ZyXEL Communications GS-1124A, GS-1116A User Manual

Dimension

GS-1116A and GS-1124A

Unmanaged 16 or 24 Port Gigabit Switch with 2 mini-GBIC Ports

User’s Guide

Version 1

9/2006

Edition 2

Dimension GS-1116A/GS-1124A Gigabit Switch

Copyright

Copyright © 2006 by ZyXEL Communications Corporation

The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored
in a retrieval system, translated into any language, or transmitted in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the
prior written permission of ZyXEL Communications Corporation.

Published by ZyXEL Communications Corporation. All rights reserved.

Disclaimer

ZyXEL does not assume any liability arising out of the application or use of any products, or software
described herein. Neither does it convey any license under its patent rights nor the patents rights of
others. ZyXEL further reserves the right to make changes in any products described herein without
notice. This publication is subject to change without notice.

Trademarks

Trademarks mentioned in this publication are used for identification purposes only and may be
properties of their respective owners.

ii Copyright

Dimension GS-1116A/GS-1124A Gigabit Switch

ZyXEL Limited Warranty

ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in
materials or workmanship for a period of up to two (2) years from the date of purchase. During the
warranty period and upon proof of purchase, should the product have indications of failure due to
faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective
products or components without charge for either parts or labor and to whatever extent it shall deem
necessary to restore the product or components to proper operating condition. Any replacement will
consist of a new or re-manufactured functionally equivalent product of equal value, and will be solely
at the discretion of ZyXEL. This warranty shall not apply if the product is modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working conditions.

Note

Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This
warranty is in lieu of all other warranties, express or implied, including any implied warranty of
merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for
indirect or consequential damages of any kind of character to the purchaser.

To obtain the services of this warranty, contact ZyXEL's Service Center for your Return Material
Authorization number (RMA). Products must be returned Postage Prepaid. It is recommended that the
unit be insured when shipped. Any returned products without proof of purchase or those with an out­dated warranty will be repaired or replaced (at the discretion of ZyXEL) and the customer will be
billed for parts and labor. All repaired or replaced products will be shipped by ZyXEL to the
corresponding return address, Postage Paid. This warranty gives you specific legal rights, and you
may also have other rights that vary from country to country.

ZyXEL Limited Warranty iii

Dimension GS-1116A/GS-1124A Gigabit Switch

Interference Statements and Warnings

FCC Interference Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause
undesired operations.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.

CE Mark Warning

This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

Taiwanese BCIQ A Warning

Certifications

1. Go to www.zyxel.com

2. Select your product from the drop-down list box on the ZyXEL home page to go to that product's

page.

Select the certification you wish to view from this page.

iv Interference Statements and Warnings

Dimension GS-1116A/GS-1124A Gigabit Switch

Customer Support

If you have questions about your ZyXEL product or desire assistance, contact ZyXEL
Communications Corporation offices worldwide, in one of the following ways:

Contacting Customer Support

When you contact your customer support representative, have the following information ready:

• Product model and serial number

• Warranty information

• Date that you received your product.

• Brief description of the problem and the steps you took to solve it.

LOCATION

CORPORATE
HEADQUARTERS
(WORLDWIDE)

COSTA RICA

CZECH REPUBLIC

DENMARK

FINLAND

GERMANY

HUNGARY

KAZAKHSTAN

NORTH AMERICA

SUPPORT E-MAIL

SALES E-MAIL

[e-mail]

[e-mail] [phone] ftp.zyxel.com

[e-mail]

[e-mail] [phone] ftp.zyxel.co.cr

[e-mail]

[e-mail] [phone]

[e-mail]

[e-mail] [phone]

[e-mail]

[e-mail] [phone]

[e-mail]

[e-mail]

[e-mail] [phone]

[e-mail]

[e-mail] [phone]

http://zyxel.kz/support

[e-mail] [phone]

[e-mail]

[e-mail] [phone] ftp.us.zyxel.com

TELEPHONE

FAX FTP SITE

[phone] www.zyxel.com

[phone] www.zyxel.co.cr

[phone]

[phone]

[phone]

[phone] FRANCE

[phone]

[phone]

[phone]

[phone]

1-800-255-4101
[phone]

WEB SITE METHOD

www.europe.zyxel.com

ftp.europe.zyxel.com

www.zyxel.cz ZyXEL Communications

www.zyxel.dk ZyXEL Communications A/S

www.zyxel.fi ZyXEL Communications Oy

www.zyxel.fr ZyXEL France

www.zyxel.de ZyXEL Deutschland GmbH.

www.zyxel.hu ZyXEL Hungary

www.zyxel.kz ZyXEL Kazakhstan

www.us.zyxel.com

REGULAR MAIL

ZyXEL Communications
Corp.

6 Innovation Road II Science
Park Hsinchu 300 Taiwan

ZyXEL Costa Rica
Plaza Roble Escazú Etapa El

Patio, Tercer Piso San José,
Costa Rica

Czech s.r.o.
Modranská 621 143 01 Praha

4 - Modrany Ceská Republika

Columbusvej 2860 Soeborg
Denmark

Malminkaari 10 00700
Helsinki Finland

1 rue des Vergers Bat. 1 / C
69760 Limonest France

Adenauerstr. 20/A2 D-52146
Wuerselen Germany

48, Zoldlomb Str. H-1025,
Budapest Hungary

43, Dostyk ave.,Office 414
Dostyk Business Centre
050010, Almaty Republic of
Kazakhstan

ZyXEL Communications Inc.
1130 N. Miller St. Anaheim
CA 92806-2001 U.S.A.

Customer Support v

Dimension GS-1116A/GS-1124A Gigabit Switch

NORWAY

RUSSIA

SPAIN

SWEDEN

UKRAINE

UNITED KINGDOM

[e-mail]

[e-mail] [phone]

[e-mail]

http://zyxel.ru/support

[e-mail] [phone]

[e-mail]

[e-mail] [phone]

[e-mail]

[e-mail] [phone]

[e-mail]
m

[e-mail] [phone]

[e-mail]

[e-mail] [phone] ftp.zyxel.co.uk

[phone]

[phone] POLAND

[phone]

[phone]

[phone]

[phone]

[phone]

[phone]
08707 555779 (UK only)

www.zyxel.no ZyXEL Communications A/S

www.pl.zyxel.com ZyXEL Communications ul.

www.zyxel.ru ZyXEL Russia

www.zyxel.es ZyXEL Communications Arte,

www.zyxel.se ZyXEL Communications A/S

www.ua.zyxel.com ZyXEL Ukraine

www.zyxel.co.uk

Nils Hansens vei 13 0667
Oslo Norway

Okrzei 1A 03-715 Warszawa
Poland

Ostrovityanova 37a Str.
Moscow, 117279 Russia

21 5ª planta 28033 Madrid
Spain

Sjöporten 4, 41764 Göteborg
Sweden

13, Pimonenko Str. Kiev,
04050 Ukraine

ZyXEL Communications UK
Ltd.,11 The Courtyard,
Eastern Road, Bracknell,
Berkshire, RG12 2XB, United
Kingdom (UK)

vi Customer Support

Dimension GS-1116A/GS-1124A Gigabit Switch

Table of Contents

Chapter 1 Getting to Know the Switch.................................................................................................1-1

1.1 Introduction ........................................................................................................................................ 1-1

1.2 Features .............................................................................................................................................. 1-2

1.3 Package Contents ............................................................................................................................... 1-3

1.4 Gigabit Switch Network Applications................................................................................................ 1-3

Chapter 2 Hardware Description and Installation.................................................................................2-1

2.1 Desktop Installation............................................................................................................................ 2-1

2.2 Rack-mounted Installation.................................................................................................................. 2-2

2.3 Rear Panel .......................................................................................................................................... 2-3

2.4 Front Panel ......................................................................................................................................... 2-3

Chapter 3 Troubleshooting ...................................................................................................................3-1

3.1 Introduction ........................................................................................................................................ 3-1

3.2 Improper Network Cabling and Topology ......................................................................................... 3-2

Table of Contents vii

Dimension GS-1116A/GS-1124A Gigabit Switch

List of Figures

Figure 1-1 GS-1116A ...........................................................................................................................1-1

Figure 1-2 GS-1124A ...........................................................................................................................1-1

Figure 1-3 Gigabit Switch for Server Farm ..........................................................................................1-4

Figure 1-4 Gigabit Switch for Super User Work Groups .....................................................................1-5

Figure 2-1 Attaching Rubber Feet ........................................................................................................2-1

Figure 2-2 Attaching Mounting Brackets and Screws..........................................................................2-2

Figure 2-3 Switch Mounting to an EIA Standard 19-inch Rack...........................................................2-2

Figure 2-4 Switch Rear Panel ...............................................................................................................2-3

Figure 2-5 GS-1116A Front Panel........................................................................................................2-3

Figure 2-6 GS-1124A Front Panel........................................................................................................2-3

Figure 2-7 Transceiver Installation Procedure......................................................................................2-5

Figure

Figure 2-11 GS-1116A Front Panel LEDs ...........................................................................................2-7

Figure 2-12 GS-1124A Front Panel LEDs ...........................................................................................2-7

2-8 Transceiver Removal Example ...........................................................................................2-6

List of Tables

2-1 GS-1116A/GS-1124A: Front Panel Ports ............................................................................2-3

Table

Table 2-2 Network Cable Types...........................................................................................................2-7

Table 2-3 Front Panel LED Descriptions .............................................................................................2-7

Table 3-1 Troubleshooting PWR LED .................................................................................................3-1

Table 3-2 Troubleshooting LNK/ACT LED ........................................................................................3-1

Table 3-3 Troubleshooting 1000 LEDs ................................................................................................3-1

Table 3-4 Troubleshooting Improper Network Cabling and Topology................................................3-2

List of Figures/Tables ix

Dimension GS-1116A/GS-1124A Gigabit Switch

Preface

Congratulations on your purchase of the Dimension GS-1116A or GS-1124A unmanaged 16 or 24
port Gigabit switch with 2 mini-GBIC ports.

This preface introduces you to the Dimension GS-1116A and GS-1124A and discusses the
organization and conventions of this User’s Guide. It also provides information on other related
documentation.

About Gigabit Ethernet

Gigabit Ethernet is a 1Gbps (1000Mbps) extension of the IEEE 802.3 Ethernet networking standard.
Its primary applications are in corporate LANs, campus networks and service provider networks where
it can be used to tie together existing 100Mbps Ethernet networks.

About the Dimension GS-1116A and GS-1124A Gigabit Switch

The GS-1116A or GS-1124A is designed to improve your network performance with high-speed data
transmission over copper wire. The GS-1116A or GS-1124A provides an ideal upgrade path for
existing Ethernet-based networks that need more bandwidth. It can be installed as a backbone network
while retaining existing investments in Ethernet hubs, switches and wiring infrastructure.

General Syntax Conventions

For brevity’s sake, we will use “e.g.” as shorthand for “for instance”, and “i.e.” as shorthand for “that
is” or “in other words” throughout this manual.

The Dimension GS-1116A or GS-1124A unmanaged 16 or 24 port gigabit switch with 2 mini-GBIC
Ports may be referred to as “the switch” in this manual except where we refer to a specific switch.

Related Documentation

ZyXEL Web Site

The ZyXEL download library at www.zyxel.com contains additional support documentation and an
online glossary of networking terms.

x Preface

Dimension GS-1116A/GS-1124A Gigabit Switch

Chapter 1

Getting to Know the Switch

This chapter describes the key features, benefits and applications of the switch.

1.1 Introduction

The switch is designed for the campus or building environment as a high bandwidth backbone. The
GS-1116A has 16 100/1000 Mbps RJ-45 ports. The GS-1124A has twenty-four 100/1000 Mbps RJ-45
ports. You can connect the switch to existing Ethernet routers, switches or hubs without additional
expensive wiring or equipment installation.

Figure 1-1 GS-1116A

Figure 1-2 GS-1124A

Gigabit Ethernet over copper technology is a cost effective way of upgrading network equipment
from fast Ethernet to Gigabit speed by using standard 4-pair Category 5 copper cabling. The Mini
GBIC slots allow for fiber optic high-speed backbone connections.

Both ports 15 and 16 in the GS-1116A (or 23 and 24 in the GS-1124A) support 3.3V Mini GBIC.
The GBIC port auto detects between Giga copper and Mini GBIC. The Mini GBIC module is
optional. When the Mini GBIC module is not installed, these act as Giga copper connections.

Getting to Know the GS1116A/GS-1124A 1-1

Dimension GS-1116A/GS-1124A Gigabit Switch

The switch is an ideal solution for solving traffic block at the core of the network. It offers auto­negotiation 100/1000Base-T Gigabit Ethernet ports that can significantly improve your network
backbone performance.

1.2 Features

• Conforms to IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3z Gigabit fiber and

IEEE 802.3ab 1000Base-T standards.

• IEEE 802.1p supports two priority queues for outgoing traffic helping improving network

efficiency and performance.

• Auto-negotiating 100/1000Mbps Ethernet RJ-45 ports.

• Automatic MDI/MDIX supported.

• Switching fabric of 32Gbps in the GS-1116A and 48Gbps in the GS-1124A.

• N-way Auto-negotiation supported.

• Embedded 8K MAC address table providing 8000 MAC address entries.

• Two 3.3V Mini GBIC ports for Gigabit fiber transceiver.

• Two Gigabit copper ports.

• Supports auto address learning.

• Supports store-and-forwarding switching architecture for abnormal packet filtering.

• Back-Pressure-Base flow control on Half-duplex mode Ethernet ports.

• Pause-Frame-Base flow control on Full-duplex mode Ethernet ports.

• No-Blocking full wire speed architecture.

• One fan for good ventilation and to increase system heat sink performance.

• Power, 1000 and LNK/ACT LEDs.

• Standard 19-inch rack mount design

1.2.1 IEEE 802.1p Class of Service

The IEEE 802.1p Class of Service (CoS) provides two queues for high and low priority traffic. This
improves network efficiency and performance by giving higher priority to outgoing traffic. The lower
queue has a priority value in the range of zero to three and the higher queue has a priority value in the
range of four to seven.

) When the Mini GBIC module is installed, the Mini GBIC (Giga fiber) port

has higher priority than Giga copper port. When the Mini GBIC port is
connected, the Giga copper port is disabled.

1-2 Getting to Know the GS1116A/GS-1124A

Dimension GS-1116A/GS-1124A Gigabit Switch

1.3 Package Contents

Compare the contents of your GS-1116A/GS-1124A Gigabit Switch package with the checklist
below. If any item is missing or damaged, please contact your local dealer.

• GS-1116A or GS-1124A Gigabit switch

• Power cord

• Quick Start Guide

• This User’s Guide in CD-ROM format.

• Four rubber feet

• Rack mount brackets

1.4 Gigabit Switch Network Applications

This section provides a sample of network topologies in which the Gigabit switch functions as a high­bandwidth backbone switch for a server farm or as a high-bandwidth backbone switch for a super user
workgroup. The switch is an ideal upgrade for 100Mbps Ethernet networks. You can connect existing
switches, hubs or computers with Gigabit 1000Base-T Ethernet adapters to the switch.

1.4.1 Gigabit Switch for Server Farm

The following figure depicts the GS-1124A (Z) connected to a computer network (via switches A, B
and C) and a server farm (via Gigabit switch G). For enterprise networks where large data broadcasts
are constantly processed, this switch is suitable for connecting departmental switches to the core
Gigabit switch through a number of servers. Connecting servers to the core Gigabit switch allows
each end station to rapidly access the server’s data and to smoothly communicate with all the devices
in the network.

Getting to Know the GS1116A/GS-1124A 1-3

Dimension GS-1116A/GS-1124A Gigabit Switch

Figure 1-3 Gigabit Switch for Server Farm

1.4.2 Gigabit Switch for “Super User” Work Groups

You can use the GS-1116A or the GS-1124A to connect servers, switches, workstations and
computers (the Gigabit 1000Base-T NIC must be installed onto the computer) to each other.

The following figure depicts a typical backbone application of the switch in an enterprise
environment. The “Normal User” workgroup (A, B, C) is connected to a switch via a 10/100Mbps
and the “Super User” workgroup (D, E, F) is connected to a Gigabit switch (G). This enables the two
networks to communicate with each other, prioritizing the “Super User” network with higher
connection speeds though a Gigabit switch.

The “Normal User” workgroup runs applications that are not time sensitive and do not require large
amounts of bandwidth, such as Internet browsing and e-mail.

The “Super User” workgroup runs bandwidth-hungry applications like large FTP file transfers and
real time applications such as video conferencing.

The switch automatically learns node addresses, which are subsequently used to filter and forward all
traffic based on the destination address. You can use the Mini GBIC slots to connect with a fiber optic

1-4 Getting to Know the GS1116A/GS-1124A

Dimension GS-1116A/GS-1124A Gigabit Switch

network that extends your Ethernet network and to separate “Normal User” and “Super User”
networks.

Figure 1-4 Gigabit Switch for Super User Work Groups

Getting to Know the GS1116A/GS-1124A 1-5

Dimension GS-1116A/GS-1124A Gigabit Switch

Chapter 2

Hardware Description and Installation

This section discusses switch installations, hardware and functional overview.

The switch is suited to an office environment where it can be rack mounted on standard EIA racks or
placed as a standalone switch on a desktop.

) For proper ventilation, allow at least 4 inches (10 cm) of clearance at

the front, 3.4 inches (8 cm) at the back of the switch. This is especially
important for enclosed rack installations.

2.1 Desktop Installation

1. Set the switch upside-down on a study level space with a power outlet nearby.

2. Make sure there is enough clearance around the switch to allow air circulation and the attachment

of cables and the power cord.

3. Remove the adhesive backing from the supplied rubber feet.

4. Attach the rubber feet to each corner on the bottom of the switch. These rubber feet help protect

the switch from shock or vibration and ensure space between devices when stacking.

5. Turn the switch right side up after you attach the rubber feet.

Figure 2-1 Attaching Rubber Feet

) Do not block the ventilation holes. Leave space between switches

when stacking.

Hardware Description and Installation 2-1

Dimension GS-1116A/GS-1124A Gigabit Switch

2.2 Rack-mounted Installation

The switch can be mounted on an EIA standard size, 19-inch rack or in a wiring closet with other
equipment. Follow the steps below to mount your switch on a standard EIA rack using the included
rack-mounting kit.

1. Align one bracket with the holes on one side of the switch and secure it with the bracket screws.

Similarly, attach the other bracket.

Figure 2-2 Attaching Mounting Brackets and Screws

After attaching both mounting brackets, position the switch in the rack by lining up the holes in the

2.

brackets with the appropriate holes on the rack. Secure the switch to the rack with the rack’s
mounting screws.

Figure 2-3 Switch Mounting to an EIA Standard 19-inch Rack

2-2 Hardware Description and Installation

Dimension GS-1116A/GS-1124A Gigabit Switch

2.3 Rear Panel

The ventilation fan and three-pronged power receptacle are located on the rear panel of the switch.

Figure 2-4 Switch Rear Panel

2.3.1 Rear Panel Power Connection

Connect one end of the supplied power cord to the power receptacle on the back of the switch and the
other end to the 100-240 VAC, 50-60 Hz power source. Push the power switch to the ON position.

2.4 Front Panel

The following graphics show the front panels of the GS-1116A and the GS-1124A.

Figure 2-5 GS-1116A Front Panel

Figure 2-6 GS-1124A Front Panel

Table 2-1 GS-1116A/GS-1124A: Front Panel Ports

CONNECTOR DESCRIPTION

RJ-45 ports Connect these 100/1000 Mbps RJ-45 Ethernet ports to computers, hubs, Ethernet

switches or routers.

Mini GBIC ports Use mini GBIC transceivers in these ports for fiber-optical connections to

backbone Ethernet switches.

2.4.1 100/1000Mbps RJ-45 Auto-negotiating Ports

The GS-1116A has 16 100/1000 Mbps RJ-45 ports. The GS-1124A has twenty-four 100/1000 Mbps
RJ-45 ports. The auto-negotiation feature allows the switches to detect the speed of incoming
transmission and adjust appropriately without manual intervention. It allows data transfers of either

• 100Mbps in half-duplex mode

Hardware Description and Installation 2-3

Dimension GS-1116A/GS-1124A Gigabit Switch

• 100Mbps or 1000Mbps in full-duplex mode depending on your Ethernet network.

2.4.2 Auto-sensing (Auto MDI/MDIX) Ports

You can connect each RJ-45 auto-sensing port to a computer, hub or switch using either a straight
through or a crossover Ethernet cable.

2.4.3 Mini GBIC Slots

These are slots for Mini GBIC (Gigabit Interface Converter) transceivers. A transceiver is a single
unit that houses a transmitter and a receiver. The switch does not come with transceivers. You must
use transceivers that comply with the Small Form-factor Pluggable (SFP) Transceiver MultiSource
Agreement (MSA). See the SFF committee’s INF-8074i specification Rev 1.0 for details.

You can change transceivers while the switch is operating. You can use different transceivers to
connect to Ethernet switches with different types of fiber-optic connectors.

) To avoid possible eye injury, do not look into an operating fiber-optic

module’s connectors.

• Type: SFP connection interface

• Connection speed: 1 gigabit per second (Gbps)

Transceiver Installation

Use the following steps to install a mini GBIC transceiver (SFP module).

1.

Insert the transceiver into the slot with the exposed section of PCB board facing down.

2. Press the transceiver firmly until it clicks into place.

3. The switch automatically detects the installed transceiver. Check the LEDs to verify that it is

functioning properly.

2-4 Hardware Description and Installation

Dimension GS-1116A/GS-1124A Gigabit Switch

Figure 2-7 Transceiver Installation Procedure

Transceiver Removal

Use the following steps to remove a mini GBIC transceiver (SFP module) from the GBIC port.

1. Remove the fiber-optic cables from the transceiver.

2. Unlock the transceiver’s latch (latch styles vary).

3. Pull the transceiver out of the slot.

4. Put the transceiver’s dust cover on the transceiver.

Hardware Description and Installation 2-5

Dimension GS-1116A/GS-1124A Gigabit Switch

Figure 2-8 Transceiver Removal Example

) Keep the dust cover on a fiber optic module until you connect it.

Use the appropriate Ethernet or fiber-optic cables to connect the module to an Ethernet switch. With a
fiber-optic module, remove the dust covers from the connectors. You may need to clean the fiber­optic cable’s connectors with a cotton swab dipped in alcohol.

2.4.4 Front Panel Connections

You can use unshielded twisted pair (UTP) or shielded twisted-pair (STP) Ethernet cables for RJ-45
ports. The following table describes the types of network cable used for the different connection
speeds.

2-6 Hardware Description and Installation

Dimension GS-1116A/GS-1124A Gigabit Switch

Table 2-2 Network Cable Types

SPEED NETWORK CABLE TYPE

100Mbps

100Ω 2-pair UTP/STP Category 5

1000Mbps

100Ω 4-pair UTP/STP Category 5

) Make sure the cable length between connections does not exceed 100

meters (328 feet).

2.4.5 Front Panel LEDs

The LEDs give real-time status information.

Figure 2-9 GS-1116A Front Panel LEDs

Figure 2-10 GS-1124A Front Panel LEDs

The following table provides LED descriptions.

Table 2-3 Front Panel LED Descriptions

SYSTEM

LED COLOR STATUS DESCRIPTION

PWR

1000

LNK/ACT

Green

Green

Green

On The switch is turned on and receiving power.

Off The switch is off or not receiving power.

On A link to a 1000Mbps Ethernet device is up.

Blinking

Off The port is not connected to a 1000Mbps Ethernet device.

On The port is connecting with an Ethernet device.

Blinking The port is receiving or transmitting data.

Off No Ethernet device is attached.

A link to a 1000Mbps Ethernet device is up, and the port is
receiving or transmitting data.

Hardware Description and Installation 2-7

Dimension GS-1116A/GS-1124A Gigabit Switch

Chapter 3

Troubleshooting

This section describes common problems you may encounter with the switch in your network and

possible solutions.

3.1 Introduction

Troubleshoot the switch using the LEDs to detect problems.

3.1.1 PWR LED

The PWR LED on the front panel does not light up.

Table 3-1 Troubleshooting PWR LED

STEPS CORRECTIVE ACTION

1 Check the connections from your switch to the power source. Make sure you are using the supplied

power cord and that you are using a 100 - 240V AC, 50/60Hz power source.

2 Make sure the power source is turned on and that the switch is receiving sufficient power.

3 If these steps fail to correct the problem, contact your local distributor for assistance.

3.1.2 LNK/ACT LED

The LNK/ACT LED does not light up when a device is connected.

Table 3-2 Troubleshooting LNK/ACT LED

STEPS CORRECTIVE ACTION

1 Verify that the attached device(s) is turned on and properly connected to your switch.

2 Make sure the Ethernet adapters are working on the attached devices.

3 Verify that proper network cable type is used and its length does not exceed 100 meters. For more

information on network cable types, see Table 2-2.

3.1.3 1000 LED

The LEDs do not show the speed of my Ethernet device.

Table 3-3 Troubleshooting 1000 LEDs

STEPS CORRECTIVE ACTION

1 Check the connection between the switch and your Ethernet device(s).

2 Verify that you are using the proper cable type and that its length does not exceed 100 meters. For

more information on network cable types, see Table 2-2.

Troubleshooting 3-1

Dimension GS-1116A/GS-1124A Gigabit Switch

3.2 Improper Network Cabling and Topology

Improper network cabling or topology setup is a common cause of poor network performance and
network failure.

Table 3-4 Troubleshooting Improper Network Cabling and Topology

DESCRIPTION PROBLEMS AND CORRECTIVE ACTION

Faulty cables Using faulty network cables may affect data rates and have an impact on your network

performance. Replace with new standard network cables.

Non-standard network
cables

Cabling Length If you use longer cables than are needed, transmission quality may be affected.

Too many hubs
between the computers
in the network

A loop in the data path A data path loop forms when there is more than one path or route between two

Non-standard cables may increase the number of packet collisions and cause other
network problems that affect your network performance. Refer to Table
information on network cable types.

The network cables should not be longer than the limit of 100 meters.

Too many hubs (or repeaters) between the connected computers in the network may
increase the number of packet collisions or other network problems. Remove
unnecessary hubs from the network.

networked computers. This results in broadcast storms that will severely affect your
network performance. Make sure there are no loops in your network topology.

2-2 for more

3-2 Troubleshooting

Dimension GS-1116A/GS-1124A Gigabit Switch

Product Specifications

This section provides the specifications of the switch.

GENERAL

IEEE 802.3 10BASE-T Ethernet

IEEE 802.3u 100BASE-TX Fast Ethernet

Standards

Subscriber Interface

Uplink Interface

Media Interface Exchange All ports auto-sensing (auto MDI-/MDI-X)

Data Transfer Rate

Network Cables

Performance and Management

Packet Forwarding Rate

Switching Method Store-and-Forward switching architecture

MAC Address Table (Auto­learning)

Data Buffer

IEEE 802.3ab 1000Base-T

IEEE 802.3z Gigabit Fiber

IEEE 802.1p Class of Service

GS-1116A: 14x 1000Base-T Ethernet Ports

GS-1124A: 22x 1000Base-T Ethernet Ports

¾ Connector type: RJ-45

¾ Auto-MDIX

¾ Compliant with IEEE 802.3/3u

¾ Back pressure flow control for half duplex

¾ Flow control for full duplex (IEEE 802.3x)

2 GbE Dual Personality interface (Each dual personality has one 1000Base-T
copper port and one Small Form-Factor Pluggable (SFP) fiber port, with one
port active at a time.)

Fast Ethernet: 100Mbps (half duplex)/200Mbps (full duplex)

Gigabit Ethernet: 2000Mbps(full duplex)

10BASE-T: 2-pair UTP/STP Cat. 3, 4, 5 cable

EIA/TIA-568 100-ohm (100m)

100BASE-TX: 2-pair UTP/STP CAT. 5 cable

EIA/TIA-568 100-ohm (100m)

Gigabit Copper: 4 pair UTP/STP CAT. 5 cable

EIA/TIA 568 100-ohm (100M)

148800PPS for 100BASE-TX

1488000PPS for 1000BASE-T

GS-1116A: 8K entries

GS-1124A: 8K entries

GS-1116A: 340KB

GS-1124A: 500 KB

Product Specifications A

Dimension GS-1116A/GS-1124A Gigabit Switch

GS-1116A Switching fabric: 32Gbps. GS-1124A Switching fabric: 48Gbps

GS-1116A Memory Buffer: 340KB GS-1124A Memory Buffer: 500KB

Support Frame size: 1522 bytes

Layer 2 features

Physical Environment

LED

Power Supply 100 - 240V AC, 50/60Hz internal universal power supply

Power Consumption

Operating Temperature 0ºC to 45ºC (32ºF to 113ºF)

Operational Humidity 10% to 90% (Non-condensing)

EMI FCC Class A, CE

8K MAC addresses table

Jumbo frame support: Support 9Kbytes Jumbo frame size

CoS: Support 802.1p provided Tag based priority and per port 4 queues

Broadcast storm control

Power (green): Light on or off: Power on or off

1000Base-T Ethernet ports:

z 1000M green LED

¾ Light off: port is not connected at 1000M

¾ Light on: port is connected at 1000M

¾ Blinking: activity

z LNK/ACT: Green LED

¾ Light off: port disconnected

¾ Light on: port connected at 10M, 100M or 1000M

¾ Blinking: activity

GS-1116A: 13.25 W max

GS-1124A: 23.2 W max

B Product Specifications

Dimension GS-1116A/GS-1124A Gigabit Switch

Index

1000/ 100 Ethernet LED.............................. 2-4

802.3x .......................................................... 1-2

About the Dimension Gigabit Switch............. x

Auto MDI/MDIX.........................................2-4

Auto-negotiation.......................................... 2-3

Cabling Length ............................................3-2

Campus Environment ..................................1-1

CE .................................................................. iv

Certification ................................................... iv

class A............................................................ iv

Collisions .....................................................2-8

Contacting Customer Support......................... v

Copyright ........................................................ ii

CoS ..............................................................1-2

Data path loop.............................................. 3-2

Desktop Installation ..................................... 2-1

Installation

Desktop ....................................................2-1

Network Application

Backbone Switch......................................1-3

Network Cable Length Limit .......................2-7

Network Cable Types...................................2-7

1000Mbps ................................................2-7

100Mbps ..................................................2-7

Non-standard network cables.......................3-2

Normal User workgroup ..............................1-4

Package Contents .........................................1-3

Power Connection........................................2-3

Power Receptacle.........................................2-3

Product Specifications

General....................................................... A

Performance and Management................... A

Disclaimer....................................................... ii

Faulty cables ................................................ 3-2

FCC................................................................ iv

FCC Rules...................................................... iv

Features........................................................ 1-2

Federal Communications Commission (FCC)

Interference Statement ............................... iv

Front Panel................................................... 2-3

Front Panel Connections..............................2-6

Front Panel LED.......................................... 2-7

Front Panel LED Descriptions..................... 2-8

GBIC............................................................ 2-4

Gigabit Ethernet.............................................. x

High Bandwidth Backbone.......................... 1-1

IEEE 802.1p................................................. 1-2

Installation

Rack-Mounted .........................................2-2

Physical Environment ................................ A

Rack-mounted Installation ...........................2-2

Rear Panel ....................................................2-3

Related Documentation................................... x

Repair.............................................................iii

Return Material Authorization number..........iii

RJ-45 ports ...................................................2-3

Server Farm..................................................1-3

Service............................................................iii

Speed............................................................3-1

Store-and-Forward Switching ......................1-2

Super User workgroup .................................1-4

Syntax Conventions ........................................x

Trademarks .....................................................ii

Transceiver...................................................1-2

Transceiver Installation................................2-4

Transceiver Removal ...................................2-5

Index C

Dimension GS-1116A/GS-1124A Gigabit Switch

Troubleshooting

1000 LEDs ...............................................3-1

Troubleshooting

LK/ACT LED ..........................................3-1

PWR LED ................................................3-1

Troubleshooting

Network Cabling and Topology...............3-2

ventilation.................................................... 2-1

Ventilation Fan............................................ 2-3

Warranty........................................................ iii

Work Groups............................................... 1-4

ZyXEL Limited Warranty............................. iii

Note ........................................................... iii

ZyXEL Web Site.............................................x

D Index