Adtran T1-FT1, T1 NEBS NIM Quick Start Guide

For more detailed documentation, visit us online at www.adtran.com

NETVANTA T1/FT1 NETWORK INTERFACE MODULE (NIM) P/N 1200862L1

WAN-T1 DBU

PECIFICATIONS

T1/FT1 Interface

Clock Source Network, Internal Diagnostics

Line Rate: 1.544 Mbits/s +/- 75 bps Line Code: AMI or B8ZS Framing: D4 (SF) or ESF FT1 Line Rate: DS0 Channelized (m ulti ples of 56/64 kbps) Input Signal: 0 to -36 dB (DS-1) Line Build-Out: 0, 7.5, 15, 22.5 dB Connector: RJ-48C DS0 Assignment: Programmable

Test pattern generat ion and detection: QRSS, 511

Network loopbacks (local & remote). Responds to both INBAND and FDL loop codes.

Alarm generation and detec t io n Network and user sets of perfo r mance data

(15 min. and 24 hr.)

WAN-T1 N P

INOUT

Pin Name Description

ETWORK

(RJ-48C) C

ONNECTION

1 R1 Receive data from the network 2 T1 Receive data from the network 3 — UNUSED 4 R Transmit data toward the network 5 T Transmit data toward the network 6-8 — UNUSED

DBU (RJ-48C) C

Pin Name Description

ONNECTION PINOUT

1-3 — UNUSED 4T Network-Tip

NSTALLATION INSTRUCTIONS

1. Remove the power from the unit.

2. Slide the option module into the option slot until the module is firmly seated against the front of the chassis.

3. Secure the pins at both edges of the module.

4. Connect the cables to the associated device(s).

5. Complete installation of the Base Unit.

6. Restore power to the unit.

5 R Network-Ring 6-8 — UNUSED

An optional Dial Backup Interface Module (DIM) is required for dial backup applications.

For more detailed documentation, visit us online at www.adtran.com

NETVANTA T1/FT1 NETWORK INTERFACE MODULE (NIM) P/N 1200862L1

T1/FT1 NIM C

description

Comment line to provide an identifier for this interface (for example, circuit ID, contact information, etc.)

<text>

Up to 80 alphanumeric characters

<AMI, B8ZS>

coding

Configures the line coding for the T1 interface

<AMI>

<B8ZS>

framing

Configures the framing format of the T1 interface <D4> Super Frame T1 framing

<ESF>

shutdown

Turns off the interface. The no version of this command turns the interface on and allows it to pass data.

tdm-group Creates a group of contiguous DS0s on this interface to be used

during the cross-connect process. <number> Number to identify this group

clock source < Configures the source of the clock for the system

<P511, QRSS>

show

Displays current pattern error count

lbo

<0*, -7.5, -15, -22.5>

Sets the line build out (in dB) for the T1 Interface

OMMANDS

<text>

Alternate Mark Inversion Bipolar Eight Zero Substitution

<D4, ESF>

Extended Super Frame T1 framing

Number of DS0s in this group in the form

(starting DS0

Line, Internal, Through>

Recovers clock from the T1 circuit Use the internal clock source Recovers clock from the T1 circuit connected

to the DSX-1 port

timeslot

ending DS0)

remote-loopback

Configures the unit to accept and respond to received loopback codes on the T1interface

The no version of this command configures the interface to ignore T1 loop commands.

fdl <ANSI, ATT, NONE> Configures the format of the facility data link on the T1

loopback

Initiates a loopback on the interface

<DUAL, LOCAL, NETWORK, REMOTE>

<DUAL>

test-pattern

Initiates test pattern generation from the unit

<511> <QRSS>

test-pattern insert Inserts and error into currently a ctive te st pattern

test-pattern clear

Clears the test pattern error count

snmp trap line-status

Enables the unit to respond and transmit line status change traps

snmp trap link-status

Enables the unit to respond and transmit link up/down status traps

Configures the fdl for ANSI T1.403 standard Configures the fdl for ATT TR54016 standard No fdl standard configured

Physical loopback of the T1 circuit and inward loopback toward DTE (Network and Local)

Inward loopback toward DTE Physical loopback of the T1 circuit Sends a loop code over the T1 to the remote unit

<P511, QRSS, ONES, ZEROS>

Repeating pattern of ones and zeros Random pattern of ones and zeros

* INDICATES DEFAULT VALUES