Zhone Technologies 6228-I2-xxx User Manual

Bonded ADSL2+ can
provide significant rate and reach improvements over single line ADSL2+ deployments.
Auto-connect feature will
Configurable as either a
Bridge or Router
802.11b/g Wireless Access
Point
IGMP v1/v2 support for
video deployments
Filter traffic based on
Destination or Source IP Address and MAC Addresses
Traffic Class Rules based
on Protocol, Source IP, Source Port, Destination IP, Destination Port,
802.1p
Bonded ADSL2+ 4Port Modem with WiFi
6228-I2-xxx
Bonded ADSL2+ 4 Port Switch WiFi Bridge/Router
The 6200 ADSL2+ family of endpoints deliver the required performance for multimedia applications at very competitive price points. The 6200 ADSL2+ endpoints, in compact form factor, have been successfully used for residential, business, in-building deployments such as hotel/motel, temporary housing, and dormitory-campus installations for high-speed internet access (HSIA) and video-on-demand services.
The Zhone 6200 ADSL2+ endpoints are easily user-installed. The embedded web-based user interface is designed to simplify ADSL deployment. All products provide an Ethernet connection that is auto-sensing, eliminating the worry about connection cable type (straight-through vs crossover).
DELT or Dual End Loop Test, is a feature that is present the 6200 Family of ADSL2+ CPEs. DELT is primarily used for reactive tests on a loop after a modem has been deployed—either to help troubleshoot a line or to capture a baseline of loop characteristics at the time of installation. Because DELT is a dual-ended test, it requires equipment that supports the DELT feature at both ends of the copper loop. While this prevents DELT from being used on loops where no CPE has yet been deployed, DELT in turn offers a deeper set of loop tests, and can provide very valuable information on the condition of a copper loop.
Default settings make for a quick and easy installation that doesn't require any configuration.
The modem, when operating in router mode, support DHCP Server/Relay/Client, NAPT, as well as RIP, dynamic routing, port forwarding, and static routing. For security, firewall functions including PAP/CHAP authentication and IP filtering are supported.
Technical Specifications
Dimensions
1.2" (3.0cm) High x 6.5" (16.5cm) Wide x 4.4"
(11.2cm) Deep
Weight
1.5 lbs (0.7 kg)
Power
100 VAC, 50 Hz
110 VAC, 60 Hz
220 VAC, 50/60 Hz
Interfaces
DSL Line: RJ11 with 4 active pins
Ethernet: 4 Port 10/100BaseT
Wireless: 802.11b/g
Wireless Support
Supports IEEE 802.11b and 802.11g
simultaneously
Conforms to Wireless Ethernet Compatibility
Alliance (WECA)
Modulation: DFDM with BPSK, QPSK, 16QAM,
64QAM, D8PSK
Wireless Media Access Protocol: CSMA/CA with
ACK
Supports network authentication: Open, Shared
(WEP 16-bit or 128-bit), 802.1X, WPA, WPA-PSK, WPA2, WPA2-PSK, Mixed WPA2/WPA, Mixed WPA2/WPA-PSK
Wireless MAC Filter
AP Isolation - Wireless clients can not
communicate with each other when enabled
Xpress Technology - can improve aggregate
throughput by up to 75% in mixed networks.
Bonded ADSL2+ 4Port Modem with WiFi
Standards Support
ATM Support
- ITU-T I.610 F4/F5 OAM Send and Receieve/Loop back
- Support for 8 PVC's
- RFC 1483/2684 (Bridged/Routed Ethernet over ATM)
Routing/Bridge Support
- Transparent Bridge Support
- DHCP Server/Relay/Client
- DNS Relay Agent
- Dynamic DNS Support
- DMZ support
- Static Routing
- RIPv1 and RIPv2
- Policy based QoS (TOS, 802.1p, Source/Destination IP Address, Source/Destination Port, Protocol)
- IGMP v1/v2
PPP Support
- PAP/CHAP authentication
- PPPoA
- PPPoE
Security
- NAT for Basic Firewall support
- Ingress and Egress Packet Filtering
- Parental Control
- MAC Filtering
- Stateful Packet Inspection
DELT support
Protocol Support
ANSI T1.413 (Full Rate ADSL)
ITU G.992.1 (DMT)
ITU G.992.2 (G.lite)
ITU G.992.3 (ADSL2)
ITU G.992.5 (ADSL2+)
ITU G.994.1 (G.hs)
ITU G.997.1
Annex L
Annex M
G.Bond
Management
Web-based Configuration GUI
CLI
Telnet Remote Management
SNMP Support
FTP/TFTP firmware upgrade and configuration
backup/restore
Syslog Support
TR-069
Regulatory Compliance
FCC Part 15, Part 68
CE
UL
TUV
Operating Requirements
Operating Temperature: 32° F to 104° F (0° C to
40° C)
Storage Temperature: –4° F to 149° F (–20° C to
65° C)
Humidity: 5% to 95%, non-condensing
Channels 1 ~ 14
Total Transmission Power (EIRP) - 18dbm as to
pass from the NTRA
Range ~100ft
Frequency Range ~ 2.400 - 2.480GHz
Ordering Information
6228-I2-200 Bonded ADSL2+ CPE Router, 802.11G WiFi, N.A.
6228-I2-300 Bonded ADSL2+ CPE Router, 802.11G WiFi, U.K.
6228-I2-302 Bonded ADSL2+ CPE Router, 802.11G WiFi, Euro
2008/02/21 11:14:00
Loading...