ZQ110
Mobile Printer User Manual
P1069083-001
Rev. A
- 2 -
ZQ110
Mobile Printer User Manual
Table of Contents
※ Manual Information & Usage Precautions ·································································· 7
1. Content Confirmation ·································································································· 14
2. Product Part Names····································································································· 15
3. Installation & Usage ····································································································· 16
3-1 Battery Installation ······························································································ 16
3-2 Battery Charging ································································································· 16
3-2-1 Battery Charging Usage ··············································································· 16
3-2-2 Single battery charger (Optional) Usage······················································· 17
3-2-3 Cigarette lighter adaptor (Optional) Usage ··················································· 17
3-2-4 Single Docking Cradle (Optional) Usage ······················································ 18
3-2-5 Quad Battery Charger / Quad Docking Cradle (Optional) Usage ················· 19
3-2-5-1 Connecting the cables ·········································································· 19
3-2-5-2 Charging Battery (Printer) ···································································· 20
3-3 Paper Installation ································································································ 21
3-4 Belt Clip Usage ··································································································· 22
3-5 Belt Strap (Optional) Usage ················································································ 23
3-6 Protective Case (Optional) Usage ······································································ 24
3-7 Vehicle holder (Optional) Usage ········································································· 25
3-8 Control Panel Usage ··························································································· 26
3-9 MSR Usage ········································································································ 27
4. Self-Test ························································································································ 28
5. Black Mark Paper Printing ·························································································· 31
5-1 Black mark Function Setting ··············································································· 31
5-2 Auto Calibration Function ··················································································· 31
6. iOS MFi Mode Setting (Optional) ················································································ 32
7. Peripherals Connection ······························································································· 33
7-1 Bluetooth® Connection ························································································ 33
7-2 Wireless LAN ······································································································ 33
7-3 Interface Cable Connection ················································································ 33
8. Printer Cleaning ··········································································································· 34
9. Appendix ······················································································································· 35
9-1 Specifications ······································································································ 35
9-2 Certification ········································································································· 36
9-3 Label Types ········································································································ 38
Rev. 1.00
- 3 -
ZQ110
Mobile Printer User Manual
■ Proprietary Statements
This manual contains proprietary information for Zebra Technologies Corporation. It is
intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission
of Zebra Technologies Corporation.
Product Improvements
Since continuous product improvement is a policy of Zebra Technologies Corporation, all
specifications and signs are subject to change without notice.
FCC Compliance Statement
NOTE: This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference with radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet or circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure requirements this device shall be used in accordance with the operating conditions and instructions listed in this manual.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
Changes or modifications to this unit not expressly approved by Zebra Technologies
Corporation could void the user’s authority to operate this equipment.
Rev. 1.00
- 4 -
ZQ110
Mobile Printer User Manual
Canadian Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
“IC:” before the equipment certification number signifies that the Industry Canada technical
specifications were met. It does not guarantee that the certified product will operate to the
user’s satisfaction.
Liability Disclaimer
Inasmuch as every effort has been made to supply accurate information in this manual,
Zebra Technologies Corporation is not liable for any erroneous information or omissions.
Zebra Technologies Corporation reserves the right to correct any such errors and
disclaims liability resulting therefrom.
No Liability for Consequential Damage
In no event shall Zebra Technologies Corporation or anyone else involved in the creation,
production, or delivery of the accompanying product (including hardware and software) be
liable for any damages whatsoever (including, without limitation, damages for loss of
business profits, business interruption, loss of business information, or other pecuniary
loss) arising out of the use of or the results of use of or inability to use such product, even
if Zebra Technologies Corporation has been advised of the possibility of such damages.
Because some states do not allow the exclusion of liability for consequential or incidental
damages, the above limitation may not apply to you.
Rev. 1.00
- 5 -
ZQ110
Mobile Printer User Manual
Copyrights
The copyrights in this manual and the label print engine described therein are owned by
Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software
in the label print engine may result in imprisonment of up to one year and fines of up to
$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.
This product may contain ZPL®, ZPL II®, and ZebraLink™ programs; Element Energy
Equalizer® Circuit; E3®; and AGFA fonts. Software © ZIH Corp. All rights reserved
worldwide.
ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo,
ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of
ZIH Corp. All rights reserved worldwide.
Monotype®, Intellifont® and UFST® are trademarks of Monotype Imaging, Inc. registered
in the United States Patent and Trademark Office and may be registered in certain
jurisdictions.
Andy™, CG Palacio™, CG Century Schoolbook™, CG Triumvirate™, CG Times™,
Monotype Kai™, Monotype Mincho™ and Monotype Sung™ are trademarks of Monotype
Imaging, Inc. and may be registered in some jurisdictions.
HY Gothic Hangul™ is a trademark of Hanyang Systems, Inc.
Angsana™ is a trademark of Unity Progress Company (UPC) Limited.
Andale®, Arial®, Book Antiqua®, Corsiva®, Gill Sans®, Sorts® and Times New Roman®
are trademarks of The Monotype Corporation registered in the United States Patent and
Trademark Office and may be registered in certain jurisdictions.
Century Gothic™, Bookman Old Style™ and Century Schoolbook™ are trademarks of The
Monotype Corporation and may be registered in certain jurisdictions.
HGPGothicB™ is a trademark of the Ricoh company, Ltd. and may be registered in some
jurisdictions.
Univers™ is a trademark of Heidelberger Druckmaschinen AG, which may be registered in
certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned
subsidiary of Heidelberger Druckmaschinen AG.
Futura® is a trademark of Bauer Types SA registered in the United States Patent and
Trademark Office and may be registered in some jurisdictions.
TrueType® is a trademark of Apple Computer, Inc. registered in the United States Patent
and Trademark Office and may be registered in certain jurisdictions.
All other product names are the property of their respective owners.
All other brand names, product names, or trademarks belong to their respective holders.
©2014 ZIH Corp.
Rev. 1.00
- 6 -
ZQ110
Mobile Printer User Manual
■ Introduction to the ZQ110
This user manual gives you the information you will need to operate the ZQ110 series
printer. For a list of supplemental manuals provided with the ZQ110, please refer to the
Manual Information section.
Unpacking and Inspection
Inspect the printer for possible shipping damage:
• Check all exterior surfaces for damage.
• Open the media cover (refer to “Loading the Media” in the Getting Ready to Print section)
and inspect the media compartment for damage.
• In case shipping is required, save the carton and all packing material.
Reporting Damage
If you discover shipping damage:
• Immediately notify and file a damage report with the shipping company. Zebra
Technologies Corporation is not responsible for any damage incurred during shipment of
the printer and will not cover the repair of this damage under its warranty policy.
• Keep the carton and all packing material for inspection.
• Notify your authorized Zebra re-seller.
Rev. 1.00
- 7 -
ZQ110
Mobile Printer User Manual
1. Windows CE Module Program Manual
This manual provides information on the dll files required for Windows CE application
program development.
2. Windows Driver Manual
This manual provides information on installation and main functions of the Windows
driver for this product.
3. Unified Utility Manual
This manual provides information on the software used to select functions of this
product, modify operation conditions, and so forth.
• VMSM (Virtual Memory Switch Manager)
- Provides information on setting the basic operation conditions of the product, the
use of non-hardware controls and software based virtual switches.
• NV Image Download Manager
- Provides information on downloading image files, such as logos, intended for
repetitive printing.
• Firmware Download Manager
- Provides information on downloading and installing the latest firmware.
4. Bluetooth Connection Manual
This manual provides information on the connection of this product with devices
equipped with Bluetooth functionality (Android/iOS smart phone).
5. Commands Manual
This manual provides information on the protocol and functions of the control
commands that can be used with this product.
6. Code Pages Manual
This manual provides information on each character code page that can be used
with this product.
■ Manual Information
※ Manual Information & Usage Precautions
This user’s manual contains basic information for product usage as well as for emergency
measures that may be required when using the ZQ110 printer.
※ For additional information on the ZQ110, please refer to the following supplemental
manuals:
Rev. 1.00
- 8 -
ZQ110
Mobile Printer User Manual
■ Safety Precautions
When using the ZQ110 printer, please follow the recommended safety regulations
provided below.
Warning
Violating the following instructions may cause serious injury.
1. Do not plug several products into one multi-outlet; this can provoke over-heating and a
fire.
• If the plug is wet or dirty, wipe it before usage.
• If the plug does not fit perfectly in the outlet, do not force it.
• Be sure to use only standard multi-plug outlets.
2. You must use only the supplied adaptor.
• It is dangerous to use other adaptors.
3. Do not pull the cable to unplug.
• This can damage the cable, resulting in a fire or a breakdown of the printer.
4. Keep the plastic bag (used to package the printer) out of children’s reach.
5. Do not plug in or unplug with wet hands.
6. Do not bend the cable by force or leave it under any heavy object.
• A damaged cable may cause a fire.
Rev. 1.00
- 9 -
ZQ110
Mobile Printer User Manual
Caution
Violating the following instructions may cause injury to the user or damage the
printer.
1. If you observe smoke, odor or noise from the printer, unplug it before taking
the following measures:
• Turn off the printer and unplug the unit from the electrical outlet.
• Contact an authorized Zebra Technologies service provider for repair.
2. Keep the packet of desiccant material (silica gel used in the packaging of the printer) out
of children’s reach.
3. Use only approved accessories for your printer; do not disassemble or attempt to
repair the printer yourself.
• Contact your authorized service provider for all service replacements.
• Do not touch the blade of the paper tear bar.
4. Keep liquids and foreign objects away from the printer.
• If any object or liquid falls into the printer, immediately unplug the printer and have it
checked by an authorized Zebra Technologies service provider.
Rev. 1.00
- 10 -
ZQ110
Mobile Printer User Manual
■ Battery Safety Precautions
Make sure you review the user manual carefully prior to product use.
To avoid risks of battery overheating, combustion, and explosion damage and/or decline in
performance and product life, handle batteries carefully and comply with the guidelines
below.
Danger
1. Do not allow liquids to enter or leak into the battery compartment.
2. Do not use or leave the battery in a location exposed to high temperatures.
3. When charging the battery, use the exclusive charger or follow the charging
requirements outlined by Zebra.
4. The battery has clearly delineated positive and negative poles. When inserting the
battery into the charger and/or product, ensure that the battery is properly aligned.
5. Do not heat the battery or place it in a fire.
6. Do not allow the battery’s positive (+) and negative (-) poles to contact any metals. In
addition, do not carry or store the battery with metal items.
7. Do not subject the battery to strong shock.
8. Do not pierce the battery with a sharp object, or hit it with a heavy object. Avoid
accidental short circuiting of any battery. Allowing battery terminals to contact
conductive material will create a short circuit may cause burns and other injuries or
could start a fire.
9. Do not solder the battery.
10. Do not disassemble and/or modify the battery.
11. Do not charge near a source of heat or in direct sunlight.
12. Do not expose the battery to high temperatures over
in a hot or humid place.
13. Do not use the battery if it is damaged or if the exterior is deformed in any way.
Rev. 1.00
60o
C, and do not use or store it
- 11 -
ZQ110
Mobile Printer User Manual
Warning
1. Do not place the battery within the reach of small children to prevent swallowing. If a
child swallows the battery, consult a physician immediately.
2. Do not place the battery in a microwave oven and/or high voltage appliance.
3. Do not combine and use any battery of different capacity and/or type with the primary
battery
4. If during battery usage, storage, or charging, a strange odor or conditions differing from
normal operations, such as condensation, color changes, warping, and so forth, are
detected, remove the battery from the product or charger and discontinue use.
5. If the battery is not charged after the recommended charging time, discontinue charging.
6. If the battery is leaking electrolytic solution and the solution enters the eyes,
immediately rinse the eye with clean water, and consult a physician. Neglecting to do so
may cause permanent eye injuries.
Rev. 1.00
- 12 -
ZQ110
Mobile Printer User Manual
Caution
1. Do not use or leave the battery in a location exposed to high temperatures or intense
direct sunlight.
2. Do not use the battery in a location that is prone to static electricity (above the
recommended levels in the manufacturer’s product warranty).
3. The temperature ranges for battery usage are as follows. Any usage outside of these
ranges may result in the battery overheating, damage, and performance and product life
may be reduced.
a. Charging: 0 ~ 40℃
b. Product Usage: -20 ~ 60℃
c. Storage: -20 ~ 60℃ (30 days)
d. Long-Term Storage: -20 ~ 40℃ (90 days)
4. Please review the ZQ110 Quad Battery Charger Installation Guide carefully for charging
instructions.
5. If, upon first use, a strange odor, overheating, and/or anything deemed out of the
ordinary is detected, discontinue use and contact an authorized Zebra Technologies
service provider.
6. Store the battery in a location that is out of the reach of small children. During usage,
make sure to place the charger and/or product out of the reach of small children.
7. If the battery is leaking and the solution comes into contact with the skin or clothing,
immediately rinse the affected area with clean water.
8. Carefully review the user manual and precautions prior to use.
9. When replacing the battery in the printer, use a battery equivalent to the one originally
installed by the manufacturer. Dispose of used batteries per the instructions provided by
the manufacturer.
Rev. 1.00
- 13 -
ZQ110
Mobile Printer User Manual
Recommended
1. Review the user manual for instructions regarding insertion and removal of the battery
from the printer.
2. The battery ships partially charged. You must charge the battery fully before using the
printer for the first time. To charge the battery, use the exclusive charger provided
with your printer.
3. To avoid improper use of the battery, review the product user manual carefully.
4. Do not charge the battery beyond the normal charging time indicated in the user manual.
5. If you do not plan to use the battery for an extended period of time, remove the battery
from the printer and store in a low humidity location. If you opt to store the printer with
the battery installed, avoid high humidity locations. High humidity may cause
oxidation and a decline in printer performance.
6. Ensure that you turn off the printer after usage (at the end of a work shift).
Neglecting to do so may cause a decline in printer performance.
7. A battery that has not been used over a long period of time may not be sufficiently
charged. If you opt to store the battery for future use, ensure that you charge the battery
to the status recommended by the manufacturer every six months. Neglecting to do so
can cause a decline in battery performance and product life.
8. If the battery terminal is dirty, use a dry cloth to clean prior to use. Neglecting to do so
may cause power stoppages or difficulty in charging the printer.
9. Each battery has a product life. If the usage time of the product has become short,
replace the battery. Wrap the terminals of used batteries with tape to insulate prior to
disposal.
Rev. 1.00
- 14 -
ZQ110
Mobile Printer User Manual
ZQ110
Battery Standard
AC Adaptor
Paper
Power Cord
Belt Clip
CD
Registration Card
※ Optional items
Vehicle Holder
Belt Strap
Cigarette
lighter
Adaptor
USB Cable
Battery with outer
contacts
(for Cradle)
Shoulder Strap
Protective Case
Single Docking
Cradle
Single Battery
Charger
Quad Docking Cradle
Quad Battery Charger
Adaptor for Quad Battery
Charger/Docking Cradle
1. Content Confirmation
If any item is damaged and/or missing, contact your dealer.
Rev. 1.00
- 15 -
ZQ110
Mobile Printer User Manual
Media Cover
Power Button
MSR Slot
Open Button
Paper Feed Button
Cable Connection
Power Connection
Battery
Hole for Mounting Belt Strap /Belt Strap
Interface Cap
2. Product Part Names
• Front
• Rear
Rev. 1.00
- 16 -
ZQ110
Mobile Printer User Manual
1. Insert the battery in the bottom of the
printer, and ensure that you align the
battery hook properly.
2. Push the battery into the slot until you
hear it snap in place.
NOTE
Since the battery is partially charged at the time
of purchase, charge the battery prior to product
use. (Use the AC adaptor or the optional Single
battery charger/Quad battery charger.)
1. Turn off the printer power.
2. Connect the power cord to the AC
adaptor .
3. Open the Interface Cap .
4. Connect the AC adaptor to the
power connector of the printer.
5. Plug the power cord into an electrical
outlet .
CAUTION
The printer may incur serious damage if the AC
adaptor provided by Zebra is not used. Zebra is
not legally liable for any such damages. (The
voltage and electrical current specifications of the
printer and AC adaptor must match.)
WARNING
Turn off the power before charging the
battery for the printer.
①
②
③
3. Installation & Usage
3-1 Battery Installation
3-2 Battery Charging
3-2-1 Battery Charging Usage
Rev. 1.00
- 17 -
ZQ110
Mobile Printer User Manual
1. Connect the power cord to the AC
adaptor .
2. Connect the AC adaptor to the
power connector (on the bottom) of
the single battery charger .
3. Plug the power cord into an
electrical outlet.
4. Insert the battery ④ into the single
battery charger ③ until it snaps in
place.
1. Turn off the printer power.
2. Connect the Cigarette lighter adaptor
① to your car’s cigarette lighter jack.
3. Open the external interface cap ②.
4. Connect the Cigarette lighter adaptor
① to the power connector.
CAUTION
The printer may be seriously damaged if a
cigarette lighter adaptor not provided by Zebra
is used. Zebra is not liable for such damage.
WARNING
Turn off the power before charging the battery
for the printer.
①
② ③ ④
①
②
③
3-2-2 Single battery charger (Optional) Usage
3-2-3 Cigarette lighter adaptor (Optional) Usage
Rev. 1.00
- 18 -
ZQ110
Mobile Printer User Manual
1. Turn off the printer.
2. Slide the printer into the single docking
cradle as shown.
3. Push the printer in until you hear a click.
4. Charging will begin when the printer is
installed.
5. Pull out the printer to remove it.
CAUTION
Please be sure to use the battery with
Outer contacts.
3-2-4 Single Docking Cradle (Optional) Usage
Rev. 1.00
- 19 -
ZQ110
Mobile Printer User Manual
1. Connect the power cord to the adaptor,
and connect the adaptor to the power
connector on the bottom of the Quad
Battery Charger/Quad Docking Cradle.
2. Plug the power cord into a power outlet.
Input power is 100-240VAC, 50/60Hz,
1.0A.
3. When the power is on, the amber,
green, and red LEDs are lit for three
seconds.
WARNING
Use only the designated AC/DC adaptor.
(12VDC, 3A)
3-2-5 Quad Battery Charger / Quad Docking Cradle (Optional) Usage
3-2-5-1 Connecting the cables
Rev. 1.00
- 20 -
ZQ110
Mobile Printer User Manual
1. Using the battery hooks, insert the
batteries into the Quad Battery
Charger as shown.
2. Push the battery in until you hear a
snap.
3. Charging begins as soon as the
battery is completely inserted.
Batteries are charged to
8.4VDC, 0.8A.
4. Lift the hook and pull up to remove
the battery.
1. Turn off the printer.
2. Slide the printer into the Quad
Docking Cradle as shown.
3. Push in the printer until you hear a
click.
4. Charging will begin once the printer
is installed.
5. When charging is complete, pull
out the printer to remove it.
CAUTION
Please be sure to use the battery with
Outer contacts.
NOTE
Battery charging status descriptions are as follows:
LED
Charge Status
Charge Time
Amber LED On
Charging
2.5 hours
Green LED On
Fully Charged
Red LED Blinking
Error
Replace or Reinstall Battery
CAUTION
1. If the red LED on the charger blinks, reinstall the battery.
2. If the red LED continues to blink despite several attempts (4-5 times) to install the battery,
contact your local dealer.
3. The charging time may vary depending on the type of the charger and the ambient
temperature.
3-2-5-2 Charging Battery (Printer)
Rev. 1.00
- 21 -
ZQ110
Mobile Printer User Manual
1. Press the Open button to open the
media cover.
2. Insert the paper as shown. (Remove
the empty core.)
3. Align the paper as shown.
4. Pull out the paper as shown and
close the media cover.
5. Tear off any excess paper toward the
side of the printer.
3-3 Paper Installation
Rev. 1.00
- 22 -
ZQ110
Mobile Printer User Manual
1. Insert the belt clip screw into the belt
clip mounting hole.
2. Tighten the screw of the belt clip with
an object like a coin as shown. (Be
careful to tighten the screw in the
correct direction.)
3. Slide the clip over the belt..
Belt Clip
Coin
Belt
3-4 Belt Clip Usage
Rev. 1.00
- 23 -
ZQ110
Mobile Printer User Manual
1. Insert the belt strap screw into the
belt strap hole.
2. Use a coin to tighten the belt strap
screw as shown.
3. Unfasten the belt strap Velcro.
4. Slide the belt strap over a belt.
5. Fasten the Velcro as shown.
Belt
Belt Strap
Coin
Belt
3-5 Belt Strap (Optional) Usage
Rev. 1.00
- 24 -
ZQ110
Mobile Printer User Manual
1. Open the top cover of the protective
case.
2. Insert your printer into the protective
case as shown.
3. Close the top cover.
4. Using the clip on the back of the
protective case, attach it to the belt.
5. When using the printer, open the
paper discharger as shown.
Note
The clip of the protective case can be rotated
30° for each of two steps (for up to 60°).
Belt
Belt
3-6 Protective Case (Optional) Usage
Rev. 1.00
- 25 -
ZQ110
Mobile Printer User Manual
1. Attach the vehicle holder to the
mount.
2. Adjust the vehicle mount properly,
place the suction plate close to the
glass, and push the lever to fix the
position. (Use the disk pad to mount
it on the dashboard)
3. Slide the printer into the vehicle
holder completely as shown. (Push in
the printer until you hear a click.)
3-7 Vehicle holder (Optional) Usage
Rev. 1.00
- 26 -
ZQ110
Mobile Printer User Manual
This button is used to turn the printer on and off.
When the printer is off, pressing this button for approximately 2
seconds will turn on the power. When the printer is on, pressing this
button for approximately 2 seconds will turn off the power.
To manually feed the paper, press this button.
In addition, self-testing and Hexadecimal Dumping can be done.
1. Refer to “4. Self-Test” for self-test information.
2. Refer to the service manual regarding Hexadecimal Dumping.
1. If three green LEDs are lit, the battery is fully charged.
2. If two green LEDs are lit, the battery is half charged.
3. If one green LED is lit, the battery is at the lowest charge level.
4. If one green LED is blinking, the battery must be charged or
replaced.
1. If the red LED is lit, the media cover is open.
2. If the red LED is blinking, either the paper is out or the print head
is overheated. (Replace the roll of paper or turn off the printer for
at least 10 minutes.)
3. If the red LED continues to blink, it may indicate a more serious
problem with the product. Call your authorized service dealer.
1. If the blue LED is lit, Bluetooth is connected.
2. If the blue LED is blinking rapidly, data is transmitting between
the printer and another device.
3-8 Control Panel Usage
• Power Button
• Paper Feed Button
• Battery Status LED (Green)
• Error LED (Red)
• Bluetooth LED (Blue)
Rev. 1.00
- 27 -
ZQ110
Mobile Printer User Manual
• WIFI (Green, Yellow or Red)
1. Infrastructure mode
a. If the LED is off, the radio has not been found.
b. If the LED is blinking red, signal association.
c. If the LED is blinking yellow, authenticated.
d. If the LED is solid green, strong signal.
e. If the LED is blinking green, weak signal.
f. If the LED is solid red, WLAN Fault (authentication error).
2. Adhoc / WiFi Direct mode
Regardless of signal power, green LED is always blinking.
• Power Save Mode (White)
During Power Save mode, the white LED slowly alternates between
bright and dim. The other LEDs are off.
1. Insert the card as shown and swipe in
either direction (see the arrow).
NOTE
If the card does not register, insert the card and
swipe it again.
3-9 MSR Usage
Rev. 1.00
- 28 -
ZQ110
Mobile Printer User Manual
4. Self-Test
Detailed setting of printer is able to be checked by performing self-test.
• Self-Test Instructions
1. Turn off the printer power and close the media cover.
2. Press and hold the paper feed button and power button simultaneously to turn on the
printer.
3. After printing begins, release the two buttons.
4. To view a printout of the ASCII pattern, press the paper feed button once more.
5. After the ASCII pattern is printed out, the self-test is automatically terminated.
Rev. 1.00
- 29 -
ZQ110
Mobile Printer User Manual
Firmware version :
V01.00 STDa 010114
Butter Capacity : 64K Bytes
Print Density : 100%
Default Codepage : PC437
Print Speed : Max. 90mm/s
Double byte character mode: Off
Font : 12 x 24
Paper out Bell : Off
Low Battery Buzzer : On
Power off time : 15 Min
Idle mode time : 10 Sec
MSR data including sentinel
Character mode : None
MSR read mode : Auto TRACK1/2/3
BATT NTC : OK
Memory switch setup status
Memory S/W1 Memory S/W2
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
ON █ █ ON
OFF █ █ █ █ █ █ OFF █ █ █ █ █ █ █ █
Memory S/W3 Memory S/W4
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
ON █ █ █ █ ON
OFF █ █ █ █ OFF █ █ █ █ █ █ █ █
Memory S/W5 Memory S/W6
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
ON █ █ █ █ ON █ █
OFF █ █ █ █ OFF█ █ █ █ █ █
Memory S/W7 Memory S/W8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
ON █ █ █ ON
OFF █ █ █ █ █ OFF █ █ █ █ █ █ █ █
RF Interface
Bluetooth Firmware version :
1.0.1
Bluetooth BD address :
74F07D205A9D
- Auth. & Encry. are enable
- Connection Mode = 2
Not available WLAN
If you want to continue
SELF-TEST printing,
Please press FEED button.
ASCII
! ”# $ % & ’( ) * + , - ./0 123 456 789 :; < =>? @
”#$%&’()*+,-./ 01 234 56 789:; <= > ?@ A
# $% &’ () *+ ,-./01 23 45 67 89 :; <= >? @A B
$ % &’ () *+ , -. /0 12 34 56 78 9: ;< => ?@ AB C
% & ’( )* +, - ./ 01 23 456789: ;< => ?@ ABCD
& ’ () *+ ,- ./ 01 23 45 67 89 :; <= >? @A BCDE
’ ( )* +, -. /0 12 34 56 78 9: ;< =>?@ABCD EF
() *+,-./0 12345 6789: ;<=>? @ABCD EFG
)*+,-./012345678 9:; <=> ?@ABCDE FGH
*+,-./01 234 567 89: ;<= >?@ ABCD EFG HI
+,-./0123 456 789:;<=>?@A BCDEFGHI J
,-./012345 6789: ;<=>?@A BCDEF GHIJK
-./012345678 9:;<=> ?@AB CD EFGHIJ KL
./0123456789:;<= >?@ABCDEFGHIJKLM
/0123456789:;<=>?@ABCDEFGHIJKLMN
0123456789:;<=>?@ABCDEFGHIJKLMNO
123456789:;<=>?@ABCDEFGHIJKLMNOP
23456789:;<=>?@ABCDEFGHIJKLMNOPQ
3456789:;<=>?@ABCDEFGHIJKLMNOPQR
456789:;<=>?@ABCDEFGHIJKLMNOPQRS
56789:;<=>?@ABCDEFGHIJKLMNOPQRST
6789:;<=>?@ABCDEFGHIJKLMNOPQRSTU
789:;<=>?@ABCDEFGHIJKLMNOPQRSTUV
89:;<=>?@ABCDEFGHIJKLMNOPQRSTUVW
9:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWX
PC437
Pt
ƒ
Pt
ć
Pt
ƒáí
Pt
ƒá íó
Pt
ƒá íó ú
Pt
ƒá íó úñ
Pt
ƒá í óú ñÑ
Pt
ƒá íó úñÑ ª
Pt
ƒá íó úñÑ ªº
Pt
ƒá íó úñÑ ª º¿
Pt
ƒá í óú ñÑ ªº ¿┌
Pt
ƒáí ó úñ Ñ ª º¿┌ ┐
Pt
ƒбнуъсСªº¿┌ ┐½
Pt
ƒб нуъсСªº ¿┌ ┐ ½¼
Pt
ƒб нуъсСª º¿┌ ┐½¼¡
Pt
ƒб нуъсСªº¿ ┌ ┐½¼ ¡«
Pt
ƒб нуъсСªº¿┌ ┐½¼¡« »
Pt
ƒб нуъсСªº¿┌ ┐½¼¡«»▓
Pt
ƒбнуъс С ª º ¿┌ ┐ ½ ¼ ¡«»▓▒
Pt
ƒбнуъсСªº¿┌ ┐½¼¡«»▓▒░
Pt
ƒá í óúñѪº¿┌ ┐½¼¡«»▓▒░┃
Pt
ƒб нуъсСªº ¿┌ ┐½¼¡«» ▓▒░┃┤
Pt
ƒб нуъсСªº¿┌ ┐½¼¡«» ▓▒░┃┤╡
Pt
ƒá íóúñѪº¿┌ ┐ ½¼¡«» ▓▒░┃┤╡╢
Pt
ƒб нуъсСªº¿┌ ┐½¼¡«»▓▒ ░ ┃ ┤ ╡╢╖
*** Completed ***
• Self-Test Printout Sample (For Bluetooth)
Rev. 1.00
- 30 -
ZQ110
Mobile Printer User Manual
Firmware version :
V01.00 STDa 010114
Butter Capacity : 64K Bytes
Print Density : 100%
Default Codepage : PC437
Print Speed : Max. 90mm/s
Double byte character mode: Off
Font : 12 x 24
Paper out Bell : Off
Low Battery Buzzer : On
Power off time : 15 Min
Idle mode time : 10 Sec
MSR data including sentinel
Character mode : None
MSR read mode : Auto TRACK1/2/3
BATT NTC : OK
Memory switch setup status
Memory S/W1 Memory S/W2
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
ON █ █ ON
OFF █ █ █ █ █ █ OFF █ █ █ █ █ █ █ █
Memory S/W3 Memory S/W4
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
ON █ █ █ █ ON
OFF █ █ █ █ OFF █ █ █ █ █ █ █ █
Memory S/W5 Memory S/W6
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
ON █ █ █ █ ON █ █
OFF █ █ █ █ OFF█ █ █ █ █ █
Memory S/W7 Memory S/W8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
ON █ █ █ ON
OFF █ █ █ █ █ OFF █ █ █ █ █ █ █ █
RF Interface
Not available Bluetooth
WLAN firmware version :
Ver 2.0
WLAN MAC address :
cc7a30020517
- System Name : ZQ110
- Network Mode : Adhoc
- Authentication : Open
- Encryption : None
- ESSID : 125
- DHCP : Disabled
- IP : 192.168.1.1
- Netmask : 255.255.255.0
- Gateway : 192.168.1.2
- Port : 9100
- HTTPS : Disabled
- Telnet : Disabled
- FTP : Disabled
- SNMP : Disabled
If you want to continue
SELF-TEST printing,
Please press FEED button.
ASCII
! ”# $ % & ’( ) * + , - ./0 123 456 789 :; < =>? @
”#$%&’()*+,-./ 01 234 56 789:; <= > ?@ A
# $% &’ () *+ ,-./01 23 45 67 89 :; <= >? @A B
$ % &’ () *+ , -. /0 12 34 56 78 9: ;< => ?@ AB C
% & ’( )* +, - ./ 01 23 456789: ;< => ?@ ABCD
& ’ () *+ ,- ./ 01 23 45 67 89 :; <= >? @A BCDE
’ ( )* +, -. /0 12 34 56 78 9: ;<=>?@ABCDEF
() *+,-./0 12345 6789: ;<=>? @ABCD EFG
)*+,-./012345678 9:; <=> ?@ABCDE FGH
*+,-./01 234 567 89: ;<= >?@ ABCD EFG HI
+,-./0123 456 789:;<=>?@A BCDEFGHI J
,-./012345 6789: ;<=>?@A BCDEF GHIJK
-./012345678 9:;<=> ?@AB CD EFGHIJ KL
./0123456789:;<= >?@ABCDEFGHIJKLM
/0123456789:;<=>?@ABCDEFGHIJKLMN
0123456789:;<=>?@ABCDEFGHIJKLMNO
123456789:;<=>?@ABCDEFGHIJKLMNOP
23456789:;<=>?@ABCDEFGHIJKLMNOPQ
3456789:;<=>?@ABCDEFGHIJKLMNOPQR
456789:;<=>?@ABCDEFGHIJKLMNOPQRS
56789:;<=>?@ABCDEFGHIJKLMNOPQRST
6789:;<=>?@ABCDEFGHIJKLMNOPQRSTU
789:;<=>?@ABCDEFGHIJKLMNOPQRSTUV
89:;<=>?@ABCDEFGHIJKLMNOPQRSTUVW
9:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWX
PC437
Pt
ƒ
Pt
ć
Pt
ƒáí
Pt
ƒá íó
Pt
ƒá íó ú
Pt
ƒá íó úñ
Pt
ƒá í óú ñÑ
Pt
ƒá íó úñÑ ª
Pt
ƒá íó úñÑ ªº
Pt
ƒá íó úñÑ ª º¿
Pt
ƒá í óú ñÑ ªº ¿┌
Pt
ƒáí ó úñ Ñ ª º¿┌ ┐
Pt
ƒбнуъсСªº¿┌ ┐½
Pt
ƒб нуъсСªº ¿┌ ┐ ½¼
Pt
ƒб нуъсСª º¿┌ ┐½¼¡
Pt
ƒб нуъсСªº¿ ┌ ┐½¼ ¡«
Pt
ƒб нуъсСªº¿┌ ┐½¼¡« »
Pt
ƒб нуъсСªº¿┌ ┐½¼¡«»▓
Pt
ƒбнуъс С ª º ¿┌ ┐ ½ ¼ ¡«»▓▒
Pt
ƒбнуъсСªº¿┌ ┐½¼¡«»▓▒░
Pt
ƒá í óúñѪº¿┌ ┐½¼¡«»▓▒░┃
Pt
ƒб нуъсСªº ¿┌ ┐½¼¡«» ▓▒░┃┤
Pt
ƒб нуъсСªº¿┌ ┐½¼¡«» ▓▒░┃┤╡
Pt
ƒá íóúñѪº¿┌ ┐ ½¼¡«» ▓▒░┃┤╡╢
Pt
ƒб нуъсСªº¿┌ ┐½¼¡«»▓▒ ░ ┃ ┤ ╡╢╖
*** Completed ***
• Self-Test Printout Sample (For Wireless LAN)
Rev. 1.00
- 31 -
ZQ110
Mobile Printer User Manual
5. Black Mark Paper Printing
5-1 Black mark Function Setting
Black mark paper available at the Black mark mode.
• Setting Operations
1. Turn on the printer power.
2. Open the paper cover and press and hold down the paper feed button for longer than
two seconds.
3. After the buzzer tone is emitted, insert paper and close the cover.
4. Repeat the steps above to return to receipt mode.
• Setting Via Memory Switch
- Please refer to the black mark mode switching section of the Unified Utility tool
5-2 Auto Calibration Function
The Black mark paper printing function requires the recognition of Black mark paper’s
black bar in order to print.
If black mark paper’s black bar are not properly recognized, use the auto calibration
function.
• Auto Calibration Instructions
1. Turn the printer power off while in black mark print mode.
2. Press and hold down the paper feed button and then press the power button.
3. After the following printout is outputted, press the power button to perform auto
calibration.
Select the mode
Auto Calibration: Power Button
Self Test: Feed Button
4. Printer feeds three pages of Black mark paper when performing auto calibration.
Rev. 1.00
- 32 -
ZQ110
Mobile Printer User Manual
6. iOS MFi Mode Setting (Optional)
This product supports Made for iOS (MFi) mode which enables Bluetooth communication
with iOS devices.
• How to enable and disable MFi mode:
1. Turn on the printer.
2. Open the media cover.
3. Press and hold the power button and paper feed button for more than two seconds.
4. Close the cover when you hear a beep.
5. Reboot the printer when the following message is printed:
- iOS mode enable!!
Please Reboot Printer!!
6. To disable MFi mode, repeat the above procedure.
• Check iOS mode:
1. Execute a self-test.
2. If the printed firmware version contains a lowercase “a” (for example: V01.00 STDa),
iOS mode is disabled.
3. If the printed firmware version contains a lowercase “i” (for example: V01.00 STDi),
iOS mode is enabled.
Rev. 1.00
- 33 -
ZQ110
Mobile Printer User Manual
1. The printer can connect to devices
equipped with Bluetooth
communication capability. Make sure
your printer is on and discoverable.
2. Use the Bluetooth connection
function supported by the device to
connect to the printer.
1. This printer supports WLAN
communication in Ad-hoc mode and
Infrastructure mode (AP).
The printer can be connected to
other devices such as PDAs and
PC’s supporting wireless LAN
communication in Ad Hoc mode and
AP in Infrastructure mode.
NOTE
Refer to the Bluetooth/WLAN Manual for more
specific information about.
1. Open the Interface Cap .
2. Connect the USB interface cable
(optional) to the cable connector of
the printer.
NOTE
Use only the USB cables (optional) provided by
Zebra.
3. Connect the interface cable to the
USB port of the device (PDAs, PCs,
etc.).
NOTE
The interface cable that can be connected with
the printer is available in USB type.
①
②
7. Peripherals Connection
This product can communicate with other devices via Bluetooth communication and cable.
7-1 Bluetooth® Connection
7-2 Wireless LAN
7-3 Interface Cable Connection
Rev. 1.00
- 34 -
ZQ110
Mobile Printer User Manual
Caution
Warning
8. Printer Cleaning
If the interior of the printer is dusty, print quality can decline. In such a case, follow the
instructions below to clean the printer.
1) Open the media cover and remove the paper, if present.
2) Clean the printhead (A) using a Zebra cleaning pen. Apply the cleaning pen
from the center to the edge of the printhead (A) for cleaning.
3) Using the cleaning pen, remove the paper dust from the paper detection sensor (B) .
4) Do not use the printer for one to two minutes after cleaning the printhead (A) until
the cleaning agent (from the cleaning pen) has completely evaporated and dried.
5) Insert the paper and close the media cover.
Make sure the printer power is turned off before cleaning.
Wait for two to three minutes after power-off before printhead cleaning because it may be very
hot.
Do not to touch the heating region of the printhead with your hand while cleaning it.
The printhead may be damaged by static electricity.
Avoid scratching the printhead.
Clean the printhead periodically if linerless paper is used. Recommended cleaning period is
after consuming twenty rolls of linerless paper (100 meters), or approximately once a week.
Print quality may be degraded or printhead life may be shortened if it is not cleaned
periodically.
Use only linerless paper that is provided by Zebra. Use of other paper voids product warranty.
Use a Zebra Cleaning Pen; part number. 105950-035 (12 pack).
Rev. 1.00
- 35 -
ZQ110
Mobile Printer User Manual
Item
Description
Printing
Printing Method
Thermal printing
Print Speed
90 mm/sec (Receipt Paper), 60 mm/sec (Linerless Paper)
Resolution
203 DPI
Paper Supply
Mode
Easy paper loading
Character Size
Font A: 12 × 24 Font B: 9 × 17 Font C: 9 × 24
Characters
Per Line
Font A: 32 Font B/C: 42
Character Set
English: 95
Expanded Graphics: 128 × 33 pages
International: 32
Barcode
1 Dimension: UPC-A, UPC-E, Code 39, Code 93, Code 128,
EAN-8, EAN-13, ITF, Codabar
2 Dimension: PDF417, DATAMATRIX, QR Code, GS1 DataBar,
Aztec (optional)
Driver
Windows XP(32/64bit) / WEPOS / 2003 Server(32/64bit) /
VISTA(32/64bit) / 2008 Server(32/64bit) / 7(32/64bit) / 8(32/64bit)
SDK
Windows XP / WEPOS / 2003 Server /
VISTA / 2008 Server / 7 / 8 / CE 3.0 and later
Sensor
Paper End, Media Cover Open
Cutter Type
Tear-Bar
Language
User language supported
Paper
Paper Shape
Receipt
Linerless
Paper Type
Thermal Paper
Thermal Paper
Outer Diameter
of Paper Roll
Max. ø30 mm (1.18 in.)
Max. ø30 mm (1.18 in.)
Width
57.5 ± 0.5 mm (2.26” ± 0.2 in.)
57.5 ± 0.5 mm (2.26” ± 0.2 in.)
Thickness
0.06 - 0.1 mm
(0.0024 in.-0.0040 in.)
0.08 ± 0.008 mm
(0.0031in. ± 0.00031in.)
Reliability
Printer
50 km (Receipt Paper), 10 km (Linerless Paper)
Battery
Rechargeable up to 500 times
Communications
Interface
USB, Bluetooth Class2 V3.0 + EDR
Wireless LAN 802.11 b/g/n
* Communication is enabled only for devices with Bluetooth or
Wireless LAN function.
AC Adaptor
Input
Voltage: 100-250 VAC Current: 0.5A (Max. at 110VA)
Output
Voltage: 8.4 VDC Current: 0.8A
* Charging current and charging time may depend on the type
(option) of charger.
Battery
Type
Lithium-ion
Output
Voltage: 7.4 VDC (Available 8.4-6.8VDC) Capacity: 1200 mAh
Charging Time
2.5 hours
Usage
Conditions
Temperature
Printer: -15-50℃ (5-122℉)
Battery: 0-40℃ (32-104℉)
Battery discharge: -20-60℃ (-4-140℉)
Humidity
Printer: 10-80% RH (No condensation)
Battery: 20-70% RH (Non-condensing, refer to the temperature
conditions on page 8)
Dimensions
Printer
80.1mm × 118.8mm × 37.7mm (3.15 in. × 4.68 in. × 1.48 in.)
Weight
Printer
Printer : 190g (0.42 lbs), Printer + Battery : 242g (0.53 lbs)
Printer + Battery + Paper : 273g (0.60 lbs)
Package: approx. 670g (1.5 lbs)
Accessories
Basic Package
Battery Standard, AC Adaptor, Belt Clip, Paper, Power Cord
Sold Separately
Battery with outer contacts, Protective Case, Shoulder Strap,
Belt Strap, Vehicle Holder, USB Cable, Cigarette Lighter Adaptor,
Quad Docking Cradle, Quad Battery Charger, Single battery
Charger, Single Docking Cradle, Adaptor for Quad Battery
Charger/Docking Cradle
NOTE
9. Appendix
9-1 Specifications
Printer specifications are subject to change without notice.
Rev. 1.00
- 36 -
ZQ110
Mobile Printer User Manual
9-2 Certification
1. WEEE (Waste Electrical and Electric Equipment)
This mark shown on the product or its literature indicates that the
corresponding item should not be discarded at the end of its working life with
other household waste. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate marked
items from other types of waste, and recycle them responsibly to promote
the sustained reuse of material resources. Household users should contact either the
retailer where they purchased this product, or their local government office for details
on where and how they can conduct environmentally safe recycling of such items.
Commercial users should contact their suppliers and check the terms and conditions of
purchase contracts. This product should not be combined with other commercial waste
for disposal.
2. This equipment is for indoor use and all of the communication wiring is limited to the
inside of the building.
3. The switch is the disconnecting device. Turn off switch from any hazard.
4. The following Bluetooth mark D022644 is only applicable to models with the Bluetooth
SIG qualification.
5. Instructions for the correct selection of a suitable Listed Class 2 Power Battery Charger
(Adaptor) including “This product is intended to be supplied by a Listed Battery Charger
(Adaptor) marked “Class 2” and rated output 8.4 V DC, 0.8 A.”
Rev. 1.00
- 37 -
ZQ110
Mobile Printer User Manual
Warning
Lithium-lon Battery pack
<Warning> The battery has the potential risk of overheating, fire and/or explosion. To avoid
such risks, observe the following instructions:
A visibly swollen battery may be dangerous. Contact Zebra or your local dealer.
Only use a Zebra ZQ110 charger.
Keep away from open flames. (Do not place in a microwave.)
Ensure proper ventilation around all sides of the battery pack during use and
storage.
Do not allow the battery port to touch metal items, such as a necklace, coin, key or
clock.
Use only a lithium battery guaranteed by mobile phone manufacturer or Zebra.
Do not disassemble, compress or pierce the battery pack.
Do not drop the battery pack from a high place or subject it to strong shock.
Do not expose the battery to high temperatures over 60oC.
Do not expose to high humidity.
Rev. 1.00
- 38 -
ZQ110
Mobile Printer User Manual
Disposal Directions
Do not dispose of used battery packs carelessly.
Do not burn or throw in a fire to dispose of the battery pack. There is a risk of fire
and/or explosion.
Dispose of battery packs according to the methods defined by your country or region.
Recommendation for Charging
Charge your battery pack according to the instruction manual to avoid risks of fire or
explosion.
FCC compliance Information
This device complies with Part 15 FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause undesired
operation.
Information to the User
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses, and may radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
9-3 Label Types
The label types used with this printer are as follows.
• Rating Labels: PET
• Other Labels: PP, PET
Rev. 1.00
Loading...