3M FT-32 User Manual
FT-32, Denatonium Benzoate Fit Test Solution 04/11/16
__________________________________________________________________________________________
Page 1 of 8
Safety Data Sheet
Copyright,2016,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
Document Group:
07-6218-7
Version Number:
15.00
Issue Date:
04/11/16
Supercedes Date:
04/22/14
SECTION 1: Identification
1.1. Product identifier
FT-32, Denatonium Benzoate Fit Test Solution
Product Identification Numbers
70-0707-0966-5
1.2. Recommended use and restrictions on use
Recommended use
Fit Test Solution.
1.3. Supplier’s details
MANUFACTURER:
3M
DIVISION:
Personal Safety Division
ADDRESS:
3M Center, St. Paul, MN 55144-1000, USA
Telephone:
1-888-3M HELPS (1-888-364-3577)
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
2.1. Hazard classification
Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.
2.2. Label elements
Signal word
Not applicable.
Symbols
Not applicable.
Pictograms
Not applicable.
2.3. Hazards not otherwise classified
None.
FT-32, Denatonium Benzoate Fit Test Solution 04/11/16
__________________________________________________________________________________________
Page 2 of 8
SECTION 3: Composition/information on ingredients
Ingredient C.A.S. No. % by Wt
WATER 7732-18-5 90 - 100
SODIUM CHLORIDE 7647-14-5 3 - 10
DENATONIUM BENZOATE 3734-33-6 0 - 1
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
Remove person to fresh air. If you feel unwell, get medical attention.
Skin Contact:
No need for first aid is anticipated.
Eye Contact:
No need for first aid is anticipated.
If Swallowed:
No need for first aid is anticipated.
4.2. Most important symptoms and effects, both acute and delayed
See Section 11.1. Information on toxicological effects.
4.3. Indication of any immediate medical attention and special treatment required
Not applicable
SECTION 5: Fire-fighting measures
5.1. Suitable extinguishing media
Non-combustible. Use a fire fighting agent suitable for surrounding fire.
5.2. Special hazards arising from the substance or mixture
None inherent in this product.
5.3. Special protective actions for fire-fighters
No special protective actions for fire-fighters are anticipated.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Observe precautions from other sections.
6.2. Environmental precautions
Avoid release to the environment.
6.3. Methods and material for containment and cleaning up
Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially
available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent
material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible.
Place in a closed container approved for transportation by appropriate authorities. Clean up residue with water. Seal the
FT-32, Denatonium Benzoate Fit Test Solution 04/11/16
__________________________________________________________________________________________
Page 3 of 8
container. Dispose of collected material as soon as possible.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
For industrial or professional use only. Do not eat, drink or smoke when using this product.
7.2. Conditions for safe storage including any incompatibilities
No special storage requirements.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Occupational exposure limits
No occupational exposure limit values exist for any of the components listed in Section 3 of this SDS.
8.2. Exposure controls
8.2.1. Engineering controls
No engineering controls required.
8.2.2. Personal protective equipment (PPE)
Eye/face protection
None required.
Skin/hand protection
No protective gloves required.
Respiratory protection
None required.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
General Physical Form:
Liquid
Odor, Color, Grade:
Clear, odorless solution with a bitter taste. Freezing point = -4
degrees Centigrade.
Odor threshold
No Data Available
pH
Approximately 6.52
Melting point
Not Applicable
Boiling Point
>=212 ºF
Flash Point
No flash point
Evaporation rate
Not Applicable
Flammability (solid, gas)
Not Applicable
Flammable Limits(LEL)
Not Applicable
Flammable Limits(UEL)
Not Applicable
Vapor Pressure
18 mmHg [@ 20 ºC]
Vapor Density
Not Applicable
Density
1.034 g/ml
Specific Gravity
1.034 [Ref Std: WATER=1]
Solubility in Water
Complete
Loading...