Zebra ZQ110 User Guide

ZQ110

OPOS Driver Setup Utility

P1069381-001
Rev. A

ZQ110

- 2 -

OPOS Driver Setup Utility

Table of Contents

1. Manual Information ........................................................................................................ 6

2. OPOS Driver Setting ...................................................................................................... 6

2-1 POSPrinter Registration ............................................................................................. 7

2-2 Magnetic Stripe Reader (MSR) Registration ............................................................... 8

Rev. 1.00

ZQ110

- 3 -

OPOS Driver Setup Utility

■ Proprietary Statements

This manual contains proprietary information for Zebra Technologies Corporation. It is
intended solely for the information and use of parties operating and maintaining the equip­ment described herein. Such proprietary information may not be used, reproduced, or dis­closed to any other parties for any other purpose without the expressed written permission
of Zebra Technologies Corporation.

Product Improvements
Since continuous product improvement is a policy of Zebra Technologies Corporation, all
specifications and signs are subject to change without notice.

FCC Compliance Statement
NOTE: This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equip­ment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference with radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet or circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure re­quirements this device shall be used in accordance with the operating conditions and in­structions listed in this manual.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
Changes or modifications to this unit not expressly approved by Zebra Technologies
Corporation could void the user’s authority to operate this equipment.

Rev. 1.00

ZQ110

- 4 -

OPOS Driver Setup Utility

Canadian Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
“IC:” before the equipment certification number signifies that the Industry Canada technical
specifications were met. It does not guarantee that the certified product will operate to the
user’s satisfaction.

Liability Disclaimer
Inasmuch as every effort has been made to supply accurate information in this manual,
Zebra Technologies Corporation is not liable for any erroneous information or omissions.
Zebra Technologies Corporation reserves the right to correct any such errors and
disclaims liability resulting therefrom.

No Liability for Consequential Damage
In no event shall Zebra Technologies Corporation or anyone else involved in the creation,
production, or delivery of the accompanying product (including hardware and software) be
liable for any damages whatsoever (including, without limitation, damages for loss of
business profits, business interruption, loss of business information, or other pecuniary
loss) arising out of the use of or the results of use of or inability to use such product, even
if Zebra Technologies Corporation has been advised of the possibility of such damages.
Because some states do not allow the exclusion of liability for consequential or incidental
damages, the above limitation may not apply to you.

Rev. 1.00

ZQ110

- 5 -

OPOS Driver Setup Utility

Copyrights

The copyrights in this manual and the label print engine described therein are owned by
Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software
in the label print engine may result in imprisonment of up to one year and fines of up to
$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.
This product may contain ZPL® , ZPL II® , and ZebraLink™ programs; Element Energy
Equalizer® Circuit; E3® ; and AGFA fonts. Software © ZIH Corp. All rights reserved
worldwide.
ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo,
ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of
ZIH Corp. All rights reserved worldwide.
Monotype® , Intellifont® and UFST® are trademarks of Monotype Imaging, Inc. registered
in the United States Patent and Trademark Office and may be registered in certain
jurisdictions.
Andy™, CG Palacio™, CG Century Schoolbook™, CG Triumvirate™, CG Times™,
Monotype Kai™, Monotype Mincho™ and Monotype Sung™ are trademarks of Monotype
Imaging, Inc. and may be registered in some jurisdictions.
HY Gothic Hangul™ is a trademark of Hanyang Systems, Inc.
Angsana™ is a trademark of Unity Progress Company (UPC) Limited.
Andale® , Arial® , Book Antiqua® , Corsiva®, Gill Sans® , Sorts® and Times New Roman®
are trademarks of The Monotype Corporation registered in the United States Patent and
Trademark Office and may be registered in certain jurisdictions.
Century Gothic™, Bookman Old Style™ and Century Schoolbook™ are trademarks of The
Monotype Corporation and may be registered in certain jurisdictions.
HGPGothicB™ is a trademark of the Ricoh company, Ltd. and may be registered in some
jurisdictions.
Univers™ is a trademark of Heidelberger Druckmaschinen AG, which may be registered in
certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned
subsidiary of Heidelberger Druckmaschinen AG.
Futura® is a trademark of Bauer Types SA registered in the United States Patent and
Trademark Office and may be registered in some jurisdictions.
TrueType® is a trademark of Apple Computer, Inc. registered in the United States Patent
and Trademark Office and may be registered in certain jurisdictions.
All other product names are the property of their respective owners.
All other brand names, product names, or trademarks belong to their respective holders.
© 2014 ZIH Corp.

Rev. 1.00

ZQ110

- 6 -

OPOS Driver Setup Utility

1. Manual Information

This is a manual about how to register and configure the ZQ110 printer with the OPOS
Driver.

Throughout this manual, “OLE for Retail POS” is referred to as “OPOS” and “Unified for
Retail POS” is referred to as “UPOS”.

2. OPOS Driver Setting

1. After OPOS Driver installation, execute “OPOS Setup Utility” to register or configure
POSPrinter.

2. The “OPOS Setup Utility” is located in:

Start>Program>Zebra ZQ110 OPOS Driver>OPOS Setup Utility

Rev. 1.00

- 7 -

OPOS Driver Setup Utility

2-1 POSPrinter Registration

1. Click Add Printer.

2. Set the communication environment for the connected printer, and click OK.

ZQ110

* Please check the 'Log' and 'Binary' checkboxes only, if necessary .
Otherwise, the Hard Drive capacity will not contain other files due to the 'Log'

and 'PRN' checkbox function.

3. Click Checkhealth to see if the printer operates properly.

POSPrinter Check Health Dialog

Rev. 1.00

- 8 -

OPOS Driver Setup Utility

2-2 Magnetic Stripe Reader (MSR) Registration

1. Click Add MSR.

2. Select the MSR model and click Next.

ZQ110

* Please check the 'Log' and 'Binary' checkboxes only if, necessary .
Otherwise Hard Drive capacity will not contain other files due to the
'Log' and 'PRN' checkbox function.

3. Click Checkhealth to see if the MSR operates properly.

MSR CheckHealth Dialog

Rev. 1.00

ZQ110

- 9 -

OPOS Driver Setup Utility

Item

Description

Logical Device Name (LDN) Edit Box

New Logical Device Names can be modified by typing
the name in the box and then pressing OK.

Port Drop List Combo Box

Port setting.

Bits per second Drop List Combo Box

Baud rate setting for the COM port. This setting will be
restricted according to the limitations of the device. If
using a parallel port, this control cannot be set or
referenced.

Bit Length Drop List Combo Box

Bit length setting for the COM port. This setting will be
restricted according to the limitations of the device. If
using a parallel port, this control cannot be set or
referenced.

Parity Bits Drop List Combo Box

Parity setting for the COM port. This setting will be
restricted according to the limitations of the device. If
using a parallel port, this control cannot be set or
referenced.

Stop Bits Drop List Combo Box

Stop bit setting for the COM port. This setting will be
restricted according to the limitations of the device. If
using a parallel port, this control cannot be set or
referenced.

Handshake Drop List Combo Box

Handshake setting for the COM port. This setting will be
restricted according to the limitations of the device.
If using a parallel port, this control cannot be set or
referenced.

Input Buffer (byte) Edit Box

Input buffer size for the COM port. Valid size must be
from 32 to 8192. If using a parallel port, this control
cannot be set or referenced.

Output Buffer (byte) Edit Box

Output buffer size for the COM and LPT port.
Valid size must be from 32 to 4096.

Output Interval Time (msec) Edit Box

Sets the interval between retries (amount of time elapsed
during the Win 32 API Sleep function) if there has been
an error during output.
Valid time value must be from 0 to 9999. For a slave
device, this is disabled.

Input Sleep Time (msec) Edit Box

Sets an interval (amount of time elapsed during the
Win32 API Sleep function : not assistance) to place the
device in sleep mode during input. Valid time value must
be from 0 to 99. For a slave device, this is disabled.

CheckHealth

Invoke the CheckHealth method for this device with
Level = OPOS_CH_INTERACTIVE. This method
provides the status of the printer.

Apply or OK

Save current settings and exit.

Cancel

Discard current settings and exit.

Rev. 1.00

ZQ110

- 10 -

OPOS Driver Setup Utility

* if the system has more ports than the default port range of OPOS Driver Setup Utility,

click Port Range and set the port range.

* If you select a port that is outside of the current range, the device will not operate.

Rev. 1.00

www.zebra.com

Zebra Technologies International, LLC Zebra Technologies Europe Limited

475 Half Day Road Dukes Meadow

Suite 500, Lincolnshire

Illinois 60069 USA

Phone: [phone]

Toll-Free: +1.800.230.9494

Fax: [phone]

Millboard Road

Bourne End

Buckinghamshire, SL8 5XF, UK

Phone: [phone]

Fax: [phone]