ZyXEL Prestige 660R-6 Read Me First
Prestige 660R-6x Read Me First
PPrreessttiiggee RReeaarr PPaanneell CCoonnnneeccttiioonnss
PORT CONNECTION
DSL Connect the DSL port on the Prestige to the wall jack using the included DSL cable (telephone wire).
Connect the micro filter(s) (optional – see the appendix in your User’s Guide for details) between the wall
jack and your telephone(s).
Be careful not to insert an RJ-11 connector into the RJ-45 port.
LAN 10/100M Use an Ethernet cable to connect this port to a computer (with an Ethernet card) or a hub (if your network
has more than one computer). The port is auto-negotiating (can connect at 10 or 100Mbps) and autocrossover (automatically adjust to straight-through or crossover Ethernet cable).
RESET You only need to use this button if you have forgotten the Prestige’s password or IP address. It returns the
Prestige to the factory defaults.
POWER Connect the end of the included power adaptor for your region to this power socket.
After you’ve made the connections, connect the power adaptor to a power supply and push in the power button to turn on the
Prestige.
PPrreessttiiggee FFrroonntt PPaanneell LLEEDD DDeessccrriippttiioonn
LED
SYS Green
COLOR STATUS DESCRIPTION
Green On The Prestige is receiving power. PWR
Off The Prestige is not receiving power.
On The Prestige is functioning properly.
Blinking The Prestige is restarting.
Off The Prestige is not ready or has malfunctioned.
PPrreessttiiggee FFrroonntt PPaanneell LLEEDD DDeessccrriippttiioonn
LED
Red On The power to the Prestige is too low.
LAN 10M Green
LAN 100M
DSL Green
PPP/ACT
COLOR STATUS DESCRIPTION
On The Prestige has a successful 10Mbps Ethernet connection.
Blinking The Prestige is receiving or sending data.
Off No device is connected at 10Mbps.
Amber On The Prestige has a successful 100Mbps Ethernet connection.
Blinking The Prestige is receiving or sending data.
Off No device is connected at 100Mbps.
On The Prestige is linked successfully to a DSLAM.
Blinking The Prestige is initializing the DSL line.
Off The DSL link is down.
Green Blinking The Prestige is sending or receiving non-PPP traffic.
On The Prestige has a PPP (PPPoA or PPPoE) connection. Amber
Blinking The Prestige is sending or receiving PPPoA or PPPoE traffic.
Off The Prestige is ready but not sending or receiving data.
Press the power switch in. The Power LED turns on. The SYS LED blinks and turns steady on. The
LAN and DSL LEDs turn on, if they are properly connected.
PPrreessttiiggee FFaaccttoorryy DDeeffaauullttss
LAN IP Address 192.168.1.1 Default Password 1234
Subnet Mask 255.255.255.0 DHCP IP Pool 192.168.1.33 – 192.168.1.64
IInntteerrnneett AAccccoouunntt IInnffoorrmmaattiioonn
Your ISP (Internet Service Provider) or telephone company should give you most of the following information or pre-
configured the Prestige with it when you signed up for your Internet access account. You do not need to know every field.
REQUIRED INFORMATION
Virtual Path Identifier (VPI): ____________
Virtual Channel Identifier (VCI): ____________
Multiplexing (VC-based or LLC-based):
Your device’s WAN IP Address (if given): __________________
Encapsulation:
RFC 1483
ENET ENCAP
PPPoA
PPPoE
Ethernet Encapsulation Gateway IP Address: ____________________
User Name: ____________ Password: ____________
(PPPoE) Service Name: ____________
User Name: ____________ Password: ____________
VC LLC
Loading...