5. Error Information ......................................................................................................... 13
5-1 ResultCode List ........................................................................................................ 13
Rev. 1.00
ZQ110
- 3 -
OPOS Driver
Application Develop Guide
■Proprietary Statements
This manual contains proprietary information for Zebra Technologies Corporation. It is
intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission
of Zebra Technologies Corporation.
Product Improvements
Since continuous product improvement is a policy of Zebra Technologies Corporation, all
specifications and signs are subject to change without notice.
FCC Compliance Statement
NOTE: This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference with radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet or circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure requirements this device shall be used in accordance with the operating conditions and instructions listed in this manual.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
Changes or modifications to this unit not expressly approved by Zebra Technologies
Corporation could void the user’s authority to operate this equipment.
Rev. 1.00
ZQ110
- 4 -
OPOS Driver
Application Develop Guide
Canadian Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
“IC:” before the equipment certification number signifies that the Industry Canada technical
specifications were met. It does not guarantee that the certified product will operate to the
user’s satisfaction.
Liability Disclaimer
Inasmuch as every effort has been made to supply accurate information in this manual,
Zebra Technologies Corporation is not liable for any erroneous information or omissions.
Zebra Technologies Corporation reserves the right to correct any such errors and
disclaims liability resulting therefrom.
No Liability for Consequential Damage
In no event shall Zebra Technologies Corporation or anyone else involved in the creation,
production, or delivery of the accompanying product (including hardware and software) be
liable for any damages whatsoever (including, without limitation, damages for loss of
business profits, business interruption, loss of business information, or other pecuniary
loss) arising out of the use of or the results of use of or inability to use such product, even
if Zebra Technologies Corporation has been advised of the possibility of such damages.
Because some states do not allow the exclusion of liability for consequential or incidental
damages, the above limitation may not apply to you.
The OPOS Driver Application DevelopGuide explains how to set and configure a device
and to develop applications to use the Zebra ZQ110 printer with the OPOS driver.
Before using the printer, set and configure the printer using the OPOS Setup Utility.
Throughout this manual, “OLE for Retail POS” is called “OPOS” and “Unified for Retail
POS” is called “UPOS”.
2. Development Environment
2-1 Communication Configuration
Communication Configuration for the serial interface is set in the OPOS Setup Utility.
* Check the default communication setting. For more details, refer to the user manual
included in the printer package.
Rev. 1.00
- 7 -
OPOS Driver
Application Develop Guide
3. Property/Method
Capability Name
1 Color Thermal : ZQ110
CapCompareFirmwareVersion
FALSE
CapPowerReporting
TRUE
CapStatisticsReporting
FALSE
CapUpdateFirmware
FALSE
CapUpdateStatistics
FALSE
CapTransaction
TRUE
CapCoverSensor
TRUE
CapConcurrentRecSlp
FALSE
CapConcurrentJrnSlp
FALSE
CapConcurrentJrnRec
FALSE
CapCharacterSet
TRUE
CapRecUnderline
TRUE
CapRecPageMode
FALSE
CapCuncurrentPageMode
FALSE
CapRecStamp
FALSE
CapRecRotate180
TRUE
CapRecRight90
FALSE
CapRecPapercut
FALSE
CapRecNearEndSensor
FALSE
CapRecMarkFeed
FALSE
CapRecLeft90
FALSE
CapRecItalic
FALSE
CapRecEmptySensor
TRUE
CapRecDwideDhigh
TRUE
CapRecDwide
TRUE
CapRecDhigh
TRUE
CapRecColor
FALSE
CapRecCartridgeSensor
FALSE
CapRecBold
TRUE
CapRecBitmap
TRUE
CapRecBarCode
TRUE
CapRec2Color
FALSE
CapRecPresent
TRUE
3-1 Printer Type
Property value will be determined by the printer type, as shown in the table below.