ADTRAN T1-FT1 User Manual

NetVanta T1/FT1 + DSX-1 Network Interface Module (NIM) P/N 1202863L1

Quick Start Guide

WAN-T1 DSX-1 DBU

SPECIFICATIONS

Operating Modes T1/FT1 Interface

DSX-1 Interface

Clock Source Network, internal, and through Diagnostics

Compliance FCC Part 15 Class A, EN 55022 Class A

Physical Dimensions: 2.75-inch W x 4.25-inch D

Frame Relay, Multilink Frame Relay, PPP, Multilink PPP, HDLC Supported Standards: AT&T TR 62411, AT&T TR 54016, Bellcore TR.194, ANSI T1.403 Line Rate: 1.544 Mbps ±75 bps Line Code: AMI or B8ZS Framing: D4 (SF) or ESF FT1 Line Rate: DS0 channelized (multiples of 56/64 kbps) Input Signal: 0 to -36 dB (DS1) Line Build-Out: 0, -7.5, -15, -22.5 dB (long), 0 to 655 ft (short) Connector: RJ-48C DS0 Assignment: Programmable Supported Standards: ANSI T1.102 Line Rate: 1.544 Mbps DSX Receiver Input Range: -10 dBdsx to +6 dBdsx Capacity: 1 to 24 DS0s Line Codes: AMI, B8ZS DSX-1 interface to PBX Framing: D4 (SF) or ESF Line Length: 0 to 655 ft and -7.5 dB Connector: RJ-48C

Test Pattern Generation and Detection: QRSS, 511, 2

- 1, all ones, all zeros

2 Network loopbacks (local and remote); responds to both inband and FDL loop codes (T1 interface only) Alarm generation and detection Network and user sets of performance data (15 minutes and 24 hours)

ACTA/FCC Part 68, IC CS-03 UL/CUL 60950

Operating Temperature: 0°C to 50°C Storage Temperature: -20°C to 70°C Relative Humidity: Up to 95 percent, noncondensing

For more detailed documentation, visit us online at www.adtran.com.

INSTALLATION INSTRUCTIONS

1. Remove the power from the unit.

2. Slide the option module into the option slot until the module is firmly seated against the chassis.

3. Secure the pins at both edges of the module.

4. Connect the cables to the associated device(s).

5. Complete installation of the base unit.

6. Restore power to the unit.

For NetVanta modules with outside plant connections, ensure that all cables ar e removed from the module befor e installing or re moving it from the NetVanta chassis.

NetVanta modules should be installed only in NetVanta Series products.

WAN-T1 NETWORK (RJ-48C) CONNECTION PINOUTS

Pin Name Description

1 R1 Receive data from the network - Ring 1 2 T1 Receive data from the network - Tip 1 3 — Unused 4 R Transmit data toward the network - Ring 5 T Transmit data toward the network - Tip

6-8 — Unused

DSX-1 (RJ-48C) CONNECTION PINOUTS

- 1,

Pin Name Description

1 R Transmit data toward the DTE- Ring 2 T Transmit data toward the DTE - Tip 3 — Unused 4 R1 Receive data from the DTE - Ring 1 5 T1 Receive data from the DTE - Tip 1

6-8 — Unused

An optional Dial Backup Interface Module (DIM) is required for dial backup applications. For a description of the DBU pinouts, refer to the Quick Start Guide included with your DIM shipment.

NetVanta T1/FT1 + DSX-1 Network Interface Module (NIM) P/N 1202863L1

Quick Start Guide

T1/FT1 + DSX-1 NIM COMMANDS

clock source [internal | line* | through]

Configures the source timing used for the interface. Use the no form of this command to return to the default value.

internal Configures the unit to provide clocking using the internal oscillator. line* Configures the unit to recover clocking from the T1 circuit.

through Configures the unit to recover clocking from the circuit connected to the

coding [ami | b8zs*]

Configures the line coding for a T1 physical interface. This setting must match the line coding supplied on the circuit by the service provider.

ami Configures the line coding for alternate mark inversion (AMI).

b8zs fdl [ansi* | att | none]

Configures the format for the facility data link (FDL) channel on the T1 circuit. Use the no form of this command to return to the default value.

ansi att Configures the FDL for AT&T TR 54016 standard. none Disables FDL on this circuit. framing [d4 | esf*]

Configures the framing format for the T1 interface. This parameter should match the framing format supplied by your network provider. Use the no form of this command to return to the default value.

d4 Specifies D4 superframe (SF) format.

esf lbo [long <-22.5, -15, -7.5- 0> | short <0 to 655>]

Configures the line build out (LBO) for the T1 interface. Use the no form of this command to return to the default value.

long <-22.5, -15, -7.5- 0> Configures the LBO (in dB) for T1 interfaces with cable lengths greater short <0 to 655> Configures the LBO (in feet) for T1 interfaces with cable lengths less than

loopback network [line | payload]

Initiates a loopback on the interface toward the network. Use the no form of this command to deactivate the loopback.

line Initiates a metallic loopback of the physical T1 network interface. payload Initiates a loopback of the T1 framer (CSU portion) of the T1 network

loopback remote line [fdl | inband]

Sends a loopback code to the remote unit to initia te a line loo pba ck. Use the no form of this command to send a loopdown code to the remote unit to deactivate the loopback.

fdl Uses the facility data link (FDL) to initiate a full 1.544 Mbps physical

inband Uses the inband channel to initiate a full 1.544 Mbps physical physical

loopback remote payload

Sends a loopback code to the remote unit to i nitiate a p ayload loopb ack. A payload loopback is a 1.536 Mbps loopback of the payload data received from the network maintaining bit-sequence integrity for the information bits by synchronizing (regenerating) the timing. Use the no form of this command to send a loopdown code to the remote unit to deactivate the loopback.

remote-alarm [rai]

Selects the alarm signaling type to be sent when a loss of frame is detected on the T1 receive signal. Use the no form of this command to disable all transmitted alarms.

rai Specifies sending a rem ote alarm indication (RAI) in response t o a loss of

DSX-1 interface.

Configures the line coding for bipol a r eight zero substitution (B8ZS).

Configures the FDL for ANSI T1.403 standard.

Specifies extended superframe (ESF) format.

than 655 feet. Choices are -22.5, -15, -7.5, and 0 dB. 655 feet. Range is 0 to 655 feet.

interface.

(metallic) loopback of the signal received by the remote unit from the network. (T1 interface only.)

(metallic) loopback of the signal received from the network.

frame. Also prevents a received RAI from causing a change in interfac e operational status.

For more detailed documentation, visit us online at www.adtran.com.

remote-loopback

Configures the interface to respond to loopbacks initiated by a remote unit (or service provider). Use the no form of this command to disable this feature.

signaling-mode [message-oriented | none | robbed-bit*]

Configures the signaling type (robbed-bit for voice or clear channe l for data) for the DS0s mapped to the DSX-1 port.

message-oriented Specifies clear channe l signaling on Channel 24 only. Use this signaling none Specifies clear channel signaling on all 24 DS0s. Use this signaling type robbed-bit* Specifies robbed bit signaling on all DS0s. Use this signaling type for voice-

snmp trap line-status

Controls the Simple Network Management Protocol (SNMP) variable dsx1LineStatusChangeTrapEnable (RFC2495) to enable (or disable) the interface to send SNMP traps when there is an interface status change. Use the no form of this command to disable this trap.

snmp trap link-status

Controls the Simple Network Management Protocol (SNMP) variable i fLinkUpDownTrapEnable (RFC2863) to enable (or disable) the interface to send SNMP traps when there is an interface status change. Use the no form of this command to disable this trap.

snmp trap threshold-reached

Controls the Simple Network Management Protocol (SNMP) variable adGenAOSDs1ThresholdReached (adGenAOSDs1-Ext MIB) to enable the interface to send SNMP traps when a DS1 performance counter threshold is reached. Use the no form of this command to disable this trap.

tdm-group <group number> timeslots <1-24> speed 64 Creates a group of contiguous DS0s on this interface to be used during the cross-connect process. <group number> Identifies the created TDM group (valid range: 1 to 255).

timeslots <1-24> Specifies the DS0s to be used in the TDM group. This can be entered as a

speed 64 Specifies the individual DS0 rate on the T1 interface to be 64kbps. This is

Activates the built-in pattern generator and begin sending the specified test pattern. Can be used to verify a data path when used in conjunction with an active loopback. Use the no form of this command to cease pattern generation.

clear Clears the test pattern error count. errors Displays the test pattern error count. insert Inserts an error into the currently active test pattern. ones Generates a test pattern of continuous ones. p215 Generates a pseudorandom test pattern sequence based on a 15-bit shift

p220 Generates a pseudorandom test pattern sequence based on a 20-bit shift p511 Generates a test pattern of repeating ones and zeros.

qrss Generates a test pattern of random ones and zeros. zeros Generates a test pattern of continuous zeros.

* Indicates default values.

type with QSIG installations. with data-only or PRI DSX-1 installations. only DSX-1 applications.

single number representing one of the 24 T1 channel timeslots or as a contiguous group of DS0s. (For example, 1-10 specifies the first 10 channels of the T1.)

the only supported speed on this module.

Important: For additional details on product features, specifications, installation, and safety, refer to the appropriate Hardware Installation Guide on the ADTRAN OS System Documentation CD shipped with the base unit and available online at www .adtran.com.