, 2004/108/EEC)
Germany: 0900 1000 042; 1,49€/ Min.
Europe: 00800 7529 2100
UK: +44 1908 488676,
Hong Kong: 852 3586 9168
i
Page 3
SAFETY PRECAUTIONS
Camera notes:
Do not store or use the camera in the following
environments:
• In the rain, and in humid or dusty environments.
• In a place where the camera can be exposed
directly to the sunlight or subject to high
temperature, e.g. Inside a closed car in summer.
• In a place where the camera is subject to a high
magnetic field, e.g. near motors, transformers or
magnets.
Do not place the camera on a wet surface or places
where dripping water or sand may come in contact
with the camera.
If the camera will not be used for a long period of
time, remove the battery and the memory card from
the camera and store them in dry environment.
If you carry the camera suddenly from a cold location to a warm place, moisture may condense inside
the camera. It is suggested that you wait for a while
before turning on the camera.
The warranty does not cover any type of data loss
or corruption.
• Do not expose the batteries to water, and take
particular care to keep the terminals dry.
• Do not heat the batteries or throw them into a fire.
• Do not attempt to deform, disassemble or modify
the batteries.
Keep the batteries out of reach of babies and small
children.
In cold locations, battery performance deteriorates
and battery life is significantly shortened.
Memory card notes:
When using a new memory card, be sure to format
the card with your digital camera before using it.
Do not change or delete the folder names or file
names in the memory card from your PC, the camera
will not be able to display those edited files on the
its LCD screen. To edit image data, copy the image
data to the PC’s hard disk first.
The photos taken by this camera are stored in the
auto-generated folder in SD card. Please do not
store photos that are not taken by this model of
camera, as this may make it impossible to recognize
the picture when the camera is in playback mode.
Battery notes:
Incorrect use of the batteries may cause them to
leak, become hot, ignite or burst. Always observe the
following precautions.
iiii1
Page 4
BEFORE YOU START
Preface
Thank you for purchasing this AgfaPhoto digital
camera. Please read this manual carefully and keep
it in a safe place for future reference.
No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form, by any means, without the
prior written permission of plawa-feinwerktechnik
GmbH & Co. KG.
Trademarks
All trademarks mentioned in this manual are used
for identification purposes only and are properties
of their respective owners.
Safety Information
Please read the following important information
carefully before using the product.
• Do not take apart or attempt to service the
camera yourself.
• Do not drop or knock the camera. Improper han
dling may damage the product.
• Turn off the camera before inserting or removing
the battery and memory card.
• Use only the type of battery that comes with the
camera. Using other types of batteries may damage the camera and void the warranty.
• Do not touch the camera lens.
•
Please not expose the camera to harsh
environments such as moisture, or extreme
temperatures, which may shorten the life of your
camera or damage the batteries.
• Do not operate or store the camera in dusty,
dirty, or sandy environments.
-
Page 5
AgfaPhoto OPTIMA 3
• Do not expose the lens to direct sunlight for
extended periods.
• Download all pictures and remove the batteries
from the camera if you are going to store the
camera for long periods of time.
• Do not use abrasive cleansers, alcohol-based, or
solvent-based cleaners to clean the camera. To
clean, wipe the camera with a slightly damp soft
cloth.
About This Manual
This manual provides you with instructions on how
to use your AgfaPhoto digital camera. Every effort
has been made to ensure that the contents of this
manual are accurate, however plawa-feinwerktechnik GmbH & Co. KG reserves the right to make
changes without notice.
Symbols used in this manual
Throughout this manual, the following symbols are
used to help you locate information quickly and
easily:
Indicates the useful information to know.
Indicates precautions to be taken while
operating the camera.
Video System ................................................................... 66
Connecting to a PC .......................................................67
Setting the USB Mode ........................................67
Transferring Files to your PC .......................... 67
6
67
Page 10
GETTING READY
Unpacking
Your package should contain the camera model you purchased along with the following items. If anything is
missing or appears to be damaged, please contact plawa-feinwerktechnik GmbH & Co. KG.
USB Cable
CD-ROMWarranty Card
Wrist Strap
Battery chargerRechargeable Lithium-ion battery
Page 11
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
13
2
5
4
6
7
8
9
10
11
Camera Views
Front ViewBack View
Right View
89
Page 12
AgfaPhoto OPTIMA 3
16
17
15
14
1918
20
13
12
Top View
Left View
Bottom View
1Flash11Function/OK Button
2Lens12USB/AV Port
3AF assist beam/Timer indicator 13Wrist Strap Mount
4LCD Screen14Power Button
5Mode Selection Button15Playback Button
6Menu Button16Shutter Button
7Disp/Up Button17Zoom Wheel
8Flash Mode/Right Button18Tripod Mount Point
9Delete Button/Down Button19Speaker
10Face Detection/Left button20
Memory Card/Battery
Compartment
9
Page 13
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
1
2
Charging the Battery
1. Place the battery into the charger as shown.
2. Plug the one end of the connecting cable (plug
adapter) into the charger base.
3. Plug the other end of the connecting cable into a
wall outlet.
Leave the battery to charge until the charger
light turns green. (To maximize battery life, the
first charge should be at least 4 hours)
The charger is for indoor use only.
1011
Page 14
Insert the Battery and SD/SDHC Card (Not included)
1. Open the battery compartment.
2.Insert the battery while observing the correct
polarity. Use the side of battery to press down
the stopper as shown, allowing the battery to
lock into place properly.
Page 15
AgfaPhoto OPTIMA 3
memory card slot as shown.
12
1213
4. Close the battery compartment.3. Insert an SD/SDHC card (not included) into the
Page 16
AgfaPhoto OPTIMA 3
Optional SD/SDHC cards are not included. The
use of 64 MB to 16 GB memory cards from
recognized manufacturers such as SanDisk,
Panasonic and Toshiba is recommended for
reliable data storage.
To remove the SD/SDHC card, open the
battery compartment and gently push the card
to release it. Pull the card out carefully.
Turning On and Off
Press the Power button to turn the camera on. To
turn off the camera, press the Power button again.
Power Button
When the camera is turned on, it will be at the
same shooting mode based on the last use. You
can use the Mode button on the back to change
modes. When using the camera for the first-time,
the language setup page will appear. Please see
page 15 or the Quick Start Guide in the package for
details.
Page 17
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
M
Using the Mode Button
The AgfaPhoto camera provides a convenient mode Button that allows you to switch between different modes
easily. After pressing the mode button to enter mode selection menu, press Left/Right button to choose the
mode, press to select. All the available modes are listed as follows:
Mode NameIconDescription
Auto mode
Manual mode
Panorama mode
Scene mode
Movie mode
ASCN mode
Portrait
The camera sets all the settings automatically.
Switch to take still pictures in manual mode, where many camera settings can be
configured. (Recommended for advanced users only)
Switch to capture 4 shots and stitch them together into a panoramic photo.
Switch to take still pictures in 12 different scene types by your choice.
Switch to record videos.
Switch to have the camera automatically select the best scene type for still
pictures.
Switch to take portrait pictures.
1415
Page 18
Setting Date/Time and Language
Setting the Date and Time
1. Press the menu button. Scroll over to the
General Setup menu indicated by a wrench icon.
Use the
Then press the
2. Press the
use the
3. Press the
Up/Down
Up/Down
button to select
Right button
Left/Right
to adjust the value.
button to confirm the setting.
to enter the setting.
to highlight each field and
Date/Time
.
Page 19
AgfaPhoto OPTIMA 3
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Setting the Language
1. Press the menu button. Scroll over to the
General Setup menu indicated by a wrench icon.
Use the
Then press the
2. Use the Left/Right buttons to select the desired
language.
3. Press the button to confirm the setting.
16
1617
Up/Down button
Right button
to go to the
to enter the setting.
Language
.
The Date/Time and Language setup will
automatically appear when the camera is
turned on the first time.
Page 20
About the LCD Screen
When you turn the camera on, various icons are
shown on the LCD screen to indicate the current
camera settings and status. To learn more about
the displayed icons, see “LCD Screen display” on
page 25.
LCD Screen notes:
Extremely high-precision technology has been used
to manufacture the LCD screen so that most of the
pixels are operational for use. However, there may
be some minute points (black, white, red, blue or
green) that constantly appear on the LCD screen.
These points are normal in the manufacturing
process and the recording is not affected in any
way.
Avoid exposing the LCD screen to water;
please remove any moisture on the LCD
screen with a soft dry cleaning cloth.
If the LCD monitor is damaged, take particular
care with the liquid crystal in the monitor. If
any of the following situations arise, take the
recommended immediate action indicated
below:
• If liquid crystal comes in contact with your
skin, wipe the area with a cloth and then wash
thoroughly with soap and running water.
• If liquid crystal gets into your eye, flush the
affected eye with clean water for at least 15
minutes and then seek medical assistance.
• If liquid crystal is swallowed, flush your mouth
thoroughly with water. Drink large quantities of
water and induce vomiting. Then seek medical
assistance immediately.
Page 21
W
T
BASIC OPERATION
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Shooting in Auto Mode
Auto mode is the easiest mode to take photos.
While operating in this mode, the camera
automatically optimizes your photos for best
results.
To start shooting, do the following:
1. Press
2. In the Mode menu, select the Auto mode ( ).
3. Compose your picture on the LCD screen and
4. The focus frame in the middle of the LCD will
5. Press Shutter fully to capture the image.
Power to turn the camera on.
press the Shutter button halfway to focus on
the subject.
turn to green when the subject is properly in
focus.
18191819
Using the Zoom Function
Your camera is equipped with two types of zoom:
optical zoom and digital zoom. Use zoom control
at the top of the camera to zoom in or out on your
subject while taking pictures.
Zoom indicator
(See “Digital
Zoom“ on page
47)
When the optical factor reaches its maximum value,
it stops momentarily. Release and push the zoom
wheel again, and the optical zoom will switch over
to digital zoom automatically. After the adjustment,
the zoom indication scale hides immediately,
and the current zoom status is indicated by the
following symbol .
Page 22
Basic Functions Menu
The Basic Function Menus of the camera include
Flash, Self-timer, Macro Capture, and Exposure
Compensation.
Set the basic functions as per the following steps:
1. Pull up the Basic Function Menus by pressing
Right/Flash button.
2. Press Left/Right button to select the settings of
the required function.
3. Press
button to confirm the settings and exit
the menu, or press Down button to enter the
selection screen of Basic Function.
4. Press Left/Right button to select the basic
functions required to set, press Up button to
enter the setting screen for selecting basic
functions, or press button to confirm the
settings and exit the screen.
Flash
•
•
Flash: Auto
Camera flash fires if camera determines it
is needed.
Flash: Red-eye reduction
Red eye is caused by the subject looking
directly at the flash and the resulting light
reflecting off of the retina of the eye. Red
eye is eliminated by firing a smaller initial
flash prior to the main flash to cause the
subject not to look directly at the flash.
Page 23
AgfaPhoto OPTIMA 3
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
•
• Flash: Forced off
• Flash: Slow Synchro
• Flash: Red-Eye+Slow Synchro
Flash: Forced flash
Flash always fires.
Flash is turned off.
This allows you to take pictures of people
at night that clearly show the subject. The
shutter is held open longer to allow more
light to the image sensor.
Using this mode for slow synchro shots
with red-eye reduction.
Self-timer/Continuous Capture
•
•
•
20
2021
Self-timer: 2 sec
A single picture is shot 2 seconds after the
Shutter button is pressed.
Self-timer: 10 sec
A single picture is shot 10 seconds after
the Shutter button is pressed.
Self-timer: Unlimited
Pictures are shot continuously when the
Shutter button is pressed down based on
the Continuous Shot settings in the menu.
(See “Continuous Shot” on page 45).
•
Self-timer: Off
Disables the self-timer.
Macro Mode
•
•
Macro: On
Select this to focus on subjects 5cm from
the lens.
Macro: Off
Select this option to disable Macro.
Exposure Compensation
The exposure compensation allows you to adjust
the light exposure value and shoot the best photo.
The adjustable range of exposure value is from EV
-2.0 to EV+2.0.
Page 24
Advanced Functions Menu
The Advanced Functions Menu of the camera
include Image Size, Image Quality, White Balance,
Image Color and ISO.
Set the advanced functions as follows.
1. Pull up the Advanced Function Menu by pressing
button.
2. Press Left/Right button to select the settings of
the required function.
3. Press
button to confirm the settings and exit
the menu, or press Down button to enter the
selection screen of Advanced Functions.
4. Press Left/Right button to select the advanced
functions required to set, press Up button to
enter the setting screen for selecting advanced
functions, or press button to confirm the
settings and exit the screen
Page 25
AgfaPhoto OPTIMA 3
M
WB (White Balance)
The White Balance allows you to adjust the color
temperature under different lighting conditions.
(The WB setting is only available when the camera
is in the M Manual mode).
The options of White Balance include:
•
•
•
•
•
•
•
22
WB: Auto
WB: Daylight
WB: Cloudy
WB: Fluorescent
WB: Fluorescent CWF
WB: Incandescent
WB: Manual (Press the shutter button to
set WB.)
ISO
The ISO function allows you to set the sensitivity
of the camera sensor to light. To improve the
performance in darker environments, a higher ISO
value is required. On the other hand, a lower ISO
value is needed when in bright conditions. (The ISO
setting is only available when the camera is in the
Manual mode).
Pictures at higher ISO will naturally have more noise
than those at lower ISO.
The options of ISO include automatic, 80, 100, 200,
400, 800, 1600 and 3200.
The available ISO values vary on different
camera models.
Page 26
AgfaPhoto OPTIMA 3
Quality
The quality setting determines how much the
camera compresses the photo files. The higher
the compression, the smaller the file size will
be, but the quality will decrease. The lower the
compression, the larger the file size, but the better
the quality.
The three levels of compression are:
• :
• :
•:
Quality: Best
Quality: Fine
Quality: Normal
Size
The size setting refers to the image resolution in
pixels. A higher image resolution allows you to print
that image in larger sizes without degrading the
image quality.
The larger the pictures are, the bigger the file
sizes are and the less pictures you can store
on a memory card.
23
Page 27
AgfaPhoto OPTIMA 3
Color
The color setting allows you to add artistic effects
directly when taking pictures. You can try different
color tones to alter the mood of your pictures. (The
Color setting is only available when the camera is in
the M Manual mode).
The color options include:
•
Color: Auto
•
•
•
24
2425
Color: Vivid
Color: Black & White
Color: Sepia
Page 28
USING THE MODES
12345678
9
10
11
1213
14
15
16
17
19 20 21 22 23
18
LCD Screen Display
Still Picture Mode Display
Mode: M
1 Shooting Mode Icons
Manual mode
Scene mode
Portrait
AF Mode
2
Auto mode
ASCN mode
Panorama mode
Single-AF
Multi-AF
3
Expo Metering
Spot
Center
AiAE
Image Size
4
Image Quality
5
Page 29
AgfaPhoto OPTIMA 3
6 Remaining number of pictures
7
Memory card/built-in memory
8
Battery Status
9
WT Ratio (Displayed only when zoom is
activated)
10
Zoom
11
Exposure
12
ISO Value (Adjustable only in M Manual Mode)
13
Histogram
14
Focus Frame
15
Slow Shutter Warning
16
Continuous Shot
17
Face Detection
18 OIS
Continuous ON
In shooting
19
Picture Color (Adjustable only in M Manual
Mode)
20
White Balance (Adjustable only in M Manual
Mode)
21
Macro Mode
26
22 Self-timer
Self-timer: 2 sec
Self-timer: 10 sec
23 Flash Mode
Flash: Auto
Flash: Red-eye reduction
Flash: Forced flash
Flash: Forced off
Flash: Slow Synchro
Flash:Red-Eye+Slow Synchro
Page 30
AgfaPhoto OPTIMA 3
10
11
12
14
13
123478956
Video Shooting Mode Display
Mode :
1 Video Mode icon
2 Continuous AF
3 Metering
4
Image Size
5
Macro mode
Spot
Center
AiAE
6 Self-timer
Self-timer: 2 sec
Self-timer: 10 sec
7
Remaining Time for Video Recording
8 Memory Card/Built-in Memory
9 Battery Status
10 WT Ratio (Displayed only when zoom is
activated)
11 Zoom
12
Exposure
13 OIS
Continuous ON
In shooting
14
Recording Status Icon
Recording standby
Recording
In order to shoot video, it is recommended
that an SD card be used.
When shooting video, the optical zoom is
disabled.
27
Page 31
AgfaPhoto OPTIMA 3
123456
7
8
9
1011
13
OK:PLAY
12
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Playback Mode Display
Mode:
1. Play Mode icon
2.
Picture File
3.
File protection
4.
Picture Number
5.
Memory Card/Built-in Memory
6.
Battery Status
7. Image Zoom
8.
The current display area
9. Zoom area shown
10.
Memory Space (this picture/Total number of
pictures)
11.
Recording Date and Time
12. OK:PLAY
13.
28
2829
DPOF file
Page 32
Auto Scene Mode (ASCN)
In the "ASCN" mode, different conditions are
detected intelligently and the most suitable settings
will be automatically selected.
To use "ASCN":
1.
Press Mode Selection button to select ASCN
mode, LCD screen will be shown as follows.
2. Hold the camera steadily and aim at the subject.
The optimum scene mode will be identified
automatically.
3. Press the Shutter button halfway down to focus.
4. Press the Shutter button all the way down to
take the picture.
Icon Mode nameIcon Mode name
Landscape
Mode
Portrait ModeMacro Mode
Night PortraitAuto Mode
Backlit
Portrait
Night Landscape
Mode
Landscape Mode
For landscapes, ASCN will automatically adjust the
exposure to match the background.
Portrait Mode
For portraits, ASCN will automatically adjust the
exposure and skin tones to give clear pictures.
Page 33
AgfaPhoto OPTIMA 3
Night Portrait
When you shoot portraits at night, or in low light
conditions, ASCN will automatically adjust the
exposure for people and night scenes.
Backlit Portrait
When the sun or any other light source is behind
you, ASCN will automatically adjust the foreground
exposure to produce good pictures.
Night Landscape Mode
For night scenes, ASCN will automatically increase
the ISO value to compensate for low light.
Macro Mode
To capture object detail for close-ups, ASCN will
automatically adjust the focus.
Auto Mode
The camera automatically adjusts the exposure and
focus to ensure good pictures.
Panorama
Panorama Mode allows you to create a panoramic
picture by stitching together several pictures.
Follow these steps to create a panoramic picture:
1.
Press Mode Selection button to select Panorama
Synthesis mode
2. Use the
direction of picture taking, if no choice is made
in 2 seconds the panoramic sequence will
commence automatically.
3. Compose the first view of the panoramic picture
on the LCD screen and press the Shutter button
to capture.
4.
After the first shot is taken, two target icons
will appear on the left and right side of the
LCD screen. Pan the camera in the specified
direction and the circle will move towards the
square frame icon. When the circle icon and
square frame overlap they will become green
and the camera will capture the next picture
automatically.
Left/Right buttons to specify the
3031
Page 34
5. The camera will then stitch the pictures
automatically.
6. Press the playback button to enter Playback
mode and review the result.
Pictures cannot be deleted, nor the zoom
adjusted until the series is finalized.
2~4 images can be stitch together.
AgfaPhoto OPTIMA 3
Page 35
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Manual Scene Mode (SCN)
In Manual Scene mode, you can select from a total
of 12 scene types to match your needs. You just
need to select the right scene for the occasion and
the camera will automatically adjust to the optimal
settings for you.
Press the button, select "SCN" with the
Left/Right button, and the LCD screen will show the
figures as below.
Select a scene using the Left/Right button and
press the button.
IconMode NameIconMode Name
SportIndoor
SnowFireworks
Museum
ChildrenLeaf
SunsetGlass
LandscapeNight Portrait
Night
Landscape
Sport
For fast-moving subjects. Capture sharp action
shots without blur.
Indoor
For indoors. Reduce blur and improve color ac-
3233
curacy.
Page 36
AgfaPhoto OPTIMA 3
Snow
For snow scenes. Reproduce natural and clear
white scenes.
Fireworks
For fireworks at night. Slow shutter speed adjusted
for brilliant images.
Museum
For museum or flash-free area. Retain color and
reduce blur.
Night Landscape
For night scenes. Use of tripod is recommended.
Children
For kids and pets. Flash is disabled for eye
protection.
Leaf
For plants. Capture brilliant shots of greenery and
blossoms.
Sunset
For sunsets. Capture subjects in strong sunlight.
Glass
For objects behind transparent glass.
Landscape
For landscapes. Vivid reproduction of green and
blue.
Night Portrait
For portraits against night time scenery.
33
Page 37
AgfaPhoto OPTIMA 3
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
1. After selecting the scene type, press the
button to select.
2. To select a different scene type, press the
button to enter the main function menu. Then
press it again to return to the to Scene selection
menu.
The main function menu also allows you to adjust
the image quality and image size. Please refer to
the "Advanced Functions Menu" section on page
21 for detailed instructions.
34
3435
Page 38
Face Detection
The Face Detection mode will detect and enhance
facial features.
1. In Shooting mode, press the Left/Face Detection
button to turn on the Face Detection and an icon
( ) appears on the LCD.
2. Hold the camera securely, and point the camera
towards the subject to start the face detection
process. When the camera detects a face, a
white rectangular frame will be drawn around
the face. (Note: For best results, the face of the
subject should be relatively large on the LCD
screen, and the subject should be facing the
camera as front on as possible.)
3. Press
4. Press
5. Press the Left/Face Detection button to turn off
Shutter halfway to focus on the subject.
Shutter fully to capture the image.
Face Detection.
Page 39
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Smile Detection
With the "Smile Detection" feature, the camera
automatically detects and captures a person
smiling.
1. In Shooting mode, press the Left/Face Detection
button to turn on Smile Detection and an icon (
) appears on the LCD.
2. Point the camera at the subject until the
subject's face is detected and bracketed by a
square box. Press the Shutter button all the
way down and release the Shutter button. The
camera will now 'wait' for the subject to smile.
3. When the subject smiles, the camera will
automatically release the shutter and capture the
photo.
4. To disable Smile Detection function, please
press Left or Shutter button.
A face must be detected by the camera in
order for smile detection to function correctly.
For optimal detection results, the subject
should be framed to occupy most of the
screen space.
3637
Page 40
Blink Detection
The Blink Detection feature is on by default, and
after taking each photo, a warning message will
pop up if a blink has been detected in the photo.
1. In any Still Shooting modes, press the
button to enter the photo menu.
2. Switch between different Photo Setup menus
and Camera Setup menus using the Left/Right
button, and select the “Blink Detection” setting
using the Up/Down button.
3. Use the Right navigation buttons to enter the
submenu, and select "On" option.
4. Press the
exit the menu.
5. Press the Shutter button fully to capture the
image. A warning message will be shown on the
LCD immediately after detecting someone has
blinked in the picture.
A face must be detected by the camera in
order for smile detection to function correctly.
For optimal detection results, the subject
should be framed to occupy most of the
screen space.
button to confirm the setting and
Page 41
PLAYBACK
1
2
3
4
5
6
Viewing Photos and Videos
To view the captured photos and video clips on the
LCD screen:
1. Press
The last recorded photo or video clip is
displayed.
2. Use the
through the photos or video clips stored in the
internal memory or memory card.
3. To play a selected video clip, press the
button to enter the movie playback mode.
During video playback, the operating instructions
will appear on the screen. Press the Left/Right button, and press the button for confirmation.
38393839
button to go to the Playback mode.
Left/Right navigation buttons to scroll
The ope ra ti ng inst ru ct ion i co ns are as
follows.
1 First Frame4 Back
2 Play5 Rewind
3 Fast Forward6Pause
Page 42
AgfaPhoto OPTIMA 3
During video playback, you can press the Up/Down
button to adjust the volume.
Thumbnail View
In Playback mode, turn the zoom control to display
thumbnails of pictures and video clips on the LCD
screen.
1. Display thumbnail with 2x2, 3x3 and 4x4 by
switching the Zoom lever.
2. Use
Up/Down/Left/Right to select a photo or
video clip to view.
If the indicator appears on the LCD, then
a movie file is currently being displayed.
Press the button to restore a preview icon
to its original image size.
Page 43
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Using Zoom Playback (for still pictures only)
When playing photo, you can also use zoom lever to
zoom in it (2~8) times.
1. Press
2. Use the
a photo to magnify.
3. Adjust the Zoom lever to the side
in the photo.
4. Use the Zoom Wheel to enlarge the image. The
zoom indication area will be shown by the icons
in the lower right corner of the display screen.
button to go to the Playback mode.
Left/Right navigation buttons to select
to zoom
5. Use the navigation buttons to pan across the
image.
6. Press the
original scale.
Movie images cannot be magnified.
button to return the image to its
4041
Page 44
Using the Delete Button
In Playback mode, you can press the Down/Delete
button to delete pictures or videos.
To delete pictures or videos:
1. Press
2. Select a picture or video clip you want to delete
with the Left/Right button.
3. Press the Down/Delete button and the delete
screen appears.
button to go to the Playback mode.
4. Select Yes or Back with Up/Down button and
press the button for confirmation.
Erased photos/video clips cannot be
recovered.
Please refer to page 52 for instructions on the
Delete Menu options.
Page 45
USING THE MENUS
Still Picture Menu
Mode: M
In any of the above Still Picture Modes, press the
button to go to the Still Picture menu.
To adjust each setting:
1. In the Still Picture menu, switch between
different Photo Setup or Camera Setup pages
using the Left/Right button, to select the page
with the function you want to adjust and press
the Down button.
2. Press the Up/Down buttons to select the
function.
4243
3. Press the Right button to go to the submenu.
4. Press Up/Down button to select an option or
press the Left or button to return to the
menu.
5. Press the
the menu.
After selecting a function, you can press the
Up button to return to the Still Picture menu
for other Photo Setup or Camera Setup pages.
Or you can press the Down button several
times to move to the next setup menu page.
Refer to the following pages for more details about
each setting.
button for confirmation and exit
Page 46
AgfaPhoto OPTIMA 3
AF Mode (Auto-Focus mode)
Use this setting to control the auto-focus
mechanism while taking pictures.
Two options are available:
Single AF: The focus frame appears on the
•
center of the LCD screen to focus on the
subject.
Multi AF: The camera uses multiple parts of the
•
picture to correctly focus.
AF Assist Beam
This option can turn on or turn off AF assist lamp.
The AF assist lamp assists the camera in focusing
correctly in low light conditions. It is not recommended that this be turned off or the camera may
not focus correctly.
Page 47
AgfaPhoto OPTIMA 3
Continuous AF
The camera continuously focuses as the subject
moves such as a sports player.
44
Expo Metering (Exposure Metering)
This setting determines what part of the picture the
camera uses to determine the correct exposure for
the whole picture.
Three options are available:
• Spot
• Center
• AiAE (Artificial Intelligence AE)
Page 48
AgfaPhoto OPTIMA 3
Continuous Shot
Use this setting to perform continuous shooting.
Once in this mode, you must continuously hold
down the Shutter button to take multiple frames.
Four options are available:
•
Continuous shooting: Press and hold the shutter to shoot continuously until you release the
shutter or when the memory card has run out
of space.
3shot: Capture up to 3 consecutive pictures.
•
•
3 shots (Last): Capture pictures continuously
until the Shutter button is released but only
the last 3 shots are recorded.
•
Time-Lapse: Automatically capture pictures in
a predefined interval.
The flash is designed not to work in this mode
in order to enable quick succession of shots.
Continuous Shot can only be selected in Selftimer Mode.
45
Page 49
AgfaPhoto OPTIMA 3
Date Imprint
Include a Date/Time stamp in the photo image.
Off
•
Date
•
Date and Time
•
46
Quick Review
This setting refers to the quick photo review
immediately after taking a picture. The picture stays
on the LCD screen for an adjustable period of time.
Four options are available:
Off
•
sec
• 1
sec
• 2
sec
• 3
Page 50
AgfaPhoto OPTIMA 3
Digital Zoom
Use this setting to enable or disable the digital
zoom function. When disabled, only the optical
zoom is enabled.
Slow Shutter
In Slow shutter mode, the shutter will remain open
as long as the Shutter button is pressed. This gives
you complete control over the duration of exposure.
(The slow shutter mode is available only in M
manual mode.)
Manual
•
The use of tripod is recommended for
prolonged exposure.
: To set a long exposure time
between 2~30 sec.
47
Page 51
AgfaPhoto OPTIMA 3
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Blink Detection
The Blink Detection feature is on by default, and
after taking each photo, a warning message will
pop up if a blink was detected in the photo.
Off
•
• On
48
4849
OIS Stabilization
Turning on the OIS Stabilization will avoid blurred
images caused by hand shake and deliver sharper
photos. (This function is not available in panorama
mode.)
• Continuous ON
• In shooting
• Off
Shooting in a windy or unstable environment
(such as moving vehicle) may cause blurred
images.
Page 52
Movie Menu
Mode:
In the Movie Mode, press the button to go to
the corresponding Movie menu.
To configure each setting:
1. In the Movie menu, switch between the Movie
Setup or different Camera Setup pages using
the Left/Right button, select the page with the
function you want to adjust and press the Down
button.
2. Press the Up/Down button to select the
function and press the Right button to go to the
submenu.
3. Press the Up/Down button to select an option or
the Left or button to return to the menu.
4. Press the
the menu.
Refer to the following pages for more details about
each setting.
button for confirmation and exit
Page 53
AgfaPhoto OPTIMA 3
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Continuous AF
The camera continuously focuses as the subject
moves such as a sports player.
50
5051
Expo Metering (Exposure Metering)
This setting determines what part of the picture the
camera uses to determine the correct exposure for
the whole picture.
Three options are available:
Spot
•
Center
•
AiAE
•
(Artificial Intelligence AE)
Page 54
Playback Menu
Mode :
In Playback mode, press the button to enter
the Playback menu.
Please refer to the following sections for detailed
instructions on the various menu options.
Protect
To prevent any pictures or videos from being
accidentally erased, use this setting to lock one or
all of the files.
To protect/unprotect a picture or video:
1. Press button and find the picture or video
you want to protect by using Left/Right button.
Once it is displayed on the screen, go to the
Playback menu and select Protect settings.
2. Use the Up/Down navigation buttons to select
One to protect this picture/video, or select All to
protect all pictures/videos in the internal memory
or memory card. Then press the Right navigation
button to enter the submenu.
Page 55
AgfaPhoto OPTIMA 3
3. Press the button to select Yes to lock. For
locked picture/video, use Unlock option to
unlock it.
4. A key (
screen to indicate that the picture/video is
protected. Select Back with Up/Down navigation
buttons to return into the Playback menu.
5. Select
remove protection for all files that have been
placed in the protected mode.
) icon will appear on the top of the
Reset on the Protection setting to
52
Delete
There are two ways to delete files.
• Delete One:
1. On the Delete setting, select One and press the
Right button.
2. Using the
or movie file to be deleted. Select Yes (to delete
file) or No (to return to the previous menu) using
the Up/Down buttons, then press the button
to confirm.
Left/Right buttons, locate the photo
Page 56
AgfaPhoto OPTIMA 3
• Delete All:
1. On the Delete setting, select
the Right button.
2. Using the
delete all files) or No (to cancel and return to the
previous menu).
Up/Down buttons, select Yes (to
The “” indicator means a file is protected.
File protection must be removed first before a
file can be deleted.
Deleting files will cause DPOF settings to be
reset.
All and then press
DPOF (Digital Print Order Format)
DPOF allows you to record your selection of
pictures that you would like to print, and will save
your selection in the memory card, so that you can
simply hand your memory card to a photo kiosk
without having to tell them in person which photos
you would like to print.
53
Page 57
AgfaPhoto OPTIMA 3
Trim
The Trim setting allows you select an area of the photo
you want to keep and then save it as a new photo.
To trim a picture:
1. Select the
2. Using the
you want to crop and have it displayed on the LCD,
that you need to press "YES" if the image is choosen.
3. Use the zoom buttons and navigation buttons
to adjust the trimming box to fit the location and
size of the new picture.
4. “Save Changes?” prompt will display after pressing
and save the image, or select “X” to cancel the
changes and return to the screen of trim prompt.
The image can not be cropped again when it is
54
cropped to 640X480.
Trim setting from the menu.
Left/Right buttons, locate the photo that
button, select “O” to confirm the changes
HDR-High Dynamic Range
With the HDR function, pictures that may be
overexposed may be corrected to optimize the
highlights and lowlights captured to more accurately
represent the real scene.
1. Select HDR setting in
previously.
2. Press Left and Right button to find picture you
want to optimize and then select Yes to perform
HDR optimization or select Return to go back to
Playback menu.
3. After using HDR function, the image will be
saved as a new file, and the original file is still
stored in the memory.
menu as described
Page 58
AgfaPhoto OPTIMA 3
Resize
This setting allows you to resize a picture to a
specified resolution, and saves it as a new picture.
1. Select the
menu as described previously.
2. Use the
a picture to resize.
3. Use the
a resolution (
the image or
Playback
4. Press the
Resizing an image creates a new file that
contains the image in the size you select. The file
with the original image also remains in memory.
Resize
setting from the
Left/Right
Up/Down
menu.
navigation buttons to select
navigation buttons to select
1024X768
Back
to cancel and return to the
button to confirm the setting.
640X480
or
Playback
) to resize
Rotate
You can use this setting to change the picture
orientation of the picture.
1. Select the
menu as described previously.
2. Use the
a picture to rotate.
3. Use the
the direction for rotation or Back to cancel and
return to the Playback menu.
4. Press the button to confirm the setting.
Rotate setting from the Playback
Left/Right navigation buttons to select
Up/Down navigation buttons to select
55
Page 59
AgfaPhoto OPTIMA 3
Red-eye Reduction
Use this setting to remove red eye in your photos.
1. Select the
as described previously.
2. Use the
from which the red eye needs to be removed.
3. Use the Up/Down navigation buttons to select
Yes to fix the selected image or Back to cancel
and return to the Playback menu.
4. Press the button to confirm the setting.
Red-eye Reduction in Playback menu
Left/Right button to select the picture
For best results, the face of the subject
should be relatively large on the LCD screen,
the subject should be facing the camera as
front on as possible, and the red eyes should
be as large as possible.
Display Setup
Mode
:
Pressbutton in Playback mode to enter Display
Setup menu.
Refer to the following sections for details of every
setting.
5657
Page 60
AgfaPhoto OPTIMA 3
Slideshow
This setting allows you to view all the stored
pictures as a slideshow.
1. Select the slideshow menu, press the right
button to enter the options menu.
2. Use the
Effect, Interval time, or Repeat and use the
/ Right
3. Use the Up/Down navigation buttons to select
Start to run the slideshow or Cancel to return to
the Playback menu.
4. Press the
Up/Down
navigation buttons to adjust the setting.
navigation buttons to select
Left
button to confirm the setting.
Wallpaper Settings
Use this setting to select your favorite picture to
use as a background on the LCD screen.
1. Press Down button to select the Wallpaper
Setting menu.
2. Press Right button, and the camera will enter the
Wallpaper Setting interface.
Page 61
AgfaPhoto OPTIMA 3
Menu Wallpaper
Use Up/Down button to select the Menu Wallpaper
option, press button to confirm or press Left
button to return to last page, and press to exit
the menu.
• User
• AgfaPhoto
• Sparkling
58
Startup Screen
Use Up/Down button to select the Startup Screen
option, press to confirm or press Left button to
return to last page, and press to exit the menu.
• User
• AgfaPhoto
Page 62
Back To Default
Use Up/Down button to select Back To Default,
press to confirm or press Left button to return
to last page, and
press to exit the menu.
• Yes
• No
AgfaPhoto OPTIMA 3
59
Page 63
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Setup Menu
Mode M
The Setup menu for the camera is available in
all modes. Each menu page can be selected by
pressing the button and switching between
menus with the Left/Right button.
To adjust the settings:
1. Select the menu page with the function you
want to adjust and press the Down button.
2. Switch between different functions with the
Up/Down button.
3. Press the
Refer to the following pages for more details about
each setting.
Right button to enter the submenu.
After selecting a function option, you can
press the Up button to return to the menu for
other Camera Setup pages. Or you can press
the Down button to switch to the next menu
page.
6061
Page 64
AgfaPhoto OPTIMA 3
Beep
Use this setting to adjust the volume of beep when
buttons are pressed and change the tones for
Shutter button, self-timer, and power-on/power-off.
To change this setting:
1. Select the
described previously.
2. Use the
between volume, shutter tone, key tone, selftimer tone, and power tone fields.
3. Press the Right button, press the Up/Down
button to adjust volume and change tone, and
press the button to confirm setting.
Beep
Up/Down
setting from the
navigation buttons to switch
Setup
menu as
LCD Brightness
Use this setting to adjust the brightness of your
LCD screen.
1. Select the
Setup menu as described previously.
2. Select auto or adjust the brightness level using
the Left/Right button, and press the button
to confirm the setting.
LCDBrightness setting from the
61
Page 65
AgfaPhoto OPTIMA 3
Power Saver
This setting allows you to save power and get
the maximum possible running time for your
battery. Follow the steps below to turn off the LCD
screen and camera automatically after a period of
inactivity.
1. Select the
menu as described previously.
2. Press the Up/Down button to select the power
items for the screen and camera and press the
Right button.
3. Press the Up/Down button to adjust the
selected item. Both items have the following
options:
62
6263
PowerSave setting from the Setup
• Turn off the LCD:
30 sec, 1 min, 2 min, and off.
• Turn off the camera:
3 min, 5 min, 10 min, and off.
4. Press the button to confirm.
Zone
The Zone setting is a useful function on your
overseas trips. This feature enables you to display
the local time on the LCD screen while you are
overseas.
1. Select the
as described previously. The world time screen
appears.
2. Use the
between the hometown ( ) and travel
destination ( ) fields.
3. Use the
a city close to the desired time zone. Then press
the button to confirm.
Zone setting from the Setup menu
Up/Down navigation buttons to switch
Left/Right navigation buttons to select
Page 66
Date/Time
Setting the Date and Time
See “
15.
Language
Setting the Language
See “
“ section on page
“ section on page 16.
AgfaPhoto OPTIMA 3
File and Software
Format Memory
Please note: formatting enables you to delete all
contents in the memory card and built-in memory,
including protected photo and movie files.
To use this setting:
1. Select the Format in File and Software menu.
2. Use the
Yes
3. The current media is formatted.
Up/Down
or No. Then press the button to confirm.
navigation buttons to select
Page 67
AgfaPhoto OPTIMA 3
File Numbering
After you take a picture or video clip, the camera
will save it as file that ends with a serial number.
You can use this item to choose whether the file
is consecutively numbered or begins with 1 and is
saved in another folder on the memory card.
1. Select the File Name in File and Software menu.
2. Select the option with the Up/Down button and
press the button for confirmation.
64
Copy to Card (Copy internal memory to
memory card)
Use this setting to copy the files stored in the
internal memory to the memory card.
1. Select the Copy to memory card in File and
Software menu.
2. Use the Up/Down navigation buttons to select
Yes or No. Then press the button to confirm.
Page 68
AgfaPhoto OPTIMA 3
Reset Settings
Use this setting to restore the camera to its default
settings.
1. Select the Reset setting in File and Software
menu.
2. Use the Up/Down navigation buttons to select
Yes or No. Then press the button to confirm.
FW Version (Firmware Version)
Use this setting to view the current camera
firmware version.
1. Select the
menu.
2. If SD card contains a new version of firmware,
please upgrade accordingly as necessary.
To inform to the latest firmware version, you
can go to the following website
www.plawa.com
FW Version
in File and Software
65
Page 69
Transmission
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Video System
Use this setting to determine your video system in
the current area.
1. Select the Video System in Connection
Transmission menu.
2. Use the Up/Down navigation buttons to select
NTSC or PAL. Then press the button to
confirm.
The video output signal can be switched to NTSC or
PAL to accommodate different regional standards.
The appropriate setting will vary between regions.
NTSC: USA, Canada, Taiwan, Japan, etc.
PAL:
Note:
Europe, Asia (excluding Taiwan), Oceania,
etc.
The TV output will not display properly if an
incorrect video system is selected.
66676667
Page 70
Connecting to a PC
Use the USB cable supplied with your camera to
copy (transfer) pictures to a computer.
Setting the USB Mode
Since the camera’s USB port can be set to connect
with either a PC or a Printer, the following steps
will allow you to ensure that the camera is correctly
configured to connect with a PC. The USB mode is
set to PC by default.
1. Go to the transmission menu, select USB
connection with the Up/Down button, and press
the Right button.
.
Up/Down
navigation buttons to select
2. Use the
PC
3. Press the button to confirm the setting.
Transferring Files to Your PC
The computer will automatically detect the camera
as a removable drive. Double-click My
on the desktop to locate the removable drive and to
copy the folders and files in the drive to a directory
on your PC as you would copy any other folder or file.
By using the USB cable, you can transfer the
captured photos and videos to a PC. Follow the
steps below to connect the camera to a PC.
1. Make sure both the camera and PC are turned on.
2. Connect one end of the supplied USB cable to
the USB/AV OUT port on your camera.
3. Connect the other end of the cable to an
available USB port on your PC.
Computer
icon
Page 71
AgfaPhoto OPTIMA 3
Windows operating system (Windows 2000,
Windows XP, Windows Vista, Windows 7.)
Click the [Safely remove the hardware] icon and
remove the USB connector according to the
appeared menu.
4. Disconnect the camera once transfer is
completed.
If the USB option is set to [PC]
Turn the camera off and disconnect the USB cable.
:
Macintosh
Drag the untitled icon to the Trash. ("Untitled")
If the USB option is set to [PC (PTP)] :
Remove the camera from the system as described
below before turning the camera off and
disconnecting the USB cable.
68
6869
Page 72
APPENDICES
Specifications: OPTIMA 3
Design and specifications are subject to change without notice.
Dimensions (W x H x D)98.5mm x 57.3mm x (21~24.8)mm
MassApprox. 146g (Body only)
72
7273
Eye Reduction+Slow Synchro
Shooting Range Wide: Approx. 0.3m~5.1m / Tele: Approx. 1.0m ~ 2.8m
(ISO 800)
Internal Memory: 32 MB (12 MB available to store images and videos)
SD Card/SDHC Card (Up to 16GB support)
Approx. 180 shots (based on CIPA Standards)
Page 76
Error messages
MessagesExplanation
No card• The memory card is not inserted.
Card error• The memory card is not formatted.
Card full• The memory card is full and cannot store any new images.
Write protect• The memory card is write-protected.
Picture error• The picture is not captured correctly.
• The picture is corrupted.
No picture• There are no images in the memory card or in the internal memory.
Lens error• The lens is probably stuck and the camera will power off automatically.
System error• Unexpected error encountered.
Image cannot be saved• The write protection switch in the memory card is set to the “LOCK”
Out of the range• When pictures were taken in Panorama mode, the direction of move-
position.
ment was incorrect.
Page 77
AgfaPhoto OPTIMA 3
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
MessagesExplanation
Card is not formatted, format?• Confirm whether the memory card should be formatted.
This image cannot be deleted• The picture or video you are trying to delete is protected.
Cannot record movie• The write protection switch in the memory card is set to the “LOCK”
Warning!! Camera recording,
please wait.
Warning!! Battery exhausted.• The battery is drained.
This file cannot be played back• The picture format cannot be recognized by the camera.
No connection• The camera is not connected to the printer correctly.
Print error• There is a problem with camera or printer.
Cannot print• Check that the printer is out of paper or out of ink.
74
7475
position.
• No other actions allowed to perform during video/audio recording.
• Check if the printer has a paper jam.
Page 78
Troubleshooting
ProblemPossible causesSolution
Camera does not turn on.• The battery has run out.
• The battery is not inserted
correctly.
Camera turns off suddenly
during operation.
The picture is blurred.• The lens is dirty.
Images and video files cannot
be saved.
No picture is taken when
pressing the Shutter button.
• The battery has run out.• Replace with a fully charged battery.
• appears when taking
pictures.
• The memory card is full. • Replace the memory card with a new
• The memory card is full.
• No available space to store
the files.
• The mode dial is in Playback
mode.
• Replace with a fully charged battery.
• Use a soft cloth to clean the lens on
your camera
• Use the OIS mode.
one.
• Delete unwanted images.
• Unlock the memory card.
• Replace the memory card with a new
one or clean off current memory card.
• Delete unwanted images.
• The memory card is locked.
Page 79
AgfaPhoto OPTIMA 3AgfaPhoto OPTIMA 3
Customer Care
More information on the complete AgfaPhoto digital
camera product range can be found at
www.plawa.com / www.agfaphoto.com.
Service & Repair Hotline (EU):
00800 752 921 00 (from a landline only)
Service & Repair (UK):
+44 1908 488676, info@allmondegroup.com
Service & Support Hotline (Germany):
0900 1000 042 (1.49 euro / min. from a German
landline only)
Online Service / International contact:
support-apdc@plawa.com
Manufactured by
plawa-feinwerktechnik GmbH & Co. KG
Bleichereistraße 18
73066 Uhingen
Germany
Allmonde Group Limited, 218 Fairbourne Drive, Atterbury, Milton Keynes, MK10 9RG, United Kingdom
AgfaPhoto is used under license of Agfa-Gevaert
NV & Co. KG or Agfa-Gevaert NV. Neither Agfa-Gevaert NV & Co KG nor Agfa-Gevaert NV manufacture this product or provide any product warranty
or support. For service, support and warranty
information, contact the distributor or manufacturer.
All other brands and product names are registered
trademarks of their respective owners. Product design and technical features can be changed without
notice. Contact: AgfaPhoto Holding GmbH, www.
agfaphoto.com
7677
Page 80
Agfa Photo i s used u nder li cense o f Agfa- Gevaer t NV & C o. KG or A gfa-Ge vaert NV. Neit her Agf a-Geva ert NV & Co. KG n or Agfa -Geva ert NV m anufa cture t his pro duct o r provi de any pr oduct warran ty or s upport .
For s ervic e, supp ort and warra nty inf ormati on, con tact t he dist ributo r or man ufact urer. Fo r serv ice, sup port a nd warr anty i nforma tion, c ontac t the dis tribu tor or ma nufac turer. A ll othe r bran ds and pr oduct
name s are re giste red tra demark s of the ir resp ectiv e owner s. Pro duct de sign an d techn ical fe atures can be c hanged withou t notic e.
Agfa Photo H olding GmbH, w ww.ag faphot o.com
Manu factu red by p lawa-f einwer ktech nik GmbH & Co. KG, www.p lawa.c om
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.