Zenith C30W47 Installation And Operating Manual, Warranty

© Copyright 2004, LG Electronics USA, Inc.

Installation and Operating Guide | Warranty

Model Number | C30W47 | Direct View TV

PAGE 2

206-04007

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equip­ment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com­munications. However, there is no guarantee that interference will not occur in a particular installation. If this equip­ment does cause harmful interference to radio or television reception, which can be determined by turning the equip­ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.
Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this device compliance is:
Zenith Electronics Corporation
1-201-816-2000
Marked and Distributed in the United States by LG Electronics U.S.A., Inc.
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
http://www.zenith.com

WARNING

RISK OF ELECTRIC SHOCK
DO NOT OPEN

PAGE 3

206-04007

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical
shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and
observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation
that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

(Continued on next page)

1. Read Instructions

All the safety and operating instructions should be read
before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained
for future reference.

4. Heed Warnings

All warnings on the product and in the operating instruc­tions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.

6. Water and Moisture

Do not use this product near water, for example, near a
bath tub, wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface,
or on an unstable cart, stand, tripod, bracket, or table.
The product may slide or fall, causing serious injury to a
child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recom­mended by the manufacturer, or sold with the product.
Any mounting of the product should follow the manufac­turer’s instructions, and should use a mounting accessory
recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product
manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventila­tion and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not
be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in
a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply to your home, con­sult your product dealer or local power company. For prod­ucts intended to operate from battery power, or other
sources, refer to the operating instructions.

12. Power-Cord Polarization

This product is equipped with a polarized alternating-cur­rent line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If
the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety pur­pose of the polarized plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they
exit from the product.

PORTABLE CART WARNING

IMPORTANT SAFETY INSTRUCTIONS

PAGE 4

206-04007

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded
to provide protection against voltage surges and built-up
static charges. Article 810 of the National Electrical Code
(U.S.A.), ANSI/ NFPA 70 provides information with regard
to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna­discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.

16. Power Lines

An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be
fatal.

17. Overloading

Do not overload wall outlets and extension cords as this
can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servic­ing to qualified service personnel under the following con­ditions:

a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into

the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.

e. If the product has been dropped or the cabinet has
been damaged.

f. If the product exhibits a distinct change in perfor­mance.

21. Replacement Parts

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the origi­nal part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condi­tion.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as
recommended by the manufacturer. The product may slide
or fall, causing serious injury to a child or adult, and seri­ous damage to the product.

24. Heat

The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.

Antenna Lead in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductor
(NEC Section 810-21)

Ground Clamps

Power Service Grounding
Electrode System (NEC
Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical
Code Instructions

Fig. 1

NEC - National Electrical Code

IMPORTANT SAFETY INSTRUCTIONS

PAGE 5

206-04007

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Important Safety Instructions . . . . . . . . . . . . . . . . .3-4

Step 1. Hook Up TV

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . .6

Rear Connections Panel . . . . . . . . . . . . . . . . . . . . . . .7

Side Connections Panel (Side Video) . . . . . . . . . . . . . . .8

ANT/Cable Service Hookup . . . . . . . . . . . . . . . . . . . . .9

Cable Box Connections . . . . . . . . . . . . . . . . . . . . . . .10

VCR Connections . . . . . . . . . . . . . . . . . . . . . . . . . . .11

DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Set-top Box Hookup . . . . . . . . . . . . . . . . . . . . . . . .13

Monitor Out Setup . . . . . . . . . . . . . . . . . . . . . . . . .14

External Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Digital Audio Output . . . . . . . . . . . . . . . . . . . . . . . .16

Turning the TV on . . . . . . . . . . . . . . . . . . . . . . . . . .17

On-Screen Displays . . . . . . . . . . . . . . . . . . . . . . . . .17

Remote Control Functions in TV Mode . . . . . . . . . . .18-19

Step 2. Customize your TV’s Features

SETUP Menu

EZ Scan (Channel Search) . . . . . . . . . . . . . . . . . .20-21

Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

DTV Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Channel Label Setup . . . . . . . . . . . . . . . . . . . . . . .24

Main Picture Source Selection . . . . . . . . . . . . . . . . . 25

PIP (Picture-In-Picture) Options . . . . . . . . . . . . .26-27

POP (Picture-outside-Picture) Source . . . . . . . . . . . . .28

Multi Point Zooming . . . . . . . . . . . . . . . . . . . . . . .28

Twin Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

VIDEO Menu

EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Manual Video Control . . . . . . . . . . . . . . . . . . . . . . .31

Color Temperature . . . . . . . . . . . . . . . . . . . . . . . . .32

Z-View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Video Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

AUDIO Menu

Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . .33

EZ SoundRite . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . .34

EZ Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Manual Sound Control . . . . . . . . . . . . . . . . . . . . . .35

Turn TV Speakers on/off . . . . . . . . . . . . . . . . . . . . .35

Front Surround . . . . . . . . . . . . . . . . . . . . . . . . . . .36

TIME Menu

Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . .37

Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . .38

TV Turn Off Time Setup . . . . . . . . . . . . . . . . . . . . .39

TV Turn On Time Setup . . . . . . . . . . . . . . . . . . . . . .40

Sleep Timer Setup . . . . . . . . . . . . . . . . . . . . . . . . .41

Auto off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

OPTION Menu

Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . . . .43

Closed Captions . . . . . . . . . . . . . . . . . . . . . . . .44-45

Caption Option Menu . . . . . . . . . . . . . . . . . . . . . . .46

On-Screen Menu Languages . . . . . . . . . . . . . . . . . . .47

Velocity Modulation . . . . . . . . . . . . . . . . . . . . . . . .47

Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Degaussing the screen . . . . . . . . . . . . . . . . . . . . . .48

Cinema Mode Setup . . . . . . . . . . . . . . . . . . . . . . . .49

EZ Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

LOCK Menu

Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .51-52

Step 3. Miscellaneous

Programming the Remote . . . . . . . . . . . . . . . . . . . . .53

Programming Codes . . . . . . . . . . . . . . . . . . . . . .54-56

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .57-58

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .59-60

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61-62

Product Specifications . . . . . . . . . . . . . . . . . . . . . .63

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Note: Design and specifications are subject to change without prior notice.

PAGE 6

206-04007

Front Panel Controls

power

Standby indicator (Illuminates brightly when the TV is
in standby mode. Dims when the TV is switched on.)

Remote control sensor

tv/video

menu

vol left/ right
Volume(

G) button increases the sound level and vol-

ume(

F) button decreases the sound level.

ch (Channel) up / down

1

2

3
4

These buttons work just as they do on your
remote control.

5
6

7

tv/video

menu

vol

ch

power

1

2

4

3

6

7

5

PAGE 7

206-04007

Rear Connections Panel

Mini glossary

JACK A connection on the back of a TV, VCR, or any other A/V device. This includes the RF jack and the Audio/Video jacks that are color-

coded.

SIGNAL Picture and sound traveling through cable, or over the air, to your television screen.

CALIBRATION

DIGITAL
AUDIO OUTPUT
OPTICAL

DVD/DTV INPUT

VIDEO

VIDEO

AUDIO

L(MONO) R

ANTENNA1 ANTENNA2

DVI-HDTV INPUT

DIGITAL
AUDIO INPUT1
OPTICAL
(COMPONENT1)

DIGITAL
AUDIO INPUT2
OPTICAL
(DVI)

PR

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

S-VIDEO VIDEO/AUDIO INPUT MONITOR OUTPUT

VARIABLE

AUDIO

PB

Y

L

R

IN1

IN2

IN3

AUDIO

P

R

PB

Y

L

R

AUDIO

R

L

AUDIO

R

L

AUDIO

+75 Ω +75 Ω

S-Video In

A connection available
with some high-end
equipment that provides
even better picture
quality for Video 1, 2.

RF Connectors:
Antenna1 Input,
Antenna2 Input

Used to connect
cable or antenna sig­nals to the television,
either directly or
through your cable
box.

Video 1, 2 and 3 Inputs

Connects the video signals
from various types of
equipment.

Y, P

B, PR

DVD Component Video and HD
Component Video

Some top-of-the-line DVD players use
what is called “component video,” for
extremely accurate picture reproduc­tion. Refer to your DVD manual for

further information.

Connecting external equipment to your TV.

Monitor Out

Connects to a second
TV or Monitor.

Left/Right Audio

Used for stereo sound
from various types of
equipment.

Component Left/Right
Audio

Used for stereo sound from
various types of equipment.

Variable Audio Out

Used to connect
either an external
amplifier, or add a
sub-woofer to your
surround sound system.

DVI-HDTV Input

Used to connect

from a DTV source.

Digital Audio

Output Optical

Connects to external

audio equipment

like a home theater

system.

Digital Audio

Input1 Optical

Connects to digital

audio from various

types of equipment.

Digital Audio

Input2 Optical

Used in audio

connection from a

DTV source.

PAGE 8

206-04007

Front Connections Panel

Side A/V Panel

S-video

video in

L/mono

Audio

R

side video

There are four jacks on the lower-right front
side of your TV that make connecting
Audio/Video devices like video games and
camcorders very simple.

The jacks are like those found on the back
jack connection panel. This means that most
equipment that connects to those types of
jacks on the rear jackpack, may be connected
to the Side connection panel (Side Video).

To use the Side jacks as the signal source,
select them using Main input menu as
described on page 25. They will be named
“Side Video” in the Main input menu.

Left/Right Audio

Used for stereo sound
from various types of
equipment.

Video in

Connects the video
signals from any
piece of equipment.

S-Video

A connection available on some very
high-end equipment that provides
better picture quality than video
input.

When you select Side video or Side
S-Video, the Front Audio inputs
are automatically selected as well.

Do not connect to both Video and
S-Video at the same time.
Connect either Video or S-Video
only.

Mini glossary

A/V CABLES Audio/Video cables. Three cable connector—Right audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo

playback of videocassettes and for higher quality picture and sound from other A/V devices.

A/V DEVICE Any device that produces video (picture) and/or audio (sound) (VCR, DVD, cable box, or television).

PAGE 9

206-04007

Antenna / Cable Service Hookup

1

Connect an antenna and/or cable service to
your TV as shown.

Turn to page 20 to do a channel search
with EZ Scan.

For best signal reception, it is recommended to have your Antenna professionally adjusted.

2

If you receive your RF signal through an
antenna that is several years old and con­nects with two small prongs, you will need to
purchase a 300 to 75 ohm adapter. It should
be available from your local
electronics dealer.

We recommend using a 75 ohm cable for
your antenna connection in order to prevent
interference.

CALIBRATION

DIGITAL
AUDIO OUTPUT
OPTICAL

ANTENNA 1 ANTENNA 2

DIGITAL
AUDIO INPUT1
OPTICAL
(COMPONENT1)

+75 Ω +75 Ω

Antenna

Cable TV
Wall jack

RF coaxial wire
(75 ohm)

RF coaxial wire
(75 ohm)

Mini glossary

TV OVER-THE-AIR SIGNALS DTV DIGITAL OVER-THE-AIR SIGNALS
CATV CABLE SIGNALS CADTV DIGITAL CABLE SIGNALS

Combined signals

TV/CATV/DTV Over-the-air, cable, and digital over-the-air signals
TV/CATV/CADTV Over-the-air, cable, and digital cable signals

CAUTION : If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-type searches. The TV will let

you know when the analog, cable, and digital channel scans are complete.

PAGE 10

206-04007

Cable Box Connections

If you’re using a cable box, leave the TV on
channel 3 or 4 and use your cable box to
change channels.

Locate the output jack on the back of
your cable box. Connect this to the
Antenna 1 jack on the back of your TV.

Or find the composite video and audio
jacks on the back of your cable box, and
connect them following the instructions
provided with your equipment.
This can be combined with any other
equipment you may want to hook up.

1

In

Output
Switch

Out

Audio

TV

VCR

L

R

Video

3 4

DVD/DTV INPUT

VIDEO

AUDIO

L(MONO) R

ANTENNA 1 ANTENNA 2

PR

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

S-VIDEO VIDEO/AUDIO INPUT

P

B

Y

L

R

IN1

IN2

IN3

AUDIO

P

R

PB

Y

L

R

AUDIO

+75 Ω +75 Ω

Cable box

RF coaxial wire

(75 ohm)

Cable box

Back AV panel

PAGE 11

206-04007

VCR Connections

1

Locate the Antenna 1 jack on the
back of your TV. Connect this to
out jack on the back of your VCR.

Or find the composite video and
audio jacks on the back of your
VCR, and connect them following
the instructions provided with
your equipment.

You may connect either the com­posite video or the S-Video cables
to your TV. (Do not connect BOTH
the composite and the S- Video
cables. In the event that you con­nect both composite and the S­Video cables, only the S-Video will
work.)

To hear stereo sound from cable or your VCR,
you will need to connect A/V cables as well as
the wire that runs from the VCR to your TV.

If you want to receive your signals on Channel
3 or 4, locate the Out to TV jack on your VCR.
Connect a cable from the Out to TV jack to the
Antenna1 jack on the back of your TV.

In

Out

Audio

L

R

Video

3 4

S-Video

Output
Switch

DVD/DTV INPUT

VIDEO

AUDIO

L(MONO) R

ANTENNA 1 ANTENNA 2

PR

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

S-VIDEO VIDEO/AUDIO INPUT

P

B

Y

L

R

IN1

IN2

IN3

AUDIO

P

R

PB

Y

L

R

AUDIO

+75 Ω +75 Ω

RF coaxial wire
(75 ohm)

A/V cables
not included
with TV

or

VCR

Back AV panel

PAGE 12

206-04007

DVD Player

Mini glossary

COMPONENT VIDEO Some video equipment uses three separate lines (Y, P

B, PR) to more precisely reproduce images. Your manual will explain how

this relates to your equipment.

1

2

R

Audio
LR

S-Video

CALIBRATION

DIGITAL
AUDIO OUTPUT
OPTICAL

DVD/DTV INPUT

VIDEO

AUDIO

L(MONO) R

ANTENNA 1 ANTENNA 2

DVI-HDTV INPUT

DIGITAL
AUDIO INPUT1
OPTICAL
(COMPONENT1)

DIGITAL
AUDIO INPUT2
OPTICAL
(DVI)

PR

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

S-VIDEO VIDEO/AUDIO INPUT

P

B

Y

L

R

IN1

IN2

IN3

AUDIO

P

R

PB

Y

L

R

AUDIO

+75 Ω +75 Ω

Component input jacks

on the TV

Y

PB

PR

Video output jacks
of DVD player

Y
Y
Y
Y

Pb

B-Y

Cb
PB

Pr

R-Y

Cr
P

R

• Component Input ports

You can get better picture quality if you
connect a DVD player using the component
input ports as shown below.

A/V cables
not included
with TV

DVD player

Back AV panel

or

Back AV panel

Find the component or S-Video
jacks for video connections,
depending on your DVD connec­tors. Then make the correspond­ing audio connections. See the
diagram for either set up.

You may connect either the
composite video or the S-Video
cables to your TV. Do not con­nect both the composite and
the S-Video.

Some high-end DVD players use
a picture reproduction system
called “component video.” If
your DVD player has component
output, use the connectors
marked “Component 1 or 2” on
the jack panel. Please refer to
your DVD manual for proper
installation.

CALIBRATION

DIGITAL
AUDIO OUTPUT
OPTICAL

ANTENNA 1 ANTENNA 2

DVI-HDTV INPUT

DIGITAL
AUDIO INPUT1
OPTICAL
(COMPONENT1)

DIGITAL
AUDIO INPUT2
OPTICAL
(DVI)

DVD/DTV INPUT

P

R

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

PB

Y

L

R

AUDIO

P

R

PB

Y

L

R

AUDIO

Audio
LR

Digital Audio

Optical

Component Video

+75 Ω +75 Ω

DVD player

or

A/V cables
not included
with TV

PAGE 13

206-04007

Set-top box Hookup

Find the audio and Y, PB, PR jacks or DVI
output port on the back of your set-top
box and connect them following the
instructions provided with your equip­ment.

Connect these cables to your TV as
shown.

1

2

Digital Audio

Optical Output

Audio

L R

Component Out

Y Pb Pr

CALIBRATION

DIGITAL
AUDIO OUTPUT
OPTICAL

ANTENNA 1 ANTENNA 2

DVI-HDTV INPUT

DIGITAL
AUDIO INPUT1
OPTICAL
(COMPONENT1)

DIGITAL
AUDIO INPUT2
OPTICAL
(DVI)

DVD/DTV INPUT

P

R

COMPONENT1

(480i/480p/720p/1080i)

COMPONENT2

PB

Y

L

R

AUDIO

P

R

PB

Y

L

R

AUDIO

+75 Ω +75 Ω

Set-top Box

Set-top Box

The DTV shows the sharpest picture in 720p/1080i mode.

1920x1080i

1280x720p

720x480p

DVI

or

Component 1 (or 2) Input

Y PB PR

1920X1080i

1280X720p

720X480p

720X480i

PAGE 14

206-04007

Monitor Out Setup

Your TV has a special signal output capa­bility which allows you to hook up a sec­ond TV or monitor.

Just connect the second TV or monitor to
the Monitor output Audio/Video jacks
located on the back of your TV. See the
Operating Manual of the second TV or
monitor for further details regarding that
device’s input settings.

1

2

Audio
input

Video
input

S-Video

VIDEO

VIDEO

AUDIO

L(MONO) R

S-VIDEO VIDEO/AUDIO INPUT MONITOR OUTPUT

VARIABLE

AUDIO

IN1

IN2

IN3

R

L

R

L

AUDIO

R

L

AUDIO

A/V cables
not included
with TV

Second TV

DTV, Component 1 - 2 and DVI input sources
cannot be used for Monitor Out.

PAGE 15

206-04007

External Stereo

Locate the Variable Audio Out jacks on the
back of your TV and the Input jacks on
the back of your stereo's amplifier.

Connect the two jacks, making sure that
the right and left channels are connected
correctly.

Set up your speakers through your analog
stereo amplifier, according to the instruc­tions provided with the amplifier.

1

2

3

VIDEO

VIDEO

AUDIO

L(MONO) R

S-VIDEO VIDEO/AUDIO INPUT MONITOR OUTPUT

VARIABLE

AUDIO

IN1

IN2

IN3

R

L

AUDIO

R

L

AUDIO

A/V cables
not included
with TV

Analog stereo amplifier

Hook up Variable Audio Output, L-Audio-R to
Amplifier system for Left/Right front speaker sound.

PAGE 16

206-04007

Digital Audio Output

Connect one end of an optical cable to
the TV Digital Audio Optical Output port.

Connect the other end of the optical cable
to the digital audio optical input on the
audio equipment.

See the external audio equipment instruc­tion manual for operation.

1

2

Digital Audio
Optical Input

CALIBRATION

DIGITAL
AUDIO OUTPUT
OPTICAL

ANTENNA 1 ANTENNA 2

DVI-HDTV INPUT

DIGITAL
AUDIO INPUT1
OPTICAL
(COMPONENT1)

DIGITAL
AUDIO INPUT2
OPTICAL
(DVI)

+75 Ω +75 Ω

Send the TV’s audio out to external audio equipment (stereo system) via
the Digital Audio Output Optical port.

Caution: Do not look into the optical output
port. Looking at the laser beam may damage
your vision.

Digital Audio
Equipment

PAGE 17

206-04007

Turning the TV On

On-Screen Displays

This page describes your on-screen display and information banner options.

10

Mute

TV 2-0

MONO

10:00 AM

TV 12-0

First, connect antenna cable and power cord correctly. At this moment, the TV switches to standby mode.

In standby mode to turn TV on, press the POWER, CH UP/DOWN, TV/VIDEO, SIDE, COMP/DVI or number but­tons on the remote control or POWER, TV/VIDEO or CH UP/DOWN on the TV.

Select the viewing source by using TV/VIDEO, COMP/DVI or SIDE button on the remote control.

This TV is programmed to remember which mode it was last set to, even if you turn the TV off.
Note: See page 20 if you have not auto programmed the TV to receive channels in your local broadcast area.

When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.

1

2

3

If you will be away on vacation, disconnect the power plug from the wall power outlet.

PIP Display

This display
appears when PIP
is active.

Volume

Volume level is displayed
while adjusting the sound.

Mute

Appears when
sound is muted.

Time

Appears when pressing the
enter button on remote control.

Main Channel Display

Displays current channel number.

Main Channel
Label

Displays current
channel label.

PAGE 18

206-04007

Remote Control Functions in TV Mode

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

SURF

Use to scroll the Surf channel
list.

MENU

Brings up the main menu

to the screen.

EXIT

Clears all on-screen displays
and returns to TV viewing
from any menu.

CC

Lets you select a closed caption
mode for displaying captioning
information when provided for
DTV/Analog signal.

VIDEO

Adjusts the factory preset pic­ture according to the room.

PIPCH+

Changes to next higher PIP
channel.

PIP INPUT

Selects the input source for
the sub picture.

MUTE

Switches the sound on or off

THUMBSTICK

Allows you to navigate the on-screen

menus and to adjust the system set-

tings and preferences, by moving to

an option with

F G

and selecting the

highlighted option with .

TV/VIDEO

Selects: DTV, Analog, Video1,

Video2, Video3, Front video,

Component 1-2, and DVI input

sources.

MODE

Selects the remote operating mode:

TV, VCR, Cable, DVD or Satellite.

Select other operating modes, for

the remote to operate external

devices.

SIDE

Selects the front video input

sources.

COMP/DVI

Selects: Component 1,
Component 2, and DVI input
sources.

AUDIO

Selects MTS sound: Mono,

Stereo, and SAP.

Change the audio language

in DTV mode.

PIPCH-

Changes to next lower

PIP channel

PIP

Switches between PIP, POP

(Picture-outside-Picture) and

Twin picture mode.

LIGHT

Illuminates the remote control
buttons.

MODE INDICATOR
LIGHTS

Show active remote mode
every time any button is
pressed.

D
E

PAGE 19

206-04007

Remote Control Functions in TV Mode

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

POWER

Turns your TV or any other
programmed equipment on or
off, depending on mode.

CHANNEL UP/DOWN

Scrolls through available channels
present in EZ Scan memory.

NUMBER KEYPAD

For direct channel selection and

programming functions.

ENTER

When in the menu system and
other on-screen displays,
selects highlighted options.

RECORD, PAUSE, REW, FFWD,

PLAY, STOP

Control the functions on your VCR.

VOLUME UP/DOWN

Increases/decreases the sound level.

INFO

When you watch the TV, dis-

plays information on top of the

screen. Not available in

Component 1-2 and DVI.

SKIP LEFT/RIGHT

Playing CDs: Selects songs.
Playing DVDs: Selects movie
chapters.

RATIO

Changes the aspect ratio.

SIGNAL

Displays the digital signal strength.

DASH

Is used to enter a program num-

ber for multiple program channels

such as 2-1,2-2,etc.

FLASHBK

Tunes to the last channel
viewed.

TIMER

Lets you select the amount of

time before your TV turns

itself off automatically.

SWAP

Swaps the signal from your PIP
window to the main screen.

FREEZE

Captures and freezes the
currently-viewed picture.
Main picture is frozen in
PIP or Twin picture mode.

PAGE 20

206-04007

EZ Scan (Channel Search)

Use pages 9-16 to connect external
equipment to your TV. If you have done
so, plug in your TV to a standard 120V,
60Hz power outlet.

If you have done so, remove the back of
the remote and install in two AA batter­ies. Make sure batteries are properly
installed (check the +/– symbols).

With the remote control in hand, press
the POWER button to turn your TV on.

1

2

3

Automatically finds all channels available
through antenna or cable inputs, and
stores them in memory on the channel
list.

back of
remote

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

4

8

3

Option 1 Option 2

Option 3 Option 4

4/6/7

4/6/7

5/6

PAGE 21

206-04007

EZ Scan continued

Press the MENU button on the remote control, then
use the UP/DOWN arrow button to select the Setup
menu

Press the RIGHT arrow button to access the Setup
menu.

Use the UP/DOWN arrow button to select EZ Scan,
then press the RIGHT arrow button.

Use the UP/DOWN arrow button to select option 1,
2, 3, or 4. (Based on your connection(s) to
Antenna 1-2.)

Press ENTER button to begin the channel search.
Note: Allow EZ Scan to complete the channel
search cycle for TV, CABLE*, DTV, etc.

4

5

6

7

8

Run EZ Scan again after any
Antenna/Cable connection changes.

Mini glossary

TV The antenna device receiving the program signal sent over-the-air.

DTV Digital TV programming sent over-the-air.

CATV Your EZ Scan selection, if you subscribe to a cable service.

CADTV Your EZ Scan selection, if you subscribe to a digital cable service.

*Cable Service Band Note: Select Std=Standard, HRC=HRC Band, or IRC=IRC Band.

For further band information, contact your cable service provider.

PAGE 22

206-04007

Channel Edit

Create two different types of channel lists in memory: “Custom
list” and “Favorite channel list” from the default channel list
made in the EZ scan menu.
A custom list can be created by toggling each channel on or off
with the (Enter) key. Once a channel is highlighted, you will be
able to see whether the channel is currently added or deleted by
referring to the small window at the top-left corner of the screen.
You can create your own favorite channel list with up to 10 chan­nels. It appears at the bottom-left corner of the screen.
Use the Surf button on the remote control when a channel is high­lighted, to add or delete the channel in the favorite channel list.

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Setup menu.

Press the RIGHT arrow button to access
the Setup menu.

Use the UP/DOWN arrow button to select
Ch.Edit and then press the RIGHT arrow
button.

You will now see a screen filled with
channel numbers and a preview picture.
Use the UP/DOWN and LEFT/RIGHT arrow
button to select a channel, then use
the button to add or delete it. Press
SURF to add the channel to the Surf List.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

3

4

5

2

1

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

4

5

4

2/3/4

1/3/4

1/3/4

4

CATV is available for 1-125 channel.

PAGE 23

206-04007

DTV Signal

1

2

Press the

signal button on the remote

control.

View the on-screen signal strength moni­tor to see the quality of the signal being
received.

Press exit button to return to TV viewing.

3

Lets you know how strong your DTV signal is and whether
you need to adjust your antenna or digital cable input.
The higher the signal strength, the less likely you are to
experience degradation.

NOT all areas or programs are currently
available with Digital DTV signals.
Select the DTV in Main Input on the menu,
to check the DTV signal.

Using the signal button

1

2

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Setup menu.

Press the RIGHT arrow button to access
the Setup menu.

Use the UP/DOWN arrow to select the DTV
Signal. Current signal strength is shown
on menu.

Press EXIT button to return to TV viewing.

3

4

Using the menu

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/3

1/3

4

2

1

PAGE 24

206-04007

Channel Label Setup

Choose preset labels for your channels.

Use Channel +/- on your remote control in the Ch Label
menu to select a channel for labeling, and choose a suit­able label for your channel by pressing to set the
label to the selected channel.

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Setup menu.

Press the RIGHT arrow button to access
the Setup menu.

Use the UP/DOWN arrow button to select
ch.Label and then press the RIGHT arrow
button.

You will now see a screen filled with
Labels and a preview screen. Use channel
UP/DOWN button on your remote control
to select the a channel to Label.

Use the UP/DOWN and LEFT/RIGHT arrows
to select the appropriate label for the
channel and press to set the Label to
the selected channel.

Repeat 4 and 5 steps until all channels
are Labeled.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

3

4

5

6

7

2

1

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/7

5

7

4

2/3/5

1/3/5

1/3/5

5

The TV displays a short name for a DTV
channel even if you didn't preset a label
for the channel.

PAGE 25

206-04007

Main Picture Source Selection

1

2

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Setup menu.

Press the RIGHT arrow button to access
the Setup menu.

Use the UP/DOWN arrow to select the
Main Input option.

Press the RIGHT arrow to access the Main
Input menu, then use the UP/DOWN arrow
button to select the source. Your Main
picture source options are : DTV, Analog,
Video1, Video2, Video3, Side video,
Component1, Component2, and DVI.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

3

4

5

Note: This TV is equipped with Picture-in-Picture. Select a
viewing source for the main picture on this page and
select a viewing source for the PIP picture inset on the
following page.

Changes the picture source for the main screen so you
can watch your on-air TV, cable TV, VCR, DVD, or any
other devices that are connected to your TV.

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

2/4

5

1/3/4

1/3/4

Using the menu

1

Use the tv/video, side, and comp/dvi but­ton to select the input source.

Each time you press tv/video button, you
toggle between DTV, Analog, Video1, Video
2, Video3, Side Video, Component1,
Component 2, and DVI.
Each time you press side button, you tog­gle between connected Side Video sources.
Each time you press comp/dvi button, you
toggle between Component1, Component2,
and DVI.

Using the tv/video, side, and comp/dvi button

PAGE 26

206-04007

PIP (Picture-In-Picture) Options

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Setup menu.

Press the RIGHT arrow button to access
the Setup menu.

Use the UP/DOWN arrow to select the
Sub Input option.

Press the RIGHT arrow to access the Sub
Input menu, then use the UP/DOWN arrow
button to select the source. Your choices
are: DTV, Analog, Video1, Video2, Video3,
and Side Video.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

1

2

3

4

5

Changes the picture source for the Picture-In-Picture
screen so you can watch your on-air TV, cable TV, VCR,
or any other devices that are connected to your TV.

Press the PIP button to show the sub picture.
Each press of PIP changes the PIP options as shown below.

PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other
source will show a smaller inset image.

Use the PIP INPUT button to select the
input source for the sub picture.
Each time you press PIP INPUT button,
you toggle between DTV, Analog, Video1,
Video2, Video3, and Side Video.

Do not display a fixed image on the screen for long
periods of time.

Component 1-2 and DVI input sources are not avail­able for PIP/Twin picture input source.

You can’t select DTV for main and sub picture simul­taneously.

Using the menu

Using the PIP INPUT button

PIP mode POP mode

PIP off

Twin Picture mode

Watching PIP

PIP Source Selection

PAGE 27

206-04007

PIP (Picture-In-Picture) Options

1

2

Press the SWAP button.
Each time you press the SWAP button, you switch the Main and PIP pictures.

Press the PIP button.

Select the Analog or DTV option on the Sub input menu or with the PIP INPUT button. Use
the PIPCH-/PIPCH+ button to select a channel for the sub picture.

Main Picture Sub Picture

Selecting PIP Channels

Swapping Screen

In the PIP mode, each press of the UP/DOWN/LEFT/RIGHT arrow button will
move the sub picture to a different position on the screen.

Moving the Sub Picture

PAGE 28

206-04007

Press PIP on the remote control with the
POP image on the screen to activate POP
(Picture-outside-Picture) mode.
The pictures of all the programmed chan­nels are searched with the 3 POP screen,
as shown to the right.

• Channel selection: Press LEFT arrow but­ton to enlarge the selected channel
being searched on the POP screen to
view it on the Main screen.

• POP selection: Use UP/DOWN arrow but­ton to select one of 3 POP screen pic­tures in POP mode.

• Input source selection for POP: Use PIP
INPUT button or Sub input of Setup
menu to select input souce for sub pic­ture (You can’t select DTV for main and
sub picture simultaneously).

Press the EXIT button to exit POP mode.

1

In DTV 720p/1080i mode, press the FREEZE
button.

Use UP/DOWN/LEFT/RIGHT arrow button to
select the screen split zoom section.

Press the FREEZE/RATIO or EXIT button to
return to TV viewing .

1

2

3

2

Use POP to search the pictures of all the programmed chan­nels one-by-one on the 3 POP screen display, while the main
screen remains the current channel.

Run EZ Scan channel search before using
POP mode.

F TV 13-0

EE

DD

TV 51-0

TV 63-0

Multi Point Zooming

POP (Picture-Outside-Picture) Source

PAGE 29

206-04007

Twin Picture

Twin Picture splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same
time. Each source is given half the screen.

Use the PIP INPUT button to select the input source for the sub picture.
Each time you press PIP INPUT, you toggle between DTV, Analog, Video1,
Video2, Video3, and Side Video.

1

2

Press the SWAP button.
Each time you press SWAP, you switch the Main and Sub pictures.

Press the PIP button on the remote control in POP mode to activate twin picture mode.
Select the Analog or DTV option on the Sub input menu or with the PIP INPUT button.
Use the PIPCH-/PIPCH+ button to select a channel for the sub picture.

Press the EXIT button to exit twin picture mode.

Main Picture Sub Picture

Watching Twin Picture

Swapping Screen

Selecting an Input Signal Source for Sub Picture

Use the UP/DOWN/LEFT/RIGHT arrow button to adjust main and sub picture
size in twin Picture mode.

Adjusting Picture Size

PAGE 30

206-04007

VIDEO Menu

Use the VIDEO button to select EZ Picture option.

Each press of the VIDEO button change the EZ
Picture option: Off, Normal, Digital Preset, Night
Time, Movie, Weak Signal, Video Game, and
Sports.

Press EXIT to save and return to TV viewing.

1

2

This function adjusts the TV to the best picture appear­ance. Select the preset value in the EZ Picture menu
based on the program category.
Digital Preset, Night Time, Movie, Weak Signal, Video
Game, and Sports are preset for good picture quality at
the factory and cannot be changed.
When adjusting video options (Contrast, Brightness, Color,
Sharpness, and Tint) manually, EZ Picture automatically
changes to ‘Off’.

EZ Picture

Choose the Normal option to reset the EZ picture
options to their factory preset values, or use your
own settings with Off.

Using the VIDEO button

1

2

Press the MENU button on the remote control,
then use the UP/DOWN arrow button to select
the Video menu.

Press the RIGHT arrow button to access the Video
menu.

Use the UP/DOWN arrows to select the EZ Picture
option.

Press the RIGHT arrow to access the EZ Picture
menu, then use the UP/DOWN arrow button to
select the options: Off, Normal, Digital Preset,
Night Time, Movie, Weak Signal, Video Game, and
Sports.

• Off: Allows you to adjust the picture the way
you want.

• Normal: Resets all the options to their preset
values.

• Other options adjust the picture to the source’s
image.

Press EXIT button to return to TV viewing or press
MENU button to return to the previous menu.

3

4

5

Using the menu

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

2/4

5

1/3/4

1/3/4

Each video menu adjustment doesn’t effect other input
sources. Readjust Video menu for each input source.

PAGE 31

206-04007

VIDEO Menu

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Video menu.

Press the RIGHT arrow button to access
the Video menu.

Use the UP/DOWN arrow button to select
one of the following options: Contrast,
Brightness, Color, Sharpness, or Tint, then
press the RIGHT arrow button.

• Contrast: Adjusts the difference
between the light and dark levels of
the picture.

• Brightness: Adjusts the white or light
level of the overall picture.

• Color: Adjusts the intensity of all col-
ors.

• Sharpness: Adjusts the level of crisp-
ness in the edges between the light
and dark areas of the picture. The lower
the level, the softer the image.

• Tint: Adjusts the balance between the
red and green levels.

Use the LEFT/RIGHT arrow button to
adjust the option to your preference. Use
the UP/DOWN arrow button to select
another option.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

You can manually adjust the levels of picture quality settings,
such as Contrast, Brightness, Sharpness, etc.

Adjust the picture appearance to suit your preference and
viewing situations.

4

5

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

4

5

2/3/4

1/3/4

1/3/4

Manual Video Control

PAGE 32

206-04007

VIDEO Menu

Press the MENU button on the remote control, then use
the UP/DOWN arrow button to select the Video menu.

Press the RIGHT arrow button to access the Video
menu.

Use the UP/DOWN arrow button to select Video Preset.

Use the RIGHT arrow button to preset the video config­uration.

1

2

3

This is the function to quickly reset every Video menu
option to their factory preset values.

4

Video Preset

Press the MENU button on the remote control, then use
the UP/DOWN arrow button to select the Video menu.

Press the RIGHT arrow button to access the Video
menu.

Use the UP/DOWN arrow button to select Z-View, and
then press the RIGHT arrow button.

Use the UP/DOWN arrow button to select Off or On.

Press EXIT button to return to TV viewing or press
MENU button to return to the previous menu.

1

2

3

4

5

Z-View

Press the MENU button on the remote control, then use
the UP/DOWN arrow button to select the Video menu.

Press the RIGHT arrow button to access the Video
menu.

Use the UP/DOWN arrow button to select Color
Temperature, and then press the RIGHT arrow button.

Use the UP/DOWN arrow button to select Warm,
Medium, or Cool.

Press EXIT button to return to TV viewing or press
MENU button to return to the previous menu.

1

2

3

Lets you choose one of three automatic color adjustments. Set this to warm for hotter colors such as red, or set to cool for less intense
colors with more blue.

4

5

Color Temperature

When This function is to On, automatically adjusts the
picture display for optimum quality.

PAGE 33

206-04007

AUDIO Menu

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Audio menu.

Press the RIGHT arrow button to access
the Audio menu.

Use the UP/DOWN arrow button to select
Audio Language, then press the RIGHT
arrow button.

Use the UP/DOWN arrow button to select
the language you wish.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

Other languages may be available only if a digital signal is being sent by the broadcasting station.

4

5

Audio Language

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Audio menu.

Press the RIGHT arrow button to access
the Audio menu.

Use the UP/DOWN arrow button to select
EZ SoundRite, then press the RIGHT arrow
button.

Use the UP/DOWN arrow button to select
On or Off.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

Scans for changes in sound level during commercials, then adjusts the sound to match the current audio level. This will make sure
that the volume level will be consistent whether you are watching a commercial or a regular TV program.

4

5

EZ SoundRite

PAGE 34

206-04007

AUDIO Menu

1

2

This function lets you enjoy the best sound without any special
adjustment because the TV automatically selects the appropriate
sound option based on the program content.
Stadium, News, Music and Theater are preset for good sound quali­ty at the factory and cannot be changed.
When adjusting audio options (treble and bass) manually, EZ
Sound automatically changes to Off.

This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo
program; if the station transmits an additional sound signal as well as the original one.

Use the AUDIO button on the remote control to select your desired MTS mode. Each
time you press the AUDIO button, MONO, STEREO, or SAP appear in turn.

Press EXIT to save and return to TV viewing.

EZ Sound

Stereo/SAP Broadcasts Setup

Choose the NORMAL option in EZ Sound to quickly
reset the Audio Menu options to their original pre­set values, or use your own settings with Off.

Stereo or SAP can be received only when the TV station transmits those signals even
though you have selected STEREO or SAP.

Mono sound is automatically received if the broadcast is only in Mono; even though
STEREO or SAP has been selected.

Select MONO if you want to listen to the mono sound in remote fringe areas during
stereo/SAP broadcasting.

1

2

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Audio menu.

Press the RIGHT arrow button to access
the Audio menu.

Use the UP/DOWN arrow to select the EZ
Sound option.

Press the RIGHT arrow to access the EZ
Sound menu, then use the UP/DOWN
arrow button to select the options: Off,
Normal, Stadium, News, Music and
Theater.

• Off: Allows you to adjust the picture
the way you want.

• Normal: Resets all the options to their
preset values.

• Other options adjust the TV's audio out­put to the source’s sound.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

3

4

5

PAGE 35

206-04007

AUDIO Menu

Press the MENU button on the remote control, then use
the UP/DOWN arrow button to select the Audio menu.

Press the RIGHT arrow button to access the Audio
menu.

Use the UP/DOWN arrow button to select one of the
following options: Balance, Treble, or Bass, then press
the Right arrow button.

• Balance: Lets you adjust the left to right balance of
the TV speakers.

• Treble: Increases or decreases the higher frequency
sounds from the TV speakers.

• Bass: Increases or decreases the lower frequency
sounds from the TV speakers.

Use the LEFT/RIGHT arrow button to adjust the option
to your preference. Use the UP/DOWN arrow to select
another option.

Press EXIT button to return to TV viewing or press
MENU button to return to the previous menu.

1

2

3

Adjust the sound to suit your taste and room situations.

Turns the TV Speaker option On or Off.

4

5

Manual Sound Control

Turn TV Speakers On/Off

1

2

Press the MENU button on the remote control, then use
the UP/DOWN arrow button to select the Audio menu.

Press the RIGHT arrow button to access the Audio
menu.

Use the UP/DOWN arrow button to select TV Speaker,
then press the RIGHT arrow button.

Use the UP/DOWN arrow button to select On or Off.

Press EXIT button to return to TV viewing or press
MENU button to return to the previous menu.

3

4

5

PAGE 36

206-04007

AUDIO Menu

Front Surround

1

2

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Audio menu.

Press the RIGHT arrow button to access
the Audio menu.

Use the UP/DOWN arrow button to select
Front Surround, then press the RIGHT
arrow button.

Use the UP/DOWN arrow button to select
Off, 3D EchoSound System or SRS (Sound
Retrieval System) TruSurround XT.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

3

4

5

is a trademark of SRS Labs, Inc.

TruSurround XT technology is incorporated under license
from SRS Labs, Inc.

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

2/3

5

1/3/4

1/3/4

Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.

Mini glossary

SRS TruSurround XT

Takes advantage of any multi-channel format
without needing to add extra speakers or equip­ment. Dialog clarity, bass enrichment and the
addition of stereo audio enhancement that pro­duces an immersive sound experience from stan­dard stereo material.

3D EchoSound System

Creates a stunning simulated stereo effects from
any mono sound and a realistic three-dimensional
sound with a very wide and deep sound stage
into stereo sound.

PAGE 37

206-04007

Auto Clock Setup

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Time menu option.

Press the RIGHT arrow button to go to
the Time menu.

Use the UP/DOWN arrow button to choose
Auto Clock, then press the RIGHT arrow
button.

Use the UP/DOWN arrow button to choose
On, then use the RIGHT arrow button to
select Time Zone.

Use the UP/DOWN arrow button to adjust
Time Zone.

• Select the time zone for your viewing
area. Your options are: Eastern,
Central, Mountain, Pacific, Alaska,
Hawaii.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

5

6

Sets the time automatically through the digital channel
signal.

The digital channel signal includes information for the
current time provided by the broadcasting station.

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/6

6

2/3/4

1/3/4/5

1/3/4/5

Set the clock manually again if the
current time is incorrect with auto
clock function.

PAGE 38

206-04007

Manual Clock Setup

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Time menu option.

Press the RIGHT arrow button to activate
the Time menu.

Use the UP/DOWN arrow button to choose
Manual Clock, then press the RIGHT arrow
button.

Use the LEFT/RIGHT arrow button to
select either the year, hour or minutes
option. Once selected, use the UP/DOWN
arrow button to set the year, hours or
minutes.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

5

If current time setting is erased by a power failure or if
TV is unplugged, reset the clock.

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

5

2/3/4

1/3/4

1/3/4

4

PAGE 39

206-04007

TV Turn Off Time Setup

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Time menu.

Press the RIGHT arrow button to to go to
the Time menu.

Use the UP/DOWN arrow button to choose
Off Timer, then press the RIGHT.

Use the UP/DOWN arrow button to choose
On, then press the RIGHT arrow button.

Use the LEFT/RIGHT arrow button to
select the hour or minutes options, then
use the UP/DOWN arrow button to set the
hours or minutes.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

5

Lets you set an automatic daily turn off time for your TV.

Off Timer function overrides On Timer function if they are
both set to the same time.

You must set the current time on the clock before using
on/off timers.

6

Next G

To cancel Off Timer function, use the
UP/DOWN arrow button to select Off in
step 4.

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/6

5

6

1/3/4/5

2/3/4/5

1/3/4/5

PAGE 40

206-04007

TV Turn On Time Setup

Lets you set an automatic daily turn on time for your TV.

Off timer function overrides on timer function if they are
both set to the same time.

Unless a button is pressed within two hours after the TV
is turned on by the On Timer function, the TV will auto­matically turn off.

TV must be in standby mode for the On Timer to work.

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Time menu.

Press the RIGHT arrow button to activate
the Time menu.

Use the UP/DOWN arrow button to choose
On Timer, then press the RIGHT arrow
button.

Use the UP/DOWN arrow to choose On,
then press the RIGHT arrow button.

Use the LEFT/RIGHT arrow button to
select either Time, Channel, or Volume.
Once selected, use the UP/DOWN arrow
button to set either the Time, Channel, or
Volume options.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

5

6

To cancel On Timer function, use the
UP/DOWN arrow button to select Off in
step 4.

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/6

5

6

1/3/4/5

2/3/4/5

1/3/4/5

PAGE 41

206-04007

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Time menu.

Press the RIGHT arrow button to go to
the Time menu.

Use the UP/DOWN arrow button to choose
Sleep Timer then press the RIGHT arrow
button.

Use the UP/DOWN arrow to choose a pre­set turn off time.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

5

Sleep Timer Setup

Press the TIMER button on the remote
control repeatedly to select the number of
minutes.

First the Off option will appear on the
screen, followed in sequence 10, 20, 30,
60, 90, 120, 180, and 240. The timer
begins to count down from the number of
minutes selected.

Press EXIT button to save and return to
TV viewing

1

2

Lets you select the amount of time if you want your TV to
turns itself off, automatically.

When the sleep time you want is displayed
on the screen, don’t press the timer button
again.

To check the remaining sleep time, press
the timer button once.

To change sleep time setting, press the
timer button repeatedly to select time set­ting you want.

If you turn the TV off after setting the
sleep timer, the setting will be erased.

Using the timer button

Using the menu

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

2/3

5

1/3/4

1/3/4

PAGE 42

206-04007

Auto Off

If there is no input signal, the TV can be set up to switch
to standby mode automatically after 10 minutes.

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Time menu.

Press the RIGHT arrow button to go to
the Time menu.

Use the UP/DOWN arrow button to choose
Auto Off then press the RIGHT arrow.

Use the UP/DOWN arrows to choose On or
Off.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

5

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

2/3

5

1/3/4

1/3/4

PAGE 43

206-04007

Aspect Ratio Control

Press the MENU button on the remote control, then use
the UP/DOWN arrow button to select the Option menu.

Press the RIGHT arrow button to go to the Option
menu.

Use the UP/DOWN arrow to choose the Aspect Ratio
option, then press the RIGHT arrow button.

Use the UP/DOWN arrow button to select the desired
picture format.

• Use the UP/DOWN arrow button to adjust the

enlarge proportion of Cinema Zoom. The adjustment
of range is 1~16.

Press EXIT button to return to TV viewing or press
MENU button to return to the previous menu.

1

2

3

4

5

Use the RATIO button to select the desired picture for­mat.

Each press of the RATIO button changes the picture for­mat. Your options are: Set By Program, 4:3, 16:9,
Horizon, Zoom1, Zoom2, and Cinema Zoom.

Press EXIT to save and return to TV viewing.

1

2

Lets you choose the way that an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio.
When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to
be displayed according to your preference.

Using the RATIO button

Using the menu

Mini glossary

Set By Program Select the proper picture proportion to match the source’s image. (4:3 → 4:3, 16:9 → 16:9)

4:3 Choose when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right

sides.

16:9 Choose when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

Horizon Choose when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacu-

lar view.

Zoom1 Choose when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be

cropped.

Zoom2 Choose when you want the picture to be altered, both vertically extended and vertically cropped. The picture taking a halfway

trade off between alteration and screen coverage.

Cinema Zoom Choose when you want to enlarge the picture in correct proportion. When enlarging or reducing the picture, the image may

become distorted.

When you receive a picture with a 16:9 aspect ratio, you
can’t specify horizon aspect ratio.

If you select a horizon during receiving a 4:3 aspect
ratio, 16:9 aspect ratio is worked as set by program.

PAGE 44

206-04007

Closed Captions

1

2

1

2

3

4

5

Mini glossary

CAPTIONS The term for the words that scroll across the bot-

tom of the TV screen; usually the audio portion of
the program provided for the hearing impaired.

TEXT The term for the words that appear in a large

black frame and almost cover the entire screen;
usually messages provided by the broadcaster.

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

2/3

5

1/3/4

1/3/4

Select a caption mode for displaying captioning informa­tion when provided on the program.

Analog caption displays information at any position on
the screen usually the program's dialog.
Text displays information, usually at the bottom position
and is used for a data service, generally not program
related.

Caption/Text, if provided by the broadcaster, would be
available for both digital and analog channels on the
Antenna 1 source.

Use the CC button to select caption.

Each press of the CC button changes the caption
option; Off, CC1, CC 2, CC 3, CC 4, Text 1, Text 2,
Text 3, or Text 4.

Press EXIT to save and return to TV viewing.

Press the MENU button on the remote control, then
use the UP/DOWN arrow button to select the Option
menu.

Press the RIGHT arrow button to activate the Option
menu.

Use the UP/DOWN arrow button to choose Caption,
then press the Right arrow button.

Use the UP/DOWN arrow button to make your caption
selection. Your choices are: Off, CC1, CC 2, CC 3, CC 4,
Text 1, Text 2, Text 3, or Text 4.

Press EXIT button to return to TV viewing or press
MENU button to return to the previous menu.

Using the CC button

Using the menu

This TV is programmed to remember the caption/text
mode it was last set to, when you turn the POWER off.

PAGE 45

206-04007

Closed Captions (Continued)

1

2

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Option menu.

Press the RIGHT arrow button to access
the Option menu.

Use the UP/DOWN arrow to select the
Caption, then press the RIGHT arrow but­ton.

Use the UP/DOWN arrow button to choose
any of the following options : Off,
English, Spanish, or French.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

Press the CC button repeatedly to scroll
and select available caption languages.

Press EXIT to save and return to TV view­ing.

3

4

5

Choose the language you want the DTV/CADTV Captions
to appear in.

Languages can be chosen for digital sources only if they
are included on the program.

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

2/3

5

1/3/4

1/3/4

Using the CC button

Using the menu

PAGE 46

206-04007

Caption Option Menu

6

Customize the DTV/CADTV captions that will
appear on your screen.

1

2

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Option menu.

Press the RIGHT arrow button to access
the Option menu.

Use the UP/DOWN arrow to select the
Caption Option, then press the RIGHT
arrow button.

Use the LEFT/RIGHT arrow button to
select Custom.

Use UP/DOWN arrow button to customize
the Style, Font, etc., to your preference.
Your Caption options are:

• Size: Set the size the words will appear

in.

• Font: Select a typeface for the words.

• Text Color: Choose a color for the text.

• Text Opacity: Specify the opacity for

the text color.

• Bg (Background) Color: Select a back-

ground color.

• Bg (Background) Opacity: Select the

opacity for the background color.

• Edge Type: Select an edge type.

• Edge Color: Select a color for the

edges.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

3

4

5

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/5

5

4

1/3/4
2/3/4

1/3/4

A preview icon is provided at the bottom
of the screen, use it to see the caption
language.

PAGE 47

206-04007

Velocity Modulation

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Option menu.

Press the RIGHT arrow button to access
the Option menu.

Use the UP/DOWN arrow button to select
VM, and then press the RIGHT arrow but­ton.

Use the UP/DOWN arrow button to select
Off, Low, or High.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

5

On-Screen Menu Languages

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Option menu.

Press the RIGHT arrow button to go to
the Option menu.

Use the UP/DOWN arrow to choose the
Language, then press the RIGHT arrow
button.

Use the UP/DOWN arrow button to select
the language you want the on screen
menus to appear in.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

5

Select your preferred language for the menus: English,
Español (Spanish), or Français (French).

Use this function to improve the outline distinction of
the picture's edges.

If you select VM ‘Off’, the TV will automatically return
the pictures' edge appearance to factory settings.

PAGE 48

206-04007

Tilt

Degaussing the Screen

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Option menu.

Press the RIGHT arrow button to access
the Option menu.

Use the UP/DOWN arrow button to select
Tilt, then, use the LEFT/RIGHT arrow but­ton to adjust and correct any Tilt.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

The picture on the TV screen may be tilted to the left
or right if the set is moved to a different place or
direction. Picture Tilt should be used to correct any
tilt.

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Option menu.

Press the RIGHT arrow button to access
the Option menu.

Use the UP/DOWN arrow button to select
Degauss, then press the RIGHT arrow
button to perform the Degauss function.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

The magnetic field of the earth may affect the color puri­ty of the picture and other magnetic influences nearby
may also have an affect on color purity. Even the installa­tion direction of the TV set may affect color purity.
Stripes may appear on the screen or the color may not be
equal in the corners. You can restore color quality by
operating the Degauss.

If you are unable to correct problem by degaussing,
try again after about 4 minutes.

PAGE 49

206-04007

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Option menu.

Press the RIGHT arrow button to access
the Option menu.

Use the UP/DOWN arrow to choose
Cinema, then press the Right arrow but­ton.

Use the UP/DOWN arrow to choose On or
Off.

Press EXIT button to return to TV viewing
or press MENU button to return to the
previous menu.

1

2

3

4

Cinema Mode Setup

Set up the TV for the best picture appearance for viewing
movies.

5

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

2/3

1/5

5

1/3/4

1/3/4

PAGE 50

206-04007

EZ Demo

Press the MENU button on the remote
control, then use the UP/DOWN arrow
button to select the Option menu.

Press the RIGHT arrow button to access
the Option menu.

Use the UP/DOWN arrow button to select
EZ Demo, then press the RIGHT arrow
button.

Press EXIT button on the remote to stop
EZ Demo.

1

2

3

4

Shows you how to navigate the TV's on-screen menus.

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/3

2/3

1/3

1

4

PAGE 51

206-04007

Parental Lock Setup

Press the MENU button on the remote control,
then use the UP/DOWN arrow button to select
the Lock Menu option.

Press the RIGHT arrow button to activate the
Lock Menu.

Use the UP/DOWN arrow to choose from the
following Lock Menu options. Once the options
are selected, change the settings to your pref­erences.

•

Lock System: Activates or disables the blocking
scheme you set up previously.

• Set Password: Change the password by inputting

a new password twice.

• Block Ch.: Blocks any channels that you do not

want to watch or that you do not want your chil­dren to watch.

• Movie Rating (MPPA): Blocks movies according

to the movie ratings limits specified, so children
cannot view certain movies. You can set the rat­ings limit by blocking out all the movies with the
ratings above a specified level. Keep in mind that
the movie ratings limit only applies to movies
shown on TV, not TV programs, such as soap
operas.

• TV Rating-Children: Keeps children from watch-

ing certain TV programs among only the programs
intended for children, according to the ratings
limit. The children rating does not apply to other
TV programs. Unless you block certain TV pro­grams intended for mature audiences in the TV
Rating - sub menu, your children can view those
programs.

• TV Rating-General: Blocks certain TV programs

that you and your family do not want to view,
based on the ratings.

• Aux. Block: Enables you to select a source for

blocking among the source devices you have
hooked up.

Press EXIT button to return to TV viewing or
press MENU button to return to the previous
menu.

1

2

3

4

Lets you set up blocking schemes to block specific chan­nels, ratings, and viewing sources.

A password is required to gain access to this menu if the
Lock System is activated.

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

1/3

1/4

1/3

4

2

PAGE 52

206-04007

TV-Y (All Children): Program is appropriate for all children.

TV-Y7 (Directed toward Older Children): Program is designed for children age 7 and above.

TV-G (General audience): Most parents would find this program suitable for all ages.

TV-PG (Parental guidance suggested): Program contains material that parents may find unsuitable for younger children.

TV-14 (Parents strongly cautioned): Program contains some material that many parents would find unsuitable for chil-

dren under 14 years of age.

TV-MA (Mature audience only): Program is specifically designed to be viewed by adults and therefore may be unsuitable
for children under 17.

G (General audiences): All ages can view these programs.

PG (Parental guidance suggested): Some program content may not be suitable for children.

PG-13 (Parents strongly cautioned): Some program content may not be appropriate for children under 13.

R (Restricted): Children under 17 requires parent or adult guardian to be present.

NC-17: No one 17 should be allowed to view the program.

X: For Adult viewing only.

Blocking Off: Permits all programs.

Parental Lock Rating Descriptions

Parental Lock Setup (Continued)

PAGE 53

206-04007

Programming the Remote

Test your remote control.
To find out whether your remote control can
operate the component without program­ming, turn on the component such as a VCR
and press the corresponding mode button
(VCR) on the remote control, while pointing
at the component. Test the POWER and CH
+/- buttons to see if the component
responds properly. If not, the remote
requires programming to operate the device.

Turn on the component to be programmed,
then press the corresponding mode button
on the remote control.

Press the POWER and MUTE buttons simulta­neously, the remote control is ready to be
programmed for the code.

There are two ways to find the right code for
the component.

A. If you press the CH +/- buttons repeat­edly, the codes will change one at-a-time.
Press the POWER button after each code
change. If the right code is found, the
device will turn off.

B. Enter a code number using the number
buttons on the remote. Programming code
numbers for the corresponding component
can be found on the following pages.
Again, if the code is correct, the device will
turn off.

Press the EXIT button to store the code.

Test the remote control functions to see if
the component responds properly. If not,
repeat from step 2.

1

1 2 3

4 5 6

7 8 9

0

tv

mode

light

power

tv/video

comp/dvi

freeze

vcr

cable

dvd

sat

mute

pip inputpipch- pipch+

pip

info

recordstop

pause

rew

play

ff

menu exit

timer cc

swap

vol

ch

surf

audio

video

signalratio

side

skip

dash(-) flashbk

2

3

4

5

2

3

4

5

6

4

The remote control for your HD receiver is a
multi-brand or universal remote control. It can
be programmed to operate most remote-con­trollable devices of other manufacturers.

Note that the remote control may not control
all models of other brands.

3/4

PAGE 54

206-04007

Programming Codes

VCRs

Brand Codes

AIWA 034
AKAI 016 043 046

124 125 146
AMPRO 072
ANAM 031 033 103
AUDIO DYNAMICS 012 023 039

043
BROKSONIC 035 037 129
CANON 028 031 033
CAPEHART 108
CRAIG 003 040 135
CURTIS MATHES 031 033 041
DAEWOO 005 007 010

064 065 108

110 111 112

116 117 119
DAYTRON 108
DBX 012 023 039

043
DYNATECH 034 053
ELECTROHOME 059
EMERSON 006 017 025

027 029 031

034 035 036

037 046 101

129 131 138

153
FISHER 003 008 009

010
FUNAI 034
GE 031 033 063

072 107 109

144 147
GO VIDEO 132 136
GOLDSTAR 012 013 020

101 106 114

123
HARMAN KARDON 012 045
HITACHI 004 018 026

034 043 063

137 150
INSTANTREPLAY 031 033
JCL 031 033
JCPENNY 012 013 015

033 040 066

101
JENSEN 043
JVC 012 031 033

043 048 050

Brand Codes

055 060 130
150 152

KENWOOD 014 034 039

043 047 048
LG 255
LLOYD 034
LXI 003 009 013

014 017 034

101 106
MAGIN 040
MAGNAVOX 031 033 034

041 067 068
MARANTZ 012 031 033

067 069
MARTA 101
MATSUI 027 030
MEI 031 033
MEMOREX 003 010 014

031 033 034

053 072 101

102 134 139
MGA 045 046 059
MINOLTA 013 020
MITSUBISHI 013 020 045

046 049 051

059 061 151
MTC 034 040
MULTITECH 024 034
NEC 012 023 039

043 048
NORDMENDE 043
OPTONICA 053 054
PANASONIC 066 070 074

083 133 140

145
PENTAX 013 020 031

033 063
PHILCO 031 034 067
PHILIPS 031 033 034

054 067 071

101
PILOT 101
PIONEER 013 021 048
PORTLAND 108
PULSAR 072
QUARTZ 011 014
QUASAR 033 066 075

145
RCA 013 020 033

Brand Codes

034 040 041
062 063 107
109 140 144
145 147

REALISTIC 003 008 010

014 031 033
034 040 053

054 101
RICO 058
RUNCO 148
SALORA 014
SAMSUNG 032 040 102

104 105 107

109 112 113

115 120 122

125
SANSUI 022 043 048

135
SANYO 003 007 010

014 102 134
SCOTT 017 037 112

129 131
SEARS 003 008 009

010 013 014

017 020 031

042 073 081

101
SHARP 031 054 149
SHINTOM 024
SONY 003 009 031

052 056 057

058 076 077

078 149
SOUNDESIGN 034
STS 013
SYLVANIA 031 033 034

059 067
SYMPHONIC 034
TANDY 010 034
TATUNG 039 043
TEAC 034 039 043
TECHNICS 031 033 070
TEKNIKA 019 031 033

034 101
THOMAS 034
TMK 006
TOSHIBA 008 013 042

047 059 082

112 131

Brands Codes

TOTEVISION 040 101
UNITECH 040
VECTOR RESEARCH 012
VICTOR 048
VIDEO CONCEPTS 012 034 046
VIDEOSONIC 040
WARDS 003 013 017

024 031 033
034 040 053
054 131

YAMAHA 012 034 039

043

ZENITH 001 034 048

056 058 072
080 101

PAGE 55

206-04007

SAT

DVD

Brand Codes

ALPHASTAR DSR 123
AMPLICA 050
BIRDVIEW 051 126 129
BSR 053
CAPETRONICS 053
CHANNEL MASTER 013 014 015

018 036 055

CHAPARRAL 008 009 012

077
CITOH 054
CURTIS MATHES 050 145
DRAKE 005 006 007

010 011 052

112 116 141
DX ANTENNA 024 046 056

076
ECHOSTAR 038 040 057

058 093 094

095 096 097

098 099 100

122
ELECTRO HOME 089
EUROPLUS 114
FUJITSU 017 021 022

Brand Codes

027 133 134

GENERAL INSTRUMENT 003 004 016

029 031 059

101
HITACHI 139 140
HOUSTON TRACKER 033 037 039

051 057 104
HUGHES 068
HYTEK 053
JANIEL 060 147
JERROLD 061
KATHREIN 108
LEGEND 057
LG 255
LUTRON 132
LUXOR 062 144
MACOM 010 059 063

064 065
MEMOREX 057
NEXTWAVE 028 124 125
NORSAT 069 070
PACE SKY SATELLITE 143
PANASONIC 060 142
PANSAT 121

Brand Codes

PERSONAL CABLE 117
PHILIPS 071
PICO 105
PRESIDENT 019 102
PRIMESTAR 030 110 111
PROSAT 072
RCA 066 106
REALISTIC 043 074
SAMSUNG 123
SATELLITE SERVICE CO 028 035 047

057 085
SCIENTIFIC ATLANTA 032 138
SONY 103
STARCAST 041
SUPER GUIDE 020 124 125
TEECOM 023 026 075

087 088 090

107 130 137
TOSHIBA 002 127
UNIDEN 016 025 042

043 044 045

048 049 078

079 080 086

101 135 136

Brand Codes

VIEWSTAR 115
WINEGARD 128 146
ZENITH 001 081 082

083 084 091
120

Brand Codes

APEX DIGITAL 022
DENON 020 014
GE 005 006
GOLDSTAR 010 016 025
HARMAN KARDON 027
JVC 012
LG 001 010 016

Brand Codes

025
MAGNAVOX 013
MARANTZ 024
MITSUBISHI 002
NAD 023
ONKYO 008 017
PANASONIC 003 009

Brand Codes

PHILIPS 013
PIONEER 004 026
PROCEED 021
PROSCAN 005 006
RCA 005 006
SAMSUNG 011 015
SONY 007

Brand Codes

THOMPSON 005 006
TOSHIBA 019 008
YAMAHA 009 018
ZENITH 010 016 025

Programming Codes

PAGE 56

206-04007

Programming Codes

CATV

Brand Codes

ABC 003 004 039

042 046 052

053
ANTRONIK 014
ARCHER 005 007 014

024
CABLE STAR 026
CENTURION 092
CENTURY 007
CITIZEN 007
COLOUR VOICE 065 090
COMBANO 080 081
COMTRONICS 019 030
DIAMOND 023
EAGLE 020 030 040
EASTERN 057 062 066
ELECTRICORD 032
GE 072
GEMINI 008 022 025

054
GI 052 074
GOLDEN CHANNEL 030
HAMLIN 049 050 055
HITACHI 052 055
HOSPITALITY 070 077
JERROLD 002 003 004

Brand Codes

008 009 010

052 069 074
LG 255
M-NET 037
MACOM 033
MAGNAVOX 010 012 064

079
MEMOREX 001
MOVIE TIME 028 032
NSC 015 028 038

071 073
OAK 016 031 037

053
PANASONIC 044 047
PARAGON 001
PHILIPS 006 012 013

020 065 085

090
PIONEER 034 051 052

063 076
POST NEWS WEEK 016
PRUCER 059
PTS 011 048 071

072 073 074
PULSAR 001
RCA 047

Brand Codes

REGAL 049 050
REGENCY 057
REMBRANT 025
RK 091
SAMSUNG 030 068
SCIENTIFIC ATLANTA 003 011 041

042 043 045

046
SHERITECH 022
SIGNAL 030
SIGNATURE 052
SL MARX 030
SPRUCER 047 078
STARCOM 002 004 008

009
STARGATE 008 030
SYLVANIA 067
TADIRAN 030
TANDY 017
TEXSCAN 029 067
TOCOM 039 040 056
TOSHIBA 001
UNIKA 007 014 024
UNITED CABLE 004 053
UNIVERSAL 005 007 014

024 026 027

Brand Codes

032 035

VIEWSTAR 012 015 018

086 087 088
089

ZENITH 001 060 093

PAGE 57

206-04007

1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of
lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s
almost dry, and then use it to wipe the screen.

2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

1. Use a soft cloth with a mild soap solution to wipe the cabinet.

2. Rinse the cloth and wipe the cabinet again.

3. Let the cabinet air-dry before turning the TV on.

If you expect to leave your TV dormant for a long time (such as a vacation), unplug the power cord
from the wall power outlet to protect against possible damage from lightning or power surges. If you
use an off-air antenna, you may also want to disconnect it from the back of your TV before leaving.

SCREEN CLEANING

EXTENDED ABSENCE

CABINET CLEANING

Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will
have your new TV. Be sure to turn the power off and pull out the power cord before you begin any cleaning.

Maintenance

PAGE 58

206-04007

Maintenance (Continued)

Even though you may be getting cable, the signal may be weak, which means the quality
of your picture may suffer due to other factors. If there are problems with the image on your TV,
consult the Troubleshooting guide on the following pages. You may also want to contact your cable
service provider to determine if the problem is from the cable service.

If you use your TV to play video games or for other uses that involve single, fixed images, such as
a photo-CD player, you should avoid setting the Brightness level too high.
If static images, like network identification icons or patterns, are left on the screen for a long time
period, they may leave a permanent impression on the TV screen. You can reduce the chance of
this happening by
limiting the amount of time you use the fixed-image display, and by reducing the contrast and
brightness levels.

VIDEO GAMES AND OTHER FIXED-PATTERN DISPLAYS

PICTURE INTERFERENCE

If you unplug your TV, you may have to reset the clock using the Time menu described earlier.

PAGE 59

206-04007

SYMPTOM

Snowy picture and unclear sound.

Multiple images or ‘ghost shadows.’

Interference: Sharp lines across
the screen and unclear sound.

Normal picture but no sound.

No picture and unclear sound.

No picture or sound.

No color, but the sound is okay.

Picture has a big black box
on it, but the sound is okay.

Picture has two horizontal
black bars, one on top and
one on bottom.

Missing Secret Lock Code

Some quick and easy tips for fixing problems yourself.

POSSIBLE SOLUTIONS

• Check your antenna connection or location.

• Check your cable input.

• Check to see if the TV/VCR button on your VCR has the TV selected.

• Check your antenna direction and/or location.

• Check your cable input.

• Make sure the cable from your antenna to your TV is

properly connected.

The following may cause image problems or distortion:
Electrical appliances, powerful lights, cars, trucks; computers or
portable phones; medical equipment

• If possible increase the distance between your TV and the offending appliance,
or shut one of them off.

• Check volume levels.

• Make sure the TV is not Muted.

• Try another channel. The problem may be with the broadcast, not your TV.

• Are the Audio cables installed properly?

• Are the wires for external speakers (if you have external speakers)

installed properly?

• Make sure your speakers are turned on in the Audio menu.

• If your audio mode is set to SAP, the program may not have SAP.

• Are you in TV or cable tuning mode, and should be in the other?

• Make sure output channels on all A/V equipment are on the same channel (3 or 4).

• Check that all connections are tight.

• Is the AC power plugged in?

• Check that your AC power cord outlet works. (Test it by plugging in something

else or try another power outlet.)

• Make sure your brightness and audio controls are set properly.

• Try another channel. The problem may be with the broadcast.

• Check the color settings in the Video menu.

• Try another channel. The problem may be with the broadcast.

• The analog caption option may be in Text mode. Select CC 1, in the analog cap-

tion menu.

• Select correct Aspect Ratio in Option menu

• If you forgot your password, when the display asks you to enter the secret code,
press ‘7’, ‘7’, '7’, ‘7’ on the remote control.

Troubleshooting

PAGE 60

206-04007

Troubleshooting (Continued)

SYMPTOM

Remote control doesn’t work.

Menu options can’t be
changed or selected.

No picture or sound
when any non-cable source
is selected.

Weak or no Stereo Sound
when using a stereo VCR.

The PIP inset is black or
lacks contrast.

The PIP inset is “snowy” when
the source is TV.

Time is incorrect.

POSSIBLE SOLUTIONS

• Make sure the batteries are fresh and installed properly.

• Try unplugging your TV for a few minutes,

then plug it back in.

• Check to see if the source equipment has been turned on.

• Make sure that the connections are secure on the back of your TV and on the

source equipment.

• Check to see if all the connections are secure.

• Look in the Audio mode menu to see if all the settings are correct.

• If you are using channel 3 or 4 to view your VCR, stereo sound will not be

available.

• Check to be sure that the PIP source is turned on.

• Check that all the wires are connected properly.

• Check to see if your input source for PIP is set correctly.

• Look to see if the TV/VCR button on your VCR has the TV selected or change

the PIP to another source.

• Make sure the time was set initially. Probably power was lost.

• Reset clock manually.

PAGE 61

206-04007

A list of definitions for some of the words found in this guide.

75 OHM RF CABLE The round cable that comes from an off-air antenna or cable service

provider. Each end looks like a hex shaped nut with a wire sticking
through the middle, and it screws onto the threaded jack on the back of
your TV.

A/V CABLES Audio/Video cables. Three cables - Right audio (red), Left audio (white),

and Video (yellow). A/V cables are used for stereo playback of videocas­settes and for higher quality picture and sound from other A/V devices.

A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box,

or television).

ADD This function lets you add new channels to the channel list in memory

that you’ll scroll through when using your remote.

AMPLIFIER An external device that amplifies sound from a television, CD player, VCR,

DVD or other A/V device.

ANALOG TV Traditional method of representing a television signal as a replica (analog)

of the original picture and sound.

ANTENNA The physical receiver of television signals sent over the air. A large metal

piece of equipment does not always have to be visible for your home to
be using an antenna.

ASPECT RATIO The ratio of the horizontal dimension to the vertical dimension of a pic-

ture. Standard television in the U.S. today is generally transmitted and
displayed in a 4:3 aspect ratio. High-Definition television will normally be
formatted in a wider aspect ratio, assumed to be 16:9.

CAPTIONS A form of subtitling that writes out the dialog for your program on the

screen.

DELETE This function lets you remove channels that you don’t watch from the

channel list in memory.

DIGITAL TV (DTV) A new method of representing a television signal as a series of binary

numbers (1s and 0s). This method allows the signal to be manipulated to
eliminate redundancy and dramatically increase picture and sound quality.

DOLBY DIGITAL Dolby Digital Cinema Sound is made possible by a new digital coding tech-

nique called Dolby AC-3. Dolby AC-3 produces high-quality, 5.1 channel
surround sound which is six discrete separate channels for a full range of
sound. Each channel can carry a different signal simultaneously (front
center, front left, front right, surround left, surround right and subwoofer).

Glossary

PAGE 62

206-04007

Glossary (Continued)

A list of definitions for some of the words found in this guide.

FAVORITE CHANNELS This function created a customized list of your favorite chan-

nels. You can access this group of channels with the SURF but­ton on the remote by pressing SURF repeatedly.

INPUT Refers to the jack that receives a signal into the TV, VCR or

other A/V device.

JACK A connection on the back of a TV, VCR, or any other A/V

device. This includes the RF jacks and the Audio/Video jacks
that are color-coded.

MODE The mode determines the type of device (TV, VCR, Cable, etc.)

that the remote is controlling; remote operating mode.

MONO SOUND Mono (monaural) sound is one channel of sound. On more

than one speaker, all the speakers play the same audio.

OUTPUT Refers to the jack that sends a signal out of a VCR, DVD, or

other A/V device.

PIP This is the most common way to refer to the Picture-In-Picture

(PIP) feature.

SECOND AUDIO Second Audio Programming (SAP) is another, separate, audio

channel available with some programming. Choosing SAP often
refers to listening to audio in another language, such as
Spanish or French.

SIGNAL Picture and sound traveling through cable, or over the air, to

your television screen.

SOURCE The term for the equipment that provides audio and video

information to your TV. Antenna, VCR, DVD players, and Cable
Boxes are examples of sources.

STEREO SOUND Stereo (stereophonic) sound refers to audio that’s divided into

right and left sides.

TEXT Arbitrary text not related to the program.

TUNER Any device that picks up broadcast signals and turns them into

picture and sound.

PROGRAMMING/SAP

PAGE 63

206-04007

Models C30W47

Horizontal Size (inches) 35.86
Height (inches) 23.66
Thickness (inches) 21.73
Weight (pounds) 132.3

Power requirement 120V, 60Hz

Television system American TV Standard, NTSC, ATSC with STB

Television Channel VHF: 2 - 13

UHF: 14 - 69
CATV: 1 - 125
CADTV: 1 - 135

Power consumption (W) 220W

Antenna 75 ohm external terminal for VHF/UHF

Audio Output (W) 7W x 2

Supplied accessories Remote control, batteries 2 size AA (Alkaline battery)

Screen Aspect Ratio 16 : 9

External input ports Video/Audio input (4 set)

Video output (1 set)
S-Video input (3)
Component input (2 set)
Variable audio output (1 set)
DVI-HDTV input (1)
Digital audio optical input (2)
Digital audio optical output (1)
Calibration port (1)
Antenna port (2)

 Copyright 2003, Zenith Electronics Corporation

Design and specifications are subject to change without prior notice.

Product Specifications

Zenith Part No. 206-04007

P/N : 3828VA0395D (AC02SA)

ZENITH ELECTRONICS CORPORATION

Direct-View TV LIMITED WARRANTY – USA

Zenith will repair or replace your product, at Zenith’s option, if it proves to be defective in material or work­manship under normal use, during the warranty period (“Warranty Period”) listed below, effective from the
date (“Date of Purchase”) of original consumer purchase of the product. This warranty is good only to the
original purchaser of the product and effective only when used in the United States, excluding U.S. Territories.

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN
DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. ZENITH WILL NOT BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES OF ANY NATURE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR PROFITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER
DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. Some states do not allow the

exclusion or limitation of incidental or consequential damages or limitation on how long an implied war­ranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal
rights and you may also have other rights that may vary from state to state.

• Damages or operating problems that result from shipping, installation, adjustment of user controls,
calibration, maintenance or failure to maintain, or separate system components; and

• Damages or operating problems that result from normal wear and tear, misuse, abuse, operation outside envi­ronmental specifications or contrary to the requirements or precautions in the Operating Guide, accident, light­ning strikes or other natural causes, unauthorized modification or alteration, incorrect electrical current or volt­age, reception problem caused by inadequate home antenna or faulty antenna connections, computer soft­ware, institutional or commercial use, or other causes not arising out of defect in material or workmanship.

The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.

LG Customer Interactive Center

201 James Record Road
Huntsville, Alabama 35824
http://www.zenithservice.com

THIS LIMITED WARRANTY DOES NOT APPLY TO:

CUSTOMER INTERACTIVE CENTER NUMBERS:

For nearest Authorized Service
Center, Where to buy, Product
Assistance, or Customer
Assistance

Call 1-877-9Zenith (1-877-993-6484) (24 hours a day, 365 days per
year) and select an appropriate option from the menu.

Or visit our website at http://www.zenithservice.com

WARRANTY PERIOD:

LABOR: 90 days from the Date of Purchase.

PARTS: One Year from the Date of Purchase.

PICTURE TUBES: 2 Years from the Date of

Purchase.

*

Parts replaced are warranted for the remain­ing portion of the original warranty period.

HOW SERVICE IS HANDLED:

In-Home Service: Please retain dealer’s dated bill of sale or

delivery ticket as evidence of the Date of Purchase for proof of
warranty, and submit a copy of the bill of sale to the service person
at the time warranty service is provided.

Please call 1-877-9Zenith (1-877-993-6484) to locate
your nearest Zenith Authorized Service Center.

Replacement parts may be new or factory remanufactured.

Visit our website at http://www.zenithservice.com

a