Tilt and Rotate Mount
Tilt and Rotate Mount Swingaway Ready (Left-Hand Drive)
Tilt and Rotate Mount Swingaway Ready (Right-Hand Drive)
Installation Guide
Standard Version
Swingaway-Ready
Version
1
Product Description
Dock Description Vehicle Type Tilt & Rotate Description
Tilt and Rotate Mount Swingaway Ready
Left-hand Drive Tilt and Rotate Mount Swingaway Ready (Left-hand Drive)
Tilt and Rotate Mount Swingaway Ready
Tilt and Rotate Mount Swingaway Ready
The Tilt and Rotate Mount is designed for use with Motion mobile docks and mounting kits. The unit provides smooth movement around two axes, which allows the tablet to be easily positioned for the driver
or passenger. The mount utilizes torque devices, so no manual locking in place is required.
The Tilt and Rotate Mount with Swingaway-Ready options are part of a safety solution for Motion vehicle
docks that restrict the use of the tablet display when facing the driver of a vehicle that is in
motion. The Tilt and Rotate Mount provides unrestricted use when the tablet is turned to face the
passenger. For more information, see
http://www.motioncomputing.com/choose/spec_tilt_rotate_mount.htm.
Tilt and Rotate Mount Swingaway Ready (Left-Hand Drive) units are designed for vehicles that have the
steering wheel on the left (US, Canada, and Europe).
Tilt and Rotate Mount Swingaway Ready (Right-Hand Drive) units are designed for vehicles that have the
steering wheel on the right (UK, Australia).
Compatible Motion Products
The Tilt and Rotate Mount is compatible for use with the following Motion mobile docks and mounting
kits.
C5/F5-Series Mobile Dock w/ Key Lock
C5/F5-Series Mobile Dock w/ Key Lock - blank-it
C5/F5-Series Mobile Dock w/ Key Lock - Non-Powered Cradle
C5/F5-Series Mobile Dock w/ Key Lock - blank-it & Swingaway
CL-Series Mobile Dock w/ Key Lock
CL-Series Mobile Dock w/ Key Lock - blank-it
CL-Series Mobile Dock w/ Key Lock - Non-Powered Cradle
CL-Series Mobile Dock w/ Key Lock - blank-it & Swingaway
R12-Series Secure Mobile Dock Tilt and Rotate Mount
R12-Series Secure Mobile Dock with blank-it & Swingaway
Left-hand or Right-hand
Drive
Left-hand Drive Tilt and Rotate Mount Swingaway Ready (Left-hand Drive)
Right-hand Drive
Left-hand or Right-hand
Drive
Right-hand Drive
Left-hand or Right-hand
Drive
Left-hand Drive Tilt and Rotate Mount Swingaway Ready (Left-hand Drive)
Right-hand Drive
Left-hand or Right-hand
Drive (swingaway
function not required)
Tilt and Rotate Mount
(Right-hand Drive)
Tilt and Rotate Mount
(Right-hand Drive)
(Right-hand Drive)
Tilt and Rotate Mount
2
Kit Contents
VESA To Knuckle Plate X 1
Retaining Screws : M4 x 12 Socket Cap Head X 4
Knuckle X 1
M8 Plain Washer X 1
M8 Spring Washer X 1
M8 x 16 Socket Buon Head X 1
Tools Required
5mm A/F hex key
3mm A/F hex key
3
Default Mounting Dimensions
The default shipping conguration of the unit is shown below. The mounting hole pattern is VESA 75mm
x 75mm and equipment can be tted at any of the ve positions shown.
75
Position 1
Position 2
Position 3
Position 4
10
20
30
40
Position 5
97.20
75
Mounting Face
5.50
4
Alternate VESA Plate Position for Extra Height
If required, the VESA Plate can be rotated by 180 degrees to give alternative mounting heights.
1. Using a 3mm A/F hex key, remove the four retaining screws as shown.
2. Rotate the VESA plate 180 degrees and re-t the retaining screws as shown.
5
Alternate Mounting Dimensions
The alternate mounting dimensions are as shown below.
75
Position 1
Position 2
Position 3
Position 4
Position 5
75
5.50
10
20
30
40
170.20
Mounting Face
Example Assembly to Docking Station
with 75mm VESA
6
Tilt and Rotate Mount Swingaway Ready (Left- and
Right-Hand Drive)
The Swingaway-Ready versions of the Tilt and Rotate Mount contain a sensor that can be connected to
docking stations tted with the Swingaway version of the Blank-IT system. Once connected, this system
prevents or restricts driver access to the tablet display when the vehicle is in motion, but allows a passenger to have full access. The sensor cable shown in the illustration below is connected to the Blank-IT
sensor cable that extends from the docking station, which is shown on the following pages.
Please see the notes on the following pages for additional information on assembly to the dock and
cable placement.
Side View
Top View
screw axed
Swingaway Ready
(Right-Hand Drive)
sensor cable
sensor
connector plug
screw axed
Swingaway Ready
(Left-Hand Drive)
7
Assembly to Vehicle Bracket (R12-Series)
The Tilt and Rotate Mount is designed to be tted to a vehicle bracket with a single M8 screw.
For installations using the R12-Series Secure Dock, the sensor cable (if present) should be tted into the slot as
shown before engaging the location lugs on the vehicle bracket. Once engaged, t the washers and M8 screw
in the order shown and securely tighten with a 5mm A/F hex key.
Assembly - Side View Assembly - Rear View
For swingaway ready versions which are
to be connected to the R12-Series Secure
Dock, ensure the sensor cable is located
in this slot
location lugs
example vehicle bracket
location lugs
M8 Plain Washer
M8 Spring Washer
M8 x 16 Socket Button Head Screw
8
Assembly to Dock (R12-Series)
Plug the Swingaway blank-it cable into the mating connector on the R12-Series Secure Dock. The connector is
located behind the backplate of the dock and can be accessed by removing the four screws indicated.
Sensor cable
Swingaway blank-it connector housed here
9
Assembly to Vehicle Bracket (F5/C5 and CL Series)
For F5/C5 Series and CL Series dock installations, cut the plug o the sensor wire (if present) and pass the
sensor wire through the hole in the mounting bracket before engaging the location lugs. Once engaged, t
the washers and M8 screw in the order shown and securely tighten with a 5mm A/F hex key.
Assembly - Side View Assembly - Rear View
location lugs
For Swingaway-Ready versions,
ensure the sensor cable passes
through the hole in the vehicle
bracket prior to connecting.
example vehicle bracket
Sensor connector plug
location lugs
M8 Plain Washer
M8 Spring Washer
M8 x 16 Socket Button Head Screw
10
Assembly to Dock (F5/C5 and CL Series)
The illustration below shows the Tilt and Rotate Mount connected to an example dock.
blank-it sensor cable
Cable Placement—Additional Information
• The sensor cables from the dock and the Tilt and Rotate Mount should be connected after the unit is
tted to the vehicle bracket (not included).
• Trim the cable length to allow for the full range of motion and connect to the docking station
securely. The polarity of the sensor cables is unimportant.
• Soldering the sensor cables is preferred, but screw terminals or crimps are also suitable.
• Ensure the cable connection joint is properly insulated to prevent shorts and to protect the cable
from accidental damage.
11
Important
Observe local vehicle codes and regulations when using this product.
PN 024-02-0378-A01
Motion Computing and Motion are registered trademarks of Motion Computing,
Inc. in the United States and other countries.
All other trademarks are properties of their respective owners.
All rights reserved.
Copyright © 2014 Motion Computing, Inc.
12
Loading...