Acer X223W User Manual

Safety Instructions

Observe the folowing safety guidelines when connection and using your monitor:

Be sure that your monitor is electrically rated to operate with the AC power available in your location.
Locate your monitor near an easily accessible electrical outlet.
Place the monitor on a solid surface and treat it carefully. The screen can be damaged if dropped, sharply hit, or touched
with a sharp or abrasive implement.
Put your monitor in a location with low humidity and a minimum of dust.
Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the power cable, and keep
the cable away from where people could trip over it.
Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock.
To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor's case.
Be sure to hold the plug, not the cable, when disconnecting the monitor from an electrical outlet.
Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be
blocked or covered. Also, avoid using the monitor on a bed, sofa, rug, or other soft surface.
Doing so may block the ventilation openings in the bottom of the cabinet. If you put the monitor in a bookcase or some
other enclosed space, be sure to provide adequate ventilation.
Do not expose the monitor to rain or use it near water. If the monitor accidentally gets wet, unplug it and contact an
authorized dealer immediately. You can clean the exterior of the monitor with a damp cloth when necessary, but be sure
to unplug the monitor first. If your monitor does not operate normally-in particular, if there are any unusual sounds or smells

coming from it -unplug the monitor immediately and contact an authorized dealer or service center.

Connecting Your Monitor to a Computer

1 .Connect Video Cable

a. Make sure both the monitor and computer are powered-OFF.
b. Connect the video cable to the computer.
c. (only Dual-Input Model) Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other

end to the computer's port.

2. Connect power cord
Connect the power cord to the monitor, then to a properly grounded AC outlet.

3. Connect the Audio Cable.(optional)

4. Power-ON Monitor and Computer
Power-ON the monitor first, then power-ON the computer.

This sequence is very important.

5. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem.

Troubleshooting Tips

No Power - The monitor's power indicator is off.

Make sure the monitor power cable is fully inserted in the monitor's power port and the electrical outlet.
Test the electrical ou let by plugging in a working electrical device such asa lamp.

Try another power cable on the monitor. You can use the computer's power cable to perform this test.

No Video - The monitor's power indicator is on but theere are no
image on the screen.

Ensure that the video connector is properly connected to the computer.
Ensure that the computer is on and functioning properly.

Turn off the monitor and check the video cable pins. Make sureño pins are bent.

Operationg Detail

Please refer to user's guide in CD-ROM packaged with this monitor

LCD Monitor Quick Setup Guide

Regulations and safety notices

FCC notice

This device has been tested and found to comply with the limits for a Class Bdigitai
device pursuant to Part 15 of the PCCrules These limits are designed to provide reason
able protection against harmful Interference In a residential Installation. This device
generates, uses, and can radiate radie frequency energy and, if not installed and used In
accordance with the instructions, may cause harmful interference to radio communica
tions.
However, there is no guarantee that Interference will not occur In a particular installa
tion . If this device does cause harmful Interference to radio or television reception, which
can be determined by turning the device off and on, the user is encouraged to try to
correct the Interference by one or more of the foil owl ng measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.
« Connect the device into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

CE declaration of Conformity

Hereby, Acer Inc., declares that this LCD monitor is in compliance with the essential requirements
and requirements and other relevant provisions of EMC Directive 89/336/EEC, amended by
92/31/EEC and 93/68/EEC, Low Voltage Directive 2006/9S/EC, and RoHS Directive 2002/95/EC

Notice: Shielded cables

All connections to other computing devices must be made using shielded cables to

maintain compliance with EMC regulations.

Notice: Peripheral devices

Only peripherals (input/output devices, terminals, printers,etc.) certified to comply with
the CleissB limits may be attached to this equipment. Operation with non-certifled
peripheralsIsllkely to result In Interference to radio and TVreception.

Caution

Changes or modifications not expressly approved by the manufacturer could void the
user authority, which is granted by the Federal Communications Commission ,to operate
this product.

Operation conditions

This device complies with Part 15 of the FCC RiJea Operation is subject to the following
two condit lons:(1) this device may not cause harmful interference, and (2) this device
must accept any interference received. Including interference that may cause undesiad
operation.

Notice: Canadian users

This Class B digital apparatus comp lies with Canadian ICES-003.

Remarque à l’intention des utilisateurs canadiens

Cet appareil numérique de la classeB est conforme a la norme NMB-003 du Canada.

LAMP Disposal

LAMP(S) INSIDE THIS PRO DUCT CONTAIN MERCURY AND MUST BE RECYCLED
OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR
MORE INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT
WWW .EIAE.ORC. FOR LAMP SPECIFIC DISPOSAL INFORMATION CHECK
WWW.LAMPRECYCLE.ORC.

Disposal of Waste Equipment by Users in Private Household in

the European Union

This symbol on the product or on Its packaging Indicates that this product must

not be disposed of with your other household waste. Instead, it is your respon
sibility to dispose of your waste equipment by handing it over to a designated
collection point for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment at the time of
disposal will help to conserve natural resources and ensure that it Is recycled in
a manner that protects human health and the environment. For more Informa
tion about where you can drop off your waste equipment for recycling, please
contact your local city office, your household waste disposal service or the shop
where you purchased the produa.

Regulatory Compliance

H F© C€ B ■®"S

iioM ^ ®

R43348 ME61 N214 Dlaposa Property

Lam|)(8) Contain Mercury.

LCD Monitor Quick Setup Guide

■E.
E253847
26JX

_________