The contents of this publication may not be reproduced in any part or as a whole, transcribed,
stored in a retrieval system, translated into any language, or transmitted in any form or by any
means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or
otherwise, without the prior written permission of ZyXEL Communications Corporation.
Published by ZyXEL Communications Corporation. All rights reserved.
Disclaimer
ZyXEL does not assume any liability arising out of the application or use of any products, or
software described herein. Neither does it convey any license under its patent rights nor the
patent rights of others. ZyXEL further reserves the right to make changes in any products
described herein without notice. This publication is subject to change without notice.
Trademarks
ZyNOS (ZyXEL Network Operating System) is a registered trademark of ZyXEL
Communications, Inc. Other trademarks mentioned in this publication are used for
identification purposes only and may be properties of their respective owners.
Copyright3
ZyXEL G-220 v2 User’s Guide
Federal Communications
Commission (FCC) Interference
Statement
The device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
undesired operations.
This equipment has been tested and found to comply with the limits for a Class B digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
If this equipment does cause harmful interference to radio/television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1 Reorient or relocate the receiving antenna.
2 Increase the separation between the equipment and the receiver.
3 Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
4 Consult the dealer or an experienced radio/TV technician for help.
Notice 1
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This product has been designed for the WLAN 2.4 GHz network throughout the EC region and
Switzerland, with restrictions in France.
Caution
1 The equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2).
2 This Transmitter must not be co-located or operating in conjunction with any other
Federal Communications Commission (FCC) Interference Statement5
ZyXEL G-220 v2 User’s Guide
ZyXEL Limited Warranty
ZyXEL warrants to the original end user (purchaser) that this product is free from any defects
in materials or workmanship for a period of up to two (2) years from the date of purchase.
During the warranty period, and upon proof of purchase, should the product have indications
of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or
replace the defective products or components without charge for either parts or labor, and to
whatever extent it shall deem necessary to restore the product or components to proper
operating condition. Any replacement will consist of a new or re-manufactured functionally
equivalent product of equal or higher value, and will be solely at the discretion of ZyXEL.
This warranty shall not apply if the product has been modified, misused, tampered with,
damaged by an act of God, or subjected to abnormal working conditions.
Note
Repair or replacement, as provided under this warranty, is the exclusive remedy of the
purchaser. This warranty is in lieu of all other warranties, express or implied, including any
implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in
no event be held liable for indirect or consequential damages of any kind to the purchaser.
To obtain the services of this warranty, contact ZyXEL's Service Center for your Return
Material Authorization number (RMA). Products must be returned Postage Prepaid. It is
recommended that the unit be insured when shipped. Any returned products without proof of
purchase or those with an out-dated warranty will be repaired or replaced (at the discretion of
ZyXEL) and the customer will be billed for parts and labor. All repaired or replaced products
will be shipped by ZyXEL to the corresponding return address, Postage Paid. This warranty
gives you specific legal rights, and you may also have other rights that vary from country to
country.
Online Registration
Register your product online to receive e-mail notices of firmware upgrades and information
at www.zyxel.com for global products, or at www.us.zyxel.com for North American products.
6ZyXEL Limited Warranty
ZyXEL G-220 v2 User’s Guide
Customer Support
Please have the following information ready when you contact customer support.
• Product model and serial number.
• Warranty Information.
• Date that you received your device.
• Brief description of the problem and the steps you took to solve it.
Congratulations on your purchase of the ZyXEL G-220 v2 802.11g Wireless USB Adapter.
Your ZyXEL G-220 v2 is easy to install and configure.
About This User's Guide
This manual is designed to guide you through the configuration of your ZyXEL G-220 v2 for
its various applications.
Related Documentation
• Supporting Disk
Refer to the included CD for support documents.
• Quick Start Guide
The Quick Start Guide is designed to help you get up and running right away. They
contain hardware installation/connection information.
• ZyXEL Glossary and Web Site
Please refer to www.zyxel.com for an online glossary of networking terms and additional
support documentation.
User Guide Feedback
Help us help you. E-mail all User Guide-related comments, questions or suggestions for
improvement to techwriters@zyxel.com.tw or send regular mail to The Technical Writing
Team, ZyXEL Communications Corp., 6 Innovation Road II, Science-Based Industrial Park,
Hsinchu, 300, Taiwan. Thank you.
Syntax Conventions
• “Enter” means for you to type one or more characters. “Select” or “Choose” means for
you to use one predefined choice.
• Mouse action sequences are denoted using a comma. For example, “In Windows, click
Start, Settings and then Control Panel” means first click the Start button, then point
your mouse pointer to Settings and then click Control Panel.
• “e.g.,” is a shorthand for “for instance”, and “i.e.,” means “that is” or “in other words”.
• The ZyXEL G-220 v2 802.11g Wireless USB Adapter may be referred to as the ZyXEL
G-220 v2 in this user’s guide.
Preface17
ZyXEL G-220 v2 User’s Guide
Graphics Icons Key
Wireless Access Point Computer Notebook Computer
Server Modem Wireless Signal
Telephone Switch Router
Internet Cloud
18Preface
This chapter introduces the ZyXEL G-220 v2 and prepares you to use the ZyXEL Utility.
1.1 About Your ZyXEL G-220 v2
The ZyXEL G-220 v2 is an IEEE 802.11g compliant wireless LAN adapter.
The following lists the main features of your ZyXEL G-220 v2. See the product specifications
in the appendix for detailed features.
• Proprietary SoftAP feature turns your ZyXEL G-220 v2 into an access point (AP).
• A built-in antenna
• Driver and utility support for Windows 98 Second Edition, Windows ME, Windows 2000
and Windows XP.
ZyXEL G-220 v2 User’s Guide
CHAPTER1
Getting Started
1.1.1 Application Overview
This section describes some network applications for the ZyXEL G-220 v2.
1.1.1.1 Infrastructure
To connect to a network via an Access Point (AP), set the ZyXEL G-220 v2 network type to
Infrastructure. Through the AP, you can access the Internet or the wired network behind the
AP.
Chapter 1 Getting Started19
ZyXEL G-220 v2 User’s Guide
Figure 1 Application: Infrastructure
1.1.1.2 Ad-Hoc
In case you prefer to set up a small independent wireless workgroup without an AP, use the
Ad-Hoc mode.
Ad-hoc mode does not require an AP or a wired network. Two or more wireless clients
communicate directly to each other.
Figure 2 Application: Ad-Hoc
20Chapter 1 Getting Started
1.1.1.3 Access Point Mode
You can set the ZyXEL G-220 v2 in access point mode. The following figure shows a network
example.
Figure 3 Application: Access Point Mode
In the example, the ZyXEL G-220 v2 is installed on computer A and set to operate in access
point mode. Computer A shares Internet connection to the wireless LAN, so wireless stations
B and C can access the Internet.
ZyXEL G-220 v2 User’s Guide
1.2 ZyXEL G-220 v2 Hardware and Utility Installation
Follow the instructions in the Quick Start Guide to install the ZyXEL Utility and make
hardware connections.
1.3 Configuration Methods
To configure your ZyXEL G-220 v2, use one of the following applications:
• Wireless Zero Configuration (WZC) (recommended for Windows XP)
• ZyXEL Utility (required when you want to use the ZyXEL G-220 v2 as an access point)
• Odyssey Client Manager (not supplied)
Note: Do NOT use the Windows XP configuration tool or the Odyssey Client Manager
and the ZyXEL Utility at the same time.
Refer to the Odyssey Client Manager documentation for more information.
1.4 Windows XP Users Only
Note: When you use the ZyXEL Utility, it automatically disables the Windows XP
wireless configuration tool.
Refer to the appendices on how to use WZC to manage the ZyXEL G-220 v2.
Chapter 1 Getting Started21
ZyXEL G-220 v2 User’s Guide
1.5 Accessing the ZyXEL Utility
After you install and start the ZyXEL Utility, an icon for the ZyXEL Utility appears in the
system tray.
Note: When the ZyXEL Utility system tray icon displays, the ZyXEL G-220 v2 is
installed properly.
When you use the ZyXEL Utility, it automatically disables the Windows XP
wireless configuration tool.
Figure 4 ZyXEL Utility: System Tray Icon
The color of the ZyXEL Utility system tray icon indicates the status of the ZyXEL G-220 v2.
Refer to the following table for details.
Table 1 ZyXEL Utility: System Tray Icon
COLORDESCRIPTION
RedThe ZyXEL G-220 v2 is operating in wireless station mode but is not connected to a
wireless network.
GreenThe ZyXEL G-220 v2 is operating in wireless station mode and connected to a wireless
network.
Pale BlueThe ZyXEL G-220 v2 is operating in access point mode.
Double-click on the ZyXEL Wireless LAN Utility icon in the system tray to open the ZyXEL
Utility. The ZyXEL Utility screens are similar in all Microsoft Windows versions. Screens for
Windows XP are shown.
Note: Click the icon (located in the top right corner) to display the on-line help
window.
1.6 Connecting to a Wireless LAN
This section shows you how to associate with a network using the ZyXEL Utility. You can
either manually connect to a network or configure a profile to have the ZyXEL G-220 v2
automatically connect to a specific network. Otherwise, configure nothing and leave the
ZyXEL G-220 v2 to automatically scan for and connect to any other available network
without security.
See the next chapters for detailed field descriptions.
22Chapter 1 Getting Started
1.6.1 Site Survey
After you install the ZyXEL Utility and then insert the ZyXEL G-220 v2, follow the steps
below to connect to a network using the Site Survey screen.
1 Make sure a wireless network is available and within range.
2 Open the ZyXEL Utility and click the Site Survey tab to open the screen as shown next.
3 Click Scan to search for available wireless networks.
Figure 5 ZyXEL Utility: Site Survey
ZyXEL G-220 v2 User’s Guide
4 To join a network, either click an SSID in the table and then click Connect or double-
click an SSID.
5 If the wireless security is activated for the selected wireless network, the Security
Setting screen displays. This screen varies according to the network’s encryption
method. Configure the same security settings as the associated network.
Note: If the selected network is unavailable or the security settings are not correct,
the ZyXEL G-220 v2 cannot connect to a network.
Chapter 1 Getting Started23
ZyXEL G-220 v2 User’s Guide
Figure 6 ZyXEL Utility: Security Setting
6 Verify that you have successfully connected to the selected network and check the
network information in the Link Info screen. If the ZyXEL G-220 v2 is not connected to
a network, the fields in this screen are blank.
Figure 7 ZyXEL Utility: Link Info
1.7 ZyXEL G-220 v2 Modes
You can set your ZyXEL G-220 v2 to operate in either wireless station or access point (AP)
modes.
In wireless station mode, your ZyXEL G-220 v2 must connect to a peer wireless station or an
AP to take part in your wireless network.
24Chapter 1 Getting Started
In access point mode, your ZyXEL G-220 v2 functions as an access point. This allows you to
set up your wireless network without using a dedicated AP device. Up to 16 wireless stations
can associate to the ZyXEL G-220 v2 to form a wireless network. Refer to Section 1.7.1 on
page 25 and Chapter 4 on page 53 for more information.
Note: With WZC, you cannot use the ZyXEL G-220 v2 as an access point.
1.7.1 Change ZyXEL G-220 v2 Mode
To change between the modes, select either the Station Mode or AP Mode option in any
ZyXEL Utility screens.
Figure 8 ZyXEL Utility: Change Modes
ZyXEL G-220 v2 User’s Guide
Note: Wait for about five seconds for the ZyXEL Utility to complete the mode change.
The current mode is indicated by the color of the check box.
1.8 ZyXEL Utility Screen Summary
This sections describes the ZyXEL Utility screens.
Chapter 1 Getting Started25
ZyXEL G-220 v2 User’s Guide
Figure 9 Menu Summary: Station Mode
Figure 10 Menu Summary: AP Mode
The following table describes the menus.
Table 2 ZyXEL Utility: Menu Screen Summary
TABDESCRIPTION
Station Mode
Link InfoUse this screen to see your current connection status, configuration and data rate
Site SurveyUse this screen to
ProfileUse this screen to add, delete, edit or activate a profile with a set of wireless and
AdaptorUse this screen to configure a transfer rate, enable power saving and use OTIST
AP Mode
Link InfoUse this screen to see your current connection status, configuration and data rate
Configuration Use this screen to configure wireless LAN settings.
MAC FilterUse this screen to configure which computer(s) you want access to the wireless
statistics.
•scan for a wireless network
•configure wireless security (if activated on the selected network).
•connect to a wireless network.
security settings.
(One-Touch Intelligent Security Technology).
statistics.
LAN through the ZyXEL G-220 v2.
26Chapter 1 Getting Started
Wireless LAN Network
This chapter provides background information on wireless LAN network.
2.1 Wireless LAN Overview
This section describes the wireless LAN network terms and applications.
2.1.1 SSID
The SSID (Service Set Identity) is a unique name shared among all wireless devices in a
wireless network. Wireless devices must have the same SSID to communicate with each other.
ZyXEL G-220 v2 User’s Guide
CHAPTER2
2.1.2 Channel
A radio frequency used by a wireless device is called a channel.
2.1.3 Transmission Rate (Tx Rate)
The ZyXEL G-220 v2 provides various transmission (data) rate options for you to select.
Options include Fully Auto, 1 Mbps, 2 Mbps, 5.5 Mbps, 6 Mbps, 9 Mbps, 11 Mbps, 12 Mbps, 18 Mbps, 24 Mbps, 36 Mbps, 48 Mbps and 54 Mbps. In most networking scenarios,
the factory default Fully Auto setting proves the most efficient. This setting allows your
ZyXEL G-220 v2 to operate at the maximum transmission (data) rate. When the
communication quality drops below a certain level, the ZyXEL G-220 v2 automatically
switches to a lower transmission (data) rate. Transmission at lower data speeds is usually more
reliable. However, when the communication quality improves again, the ZyXEL G-220 v2
gradually increases the transmission (data) rate again until it reaches the highest available
transmission rate. You can select any of the above options. If you wish to balance speed versus
reliability, select 54 Mbpsin a networking environment where you are certain that all wireless
devices can communicate at the highest transmission (data) rate. 1 Mbps or 2 Mbps are used
often in networking environments where the range of the wireless connection is more
important than speed.
Note: With USB1.0/1.1, the ZyXEL G-220 v2 can only transmit at up to 11Mbps.
2.2 Wireless LAN Security Overview
Wireless LAN security is vital to your network to protect wireless communications.
Chapter 2 Wireless LAN Network27
ZyXEL G-220 v2 User’s Guide
Configure the wireless LAN security using the Configuration or the Profile Security Setting
screen. If you do not enable any wireless security on your ZyXEL G-220 v2, the ZyXEL G220 v2’s wireless communications are accessible to any wireless networking device that is in
the coverage area.
2.2.1 Data Encryption with WEP
WEP (Wired Equivalent Privacy) encryption scrambles all data packets transmitted between
the ZyXEL G-220 v2 and the AP or other wireless stations to keep network communications
private. Both the wireless stations and the access points must use the same WEP key for data
encryption and decryption.
There are two ways to create WEP keys in your ZyXEL G-220 v2.
• Automatic WEP key generation based on a “password phrase” called a passphrase. The
passphrase is case sensitive. You must use the same passphrase for all WLAN adapters
with this feature in the same WLAN.
For WLAN adapters without the passphrase feature, you can still take advantage of this
feature by writing down the four automatically generated WEP keys from the Security Setting screen of the ZyXEL Utility and entering them manually as the WEP keys in the
other WLAN adapter(s).
• Enter the WEP keys manually.
Your ZyXEL G-220 v2 allows you to configure up to four 64-bit, 128-bit or 256-bit WEP
keys and only one key is used as the default key at any one time.
2.2.2 IEEE 802.1x
The IEEE 802.1x standard outlines enhanced security methods for both the authentication of
wireless stations and encryption key management. Authentication can be done using an
external RADIUS server.
2.2.2.1 EAP Authentication
EAP (Extensible Authentication Protocol) is an authentication protocol that runs on top of the
IEEE 802.1x transport mechanism in order to support multiple types of user authentication. By
using EAP to interact with an EAP-compatible RADIUS server, an access point helps a
wireless station and a RADIUS server perform authentication.
The type of authentication you use depends on the RADIUS server and an intermediary AP(s)
that supports IEEE 802.1x. The ZyXEL G-220 v2 supports EAP-TLS and EAP-PEAP. Refer
to Appendix E on page 89 for descriptions.
For EAP-TLS authentication type, you must first have a wired connection to the network and
obtain the certificate(s) from a certificate authority (CA). A certificate (also called digital IDs)
can be used to authenticate users and a CA issues certificates and guarantees the identity of
each certificate owner.
28Chapter 2 Wireless LAN Network
2.2.3 WPA(2)
Wi-Fi Protected Access (WPA) is a subset of the IEEE 802.11i standard. WPA2 (IEEE
802.11i) is a wireless security standard that defines stronger encryption, authentication and
key management than WPA.
Key differences between WPA(2) and WEP are improved data encryption and user
authentication.
If both an AP and the wireless clients support WPA2 and you have an external RADIUS
server, use WPA2 for stronger data encryption. If you don't have an external RADIUS server,
you should use WPA2-PSK (WPA2-Pre-Shared Key) that only requires a single (identical)
password entered into each access point, wireless gateway and wireless client. As long as the
passwords match, a wireless client will be granted access to a WLAN.
If the AP or the wireless clients do not support WPA2, just use WPA or WPA-PSK depending
on whether you have an external RADIUS server or not.
Select WEP only when the AP and/or wireless clients do not support WPA or WPA2. WEP is
less secure than WPA or WPA2.
ZyXEL G-220 v2 User’s Guide
2.2.3.1 Encryption
Both WPA and WPA2 improve data encryption by using Temporal Key Integrity Protocol
(TKIP), Message Integrity Check (MIC) and IEEE 802.1x. WPA and WPA2 use Advanced
Encryption Standard (AES) in the Counter mode with Cipher block chaining Message
authentication code Protocol (CCMP) to offer stronger encryption than TKIP.
The encryption mechanisms used for WPA(2) and WPA(2)-PSK are the same. The only
difference between the two is that WPA(2)-PSK uses a simple common password, instead of
user-specific credentials. The common-password approach makes WPA(2)-PSK susceptible to
brute-force password-guessing attacks but it’s still an improvement over WEP as it employs a
consistent, single, alphanumeric password to derive a PMK which is used to generate unique
temporal encryption keys. This prevent all wireless devices sharing the same encryption keys.
(a weakness of WEP).
2.2.3.2 User Authentication
WPA and WPA2 apply IEEE 802.1x and Extensible Authentication Protocol (EAP) to
authenticate wireless stations using an external RADIUS database. WPA2 reduces the number
of key exchange messages from six to four (CCMP 4-way handshake) and shortens the time
required to connect to a network. Other WPA2 authentication features that are different from
WPA include key caching and pre-authentication. These two features are optional and may not
be supported in all wireless devices.
2.2.4 WPA(2)-PSK Application Example
A WPA(2)s-PSK application looks as follows.
Chapter 2 Wireless LAN Network29
ZyXEL G-220 v2 User’s Guide
1 First enter identical passwords into the AP and all wireless clients. The Pre-Shared Key
(PSK) must consist of between 8 and 63 ASCII characters or 64 hexadecimal characters
(including spaces and symbols).
2 The AP checks each client's password and (only) allows it to join the network if it
matches its password.
3 The AP and wireless clients use the pre-shared key to generate a common PMK.
4 The AP and wireless clients use the TKIP or AES encryption process to encrypt data
exchanged between them.
Figure 11 WPA-PSK Authentication
2.2.5 WPA(2) with RADIUS Application Example
You need the IP address of the RADIUS server, its port number (default is 1812), and the
RADIUS shared secret. A WPA(2) application example with an external RADIUS server
looks as follows. "A" is the RADIUS server. "DS" is the distribution system.
1 The AP passes the wireless client's authentication request to the RADIUS server.
2 The RADIUS server then checks the user's identification against its database and grants
or denies network access accordingly.
3 The RADIUS server distributes a Pairwise Master Key (PMK) key to the AP that then
sets up a key hierarchy and management system, using the pair-wise key to dynamically
generate unique data encryption keys to encrypt every data packet that is wirelessly
communicated between the AP and the wireless clients.
30Chapter 2 Wireless LAN Network
Loading...
+ 79 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.