Cannon FITZROY PROFILE INBUILT User Manual

Size:
878.36 Kb
Download

MAKER’S WARRANTY

INBUILT MODELS

FITZPIB, FITZPIBLP

USER INSTRUCTIONS

INSTALLATION INSTRUCTIONS

SERVICE INSTRUCTIONS

Cannon

FITZROY PROFILE

This heater is approved for use with Natural and Propane gases. Please leave instructions with the owner

Contents

Contents

2

Warranty

3

 

 

Safety warnings

4-5

 

 

What to do if you smell gas

Warnings

Standards

User instructions

6-8

Operating instructions

Cleaning

Heater specifications

9

Installation instructions

10-14

 

 

Clearances

Fitment of cabinet depth spacer

Installation into a masonry fire place

Sealing

Gas connection

15-16

Fuel bed & log installation

 

Gas control

17-18

 

 

Gas pressure point

 

Gas pressure adjustment

 

Service instructions

19

 

 

General

To replace the gas control

To replace the fan

To replace the electronic controller

To remove the burner and electrodes

To check pressures

Trouble shooting

19-22

Connections

Electrical wiring diagram

Authorised service agents

22

2

Warranty

The Cannon appliance is warranted against defects in materials and workmanship for a period of one, (1) year from its date of original purchase, for residential use in Australia.

Warranty service, which includes parts and labour for the replacement or repair of defective parts, is available through Cannon Authorised Service Agencies. (Please refer to the list of authorised service agents in this manual.)

Consumers are responsible for service person’s travel outside normal service areas (approximately seventy (70k) radius from the nearest Cannon dealer’s location), local cartage, and normal maintenance as described in this manual.

Any product subjected to misuse, abuse, negligence, accident or alteration will have its warranty voided. The defacement of serial plate will have its warranty voided.

If installation is not carried out in accordance with manufacturer’s instructions, this warranty may be void.

The customer must keep their “Tax Invoice” as proof of purchase of this product and compliance certificate as proof of required installation.

Model number: ______________________________________

Serial number: _______________________________________

Date of manufacture: _________________________________

Date installed: _______________________________________

Compliance Certificate No: ____________________________

Designed, manufactured and distributed by:

Sampford and Staff Pty Ltd. 421 Smith Street

Fitzroy, Vic, 3065 Tel: (03) 9418 5888

Don’t risk your appliance warranty

Only a licensed person will give you a Compliance Certificate, showing that the work complies with all the relevant standards.

And only a licensed person will have insurance protecting their workmanship for 6 years.

So make sure you use a licensed person to install this appliance and ask for your Compliance Certificate to ensure the manufacturers appliance warranty will be honoured.

3

Safety Warnings

What to do if you smell gas

Warnings

Please read this manual before installing and using the heater.

1.Turn OFF the main gas supply.

2.Extinguish any open flame.

3.Open windows.

4.Do not touch electrical switches.

5.Do not use your telephone.

6.Call your gas supplier immediately from a neighbour’s phone.

1.Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to other sections of this manual for correct procedures, or consult with place of purchase, a licensed plumber, a gas supplier or service agent listed in this manual.

2.Due to high temperatures the room heater should be located out of traffic and away from:

Furniture and draperies,

Combustible materials,

Gasoline and other flammable liquids,

Do not place clothing or other flammable material on or near the heater.

3.Keep curtains*, clothing, furniture and other flammable materials at least 900mm from front and sides of the heater.

*At the owner’s discretion curtain clearance can be less than 900mm as long as they are restrained from the front, top and sides of the heater. The manufacturer takes no responsibility if curtain clearance is less than 900mm and not restrained.

4.Children and adults should be alerted to the hazard of high surface temperature and should take care to avoid burns or clothing ignition.

This heater is not intended for use by young children or infirm persons without supervision.

Young children should be carefully supervised when they are in the same room as the heater.

Young children should be supervised to ensure that they do not play with the heater.

5.Never attempt to burn paper or any other material in the heater.

6.Do not spray aerosols in the vicinity of this appliance while it is in operation.

Do not place articles against, or store flammable materials near this appliance

4

Standards

7.If removed the glass window must be put back onto the unit prior to operating the heater.

8.Installation and repairs should be performed by a licensed service person only, refer to back of brochure for service number.

9.For installation into a non-combustiblefireplace, i.e.: masonry or brick or into a mock fireplace, i.e. timber or plasterboard, the chimney and base should be of sound construction and be free from cracks and holes (to ensure that sufficient flue draught can be generated).

NOTE: WHEN INSTALLING INTO A MOCK FIREPLACE A MOCK FIREPLACE INSTALLATION KIT MUST BE USED.

10.The heater must be properly installed in a working chimney or connected to a venting system. Operation of this heater, when not connected into a working chimney or a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death.

11.The appliance should be inspected prior to use, with regular inspections (annually) to be made by a licensed service person. It is important that circulating air passageways of the appliance be kept clean, dirt and lint free, for a safe and efficient operation of the heater.

12.On first lighting your heater a smell may occur due to it’s new condition. This is quite normal and will disappear after a few hours use at the maximum control position.

Important:

WHEN THIS HEATER IS OPERATING, THE MESH GUARD IS HOT.

The mesh safety guard fitted to the heater conforms to AGA requirements.

For heaters fitted with the optional glass front it should be noted that THE GLASS FRONT IS HOT.

For permanent protection of young children or the infirm a secondary guard should be placed around the heater. A secondary guard is not provided with this heater and may be purchased by the owner.

This appliance meets the following standards:

Standards Australia: AS 3100

AS 5601/AG 601

AS 4553/AG 103

5

User instructions

Operating instructions

1.Plug the power cord into the wall socket and turn on the power to the heater, see figure 1. Refrain from using an extension cord.

1

2. For control layout refer to figure 2

2

3. To turn heater on press switch to POWER ON position. There is a 5 second delay before the burner ignites. At this setting the burner is on LOW and the fan speed is on LOW. Refer figure 3.

The burner will ignite on both HIGH and LOW settings.

3

4. To turn burner to HIGH setting, press switch for HIGH setting. Refer figure 4.

4

6

5. To increase the fan speed to MED, press switch for MED setting. Refer figure 5.

5

6. To increase the fan speed to HIGH, press switch for HIGH setting. Refer figure 6.

6

7. To turn the burner to LOW setting, press switch for LOW setting. Refer figure 7.

On low burner setting it is more efficient to operate the fan speed on LOW.

8. If the burner fails to ignite, wait 20 seconds and repeat the ignition procedure. See below.

To turn burner OFF

To turn burner ON

7

User instructions continued

Cleaning.

All cleaning should be carried out when the heater is cold. Nor-

 

mally the heater should only need wiping with a lint - free damp

 

cloth. Any stubborn stains can be removed with a non-abrasive

 

spray on cleaner. If an abrasive cleaner is used the paint finish will

 

be damaged.

 

Internally the heater should only be cleaned by a licensed service

 

person listed in this manual.

 

If your heater requires attention contact your supplier or licensed

 

service person listed in this manual.

 

Important:

 

The appliance should be inspected before use and at least annu-

 

ally by an authorised service person. More frequent cleaning may

 

be required due to excessive lint build-upfrom carpeting, bedding

 

materials, pet hair, etc.

 

It is imperative that control compartments, burners and circulating

 

air passage ways of the appliance be kept clean.

 

Do not use this fire if the glass is cracked or with the glass safety

 

screen removed.

8

Heater Specifications

Do not use fire with broken or missing logs.

Gas type:

Natural or Propane gas, as indicated

 

on data label

Gas consumption:

26 MJ/hr input

Energy star rating:

3.77

 

Energy output:

20.7 MJ/hr

Heater type:

Heater approved to

 

AS 4553/AG103.

Operating pressure:

Natural gas: 1.0 kPa

 

Propane gas: 2.65 kPa

Gas regulator:

Integral with controller (NG)

Min. inlet pressure:

1.13 kPa (NG)

 

Propane gas: Regulated to supply 2.7

 

 

kPa to appliance

Fan:

Three speed

Controller:

Electronic

Minimum cavity

Height: 605mm dimensions*

dimensions

Width:

700mm

 

Depth:

393mm

Power requirement:

240 VAC 10 A

Optional Accessories:

• Glass front

 

• Gold or silver trim

 

• Mock fireplace installation kit*

 

• Cabinet depth spacer

 

• Heater surround

Overall dimensions:

Refer fig. 8

*Note: when installing into a mock fireplace a mock fireplace installation kit must be used.

8

9

Installation instructions

Clearances

1.This appliance is to be installed by a licensed service person only.

2.This appliance is to be installed in accordance with the manufacturer’s installation instructions, AS 5601/AG601, Municipal Building Codes, Electrical Wiring Regulations and any other statutory regulations.

3.Remove the heater from the carton and remove the three transit screws.

Check that the heater is suitable for gas available.

(Please dispose of packaging appropriately, keep away from children).

4.Ensure the minimum clearances to combustible construction are maintained during installation, including adequate space for the proper operation and servicing of the heater. For clearances to furniture and curtains refer to warning on page 4.

For minimum clearances refer figures 9 and 10.

Note: Ensure that the combustion air opening under the heater is not obstructed.

Fitment of cabinet depth spacer

9

10

A CLEARANCE OF 50mm MUST BE MAINTAINED BETWEEN THE REAR OF THE CABINET AND THE REAR WALL OF THE FIRE PLACE.

The clearance is required for correct fluing of the appliance. If the clearance is less than 50mm a cabinet depth spacer must be fitted. The spacer can be ordered from the relevant service agent. Order specification for the spacer is ‘Fitzspacer”. To fit the spacer follow the procedure described below.

a.Remove lower panel and front panel of heater as indicated in figure 16 & 17.

b.Open the packaging and remove the three sections which make up the spacer assembly. Refer figure 11.

10