Thank you for choosing a first class product from Electrolux, which hopefully will
provide you with lots of pleasure in the future. The Electrolux ambition is to offer a
wide variety of quality products that make your life more comfortable. You find
some examples on the cover in this manual. Please take a few minutes to study
this manual so that you can take advantage of the benefits of your new machine.
We promise that it will provide a superior User Experience delivering Ease-ofMind. Good luck!
Contents
Safety information..............................5
Product description ...........................6
Control panel.....................................7
In the interest of your safety and to
ensure the correct use, before
installing and first using the
appliance, read this user manual
carefully, including its hints and
warnings. To avoid unnecessary
mistakes and accidents, it is
important to ensure that all people
using the appliance are thoroughly
familiar with its operation and safety
features. Save these instructions
and make sure that they remain
with the appliance if it is moved or
sold, so that everyone using it
through its life will be properly
informed on appliance use and
safety.
General safety
● It is dangerous to alter the
specifications or attempt to modify
this product in any way.
● During high temperature wash
programmes the door glass may get
hot. Do not touch it!
● Make sure that small pets do not
climb into the drum. To avoid this,
please check into the drum before
using.
● Any objects such as coins, safety
pins, nails, screws, stones or any
other hard, sharp material can cause
extensive damage and must not be
placed into the machine.
● Only use the advised quantities of
fabric softener and detergent.
Damage to the fabric can ensue if
you over-fill. Refer to the
manufacturer’s recommendations of
quantities.
● Wash small items such as socks,
laces, washable belts etc in a
washing bag or pillow case as it is
possible for such items to slip down
between the tub and the inner drum.
● Do not use your washer-dryer to
wash and dry articles with
whalebones, material without hems
or torn material.
● Always unplug the appliance and
turn off the water supply after use,
cleaning and maintenance.
● Under no circumstances should you
attempt to repair the machine
yourself. Repairs carried out by
inexperienced persons may cause
injury or serious malfunctioning.
Contact your local Service Centre.
Always insist on genuine spare parts.
Installation
● This appliance is heavy. Care should
be taken when moving it.
● When unpacking the appliance,
check that it is not damaged. If in
doubt, do not use it and contact the
Service Centre.
● All packing and transit bolts must be
removed before use. Serious
damage can occur to the product
and to property if this is not adhered
to. See relevant section in the user
manual.
● After having installed the appliance,
check that it is not standing on the
inlet and drain hose and the worktop
is not pressing the electrical supply
cable.
● If the machine is situated on a
carpeted floor, please adjust the feet
in order to allow air to circulate freely
under the appliance.
4 electrolux safety information
● Always be sure, that there is no
water leakage from hoses and their
connections after the installation.
● If the appliance is installed in a
location subject to frost, please read
the “dangers of freezing”chapter.
● Any plumbing work required to install
this appliance should be carried out
by a qualified plumber or competent
person.
● Any electrical work required to install
this appliance should be carried out
by a qualified electrician or
competent person.
Use
● This appliance is designed for
domestic use. It must not be used
for purposes other than those for
which it was designed.
● Only wash fabrics which are
designed to be machine washed.
Follow the instructions on each
garment label.
● Do not overload the appliance. See
the relevant section in the user
manual.
● Before washing, ensure that all
pockets are empty and buttons and
zips are fastened. Avoid washing
frayed or torn articles and treat
stains such as paint, ink, rust, and
grass before washing. Underwired
bras must NOT be machine washed.
● As some duvets and eiderdowns
should be washed/dried in large
commercial machines because of
their bulk, please check with the
manufacturer of the item before
washing in a domestic machine.
● The users should always check that
they have not left their gas lighters
(disposable or otherwise) in their
clothing.
●
Never tumble dry items that have
had contact with chemicals such as
dry cleaning fluid.These are of a
volatile nature and could cause an
explosion.
Only tumble dry items which have
been washed in water or require airing.
●
Plastic detergent dispensers should
not remain in the drum during the
drying cycle, as the plastic used is
not designed to withstand the heat.
If you wish to wash-through-to-dry
you should use the conventional
detergent dispenser drawer.
● Garments which have been in
contact with volatile petroleum
products should not be machine
washed. If volatile cleaning fluids are
used, care should be taken to
ensure that the fluid is removed from
the garment before placing in the
machine.
● Never pull the power supply cable to
remove the plug from the socket;
always take hold of the plug itself.
● Never use the appliance if the power
supply cable, the control panel, the
working surface or the base are
damaged so that the inside of the
washer dryer is accessible.
● Leave the porthole door slightly ajar
between washes to preserve the
door seal.
Child safety
● This appliance is not intended for
use by person (including children)
with reduced physical sensory or
mental capabilities or lack of
experience and knowledge unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible
for their safety.
● The packaging components (e.g.
plastic film, polystyrene) can be
dangerous to children - danger of
suffocation! Keep them out of
children’s reach
● Keep all detergents in a safe place
out of children’s reach.
● Make sure that children or pets do
not climb into the drum. To prevent
children or pets becoming trapped
inside, this the machine incorporates
special feature. To activate this
device, rotate the button (without
pressing it) inside the door clockwise
until the groove is horizontal. If
necessary use a coin.
safety information electrolux 5
P1131
To disable this device and restore
the possibility of closing the door,
rotate the button anti-clockwise until
the groove is vertical.
6 electrolux product description
Product description
Your new appliance meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption.
The ECO valve system allows total use of detergent and reduces water
consumption therefore saving energy.
1
Detergent dispenser drawer
2
Control panel
3
Door opening handle
4
Rating plate
5
Drain pump
6
Adjustable feet
Detergent dispenser drawer
Compartment for detergent used
for prewash. The prewash
detergent is added at the
beginning of the wash
programme.
Compartment for powder or liquid
detergent used for main wash.
Compartment for liquid additives
(fabric softener, starch)
EN001
control panel electrolux 7
1234678510
9
Control panel
Below is a picture of the control panel. It shows the programme selector dial as
well as the buttons, pilot lights and the display. These are presented by relevant
numbers on the following pages.
1
Programme selector dial
2
Temperature button
3
Spin reduction button
4
Extra Rinse button
5
Drying Time button
6
Delay Start button
7
Display
8
Start/Pause button
9
Door locked pilot light
10
Time Manager buttons
8 electrolux control panel
Display (7)
7.3
7.1
Duration of selected
programme/
After selecting a programme, the
duration is displayed in hours and
minutes (for example
duration is calculated automatically on
the basis of the maximum
recommended load for each type of
fabric. After the programme has
started, the time remaining is updated
every minute.
/Selected drying time
After selecting a drying programme, the
drying time is displayed
hours and minutes (e.g 130 mins =
2.05). The
in minutes or in
7.4
2.10 ).
After the programme has started the
time remaining is updated every
minute.
/Delayed start
The selected delay set by pressing the
relevant button appears on the display
7.1
2.05
7.2
for a few seconds, then the duration of
the previously selected programme is
displayed.
/Alarm codes
In the event of operating problems,
some alarm codes can be displayed,
for example
do if...»).
/Incorrect option selection
If an option which is not compatible
with the set wash programme is
selected, the message Err is displayed
for a few seconds and the integrated
red light of button 8 starts blinking.
/End of programme
When the programme has finished
three blinking zeros
the pilot light 9 and the pilot light of
button 8 go out and the door can be
opened.
E20 (see chapter «What to
0.00 are displayed,
control panel electrolux 9
7.2
Washing phase icons
By selecting the wash programme, the
washing programme phase icons
corresponding to the various phases
making up the programme are shown
in the bottom of the display.
= washing
= rinsing
= draining
= spinning
= drying
After the machine has started, only the
running icon stays on. When the
programme has finished, the flashing
0.00) is displayed.
zero (
7.3
Soil level icons
When selecting a programme on the
display appears an icon indicating the
degree of soiling automatically
proposed by the machine.
7.4
Child lock
This function allows you to leave the
appliance unsupervised during it’s
functioning.
Door locked light (9)
The pilot light
that the appliance starts operating and
the door is locked.
This light indicates if the door can be
opened:
• light on: the door cannot be opened.
• blinking: the door is opening in a few
minutes.
• light off: the door can be opened.
9 illuminates to indicate
10 electrolux use
Use
First Use
● Ensure that the electrical and water
connections comply with the
installation instructions.
● Remove the polystyrene block and
any material from the drum.
● Pour 2 litres of water into the main
wash compartment of the
detergent drawer in order to activate
the ECO valve. Pour 1/2 a measure
of detergent into the dispenser
drawer and start the machine. Then
run a cotton cycle at 90°C, without
any laundry in the machine, to
remove any manufacturing residue
from the drum and tub.
Acoustic signals
The machine is provided with an
acoustic device, which sounds in the
following cases:
● at the end of the cycle
● if there is a fault
By pressing buttons
simultaneously for about 6 seconds,
the acoustic signal is deactivated
(except if there is a fault).
By pressing these 2 buttons again, the
the acoustic signal is reactivated.
Child safety lock
This function allows you to leave the
appliance unsupervised and not to
worry that children might be injured by
or cause damage to the appliance.
This function remains able also when
4 and 5
the washing machine is not working.
There are two different ways to set this
option:
1
before pressing button 8: it will be
impossible to start the machine.
2
after pressing button
8: it will be
impossible to change any other
programme or option.
To enable or disable this option press
buttons
5 and 6 simultaneously for
about 6 seconds until on the display,
the icon appears or disappears.
Daily Use
Load the laundry
Open the door by carefully pulling the
door handle outwards. Place the
laundry in the drum, one item at a time,
shaking them out as much as possible.
Close the door.
P0004
Measure out the detergent and the
fabric softener
Pull out the dispenser drawer until it
stops. Measure out the amount of
detergent required, pour it into the
main wash compartment and, if
you wish to carry out the prewash,
pour it into the compartment marked
.
C0064
use electrolux 11
Attention!
If you turn the programme selector dial
to another programme when the
machine is working, the red light of
button
8 will blink 3 times and the
message Err will appear on the display
to indicate a wrong selection. The
machine will not perform the new
selected programme.
If required, pour fabric softener into the
compartment marked (the amount
used must not exceed the “MAX” mark
in the drawer). Close the drawer gently.
C0065
Select the required programme by
turning the programme selector
dial (1)
Turn the programme selector dial to
the required programme.
The light of button
8 starts to flash and
the display shows the duration of the
selected programme.
The selector dial can be turned either
clockwise or anticlockwise. Turn to
position O to Reset programme/
Switch OFF the machine.
For the description of each of the
washing programmes on the
selector dial, consult the chapter
«Washing programmes».
At the end of the programme the
selector dial must be turned to
position O, to switch the machine
off.
Programme Option buttons
Depending on the programme, different
functions can be combined. These
must be selected after choosing the
desired programme and before
pressing the button
8.
When these buttons are pressed, the
corresponding pilot lights illuminate.
When they are pressed again, the pilot
lights go out.
If an incorrect option is selected, the
integrated red pilot light of the button
flashes 3 times and the Err message
appears on the display for some
seconds.
For the compatibility among the
washing programmes and the
options see chapter «Washing
Programmes».
Select the temperature by pressing
button
2
Press this button repeatedly to
increase or decrease the temperature,
if you want your laundry to be washed
at a temperature different from the one
proposed by the washer-dryer.
Select the spin speed, Rinse Hold
or No Spin option
by pressing
button 3
Press button 3 repeatedly to change
the spin speed, if you want your
laundry to be spun at a speed different
8
12 electrolux use
from the one proposed by the washerdryer. The relevant light will light up.
When you select a programme, the
machine automatically proposes the
maximum spin speed provided for the
programme.
Rinse Hold: by selecting this option
the water of the last rinse is not
emptied out to prevent the fabrics from
creasing. When the programme has
finished the display shows
flashing, the pilot light 9 is on, the light
of button 8 is off. The door is locked to
indicate that the water must be
emptied out.
To empty the water out, please
read the chapter «At the end of the
programme».
No spin : by selecting this option, all
spinning phases are suppressed and
replaced by a drain, so as not to
wrinkle the laundry. Recommended for
extremely delicate fabrics.
On some programmes the rinses will
be performed with more water.
Select the Extra Rinse option by
pressing button
The machine performs some additional
rinses. This option is recommended for
people who are allergic to detergents,
and in areas where the water is very
soft.
Select the Drying Time
button
If you wish to carry out a timed drying
programme, press this button until the
drying time you want appears on the
display according to the fabrics (cottons or synthetics) you have to dry.
For Cottons you can select a drying
time from 10 minutes to 250 minutes
(4.10).
5
4
0.00
by pressing
For Synthetics you can select a drying
time from 10 minutes to 130 minutes
(2.10).
Every time you press this button the
drying time increases by 5 mins.
Select the Delay Start by pressing
button
Before you start the programme, if you
wish to delay the start, press button 6
repeatedly, to select the desired delay.
The relevant light will illuminate.
The selected delay time value (up to 20
hours) will appear on the display for a
few seconds, then the duration of the
programme will appear again.
You must select this option after you
have set the programme and before you
press button
The door will be locked throughout the
delay time. If you wish to add laundry in
the machine during the delay time press
button
and wait until the pilot light 9 goes out
before opening the door. Add the
laundry, close the door and press the
button 8 again.
You can cancel or modify the delay time
at any moment, before you press
button
The wash programme can be delayed
from 30 min - 60 min - 90 min, 2 hours
and then by 1 hour up to a maximum of
20 hours by means of this button.
Selecting the delayed start.
• Select the programme and the
• Select the delay start.
• Press button
The programme will start after the
selected delay has expired.
6
8.
8 to put the machine in pause
8.
required options.
8: the machine starts its
hourly countdown.
use electrolux 13
Cancelling the delayed start after having
started the machine
• Press button
• Press button
8.
6 once until the symbol
0’ is displayed.
• Press button
The Delay Start can not be selected
with Drain programme.
Select the Start/Pause by pressing
button
8
To start the selected programme, press
button 8; the green pilot light stops
flashing.
To interrupt a programme which is
running, press button
light starts to flash.
To restart the programme from the point
at which it was interrupted, press
button 8 again.
If you have chosen a delayed start, the
machine will begin the countdown.
If an incorrect option is selected, an
integrated red pilot light of button
flashes 3 times the message Err is
displayed for a few seconds.
Select the Time Manager option by
pressing buttons 10
This function allows you to modify the
washing time, automatically proposed
by the washer-dryer.
By pressing this button repeatedly, the
duration of the washing cycle can be
increased or decreased.
A soil level icon will appear on the
display to indicate the chosen degree of
soiling.
8 again.
8: the green pilot
8
Soil
Level
IntensiveFor heavy soiled items
NormalFor normal soiled items
DailyFor daily soiled items
LightFor slightly soiled items
QuickFor very slightly soiled items
Super
Quick (*)
(*) We recommend that you reduce the load
IconType of fabric
For items used or worn for a
short time
sizes (see «Washing programmes»).
Attention!
This option cannot be selected with the
Economy cottons programmes.
The availability of these soil level icons
change according to the type of fabric
as shown in the following chart:
FabricSoil Level
Intensive NormalDailyLightQuickS. Quick
Cottons
95°-90°C
60°C
50°C
40°C
30°C
Synthetics
60°C
50°C
40°C
30°C
Delicates
40°C
30°C
XXXXXX
XXXXXX
XXXXXX
XXXXXX
XXXXXX
XXXX
XXXX
XXXX
XXXX
XXXX
XXXX
Altering an option or a running
programme
It is possible to change some options
14 electrolux use
before the programme carries it out.
Before you make any change, you must
pause the washer-dryer by pressing
button 8.
(Only the Time Manager option cannot
be modified after the programme has
started. )
Changing a running programme is
possible only by resetting it. Turn the
programme selector dial to O and then
to the new programme position. Start
the new programme by pressing button
8 again. The washing water in the tub
will not be emptied out.
Interrupting a programme
Press button
programme which is running, the
corresponding light starts to flash. Press
the button again to restart the
programme.
Cancelling a programme
Turn the selector dial to O to cancel a
programme which is running. You can
now select a new programme.
Opening the door after the
programme has started
First set the machine to pause by
pressing button
If the light 9 blinks and then goes off,
the door can be opened.
If the light 9 remains lit, this means
that the machine is already heating,
that the water level is too high.
In this case the door can not be
opened.
If you cannot open the door but you
need to open it you have to switch the
machine off by turning the selector dial
to O. After a few minutes the door can
be opened (pay attention to the
water level and temperature!).
8 to interrupt a
8.
After closing the door, it is necessary to
select the programme and options
again and press button 8.
At the end of the programme
The machine stops automatically, the
pilot light of button
8 goes off and
three blinking «0.00» will appear on the
display. The buzzer sounds.
If a programme with an option that
ends with water still in the tub has
been selected, the pilot light
9 remains
lit and the door is locked to indicate
that the water must be emptied out
before opening the door.
To empty out the water:
● turn the programme selector dial to
O
● select the Drain or the Spin
programme
● reduce the spin speed if needed, by
pressing the relevant button
● press button 8
At the end of programme,
shows 3 flashing zeros «
the display
0.00». the pilot
lights 9 goes off and the door can be
opened.
Stand by: once the programme has
finished after a few minutes the energy
saving system will be enabled. The
brightness of the display is reduced. By
pressing any button the appliance will
come out of the energy saving status.
Turn the programme selector dial to O
to switch the machine off.
Remove the laundry from the drum and
carefully check that the drum is empty.
If you do not intend to carry out
another wash, close the water tap.
Leave the door open to prevent the
formation of mildew and unpleasant
smells.
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.